Specifications
4 48 10/100BaseTX (RJ45)V
WS-X4148-RJ45V
JAE060800BL
M MAC addresses Hw Fw Sw
Status
--+--------------------------------+---+------------+----------------+---------
1 0009.e845.6300 to 0009.e845.6301 0.4
Ok
2 0009.e845.6302 to 0009.e845.6303 0.4 12.1(12r)EW( 12.1(12c)EW, EAR
Ok
3 0001.6443.dd20 to 0001.6443.dd4f 0.0
Ok
4 0008.2138.d900 to 0008.2138.d92f 1.6
Ok
show diagnostics online module
The
show diagnostics online module
slot #
command provides results of diagnostic tests for the module in slots 3 through 7. You perform the diagnostic test, which is available only for the active Supervisor Engine, with the issue of the
show
diagnostics power-on
command.
4507#
show diagnostics online module 3
Slot Ports Card Type Diag Status Diag Details
---- ----- -------------------------------------- ---------------- ------------
3 48 10/100/1000BaseTX (RJ45)
Passed
None
Detailed Status
---------------
. = Pass U = Unknown
L = Loopback failure S = Stub failure
I = Ilc failure P = Port failure
E = SEEPROM failure G = GBIC integrity check failure
Ports 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
. . . . . . . . . . . . . . . .
Ports 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
. . . . . . . . . . . . . . . .
Ports 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
. . . . . . . . . . . . . . . .
show diagnostics power-on
The
show diagnostics power-on
command provides POST results for the active Supervisor Engine. Currently, with Route Processor Redundancy (RPR), the results of the standby Supervisor Engine are not available.
4507#
show diagnostics power-on
Power-On-Self-Test Results
Power-on-self-test for Module 2: WS-X4515
Traffic using serdes loopback (L2; all ports at once)...
switch port 0: . switch port 1: . switch port 2: .
switch port 3: . switch port 4: . switch port 5: .
switch port 6: . switch port 7: . switch port 8: .
switch port 9: . switch port 10: . switch port 11: .
switch port 12: . switch port 13: . switch port 14: .
switch port 15: . switch port 16: . switch port 17: .
switch port 18: . switch port 19: . switch port 20: .
switch port 21: . switch port 22: . switch port 23: .
switch port 24: . switch port 25: . switch port 26: .
switch port 27: . switch port 28: . switch port 29: .
switch port 30: . switch port 31: .
Traffic using asic loopback (L2; all ports at once)...
switch port 0: . switch port 1: . switch port 2: .
switch port 3: . switch port 4: . switch port 5: .
switch port 6: . switch port 7: . switch port 8: .
switch port 9: . switch port 10: . switch port 11: .
switch port 12: . switch port 13: . switch port 14: .
switch port 15: . switch port 16: . switch port 17: .
switch port 18: . switch port 19: . switch port 20: .
switch port 21: . switch port 22: . switch port 23: .
switch port 24: . switch port 25: . switch port 26: .
switch port 27: . switch port 28: . switch port 29: .
switch port 30: . switch port 31: .
Traffic using asic loopback (L3; all ports at once)...
switch port 0: . switch port 1: . switch port 2: .
switch port 3: . switch port 4: . switch port 5: .
switch port 6: . switch port 7: . switch port 8: .
switch port 9: . switch port 10: . switch port 11: .
switch port 12: . switch port 13: . switch port 14: .
switch port 15: . switch port 16: . switch port 17: .
switch port 18: . switch port 19: . switch port 20: .
switch port 21: . switch port 22: . switch port 23: .
switch port 24: . switch port 25: . switch port 26: .
switch port 27: . switch port 28: . switch port 29: .
switch port 30: . switch port 31: .
Module 2 Passed
Note:
In this sample output, the Supervisor Engine in slot 2 is in active mode, and slot 1 is in standby mode.
show power
The
show power
command provides information about the power supplies that you have installed in the system. The command also gives information about the available power and the status of power supplies.
4507#
show power
Power Fan Inline
Supply Model No Type
Status
Sensor Status
------ ---------------- --------- ----------- ------ ------
PS1 PWR-C45-2800AC AC 2800W good good good
PS2 PWR-C45-1000AC AC 1000W err-disable good n.a.
*** Power Supplies of different type have been detected***
Power Supply Max Min Max Min Absolute
(Nos in Watts) Inline Inline System System Maximum
-------------- ------ ------ ------ ------ --------
PS1 1400 1400 1360 1360 2800
PS2 0 0 0 0 0
Power Summary
(in Watts) Available Used Remaining
------------- --------- ------ ---------
System Power 1360 450 910
Inline Power 1400 18 1382
Maximum Power 2800 468 2332
Power supplies needed by system : 1
Power Used Power Used
Mod Model (online) (in Reset)
---- ----------------- ---------- ----------
1 WS-X4515 110 110
2 WS-X4515 110 110
3 WS-X4448-GB-RJ45 120 72
4 WS-X4148-RJ45V 60 50
Note:
In this sample output, the second power supply is in
err-disable
mode because there is no allowance for the mix of different types of power supplies.
show environment status
The
show environment status
command provides information about the status of the power supplies, the Supervisor Engine module, and the fan tray.
Switch#
show environment status
Power Fan
Supply Model No Type
Status
Sensor
------ --------------- --------- ----------- ------
PS1 PWR-C45-1400AC AC 1400W
good good
PS2 PWR-C45-1400AC AC 1400W
good good
Power Supply Max Min Max Min Absolute
(Nos in Watts) Inline Inline System System Maximum
-------------- ------ ------ ------ ------ --------
PS1 0 0 1360 1360 1400
PS2 0 0 1360 1360 1400
Power supplies needed by system : 1
Chassis Type : WS-C4506
Supervisor Led Color : Green
Fantray : good
Power consumed by Fantray : 50 Watts
show interface interface-id status
The
show interface
interface-id
status
command gives the status of the interface, which is one of these statuses:
z
connected
z
notconnect
z
disabled