Member of: OWNER'S MANUAL 50 Lb. Laundry Dryer MODELS GAS L36USS30G L36USD30G L36URD30G L36URS30G STEAM L36URS30S L36URD30S ELECTRIC L36URS30E L36URD30E CISSELL MANUFACTURING COMPANY HEADQUARTERS 831 SOUTH FIRST ST. P.O. BOX 32270 LOUISVILLE, KY 40232-2270 PHONE: (502) 587-1292 SALES FAX: (502) 585-3625 SERVICE/PARTS FAX: (502) 681-1275 THIS MANUAL MUST BE GIVEN TO THE EQUIPMENT OWNER.
IMPORTANT NOTICES—PLEASE READ For optimum efficiency and safety, we recommend that you read the manual before operating the equipment. Store this manual in a file or binder for future reference. WARNING: Purchaser must post the following notice in a prominent location: WARNING: For your safety, the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or death.
WARNING: To avoid fire hazard, do not dry articles containing foam rubber or similar texture materials. Do not put into this dryer flammable items such as baby bed mattresses, throw rugs, undergarments (brassieres, etc.) and other items which use rubber as padding or backing. Rubber easily oxidizes causing excessive heat and possible fire. These items should be air dried. WARNING: Synthetic solvent fumes from drycleaning machines create acids when drawn through the dryer.
ATTENTION: L’ACHETEUR DOIT PLACER L’AVERTISSEMENT SUIVANT DANS UN ENDROIT CLAIR ET VISIBLE: AVERTISSEMENT. Assurez-vous de bien suivre les instructions donnees dans cette notice pour reduire au minimum le risque d’incendie ou d’explosion ou pour eviter tuot dommage materiel, toute blessure ou la mort. __ Ne pas entreposer ni utiliser d’essence ni d’autres vapeurs ou liquides inflammables dans le voisinage de cet appareil ou de tout autre apparell.
CISSELL DRYER WARRANTY The Cissell Manufacturing Company (Cissell) warrants all new equipment (and the original parts thereof) to be free from defects in material or workmanship for a period of two (2) years from the date of sale thereof to an original purchaser for use, except as hereinafter provided.
TABLE OF CONTENTS 50 LB. LAUNDRY DRYER PAGE PAGE Model Numbers & Company Address ......................................... 1 Replacing Bearings Instructions ................................................ 48 Important Notices ...................................................................... 2-4 Basket Alignment .................................................................. 49-50 Dryer Warranty ............................................................................
SYMBOLS The following symbols are used in this manual and/or on the machine.
SYMBOLS Symbol Description rotation in two directions rotation dans les deux sens Drehbewigung in zwei Richtungen movimiento rotativo en los dos sentidos direction of rotation sens de mouvement continu de rotation Drehbewegung in Pfeilrichtung movimiento giratorio o rotatorio en el sentido de la flecha End of Cycle caution attention Achtung atencion; precaucion Page 8
UNPACKING Unpacking/General Installation (All Dryers) Upon arrival of the equipment, any damage in shipment should be reported to the carrier immediately. Upon locating permanent location of a unit, care should be taken in movement and placement of equipment. See outline clearance diagrams for correct dimensions. Remove all packing material such as: tape, manuals, skid, etc Leveling: Use spirit level on top of dryer. Adjust leveling bolts on dryer (see adjustable leveling bolts in maintenance section).
Unpacking/General Installation (All Dryers) GENERAL INFORMATION The dryer is so designed that when an operator opens the dryer door, the basket and exhaust fan stop. You can expect fast drying from a laundry dryer. Hot, dry air is properly and effectively moved through the basket and exhausted through a lint trap to the atmosphere. The dryer comes equipped with an inclined selfcleaning lint screen.
50 lb.
50 lb.
Specifications - 50 lb. Laundry Dryer GENERAL SPECIFICATIONS FOR 50 LB. LAUNDRY DRYERS (STANDARD GAS, STEAM, AND ELECTRIC HEATED MODELS) Basket Load Capacity ...................................... 50 lb (23 kg) Floor Space (Single or Double Motor) .......... 75" (1905 mm) High 37-7/8" (962 mm) Wide 47-1/2" (1206 mm) Deep Basket Size ...................................................... 36" (914 mm) Diameter 30-1/4" (768 mm) Deep Exhaust Duct ...................................................
