INST RUCT ION M ANUAL 2.
IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following 1. 2. 3. 4. 5. 6. 7. 8. 9. a. b. c. d. e. f. Read and understand all instructions Do not use the telephone near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet base, or near a swimming pool.
CONSERVER CES INSTRUCTIONS FEATURE LIST: BATTERY SAFETY 2.4GHz Operation Frequency. 40-Channels Auto-Scanning or Manual Selectable. CAUTION: 1’048’576 Automatic Digital Security Code. To reduce the risk of fire or personal injury, read and follow these instructions: 1. Pre-Dialing with Clear LCD for Handset. Use only the following type and size battery pack: Flash and Last Number Redial Function. SANIK 03/01 Low battery Indicator on LCD. Ni-Cd AA 300mAh 3.6V, CHARGE LED Indicator.
NOTE: Before initial use, put you handset for CHARGE MODE to charge the handset for 12 hours. 2.4GHz REDIAL FLASH TALK 1 2 ABC 3 DEF 4 GHI 5 JKL 6 MNO 7PQRS 8 TUV 9 WXYZ * 0 # CH. MEMO PAUSE Figure 1 CID 2. UP 45° POSITION (see Figure 2) DOWN With the back of the base unit facing up, insert the hooks of the mounting ON/OFF PAGE PAGE CHARGE CHARGE 2.4GHz 2.4GHz bracket into to the matching slots of the base unit, as specified in figure 2.
2. 3. telephone jack. Insert the free end of the line cord through the hole of the Reset Your Security Code ---Important Steps! mounting bracket. 1. Insert the hooks of the mounting bracket into the matching slots the base Remove the Handsets unit from the base then press and hold down PAGE button on the Base unit about 5 second. unit (as shown below). Then slide the mounting bracket into place. Plug the 2. Press CODE button on the Handset.
SELECTING CHANNEL PAUSE FUNCTION During conversation, you might need to manually channel in order to get rid of static. Press “CH.” button to seek clear channel. To dial a number from an automatic switch board system (PABX), you must first dial an access code. Then pause a few second to wait for an outside line. The T/P DIALING SELECTOR “REDIAL” button stores a 2-3 seconds pause to give the automatic switchboard You can choose the type of dialing by selecting TONE/PULSE mode.
4. In case the phone number is a long-distance number, add a long distance number by press 0 or 1. 5. If you want to dial a number without area code, press 7 to dialing out last Problem solving section seven number, or press 8 to dialing out last eight number. For your assistance, we have listed below a few common problems. TO EDIT PHONE NUMBER WITH NAME 1. In the stand by mode, press STORE button, the LCD will show: “XX memories”. 2. Press SET button to enter edit phonebook entry. 3.
Consumer Information: This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user in encouraged to try to correct the interference by one or more of the following measures. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.
