Member of: OWNER'S MANUAL 150 Lb. Laundry Dryer MODELS GAS STEAM L50CD42G C150G L50CD42S C150S CISSELL MANUFACTURING COMPANY HEADQUARTERS 831 SOUTH FIRST ST. P.O. BOX 32270 LOUISVILLE, KY 40232-2270 PHONE: (502) 587-1292 SALES FAX: (502) 585-3625 SERVICE/PARTS FAX: (502) 681-1275 THIS MANUAL MUST BE GIVEN TO THE EQUIPMENT OWNER.
IMPORTANT NOTICES—PLEASE READ For optimum efficiency and safety, we recommend that you read the Manual before operating the equipment. Store this manual in a file or binder and keep for future reference. WARNING: For your safety, the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury, or loss of life. - Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance.
WARNING: To avoid fire hazard, do not dry articles containing foam rubber or similar texture materials. Do not put into this dryer flammable items such as baby bed mattresses, throw rugs, undergarments (brassieres, etc.) and other items which use rubber as padding or backing. Rubber easily oxidizes causing excessive heat and possible fire. These items should be air dried. WARNING: Synthetic solvent fumes from drycleaning machines create acids when drawn through the dryer.
ATTENTION: L’ACHETEUR DOIT PLACER L’AVERTISSEMENT SUIVANT DANS UN ENDROIT CLAIR ET VISIBLE: AVERTISSEMENT. Assurez-vous de bien suivre les instructions donnees dans cette notice pour reduire au minimum le risque d’incendie ou d’explosion ou pour eviter tuot dommage materiel, toute blessure ou la mort. __ Ne pas entreposer ni utiliser d’essence ni d’autres vapeurs ou liquides inflammables dans le voisinage de cet appareil ou de tout autre apparell.
CISSELL DRYER WARRANTY The Cissell Manufacturing Company (Cissell) warrants all new equipment (and the original parts thereof) to be free from defects in material or workmanship for a period of two (2) years from the date of sale thereof to an original purchaser for use, except as hereinafter provided.
TABLE OF CONTENTS 150 LB. LAUNDRY DRYER PAGE Model Numbers & Company Address ....................................................................... 1 Important Notices ...................................................................................................... 2-4 Dryer Warranty .............................................................................................................. 5 Table of Contents ..........................................................................................
SYMBOLS The following symbols are used in this manual and/or on the machine. The numbers between () refer to the numbers on the machine surveys.
SYMBOLS Symbol Description rotation in two directions rotation dans les deux sens Drehbewigung in zwei Richtungen movimiento rotativo en los dos sentidos direction of rotation sens de mouvement continu de rotation Drehbewegung in Pfeilrichtung movimiento giratorio o rotatorio en el sentido de la flecha End of Cycle caution attention Achtung atencion; precaucion Page 8 P a r t / M e a s u re m e n t
Unpacking/General Installation (All Dryers) UNPACKING This dryer is packed in a large wooden crate. Upon arrival of the equipment, any damage in shipment should be reported to the carrier immediately. Upon locating permanent location of a unit, care should be taken in movement and placement of equipment. See outline clearance diagrams for correct dimensions. Remove all packing material such as: tape, manuals, skid, etc. Leveling: Use spirit level on top of dryer.
General Installation (All Dryers) Before operating dryer, open basket door and remove blocking between front panel and basket. Read the instruction tags, owner's manual, warnings, etc. GENERAL IMPORTANT REPLACEMENT PARTS PROCEDURE FOR DISASSEMBLING THE TOP OF THE DRYER The dryer is so designed that when an operator opens the dryer door, the basket and exhaust fan stop. You can expect fast drying from this laundry dryer.
150 lb.
150 lb. Dryers - Specifications GENERAL SPECIFICATIONS FOR 150 lb. DRYERS Floor Space .......................................... 64” (1626 mm) Deep x 54” (1372 mm) Wide x 96” (2439 mm) High Doors .................................................... 31-1/4” (794 mm) Diameter Basket Size .......................................... 50” (1270 mm) Diameter x 42” (1067 mm) Deep Basket Capacity (Dry Weight) ........ 150 lbs. (68.0 kg) Dryweight Basket Motor ...................................... 1-1/2 HP (1.