Specifications - 50 lb. Laundry Dryer GENERAL SPECIFICATIONS FOR GAS FIRED LAUNDRY DRYERS Gas Supply ...................................... 1/2" (DN15) Pipe connection Heat Input* (4 Burners) ................. 130,000 Btu/h (32,759 kcal/h) Natural gas 130,000 Btu/h (32,759 kcal/h) Liquid petroleum gases Drying Time (Approx.) ................... 10 lb (4.5 kg) Dry weight (Indian Head) 100% moisture retention - 10 min. Net Weight (Approx.) ....................
Gas Energy-Saver Laundry Dryer Specifications GAS ENERGY-SAVER DRYER SPECIFICATIONS Basket Capacity ..................................... 50 lb (23 kg) Dry weight Floor Space ........................................... 75" (1905 mm) High 53-1/2" (1359 mm) Deep 37-7/8" (962 mm) Wide Basket Size ............................................ 36" (914 mm) Diameter 30" (762 mm) Deep Exhaust Duct* ....................................... 6" (152 mm) Diameter Exhaust Air Pressure ............................. Max.
Steam Heated Specifications GENERAL SPECIFICATIONS FOR STEAM HEATED LAUNDRY DRYERS Maximum Air Displacement ................. 800 cfm (1359 m³/h) Recommended Operating ..................... 630-730 cfm Range (1070 - 1240 m³/h) Steam Supply Connection .................... 3/4" (DN20) Steam Return Connection .................... 3/4" (DN20) Operating Steam Pressure ................... Low pressure - 7-15 psi (0.5 - 1 Bar) Maximum high pressure100 psi (6.9 Bar) Drying Time (Approx.) ........................
Motor Number List for 50 lb. Double and Single Motor Models MOTOR NUMBER LIST FOR 50 LB. DOUBLE MOTOR MODELS Motor No. Voltage Hz. Phase HP KWATTS Amps Basket/Fan MTR300 115/200-240 60 1 1/2 .373 6.2/3.1 B MTR302 200-240/480 60 3 1/2 .373 1.8/.9 B MTR300 110/200-230 50 1 1/2 .373 7.4/3.7 B MTR302 240/415 50 3 1/2 .373 2.0/1.0 B MTR101 575 60 3 1 .75 1.7 B MTR302 220/380 50 3 1/2 .373 2.0/1.0 B MTR302 220/380 60 3 1/2 .373 1.8/.
Electrical Connections - All Dryers ELECTRICAL CONNECTIONS Dryers must be electrically grounded by a separate #14 or larger green wire from the grounding terminal within the service connection box, to a cold water pipe. In all cases, the grounding method must comply with local electrical code requirements; or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or the Canadian Electrical Code, CA C22.1. See wiring diagram furnished with dryer.
Gas Piping Installation GAS PIPING INSTALLATION 1. The installation must conform with local codes, or in the absence of local codes with the National Fuel Gas Code, ANSI Z223.1 or the CAN/CGA-B149, Installation Codes. 2. Check identification nameplate for type of gas for dryer. 3. Check the altitude of dryer. 4. Check with utilities company for proper gas pressure and gas supply line. 5. Natural gas only—check the gas pressure inlet supply to dryer, 11 inches water column maximum. Manifold pressure—3.
Gas Piping Installation (Illustrations) Gas shutoff valve is not supplied with dryer. The dryer and it’s individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5 kPa). The dryer must be isolated from the gas supply piping system by closing it's individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psi (3.5 kPa).
Gas Service Installation Instructions GAS SERVICE INSTALLATION INSTRUCTIONS The size of the gas service pipe is dependant upon many variables, such as tees, lengths, etc. Specific pipe size should be obtained from the gas supplier. Refer to the “Gas Pipe Size” chart in this manual for general gas pipe size information.
Gas Pipe Size Chart TOTAL BTU/HR (for LP Gas correct total BTU/HR below by multiplying by .6) GAS PIPE SIZE FOR 1000 BTU (250 KCAL) NATURAL GAS AT 7” (17.8 CM) W.C. PRESSURE TOTAL KCAL In figuring total length of pipe, make allowance for tees and elbows. (50 ft.) (75 ft.) (100 ft.) (125 ft.) 15,24 m 22,86 m 30,48 m 38,1 m HOUR (25 ft.
