English This watch is an analog (hand) display diver's watch equipped with an electronic depth meter. The familiar watch-face format is convenient to confirm depths while diving. Further, a chronograph function finds uses in a variety of activities besides diving. (Please note that the depth meter function should be used only as an auxiliary instrument.) "Highly reliable water resistant for use at depths of up to 200 meters" The high-reliability water resistant conforms to ISO standards for diving watches.
Table of contents Diving with this watch················································································· 6 Safe diving··································································································· 7 Do not use the depth meter when······························································· 8 Stop using this product while diving when··················································· 9 Operating instructions·····························································
Diving with this watch Diving can be a safe, enjoyable activity when diving rules are properly followed. It is always, however, accompanied by certain risks including diver's paralysis and unanticipated accidents. Before diving please obtain proper diving instruction and be sure to conduct safety checks. Please use this watch only after you have read and fully understood the operating procedures and cautions in these instructions.
WARNING: 7.Avoid rapid ascents when diving, as these adversely affect the human body, including causing diver's paralysis. Maintain a safe ascent speed while diving. An ascent of 10 meters(33ft) or less per minute is recommended for sports diving to avoid various possible problems. [ Do not use the depth meter when... ] 1.In locations with altitudes exceeding 4,000 meters(13,124ft). The watch will be unable to measure depth accurately. 2.In temperatures outside of the warranted temperature range.
Please read the instructions below while referring to the foldout watch diagram located on the opening page of this manual. E : Hour hand F : Second hand Used to set time and date 0m 1 The function hand A and the mode hand B both point to 0. 3 IT EX 0m 6 40 20 6 50 10 40 20 DV 12 30 The second hand F points to 0. .2 Time Mode 40 40 40 1 1 15 15 15 .2 1 12 30 .8 .6 .4 1 1 30 30 Chronograph Mode Diving Mode 30 For 3 DV 10 .0 .4 0m IT EX DV 50 .0 .
Time Mode B IT EX A DV 50 E 10 40 C 20 30 24 20 About the Time Mode 1. The Time Mode displays both 12 and 24hour time. 2. With the exception of the second hand, the time may be read even while using the other modes. 4 7 16 8 12 G : Switch to the Time Mode from the Diving Mode by pressing button 1 continuously for 2 seconds. Switch to the Time Mode from the Chronograph Mode by pressing button 1 once. .0 .8 .6 .2 F .
Diving Mode [ Maximum depth memo function ] 3 IT EX 6 DV C 20 4 15 16 8 .0 .8 .2 20 .4 This watch automatically records the maximum depth reached during a dive (in 1 meter(2.5ft) increments). This memo is retained until the watch is set to the Diving Mode again and a depth of 1 meter(5ft) or more is reached. Reading the Depth While diving, the number indicated by the depth indicator hand A (the function hand) is the present diving depth.
[ Making accurate depth readings ] 1.Switch the watch to the Diving Mode shortly before diving. 2.When there is a great difference between the air and water temperature, immerse the watch in the water for 2-3 minutes before switching it to the Diving Mode. 3.Confirm that the mode hand points to DV and the function hand points to 0 when the watch is switched to the Diving Mode. If the hands are in the wrong position please refer to ALL RESET on page 23. 4.Avoid too rapid descents and ascents when diving.
Chronograph Mode : Switch from the Time Mode to the Chronograph Mode by pressing button 1 once. About chronograph measurements 1.A maximum of 50 minutes may be measured by the chronograph. After 50 minutes (1/20 second=0.05 second increments) measurement will stop automatically and chronograph will return to the reset position. 2.The chronograph 1/20 second hand will move for 30 seconds, after which it will return to stand-by at the 0 position.
In these cases... [ When the second hand moves in 2-second increments ] Please refer to the fold-out watch diagram located on the opening page of this manual. When the battery is low, the low-battery warning indicator causes the second hand to move in 2-second increments. The Diving Mode and the Chronograph Mode will return to the Time Mode. Replace the battery soon.
[ After the battery is replaced or if the hands are in the wrong position ] Please refer to the fold-out watch diagram located on the opening page of this manual. Use the following ALL RESET operation to adjust the position of the hands if: 0m 3 IT EX 2 6 DV 50 10 9 50 20 30 B A 12 40 15 .0 .8 F .2 20 40 .6 .4 1 30 22 □In the Time Mode The function hand A does not point to EXIT. The mode hand B does not point to 0. □In the Diving Mode The function hand A does not point to 0.
[ When the function hand is in the wrong position ] Please refer to the fold-out watch diagram located on the opening page of this manual. *If, when switching from the Time Mode to the Diving Mode, the function hand does not point to 0. *If, when switching from the Time Mode to the Chronograph Mode, the function hand does not point to 0. In these cases, use the crown and buttons as follows to adjust the position of the hand.
Other functions 40 0m 3 6 50 9 50 30 IT EX 12 20 20 15 40 30 10 d pse Ela 26 Before diving, rotate the register ring to line up the mark with the minute hand. Elapsed time is then indicated by the position of the minute hand on the register ring. Example: In the diagram at left the minute hand is 10 minutes past the mark, indicating that 10 minutes has elapsed.
Water resistance Indication Water-related use Watch Dial Water Resist 200m Water resistant 200m Light spray, perspiration, light rain, bathing etc. OK Swimming, etc. OK Skin diving. (Without air tank) Scuba diving. (With air tank) When diving using a helium enriched environment. Pulling out the crown when the watch is wet. OK OK NO NO 28 hol, gasoline, thinner or other chemical substances. • If you cannot clean the sensor, bring the watch to the Citizen Service Center.
diate vicinity of strong magnetism, however, the watch’s functions may temporarily be affected. 7) Static electricity The integrated circuits used in the watch are sensitive to static electricity. If exposed to intense static electricity, the watch’s display may lose its accuracy. 8) Chemicals and Gases Avoid wearing the watch in the presence of strong chemicals or gases.
Specification 1. Model 2. Accuracy of time measurements (within normal temperature range) 3. Accuracy of depth readings 4. Display 5. Timepiece operational temperature range 6. Display functions 32 Analog depth meter with chronograph ±20 seconds/month 1m(5ft)∼10 m(25ft):± 1m(5ft) 11m(27.5ft)∼50m(125ft):±2m(7.
34