Gas Pipe Size Chart TOTAL BTU/HR (for LP Gas correct total Btu/h below by multiplying by .6) TOTAL KCAL HOUR GAS PIPE SIZE FOR 1000 Btu (252 kcal/h) NATURAL GAS AT 7” w. c. (17.5 bar) PRESSURE In figuring total length of pipe, make allowance for tees and elbows. (25 ft.) (50 ft.) (75 ft.) (100 ft.) (125 ft.) (150 ft.
Gas Piping Installation (Illustration) Page 14
Gas Piping Installation STEAM PIPING INSTALLATION 1. Gas service installation must conform with local codes, or in the absence of local codes with the National Fuel Gas Code, ANSI Z223.1 or the CAN/CGA-B149, Installtion Codes. 2. Check Rating Plate located on rear wall of dryer, for type of gas to equip the dryer and the altitude (elevation). 3. Check with the gas supplier for the gas pressure and the proper gas supply line installation.
150 lb.
150 lb. Steam Heated Laundry Dryers - Specifications GENERAL SPECIFICATIONS FOR 150 lb. LAUNDRY DRYERS (STEAM HEATED) Operating Steam Pressure 100 psig (6.9 bar) Maximum Boiler HP 12.5 HP (9.33 kW) Heat Capacity 8 Coil Steam Coils (4) 6”(153 mm) x 10 1/4” (261 mm) x 40 1/2”(1029 mm) Steam Supply Connection 3/4” (20 mm) Steam Return Connection 3/4” (20 mm) Trap Connection (2) 3/4” (20 mm) Maximum Air Displacement 2250 cfm (63.7 m³/h) LIST OF MOTORS USED 150 lb. LAUNDRY DRYERS Motor No.
150 lb. Steam Heated Laundry Dryers - Specifications ELECTRICAL CONNECTIONS ALL DRYERS Dryers must be electrically grounded by a separate #14 or larger green wire from the grounding terminal within the Service Connection Box to a cold water pipe. In all cases, the grounding method must comply with local electrical code requirements; or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or the Canadian Electrical Code, CA C22.1. See wiring diagram furnished with dryer.
Steam Dryers - Installation Instructions STEAM DRYERS INSTALLATION INSTRUCTIONS 1 . The dryer comes in two wood crates: A - Very large crate B - Smaller crate 2 . Open Crate A and lift dryer off the skid and set in place. 3 . Open Crate B. It contains two assemblies: I - Control Box Assembly II - Steam Bonnet Assembly 4 . Place II - Steam Bonnet Assembly on top of the dryer and slide piped end to rear of dryer. Bolt to top with six 3/8” ( 10 mm) bolts, flat washers and lockwashers provided.
I - Control Box Assembly and II - Steam Bonnet Assembly (Illustration) I - Control Box Assembly II - Steam Bonnet Assembly Page 20
Steam Piping - Installation Instructions STEAM PIPING INSTALLATION INSTRUCTIONS 1. Set and anchor dryer in position. Machine should be level assure proper steam circulation. 2. To prevent condensate draining from headers to dryer, piping should have a minimum 12” (305 mm)above respective header. Do not make steam connection to header with a horizontal or downwardly facing tee or elbow. 3. Whenever possible, horizontal runs of steam lines must drain, by gravity, to respective steam header.
Steam Piping Installation (Illustration) INDIVIDUALLY TRAPPED COILS ARE RECOMMENDED RATHER THAN MANFOLDING RETURN INTO ONE TRAP.
Dryer Installation with Multiple Exhaust (Illustration) Page 23
Dryer Installation with Multiple Exhaust DRYER INSTALLATION WITH MULTIPLE EXHAUST For Exhaust Duct more than 14 feet (5 m) and 2 elbows equivalent and more than 0.3 inches (8 mm) static pressure. (See illustration on previous page.) 1. Make-up air from outside building may enter enclosure from top or side walls. (See Dryer Make-up Air Requirements Chart) 2. Use constant diameter duct with area equal to the sum of dryer duct areas. EXAMPLE: 6-8 inch (153-204 mm) diameter duct = 1-19.
Dryer Installation with Multiple Exhaust For Exhaust Duct less than 14 feet (5 m) and 2 elbows equivalent and less than 0.3 inches (8 mm) static pressure. DRYER EXHAUSTS Area of section “A-A” must be equal to the sum of dryer exhaust pipes entering multiple exhaust pipe. (See chart below.) No. of Dryers Duct Diameter (in inches) (in CM) No. of Dryers Duct Diameter (in inches) (in CM) No.