Steam Piping - Installation Insatructions STEAM PIPINGINSTALLATION INSTRUCTIONS PIPING RECOMMENDATIONS 1. Set and anchor dryer in position. Machine should be level to assure proper steam circulation. 2. To prevent condensate draining from headers to dryer, piping should have a minimum 12" (305 mm) above respective header. Do not make steam connection to header with a horizontal or downwardly facing tee or elbow. 3.
Steam Piping Installation (Illustration) Page 24
Dryer Installation With Multiple Exhaust For Exhaust Duct less than 14 feet (5 m) and 2 elbows equivalent and less than 0.3 inches (8 mm) static pressure. DRYER EXHAUSTS Area of section “A-A” must be equal to the sum of dryer exhaust pipes entering multiple exhaust pipe. (See chart below.
Dryer Installation with Multiple Exhaust DRYER INSTALLATION WITH MULTIPLE EXHAUST For Exhaust Duct more than 14 feet (5 m) and 2 elbows equivalent and more than 0.3 inches (8 mm) static pressure. (See illustration on next page.) 1. 2. 3. 4. 5. 6. 7. Make-up air from outside building may enter enclosure from top or side walls. (See Dryer Make-Up Air Requirements Chart) Use constant diameter duct with area equal to the sum of dryer duct areas. EXAMPLE: 6-8 inch (203 mm) diameter duct = 1-19.
Suggested Minimum Dryer Make-up Air Requirements Dryer Model Dryer Pocket Capacity C 30 C 30 E/S C 30 ST C 50 C 50 E/S C 75 C 75 E/S C 75 ST HD80 C 110 C 110 E/S C 125 C 150 HD175 HD190 HD20 HD30 HD50 HD75 lb 30 30 30 50 50 75 75 75 80 110 110 125 150 175 190 9.1 13.6 22.7 34 20 30 50 75 kg 13.6 13.6 13.6 22.7 22.7 34 34 34 36.3 50 50 56.7 68 79.4 86.
Dryer Installation With Separate Exhaust (Preferred) DRYER INSTALLATION WITH SEPARATE EXHAUST (PREFERRED) For ductwork less than 14 feet (5 m) and 2 elbows equivalent and less than 0.3 inches (8 mm) static pressure: NEVER exhaust the dryer into a chimney. NEVER install wire mesh screen over the exhaust or make-up air area. NEVER exhaust into a wall, ceiling, or concealed space. 1. 2. 3. 4. Make-up air opening from outside the building may enter the enclosure from the top or side walls.
Exhaust and Venting DRYER AIR FLOW INSTALLATION Nothing is more important than air flow for the proper operation of a clothes dryer. A dryer is a pump which draws make-up air from the out-of-doors, through the heater, through the clothes and then forces the air through the exhaust duct back to the out-of-doors. Just as in a fluid water pump, there must be a fluid air flow to the inlet of the dryer, if there is to be the proper fluid air flow out of the exhaust duct.
Rules for Safe Operation of Dryer RULES FOR SAFE OPERATION OF DRYER 1. 2. 3. 4. 5. 6. 7. 8. 9. ENERGY-SAVING TIPS 1. 2. 3. 4. 5. 6. Be sure your dryer is installed properly in accordance with the recommended instructions. CAUTION Be safe—shut main electrical power supply and gas supply off externally before attempting service. CAUTION Never use drycleaning solvents: gasoline, kerosene, or other flammable liquids in the dryer. Fire and explosion will occur.
Operating Instructions—Coin Meter Models OPERATING INSTRUCTIONS—COIN METER MODELS OPERATING INSTRUCTIONS—COIN METER MODELS 1. After loading the dryer with water washed clothes, close the loading door. 2. ELECTRO-MECHANICAL COIN METER: Insert proper coin(s) in slot and turn knob until it stops. COMPUTERIZED COIN METER: Insert coin. Amount of drying time will appear on the digital display. Maximum time is 99 minutes. Additional coins may be vended any time during the cycle. 3.
Operating Instructions—Coin Meter Models IMPORTANT IMPORTANT If the tumbler door is opened during the drying cycle, the fan and heat will shut off. Press “START” button to resume the cycle. This dryer is designed for a capacity maximum load. Overloading it will result in longer drying time and damp spots on some of the load. Maximum operating efficiency depends on proper air flow. The lint screen must be kept clean daily to insure proper circulation of air throughout the dryer.
