Specifications
Table Of Contents
- Front cover
- Trademarks
- Contents
- Remedy and measure after a report of error
- I Alarms
- 1. Operation Errors (M)
- 2. Stop Codes (T)
- 3. Servo/Spindle Alarms (S)
- 4. MCP Alarms (Y)
- 5. Safety Observation Alarms (Y)
- 6. System Alarms (Z)
- 7. Absolute Position Detection System Alarms (Z7*)
- 8. Emergency Stop Alarms (EMG)
- 9. Auxiliary Axis Operation Errors (M)
- 10. CNCCPU-side Safety Sequence Alarm(U)
- 11. Multi CPU Errors (A)
- 12. Network Errors (L)
- 13. Program Errors (P)
- II Parameters
- 1. Machining Parameters
- 2. Base Specifications Parameters
- 3. Axis Specifications Parameters
- 4. Servo Parameters
- 5. Spindle Parameters
- 6. Multi-CPU Parameters
- 7. FL-net Parameters
- 8. DeviceNet Parameters
- 9. Machine Error Compensation Parameters
- 10. PLC Parameters
- 11. Macro List
- 12. Position Switches
- 13. PLC Axis Indexing Parameters
- III PLC Devices
- Revision History
- Back cover
II Parameters
Base Specifications Parameters
II - 30
【#1258(PR)】 set30
bit0: Skip I/F switch
Select A or B contact for the skip interface.
0: A contact (Skip operation starts at rising edge of a signal)
1: B contact (Skip operation starts at falling edge of a signal)
(Note) This parameter is not applied to PLC skip.
bit1: Enable Position check excessive detection alarm at power ON
Select the alarm to be output when the machine position at the power OFF/ON is bigger
than a value set in "#2051 check".
0: Z70 0006(Abs posn error) will be output.
1: Z70 0007(position check excessive detection at power ON) will be output.
bit7 : PLC axis buffering mode action changeover
Select the action of rotary axis when issuing an absolute value command to the PLC axis in
buffering mode.
0 : Shift as much as the incremental amount calculated by subtracting current value
from command value.
1 : When short-cut is disabled, follow the sign of the command value. When short-cut is
enabled, take a short-cut to the commanded position.
【#1270(PR)】 ext06
bit5: Coordinate rotation angle without command
Select the operation when there is no rotation angle command R for the L system
coordinate rotation.
0: Use the previously commanded value (modal value). If the command is the first
issued command, the rotation angle will be 0°.
1: Use the set value in "#8081 Gcode Rotat".
bit7: Handle C axis coordinate during cylindrical interpolation
Specify whether the rotary axis coordinate before the cylindrical interpolation start
command is issued is kept during the cylindrical interpolation or not.
0: Do not keep
1: Keep
【#1273(PR)】 ext09
bit0 : Arcsine ASIN calculation result range changeover
Select the notation system for operation result of ASIN.
0: Do not switch minus figures to positive figures. (-90° to 90°)
1: Switch minus figures to positive figures. (270° to 90°)
【#1277(PR)】 ext13
bit0: Tool life management II count type 2
Select how and when the mount or use count is incremented in tool life management II.
0: Type 1 (Default)
Increment the count each time a spindle tool is used for cutting.
1: Type 2
Increment the count by one for a tool that is used or mounted in one program. This
incrementing is done at resetting.
【#1279(PR)】 ext15
bit3: Retaining the asynchronous feed modal during polar coordinate(cylindrical) interpolation
Select whether to retain the asynchronous feed modal during the polar
coordinate(cylindrical) interpolation even after its interpolation is canceled.
Simultaneously, select whether to retain the speed even after the polar
coordinate(cylindrical)interpolation is canceled, in cases where the polar
coordinate(cylindrical) interpolation has been started and the speed is commanded.
0: Do not retain
1: Retain