Specifications
Table Of Contents
- Front cover
- Trademarks
- Contents
- Remedy and measure after a report of error
- I Alarms
- 1. Operation Errors (M)
- 2. Stop Codes (T)
- 3. Servo/Spindle Alarms (S)
- 4. MCP Alarms (Y)
- 5. Safety Observation Alarms (Y)
- 6. System Alarms (Z)
- 7. Absolute Position Detection System Alarms (Z7*)
- 8. Emergency Stop Alarms (EMG)
- 9. Auxiliary Axis Operation Errors (M)
- 10. CNCCPU-side Safety Sequence Alarm(U)
- 11. Multi CPU Errors (A)
- 12. Network Errors (L)
- 13. Program Errors (P)
- II Parameters
- 1. Machining Parameters
- 2. Base Specifications Parameters
- 3. Axis Specifications Parameters
- 4. Servo Parameters
- 5. Spindle Parameters
- 6. Multi-CPU Parameters
- 7. FL-net Parameters
- 8. DeviceNet Parameters
- 9. Machine Error Compensation Parameters
- 10. PLC Parameters
- 11. Macro List
- 12. Position Switches
- 13. PLC Axis Indexing Parameters
- III PLC Devices
- Revision History
- Back cover
II Parameters
Base Specifications Parameters
II - 29
【#1234】 set06
bit5: Enable sampling parameter output
Select whether to enable sampling parameter.
0: Disable
1: Enable
Sampling parameter will be put out only when this parameter is enabled and "#1224 aux08/
bit0" = "1".
【#1236】 set08
bit0: Rotary axis Manual feed rate unit selection
Select the manual feed rate unit for a rotary axis.
0: Fixed to [°/min]
1: Conventional
【#1237(PR)】 set09
bit0: External workpiece offset
Select this function to use the external workpiece coordinates by shifting them to the Z axis.
0: Not reverse the sign of external workpiece offsets (Z shift) (same as conventional).
1: Reverse the sign of external workpiece offsets (Z shift).
(Note) When you choose to reverse the sign of external workpiece offsets (Z shift), do not
measure those external workpiece offsets.
However, you can measure the external workpiece offsets using a tool pre-setter.
【#1239(PR)】 set11
bit0: Coil switching method
0 : Via PLC. (YD3F)
1 : NC internal processing. (YD3F is disabled.)
(Note1) Set to "0" when the system structure requires a mechanical gear for a spindle.
(Note2) When this parameter is set to "1", the spindle speed is clamped to the maximum
speed of the gear 2 ("#3006 smax2" or "#3014 stap2" when tapping) regardless of
the input gear.
bit5 : Enable external spindle speed clamp
Select whether to enable spindle speed clamp function using PLC signal.
0: Disable
1: Enable
bit6 : External deceleration axis compliance valid
Designate the method for setting the external deceleration speed.
0: Set speed common for all axes (#1216 extdcc External deceleration speed)
1: Set speed for each axis (#2086, #2161 - #2165 exdcax1-6 External deceleration
speed 1-6)
【#1240(PR)】 set12
bit0: Handle input pulse selection
Select the handle input pulse.
0: MITSUBISHI CNC standard handle pulse
1: Handle 400 pulse
【#1241(PR)】 set13
bit0 : No G-CODE COMB. Error
Select the operation for when an illegal combination of modal and unmodal G codes are
commanded in a same block.
0：The program error (P45) will occur.
1：A program error can be avoided but the modal G code will be ignored.
【#1245】 set17
bit0: Enable I point in-position check
Select whether to enable I point in-position check.
0: Disable
1: Enable
bit1: Enable R point --> I point in-position check
ect whether to enable R point --> I point in-position check
0: Disable
1: Enable