Setting Time On Computerized Coin Meter (Illustration) INSTRUCTIONS FOR SETTING TIME ON “COMPUTERIZED COIN METER” DIP Switch Banks are located here Page 33
Setting Time On Computerized Coin Meter INSTRUCTIONS FOR SETTING TIME ON COMPUTERIZED COIN METER 1. This dryer is equipped with two banks of four DIP switches each. 2. Each DIP switch bank consists of 4 small switches each with a specified amount of time (minutes), as shown: ON OFF 1 min. 2 min. 4 min. 8 min. 3. To set the time on the DIP bank simply set the appropriate switch to the ON (up) position to total the desired amount of time. NOTE OFF (down) position equals 0 minute.
Operating Instructions—Double Timer Models OPERATING INSTRUCTIONS DOUBLE TIMER MODELS OPERATING INSTRUCTIONS—DOUBLE TIMER MODELS Step 1. After loading the dryer with water washed clothes, close the loading door. Step 2. Turn the 60 minute drying (heat) timer to the desired time. The drying cycle light will be on. Step 3. Turn the 15 minute cooling (air) to the desired time. The cooling light will come on after the drying finishes. Step 4.
Double Timer Models (Illustration) Double Timer Panel Page 36
Service Savers TROUBLESHOOTING To help you troubleshoot the dryer, listed below are the most common reasons for service calls and some answers to the problems. Before you call service, please review the following items: DRYER WON’T START DRYER WON’T START 1. Is the door completely closed? 2. Are the controls set to the “on” position? 3. Did you push the “start” control? 4. Has a fuse blown or a circuit breaker tripped? 5. Are the fuses tight? 6. Check for low voltage. 7.
Troubleshooting Chart TROUBLE Motor will not start. CAUSE No power. Incorrect power. Motor tripping on thermal overload. Time off. Loose wiring connections. Defective starting relay. Low voltage. Inadequate wiring. Loose connections. Inadequate air. Basket motor will not run. Poor housekeeping. Loading door open. Door switch out of adjustment. Dryer does not stop at end of time period. Motor runs, but basket will not revolve. Defective door switch. Defective basket motor contractor.
Troubleshooting Chart TROUBLE Dryer noisy or vibrating. CAUSE Not leveled. Fan out of balance. Basket rubbing. V-belt sheaves. Belt. Foreign objects. Dryer runs, but no heat. Incorrect voltage. No voltage. Defective gas valve. gas turned off. Defective door switch. Air switch not operating. REMEDY Check manual for proper leveling procedures. Accidental damage to the fan blade can change the dynamic balance. Damaged fans should be replaced. Adjust basket clearance. Tighten set screws.
Troubleshooting Chart TROUBLE Dryer runs, but no heat. (continued) CAUSE Air switch out of adjustment. Air switch defective. Gas pressure too low. Improper orifice. Main burners burning improperly. Low or high gas flame. Dryer too hot. Direct spark ignition module defective. Electric power to heating unit turned off. Line fuse or heater circuit fuse blown to unit. Defective relay. Defective electric elements. Defective thermostat. Defective safety overload thermostat. Lint compartment door open.
Troubleshooting Chart TROUBLE Dryer does not stop at end of time period (6). Dryer runs no steam to coils. CAUSE Defective timer. Replace timer. Valve closed. Check all valves in steam supply and return. Make sure they are open. Remove and clean. Replace if defective. On dryers using solenoid temperature control, thermostat controls operation of solenoid valve by advancing thermostat. On dryers using solenoid temperature control, thermostat controls operation of solenoid valve.
Direct-Spark Ignition Operation DIRECT SPARK IGNITION OPERATION NOTE: Some models are equipped with a dual ignition system. The dual ignition system contains two direct spark ignition modules in parallel. Each module has its own flame sense circuit and acts independently of the other. If either bonnet limit thermostat opens because of high heat or flame impingement, the entire ignition system will shut down. 1.
DIRECT SPARK IGNITION OPERATION FLOW CHART Page 43
General Maintenance GENERAL MAINTENANCE 1. Clean lint trap daily. Remove lint before or after each day of operation. A clean lint trap will increase the efficiency of the dryer and the moisture-laden air will be exhausted outside more quickly. 2. Keep basket and sweep sheets clean. Clean as often as needed. The basket and sweep sheets are accessible by removing the front panel of the dryer. 3. Gas burners, steam coils, electric coils. Check and clean often. 4. Pulleys and belts.