Suggested Minimum Dryer Make-up Air Requirements Dryer Model C 30 ST C 75 ST C 110 C 110 E/S C 125 C 150 HD175 HD190 HD20.1 HD30SL HD30.1 HD50.1 HD75.1 HD80.1 Dryer Pocket Capacity lb kg 30 13.6 75 34 110 50 110 50 125 56.7 150 68 175 79.4 190 86.2 20 9.1 30 13.6 30 13.6 50 22.7 75 34 80 36.3 Maximum Air Flow Duct Size For Required Make-up Rate per Pocket Service Connection Air Area per Pocket cfm m3/h inch mm sq.
Dryer Installation with Separate Exhaust (Preferred) DRYER INSTALLATION WITH SEPARATE EXHAUST (PREFERRED) For ductwork less than 14 feet (5 m) and 2 elbows equivalent and less than 0.3 inches (8 mm) static pressure. NEVER exhaust the dryer into a chimney. NEVER install wire mesh screen over the exhaust or make-up air area. NEVER exhaust into a wall, ceiling, or concealed space. 1. Make-Up Air opening from outside the building may enter the enclosure from the top or side walls.
Exhaust and Venting DRYER AIR FLOW INSTALLATION Nothing is more important than air flow for the proper operation of a clothes dryer. A dryer is a pump which draws make-up air from the out-of-doors, through the heater, through the clothes and then forces the air through the exhaust duct back to the out-of-doors. Just as in a fluid water pump, there must be the proper fluid air flow out of the exhaust duct.
Rules for Safe Operation of your Dryer RULES FOR SAFE OPERATION OF YOUR DRYER RULES 1. Be sure your dryer is installed properly in accordance with the recommended instructions. 2. CAUTION Be safe - Shut main electrical power supply and gas supply off externally before attempting service. 3. CAUTION a . Never use dry cleaning solvents: gasoline, kerosene, or other flammible liquids in the dryer. FIRE AND EXPLOSION WILL OCCUR! b. Never put fabrics treated with these liquids into the dryer. c.
Rules for Safe Operation of your Dryer CAUTION Synthetic solvent fumes from dry cleaning machines create acids when drawn through the dryer. These acid fumes cause rusting of painted parts, pitting of bright plated parts and completely removes the zinc from galvanized metal parts, such as the tumbler basket. If the dry cleaning machines are in the same area as the tumbler, then the tumbler make-up air must come from a source free of solvent fumes.
Two Timer Models—Figures 1, 2, and 3 (Illustrations) Page 31
Operating Instructions - Two Timer Models OPERATING INSTRUCTIONS - TWO TIMER MODELS 1. After loading the dryer tumbler with water washed clothes load, proceed to close the loading door. For better drying, do not load dryer with combination of garments that twist. 2. Turn the 60-minute drying timer to the desired drying time. The drying cycle light will be on and indicate the drying. The light shuts off when drying time is complete. (See figure 1 on page 30.) 3.
Moisture Control (Illustration) Page 33
Operating Instructions - Moisture Control Models (Optional) OPERATING INSTRUCTIONS MOISTURE CONTROL MODELS (OPTIONAL) NOTE: Machines with Moisture Control option can be used like regular two-timer models. To dry with Two Timer method, flip switch on Control Panel to “Time Drying”. To dry with the Moisture Control method, flip the switch to “Automatic Drying”. The indicator light will be on while the machine is in operation. 1.
Service Savers TROUBLESHOOTING To help you troubleshoot the dryer, we list below the most common reasons for service calls and some answers to the problems. Before you call service, please review the following items: DRYER WON'T START DRYER WON'T START 1. Is the door completely closed? 2. Are the controls set to the “on” position? 3. Did you push the “start” control? 4. Has a fuse blown or a circuit breaker tripped? 5. Are the fuses tight? 6. Check for low voltage. DRYER WON'T HEAT DRYER WON'T HEAT 1.
Troubleshooting TROUBLE Dryer runs, but no heat. Chart CAUSE Line fuse or heater circuit fuse blown to unit. Defective door switch. Air switch not operating. Air switch out of adjustment. Air switch defective. Gas pressure too low. Improper orifice. Electric power to heating unit turned off. REMEDY Replace fuse. Replace door switch. Clean out lint compartment daily. Check back draft damper for foreign objects, lint accumulation or other causes that may prevent damper from opening.
