Specifications
Table Of Contents
- Front cover
- Trademarks
- Contents
- Remedy and measure after a report of error
- I Alarms
- 1. Operation Errors (M)
- 2. Stop Codes (T)
- 3. Servo/Spindle Alarms (S)
- 4. MCP Alarms (Y)
- 5. Safety Observation Alarms (Y)
- 6. System Alarms (Z)
- 7. Absolute Position Detection System Alarms (Z7*)
- 8. Emergency Stop Alarms (EMG)
- 9. Auxiliary Axis Operation Errors (M)
- 10. CNCCPU-side Safety Sequence Alarm(U)
- 11. Multi CPU Errors (A)
- 12. Network Errors (L)
- 13. Program Errors (P)
- II Parameters
- 1. Machining Parameters
- 2. Base Specifications Parameters
- 3. Axis Specifications Parameters
- 4. Servo Parameters
- 5. Spindle Parameters
- 6. Multi-CPU Parameters
- 7. FL-net Parameters
- 8. DeviceNet Parameters
- 9. Machine Error Compensation Parameters
- 10. PLC Parameters
- 11. Macro List
- 12. Position Switches
- 13. PLC Axis Indexing Parameters
- III PLC Devices
- Revision History
- Back cover
II Parameters
FL-net Parameters
II - 127
【#29016(PR)】 Status Data:Word Area Local Node Inform.
Status data: Word area local node information area
Set a device to store the following data:
<1st word: Local node information area>
Stores the parameter information.
(This is enabled when "#29013 Status Data: Bit Area Local Node Inform." 2nd word
area bit1 is set to "0".)
<2nd word: Local node information area>
Stores the data unit applied in the message data area.
0: Word unit
1: Byte unit
<13th word: Local node information area>
Indicates the node No. of the FL-net module.
1 to 249: Node No.
<14th word: Local node information area>
Indicates the mode switch status of the FL-net module.
0: Online
1: Offline
2: Loopback test
3: Hardware test
Others: Setting error
<15th, 16th word: Local node information area>
Indicates the IP address status of the FL-net module.
<17th word: Local node information area>
Indicates switches setting status.
0: Normal
1 and later: Error code
<18th word: Local node information area>
Indicates the Ethernet interface owned by the local node module.
bit0: 10BASE2 (0: No, 1: Yes)
bit1: 10BASE5 (0: No, 1: Yes)
bit2: 10BASE-T (0: No, 1: Yes)
<19th word: Local node information area>
Local node communication status: Indicates data link (cyclic transmission) of local node.
0: During data link
3: Disconnecting (Parameter error detection)
4: Disconnecting (Token monitoring time out)
5: Disconnecting (Node number multiplexing detection)
6: Disconnecting (Receive wait status)
7: Disconnecting (Invalid communication detected)
FE: Initializing
FF: Resetting
<20th word: Local node information area>
Indicates FL-net (OPCN-2) protocol version.
<21st word: Local node information area>
Indicates FL-net (OPCN-2) authorization version.
<22nd word: Local node information area>
Indicates results of local node CPU self diagnosis.
0: Normal
1 and later: Error code
<27th word: Local node information area>
Indicates the maximum No. of node normally communicating (token participation).
<29th word: Local node information area>
Indicates the parameter setting contents status.
0: Normal
1 and later: Error code
15 0
0: Common memory setting - No
1: Common memory setting - Yes
Setting data
Setting conditions
0: Sequence program
1: GX Configurater-FL
41
.41
Authorization
hardware version
Authorization
software version