General Maintenance GENERAL MAINTENANCE (continued) 7. Periodically clean and examine exhaust system. 8. Keep dryer area clean and free of gasoline, combustible materials and other flammable liquids or vapors. 9. Do not obstruct the flow of combustion (make-up) air and ventilating air. 10. Check gas pressure periodically. 11. Gas burner air inlet shutters can be adjusted for proper flame by following instructions outlined on separate page of this manual. 12. Main Basket Bearings.
Burner Air Inlet Shutter Adjustment (w/Illustrations) BURNER AIR INLET SHUTTER ADJUSTMENT Burner air inlet shutters are correctly adjusted when the flame is primarily blue. Type of Gas Burner Air Inlet Shutter Adjustment Natural gas Liquid petroleum Manufactured gas AIR SHUTTER ADJUSTMENT Wide open 1/2 Open 1/8 Open Air Shutter Adjustment Proper method Close air shutters to yellow tip, then open air shutters to blue flame tip. Orange tips are impurities in the air such as lint, dust, etc.
Burner Air Inlet Shutter Adjustment NEED TO ADJUST SHUTTER Need to Adjust Shutter Burners air inlet shutters are adjusted insufficient; air is admitted through the burner. Flame pattern is straight up and flame is yellow. WRONG--NEED TO ADJUST SHUTTER NEED TO PROVIDE CORRECT AIR FLOW THROUGH THE DRYER Need to Provide Correct Airflow Through the Dryer This flame pattern indicates the burner air inlet shutters are correctly adjusted, but air through the dryer is insufficient.
Replacing Bearings and Collars Instructions Operating Conditions Clean Dirty Moisture REPLACING BEARINGS AND COLLARS INSTRUCTIONS Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Grease Intervals Every 6 months Every month Every week Remove belt guard, V-belt, spacer and basket sheave. Loosen set screws on the flange bearing and on the pillow block bearing. Remove the bolts holding the pillow block bearing and take it off the shaft.
Basket Alignment—Double Motor Model BASKET ALIGNMENT DOUBLE MOTOR MODEL Step 1 Loosen the 4 gear reducer mounting bolts (1, 2, 3, & 4) on rear of dryer, and 2 adjusting bolts #5, on gear reducer housing. (figure 3) Step 2 Place one “A” and two “B” diameter pins inside the drying compartment between the rim of the basket opening and the rim of the door opening, in the positions shown in figure 1 and figure 2. Check the two “B” pins for equal clearance.
Basket Alignment—Single Motor Model BASKET ALIGNMENT SINGLE MOTOR MODEL Step 1 Loosen the set screws on the flange and pillow block bearings. Step 2 Loosen the 4 side bolts, “1, 2, 3, 4,” on the basket bearing bracket. (see figure 3) Loosen the two adjusting bolts and locknuts “5, 6,” inside the bracket. And loosen the bolts “7,” on the pillow block bearing.
Basket Shimming Instructions BASKET SHIMMING INSTRUCTIONS This procedure is normally necessary when replacing either the basket or the spider assembly on any dryer. Proper shimming is crucial to obtain a true running basket. A. Align the basket as per instructions in the manual. B. Rotate the basket to determine where the most out-of-round point is (where the basket scrapes or comes closest to scraping the sweep sheet). C. Mark this position and the nearest rib to this position. D.
Air Switch Adjustment (with Illustration) AIR SWITCH ADJUSTMENT 1. Shut off current; disconnect leads and remove air switch. 2. Lay air switch assembly on flat surface. Adjust air blade at “A” (figure 1), so that air blade lays flat and surface “B” is parallel to the flat surface. 3.
Gear Reducer Information OPERATION AND MAINTENANCE OPERATION AND MAINTENANCE After Start Up The Gear reducer is shipped filled with oil to the right level and after two weeks or 100 hours of operation, drain the oil, and flush the gear reducer with a light flushing oil. The original oil can be used for re-filling if it has been filtered; otherwise, new oil must be used. After this, change the oil every six months or 2500 hours of operation. CAUTION • .
Parts—Duct Work and Air Switch Assembly—TU8206 (with Illustrations) Duct Work Parts 1 2 3 5 6 7 TU8053 TU8055 TU8052 TU7375 TU8177 TU9161 Duct Elbow Duct Long Duct Tee Extended Elbow Duct Short Installation Label Air Switch Assembly TU8206 1 2 3 4 5 6 7 8 9 F888 TU2463 TU3476 TU1771 TU8155 TU1770 TU8171 TU7733 TU3219 “E” Ring Actuator Arm Air Switch Decal #6 Tinnerman Nut Air Switch Insulator Air Switch Bracket #8 - 18 x 1/2" Self Drilling Screw #6 x 1" Round Head S.M.S.
