Specifications

II Parameters
Base Specifications Parameters
II - 12
【#1093】 Wmvfin Synchronization between part systems method
Select the timing of synchronization between part systems when using the multi-part
system.
When the travel command is found in the synchronization command (!) block:
0: Synchronize before executing travel command
1: Synchronize after executing travel command
【#1094】 Tl_SBK Select life count for single block (for L system only)
Select whether to count the data units to be used for single block operation when using the
tool life management II function (L system).
0: Not count
1: Count
【#1095】 T0tfof TF output (for L system only)
Select how to handle TF for T00 command.
0: TF will be output
1: TF wont be output
【#1096(PR)】 T_Ltyp Tool life management type (for L system only)
Select the tool life management type.
1: Life management l
In this type, how long and how many times the program commanded tool is used are
accumulated to monitor the usage state.
2: Life management ll
This method is the same as tool life management I, but with the spare tool selection
function.
A spare tool is selected from a group of tool commands commanded in the program.
Tool compensation (tool length compensation and tool radius compensation) is
carried out for the selected tool.
【#1097】 Tldigt Tool wear compensation number 1-digit command
Select the number of digits of the tool wear compensation No. in the T command.
0: The 2 high-order digits are the tool No., and the 2 low-order digits are the wear
compensation No.
1: The 3 high-order digits are the tool No., and the 1 low-order digit is the wear
compensation No.
This parameter will be fixed to “0” when tool life management II is selected.
【#1098】 Tlno. Tool length offset number
Select the number of digits of the tool length compensation No. in the T command.
0: The 2 or 3 high-order digits are the tool No.
The 2 or 1 low-order digits are the tool length compensation and wear compensation
Nos.
1: The 2 or 3 high-order digits are the tool No. and tool length compensation Nos.
The 2 or 1 low-order digits are the wear compensation No.
【#1099】 Treset Cancel tool compensation amount
Select how to handle the tool compensation vector when resetting the system.
0: Clear the tool length and wear compensation vectors when resetting
1: Hold the tool length and wear compensation vectors when resetting
When the values are cleared, the compensation will not be applied. So the axis will be
shifted by the compensation amount in the next compensation operation.
When the values are kept, the compensation will be applied, so the axis will shift the
differential amount of the compensation amount in the next compensation operation.
【#1100】 Tmove Tool compensation
Select when to perform tool length compensation and wear compensation.
0: Compensate when T command is executed.
1: Superimpose and compensate with the travel command in the block where the T
command is located. If there is no travel command in the same block, compensation
will be executed after the travel command is superimposed in the next travel
command block.
2: Compensate the wear amount when the T command is executed. Superimpose and
compensate the tool length compensation amount with the travel command in the
same block. If there is no travel command in the same block, compensation will be
executed after the travel command is superimposed in the next travel command
block.
【#1101】 Tabsmv Tool compensation method
Select the type of travel command when “#1100 Tmove” is set to “1” or “2”.
0: Compensate regardless of the travel command type
1: Compensate only at the travel command in the absolute command
【#1102】 tlm Manual tool length measuring system (for L system only)
Select the measurement method for manual tool measurement l.
0: Align tool with basic point
1: Input measurement results
【#1103】 T_Life Validate life management
Select whether to use the tool life management.
0: Not use
1: Use