Troubleshooting TROUBLE Dryer runs, but no heat (continued). Main burners burning improperly. Low gas flame or high gas flame. Dryer too hot. Chart CAUSE Defective relay. Defective thermostat. Defective safety overload thermostat. Lint compartment door open. Incorrect voltage. No voltage. Lint door OPEN. Defective Gas Valve. Gas turned OFF. Spark Igniter not igniting gas. Burner air shutters closed. Dirt in burner. Gas pressure too high. Orifice too large. Restricted or blocked exhaust.
Troubleshooting TROUBLE Motors will not start. CAUSE No power. Incorrect power. Motor tripping on thermal overload. Time off. Loose wiring connections. Defective starting relay. Motor internal overloads have tripped (only on MTR30X series). Low voltage. Inadequate wiring. Loose connections. Inadequate air. Basket motor will not run. Basket will not reverse. Chart Poor housekeeping. Loading door open. Door switch out of adjustment. Defective door switch. Defective basket motor contactor.
Troubleshooting TROUBLE Dryer does not stop at end of time period (6). Dryer runs, but no steam to coils. CAUSE Replace timer. Valve closed. Check all valves in steam supply and return -- make sure they are open. Remove and clean. Replace if defective. On dryers using solenoid temperature control, check operation of solenoid valve by advancing thermostat. On dryers using solenoid temperature control, thermostat controls operation of solenoid valve. If defective, replace thermostat.
Direct-Spark DIRECT SPARK IGNITION OPERATION Ignition Operation 1. When a call for heat is received from the control supplying 24VAC to the Ignition Control Module, the pre-purge delay timer begins. This delay time allows any air/sediment to be ejected prior to burner ignition. Following the pre-purge delay period, the gas valve is energized and the spark ignitor sparks for the trial ignition period. 2.
DIRECT SPARK IGNITION OPERATION FLOW CHART Page 41
Maintenance—General MAINTENANCE MAINTENANCE 1. CLEAN LINT TRAP DAILY. Remove lint before starting day’s operation. A clean lint trap will increase the efficiency of the dryer, as the moistureladen air will be exhausted more quickly. 2. CLEAN BASKET AND SWEEP SHEETS. Clean periodically and/or as often as required. The basket and sweep sheets are easily accessible by removing the front panel of the dryer. 3. GEAR REDUCER. Maintain the correct oil level.
Maintenance—General MAINTENANCE MAINTENANCE (continued) 6. STEAM HEATED UNITS. Keep steam coils clean. Check periodically and clean often, as required. Remove lint and dirt build-up from fins. Dirty fins decrease the efficiency of steam heated units. 7. GAS BURNERS. Keep burners clean. Check and clean often. 8. GAS PRESSURE. Gas pressure should be checked periodically per specifications on separate page. 9. EXHAUST SYSTEM. Periodically check and clean. 10. VOLTAGE.
Burner Air Inlet Adjustment (with Illustration) BURNER AIR INLET ADJUSTMENT CAUTION Please insure that there is a 1/4” (7 mm) gap between the orifice and burner opening.
Basket Alignment for 150 lb.
Basket Alignment for 150 lb. Dryers INSTRUCTIONS FOR ALIGNING BASKETS ON 150 LB. DRYERS INSTRUCTIONS 1. Loosen bolts number one (1) through five (5). 2. Place pin “A” in position shown in figures 1 and 2. 3. Check pins “B” at position shown in figures 1 and 2 for equal clearance. 4. If pin “B” clearance is unequal, adjust at nut #6. 5. When clearance at pin “B” is correct, tighten bolts #1 in the following order, as viewed from rear of dryer, top right, bottom left, top left and bottom right. 6.
Shimming the Basket and Spider Assembly (Illustration) Page 47
Shimming the Basket and Spider Assembly INSTRUCTIONS FOR SHIMMING THE BASKET AND SPIDER ASSEMBLY This procedure is normally necessary when replacing either the basket or the spider assembly on any dryer. The alignment of these two parts is crucial in assuring a true running basket. A. Align the basket as per instructions on the previous page. B . Rotate the basket to determine where the most outof-round point is (where the basket scrapes or comes closest to scraping the sweep sheet). C.
Air Switch Adjustment AIR SWITCH ADJUSTMENT 1. Shut off current; disconnect leads and remove air switch. 2. Lay air switch assembly on flat surface. Adjust air blade at “A” (figure 1) so that air blade lays flat and surface “B” is parallel to the flat surface. 3.