Dryers with Reversing Control Timer INSTRUCTIONS FOR DRYERS WITH REVERSING CONTROL TIMER Instruction In operation, coasting of basket increases, making it necessary to readjust reversing timer. CAUTION Failure to do this will cause the thermal overload units for the basket to cut-out unnecessarily and probably damage the gear reducer. Adjustment of reversing timer dwell time CAUTION Dryer power supply must be shut off before adjusting timer.
Dryers with Reversing Control Timer (Illustration) INSTRUCTIONS FOR DRYERS WITHOUT REVERSING CONTROL FAN AND BASKET ROTATION Instructions NOTE: Fan rotates counter-clockwise as viewed from back end of motor. See arrow on motor support. Basket rotates counter-clockwise as viewed from back end of motor. See arrow on motor support. Basket rotates counter-clockwise as viewed from front of tumbler. To change rotation of both fan and basket, reverse power leads L1 and L2.
Parts—Front Panel and Door Assembly TU5810 Front Panel and Door Assembly (Coin Vault) (Specify Color) TU6056 Front Panel and Door Assembly (Time and Temperature) (Specify Color) TU7627 Front Panel and Door Assembly (Time and Temperature) with Thermometer 1 TU10784 1a 2 3 4 5 6 7 8 9 10 11 Front Panel (for Coin Vault) (Specify Color) TU10785 Front Panel (for Time and Temp.
50 lb.
Parts—50 lb.
50 lb.
50 lb.
50 lb.
50 lb. Laundry Dryer - Double Motor Model - Rear View 1 TU11660 Jacket (Coin Meter Model) TU9594 Jacket (Timer Model) 2 TU2372 Bushing 3 SB170 Junction Box Cover 6 TU5890 Control Box Cover 26 TU2476 Felt Seal 7 TU3857 Belt Guard Cover 27 TU4684 Key 8 TU2317 V-Belt 46-380 - 50/60 Hz. 28 TU5874 Fan Wheel with Set Screws 9 TU6722 Gear Sheave (AK-51H) with 24 25 TU2473 60 Hz.
Bearings and Related Parts (with Illustration) 1 2 3 4 5 6 7 8 9 10 11 TU13147 OP233 TU2831 TU2883 TU10850 TU2195 TU10676 OP251 RC347 TU13372 TU10644 Bearing Support Bracket 1/2" Hex Nut (pkg 6) 1/2" Lockwasher (pkg 6) 1/2" Flat Washer (pkg 6) Flange Bearing 1/2" - 13 x 1-3/4" Cap Screw (pkg 6) Pillow Block Bearing 1/2" I.T.
Parts—Small Gear Reducer—TM100 Quantity 1 2 3 4 6 7 8 9 11 12 13 14 15 16 17 TM103 TM104 TM105 TM108 TM101 TM110 TM112 TM115 TM102 TM120 TU2623 TU2839 TM121 RC349 TM118 TU3465 Housing Small Seal Small Open End Cap Small Bearing Cup & Cone Worm 1-1/2" x 7-1/8" Large Bearing Cup & Cone Large End Cap 1/4" Pipe Plug Worm Gear Oil Seal Cap Screw 3/8" - 16 x 1-1/"” Cap Screw 1/4" - 20 x 7/8" Vent Plug 1/4" NPT 1/4” Internal Tooth Lockwasher Small Closed End Cap Transmission oil (Not Shown) Page 65 1 1 1 2 1
Control Panel and Access Door—Two Timer Model Access Door Assembly Ref. Nos. 1,2,4,5,20,26 TU13887 (Specify Color) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 TU13939 TU8013 TU3400 TU4822 TU2844 TU11510 TUT191A TU13942 TU12932 TU12933 FG147 TU1771 TU13856 M271 Access Door W/A (Specify Color) Cissell Nameplate Nut Lock #3186 Key JWC2 Push Button Switch Push Button Switch Plate Spacer Timer, 24V, 0-60 Minutes Timer, 24V, 0-15 Minutes Toggle Switch Twin Nut (Pkg 12) Control Panel Plate Asm. #8 Int.
