Installation guide

18 Release Notes for Catalyst 6000 Family Software Release 5.x

Open and Resolved Caveats in Software Release 5.3(3)CSX

• When using TACACS+, if you open a telnet session to the switch and enter a username and close

the telnet session without entering a password, the TACACS+ session from the switch to the

TACACS+ server remains open. This problem is resolved in software release 5.3(3)CSX.

(CSCdp02341)

• Avoid using Ctrl-C after entering the conﬁgure network command. Using Ctrl-C results in a

command half completed which leaves the switch in an unknown state for that feature. This

problem is resolved in software release 5.3(3)CSX. (CSCdm27473)

• The switch has been booted with a conﬁguration that includes a QoS IP ACL. You then disable

QoS, but when you issue a set qos bridged-microﬂow-policing command, the command

completes without warning that QoS is disabled. This problem seems to only occur if the bridged

packet microﬂow feature is already enabled.

A second problem is when you issue a show qos acl info command; the ACL is displayed without

a warning that QoS is disabled. This problem is resolved in software release 5.3(3)CSX.

(CSCdm85903)

• SNMP traps might not be properly generated. This problem is resolved in software release

5.3(3)CSX. (CSCdm76987)

• A system reset might occur when traces are enabled and you attempt to do a TFTP activity such

as downloading a conﬁguration. This problem is resolved in software release 5.3(3)CSX.

(CSCdm83928)

• A system reset might occur upon receiving invalid PVSTs and BPDU's on an EtherChannel. This

problem is resolved in software release 5.3(3)CSX. (CSCdp07549)

• Packets are still classiﬁed with old DSCP value after the ACL has been updated. This problem is

resolved in software release 5.3(3)CSX. (CSCdp10614)

• The system might reset when you try to set objects in ciscoFlashPartitioningTable. This problem

has been ﬁxed by not supporting this Table. This problem is resolved in software release

5.3(3)CSX. (CSCdp11615)

• SNMP: After you set rowStatus of an eventEntry to under_creation, any set/get the eventEntry

might reset the system. This problem is resolved in software release 5.3(3)CSX. (CSCdp13317)

• Occasionally after system power up, display shows minor hardware problem for modules. This

problem is resolved in software release 5.3(3)CSX. (CSCdp11646)

• After entering a set boot conﬁg-register ignore-conﬁg and resetting the switch, the switch

comes back up and attempts to use BOOTP to obtain an IP address. When the BOOTP sending

messages are printed to the console, they are followed by a message: bootp_send: sendto 51. This

message indicates that the BOOTP send is failing. This problem is resolved in software release

5.3(3)CSX. (CSCdp19611)

• If you change port speed from 100Mbps to 10Mbps and then back to 100Mbps, port trafﬁc might

stop until you reset the module. This problem is resolved in software release 5.3(3)CSX.

(CSCdp11730)

• A VTP client and a VTP server in the same VTP domain are separated by a VTP transparent

mode switch that is not a member of any VTP domain. When the VTP client is reset, the client

does not update its conﬁguration after receiving a VTP update from the VTP server. This problem

is resolved in software release 5.3(3)CSX. (CSCdp05027)

• VTP notiﬁcations are sent on wrong SCP SAP address for the ATM module. This problem is

resolved in software release 5.3(3)CSX. (CSCdp24165)