Dryers with Reversing Control Timer INSTRUCTIONS FOR DRYERS WITH REVERSING CONTROL TIMER Instructions In operation, coasting of basket increases, making it necessary to readjust reversing timer. CAUTION Failure to do this will cause the thermal overload units for the basket to cut-out unnecessarily and probably damage the gear reducer. Adjustment of Reversing Timer Dwell Time CAUTION Dryer power supply must be shut off before adjusting timer.
Dryers with Reversing Control (Illustration) INSTRUCTIONS FOR DRYERS WITHOUT REVERSING CONTROL FAN AND BASKET ROTATION Instructions NOTE Fan rotates counter-clockwise as viewed from back end of motor. See arrow on motor support. Basket rotates counter-clockwise as viewed from back end of motor. See arrow on motor support. Basket rotates counter-clockwise as viewed from front of tumbler. To change rotation of both fan and basket, reverse power leads L1 and L2.
Large Gear Reducer Maintenance LARGE GEAR REDUCER MAINTENANCE LARGE GEAR REDUCER MAINTENANCE Before placing the dryer in operation, check the oil level. If the oil level is correct, it can be checked by removing the fill overflow plug on the right hand side of the gear reducer (facing rear). If oil must be added, remove the vent plug at the top of the gear reducer and add as needed. CHANGE OIL ONCE EVERY 6 MONTHS.
Parts—Front Panel and Door Assembly TU14035 - “C” MODEL 1 2 3 4 5 6 7 8 9 10 11 TU7862 TU7169 TU5503 TUA2319H TU14483 TU2236 TU5288 TU14034 TU2641 PIF172 TU2836 12 TU3212 13 TU3209 Door Glass 20 1/4” Gasket Door Latch Spacer Door Latch with Keeper Door W/A (specify color) Hinge Post (2 each) Door Seal Front Panel (specify color) Thermometer Gasket Hinge Post Bearing (2 each) 5/16” - 32 x 3/8” Hex Screw (2 each) 5/16” I.T.
150 lb.
Parts—150 lb. Dryer (Front of Dryer) 1 TU9422 2 ---3 TU14035 4 5 6 7 8 9 10 11 12 TU6854 RC349 FG140 TU2663 TU2665 TU5801 TU5397 OP251 TU9609 K325 13 TU9444 14 TU9472 TU9607 15 FB187 16 F557 17 TU6159 18 TU490 TU491 19 TU13629 20 K169 21 TU2664 22 TU10345 23 K121 K368 24 TU5911 25 K321 26 TU2881 Jacket Weldment Control Box* “C” Panel and Door Assembly* (specify color) #14 x 3/4” Pan Head Screw 1/4” I.T. Lockwasher Door Switch 1/2” - 20 x 2” Cap Screw 5/8” - 28 x 2” Cap Screw 5/8” I.T.
150 lb.
Parts—150 lb. Dryer (Rear of Dryer) MODELS: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 TUX415 TU4967 TU8206 AT304 TU9663 TU3807 TU14092 TU2363 TU9751 TU6081 TU2007 TU9615 TU470 TU6633 TM200 TU5328 TU4626 TU5658 L50CD42 Air Switch Cover Allen Head Set Screw Air Switch Assembly Square Head Set Screw Gear Sheave (50/60 Hz.) Sheave Bushing Rear Guard Cover Plate “V” Belt 5L500 Motor Sheave—60 Hz. Motor Sheave—50 Hz.
Permanent Press Control Panel Assembly TU13859 - Reversing TU14028 - Non-Reversing 1 2 3 4 5 6 FG147 TU9028 TU12933 TU13620 TUT316 TU7733 7 TU2555 8 ET208 9 TU3805 Toggle Switch (2 each) Push Button Switch Timer (0-15 Minutes) Control Panel Weldment 24V LED Light (3 each) #8 - 18 x 1/2” Self-Drill Screw (8 each) Knob Assembly (2 each) #6 - 32 x 1/4” Binding Head Screw (2 each) Hex Nut (2 each) 1 0 TU13825 TU13974 1 3 FB187 1 4 P104 1 5 TU2842 Nameplate, Reversing, 2-Timer Nameplate.