Control Panel and Access Door—Coin Meter Model Access Door Assembly Ref. Nos. 1,5-7, 18, 20 TU11666 (Specify Color) Control Panel Assembly Ref. Nos. 9-17, 22-25 TU13721 - 24V 50/60 Hz. Gas TU13847 - 24V 50/60 Hz.
Reversing Control Box Assembly 1 2 3 4 5 6 7 8 9 10 11 TU9374 TU13700 RC344 TU7733 TU13480 TU13516 TU13526 TU2793 TU14118 F540 TU12874 Reversing Control Box W/A Control Panel Plate 1/4" - 20 x 3/4" Hex Head Screw #8 - 18 x 1/2" Self Drill Screw (Pkg 6) Transformer, 200-240V/24V w/Reset Contactor, 24V Contactor Assembly, 24V Reversing #8 - 18 x 3/4" Self Drill Screw (Pkg 6) Box Cover Plate #6 x 5/8" Phillips Head Screw Timer, Solid State Reversing Page 68
Parts—Thermostat Assembly (Coin Meter and Double Timer Models) TU9111 1 2 3 4 5 6 7 8 9 TU3240H TU3240H TU5150H TU7244H TU5143 TU3624 TU3400 TU7733 TU6067 Safety High Limit Thermostat 185°F Thermostat 150°F Thermostat 135°F Thermostat Mounting Bracket #6-32 x 1/4" Round Head Screw (6 each) #6-32 Hex Nut #8 x 1/2" Self Drill Screw #8 Speed Clip (2 each) Page 69
Parts—Standard Gas Bonnet GAS BONNET ASSEMBLY - TU13675 (Natural Gas) DSI GAS BONNET ASSEMBLY - TU13716 (LP Gas) DSI 1 TU8683 2 TU7733 3 4 5 6 7 8 9 10 GA-00764-0 TU13212 TU2226 TU13826 OP291 C1365 TU13678 TU13523 TU13513 11 CB36 Bonnet #8 - 18 x 1/2" Self Drill Screw (Pkg. of 6) Electrode Spark Igniter 1/2" Pipe Nipple 24" Manifold Mounting Bracket Electrode Spark Mounting Bracket 1/2" Elbow (Street) Connector T & B Thermostat, Man.
Parts—Energy-Saver Gas Bonnet ENERGY-SAVER GAS BONNET - TU13787 (Natural Gas) ENERGY-SAVER GAS BONNET - TU13788 (LP Gas) 1 1A 1B 2 3 4 5 6 7 8 9 10 11 13 14 15 16 17 18 19 20 TU8697 TU8561 TU7787 TU7733 TU2842 TU13212 TU2226 TU7294 GA-00764-0 TU13826 C1365 TU8690 TU7373 TU7733 CB36 TU2846 TU2847 TU4934 TU2224 TU3539 TU7840 “F” Bonnet Front Plate Hinge Top Panel #8 x 1/2" Self Drill Screw (Pkg.
Steam Heating Unit - Nine Section (Illustration) TU13689—9 Section Steam Bonnet Assembly w/Solenoid Valve 24V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 TU2546 TU2547 TU2548 TU2413 TU2414 TU2405 CB36 TU7733 TU2598 TU2735 TU4608 TU13517 CFB2100 TU4790 TU10651 Housing Weldment Front Coil Retainer Rear Coil Retainer Steam Coil Manifold 3/4" - 16 x 3/8" Straight Connector Steam Coil (9 required) 7 3/4" W x 1 5/8" H x 26" L #1/4 - 20 x 1/2" Hex Head Screw (Pkg. of 6) #8 x 1/2" S.M.S. (Pkg.
Electric Heating Unit (Illustration) 1 2 3 4 5 7 8 9 10 11 12 13 TU3103 TU3102 TU9205 TU9207 TU12454 TU3104 TU3767 TU3768 TU3253 TU7244H TU7738 TU9254 14 TU9258 15 CB36 Bonnet Weldment Hold Down Plate Control Box Weldment Terminal Box Cover Top Cover Air Inlet Cover Contact Strap (4 required) Contact Strap (1 required) Insulators Thermostat 135o F Grounding Lug High Voltage Label for 415V Only Ground Label 1/4"-20 x 1/2" Hex Screw (Pkg.
50 lb.
Electric Heating Citcuit - 50 Lb.
Page 76