Moisture Control Panel Assembly TU13967 Reversing 1 2 C196 ET208 3 4 5 6 7 FG147 FG343 FG345 PT118 P104 8 9 10 11 TUT316 TU12932 TU12933 TU13229 12 13 14 TU13345 TU13620 TU13646 TU14031 15 #8-32 x 5/16” Socket Set Screw 6-32 x 1/4” Binding Head Scr. (2 each) Toggle Switch (2 each) Steel Screw Steel Washer M/C Knob 1/4” Brass Washer (Pkg. 6) (2 each) 24V LED Light (4 each) Timer (0-60 Min.) Drying Timer (0-15 Min.
Gas Bonnet and Burner Assembly TU14030 - LP Gas Bonnet TU13836 - Natural Gas Bonnet 1 2 TU14058 CB36 3 4 5 OP267 PT196 RC344 6 7 8 9 10 TUX387 TUX352 TUX435 TU6862 TU13613 GA-00764-0 11 12 13 TU4605 TU4606 TU4934 Gas Manifold 1/4” - 20 x 1/2” Hex Head Screw - 4 each 3/4” x 1/2” Steel Bushing 3/4” Strap 1/4” - 20 x 3/4” Hex Head Screw - 2 each BSI Asm.
Parts—Air Switch Assembly AIR SWITCH ASSEMBLY TU8206 1 2 3 4 5 6 7 8 F888 TU2463 TU3476 TU1771 TU8155 TU1770 TU8171 TU7733 “E” Ring Actuator Arm Air Switch Decal #6 Tinnerman Nut (Pkg. of 12) Air Switch Insulator Air Switch Bracket #8 - 18 x 1/2” Self Drilling Screw (Pkg. of 6) 9 TU3219 #6 x 1” Round Head S.M.S.
Parts—150 lb.
Parts—TM200—Large Gear Reducer with Bronze Teeth 1 2 3 4 5 6 7 8 9 TM203 K474 TM119 TM208 TM225 IB139 TM205 TM204 TM218 Housing Oil Level Plug Kit 1/4” Vent Plug Small Bearing Cone & Cup Worm & Worm Gear 3/8” - 16 x 1 1/4” Cap Screw Small Open End Cap Small Klozure Small Closed End Cap 10 11 12 13 14 15 16 17 VSB134 TU3246 TM217 TM220 TM221 TU5312 TM211 TM212 3/8” Split Lockwasher (Pkg. of 3/8” - 16 x 1” Cap Screw (Pkg.
Reversing Control Panel Assembly (Gas) TU14146 TU14147 TU14198 TU14149 TU14148 TU14199 1 2 3 4 5 6 7 8 Reversing Control Panel 200-240V, 24V Reversing Control Panel 460-480V, 24V Reversing Control Panel 240/415V, 24V Non-Reversing Control Panel 460-480V, Non-Reversing Control Panel 200-240V, Non-Reversing Control Panel 240/415V, TU12874 TU13480 TU13514 F540 TU13516 TU13526 TU14026 TU2793 TU7733 Controls Controls Controls 24V Controls 24V Controls 24V Controls Timer, Solid State Reversing Transformer 200
Reversing Control Panel Assembly (Steam) TU14150 TU14151 TU14197 TU14152 TU14153 TU14196 1 2 3 4 5 6 7 8 Reversing Control Panel 200-240V, 24V Reversing Control Panel 460-480V, 24V Reversing Control Panel 240/415V, 24V Non-Reversing Control Panel 200-240V, Non-Reversing Control Panel 460-480V, Non-Reversing Control Panel 240/415V, TU12874 TU13480 TU13514 F540 TU13516 TU13526 TU14026 TU2793 TU7733 Controls Controls Controls 24V Controls 24V Controls 24V Controls Timer, Solid State Reversing Transformer 2
Parts—Temperature Assembly TU6030—“C” Model—Consists of Ref. No. 1, 2, 3 1 TU5530 2 TU1980 3 TU3593 TU3816 TU8475 TU11193 TU13213 4 TU490 TU491 5 TU3209 6 LB74 Mounting Bracket Thermostat Thermometer Lens Replacement (Texas Gage ONLY) Lens Replacement (Marshaltown Inst. ONLY) Lens Replacement (Weiss—consult factory) Lens Replacement (Weiss—consult factory) Thermostat Knob—Fahrenheit Thermostat Knob—Centigrade #14 x 5/8” S.M.S. (Pkg. of 6) #14 Tinnerman Clip (Pkg.
Page 67
