Specifications

ManualsBrandsCisco ManualsComputer equipmentWS-X4013 - Supervisor Engine II-Plus-TS

Corporate Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Installation and Configuration Note for the

Catalyst 4500SeriesSupervisor Engine II-PlusTS

Product Numbers: WS-X4013+TS = Catalyst 4500 Series Supervisor Engine II-Plus TS

This publication describes how to install and verify the operation of the Catalyst 4500 series switch

Supervisor Engine II-Plus TS. Refer to the software configuration guide for your switch to obtain

configuration information for the supervisor engines and switching modules.

Contents

This document contains these sections:

• Safety Overview, page 2

• Supervisor Engine II-Plus TS, page 7

• Port Cabling Specifications, page 10

• Installing and Removing the Supervisor Engine, page 11

• Attaching Module Interface Cables, page 15

• Configuring Your Supervisor Engine, page 16

• SFP Guidelines, page 16

• Standards Compliance Specifications, page 20

• Related Documentation, page 20

• Obtaining Documentation, page 21

• Obtaining Technical Assistance, page 22

• Obtaining Additional Publications and Information, page 23

Summary of content (24 pages)

PAGE 1
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS Product Numbers: WS-X4013+TS = Catalyst 4500 Series Supervisor Engine II-Plus TS This publication describes how to install and verify the operation of the Catalyst 4500 series switch Supervisor Engine II-Plus TS. Refer to the software configuration guide for your switch to obtain configuration information for the supervisor engines and switching modules.
PAGE 2
Safety Overview Safety Overview Throughout this publication, safety warnings appear in procedures that may harm you if performed incorrectly. A warning symbol precedes each warning statement. Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.
PAGE 3
Safety Overview Warnung WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
PAGE 4
Safety Overview Varning! VIKTIGA SÄKERHETSANVISNINGAR Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.
PAGE 5
Safety Overview Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
PAGE 6
Safety Overview Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine II-Plus TS 6 78-16551-01
PAGE 7
Supervisor Engine II-Plus TS Supervisor Engine II-Plus TS This section describes the Catalyst 4500 series Supervisor Engine II-Plus TS (WS-X4013+ TS). This supervisor engine provides data path and data control for all network interfaces, and also provides 12 10/100/1000BASE-T IEEE 802.3af compliant Power over Ethernet (PoE) ports and 8 1000BASE-X SFP ports.
PAGE 8
Supervisor Engine II-Plus TS Figure 1 Catalyst 4500 Series Supervisor Engine II-Plus TS (WS-X4013+TS) RESET button Switch load indicators Compact Flash port Ethernet management port CONSOLE port 113860 STATUS LED PoE status LED The supervisor engine includes interfaces for SNMP, console, and Telnet and provides management functions such as environmental status monitoring. There is a total of 158.4 Watts available for PoE. This allows any eight ports to be compliant to IEEE 802.3af with 15.
PAGE 9
Supervisor Engine II-Plus TS LEDs Table 1 describes the LEDs on the supervisor engine front panel. Table 1 Supervisor Engine LEDs (WS-X4013+TS) LED LED Status STATUS UTILIZATION Indicates the results of a series of self-tests. Green All diagnostic tests passed. Red A test failed. Orange System boot or diagnostic test is in progress. Off Module is disabled.
PAGE 10
Port Cabling Specifications Console Port The Catalyst 4500 series Supervisor Engine II-Plus TS console port has an EIA/TIA-232 RJ-45 connector.
PAGE 11
Installing and Removing the Supervisor Engine Maximum Cable Distances Table 3 shows the maximum cable distances for transceiver speed and cable type. Table 3 Maximum Cable Distances Transceiver Speed Cable Type Duplex Mode Maximum Distance Between Stations 10 Mbps Category 3 UTP Half or full 328 ft (100 m) 10 Mbps MMF Half or full 1.2 mi (2 km) 100 Mbps Category 5 UTP Half or full 328 ft (100 m) 100 Mbps MMF Half 1312 ft (400 m) 100 Mbps MMF Full 1.
PAGE 12
Installing and Removing the Supervisor Engine Installing the Supervisor Engine The Catalyst 4500 series Supervisor Engine II-Plus TS is only used in Catalyst 4503 switches. Install the Catalyst 4500 series Supervisor Engine II-Plus TS in slot 1. Warning Caution Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when servicing. Statement 1034 To prevent ESD damage, handle supervisor engines by the carrier edges only.
PAGE 13
Installing and Removing the Supervisor Engine Step 9 Using the thumb and forefinger of each hand, simultaneously pivot in both ejector levers to fully seat the supervisor engine in the backplane connector. Caution Always use the ejector levers when installing or removing a supervisor engine. A supervisor engine that is partially seated in the backplane will not function correctly. Step 10 Use a screwdriver to tighten the captive installation screws on each end of the supervisor engine faceplate.
PAGE 14
Installing and Removing the Supervisor Engine Figure 3 Captive Installation Screws and Ejector Levers Ejector lever 113862 Captive installation screw Step 3 Grasp the left and right ejector levers, and simultaneously pivot the levers outward to release the supervisor engine from the backplane connector. Figure 3 shows a close-up of the right ejector lever.
PAGE 15
Attaching Module Interface Cables Attaching Module Interface Cables Figure 4 shows the connector types used to attach interface cables to the supervisor engine. Figure 4 RJ-45 Connector H1567a RJ-45 (both ends) Pin 1 Pin 8 MT-RJ Connector 14367 Figure 5 Note Always keep caps and plugs on the fiber-optic connectors on the cable and the switch when they are not in use.
PAGE 16
Configuring Your Supervisor Engine Configuring Your Supervisor Engine For information and commands to configure your supervisor engine, refer to the Software Configuration Guide for your switch. SFP Guidelines SFP modules are hot-pluggable and field-replaceable, and you can insert them into the eight SFP module slots on the front panel of the Supervisor Engine II+TS. You can use the SFP modules for connections to other network devices. You can use any combination of supported SFP modules.
PAGE 17
SFP Guidelines Fiber-Optic SFP Modules Some fiber-optic SFP modules use LC-type connectors, as shown in Figure 6. Caution Protect your fiber-optic SFP modules by inserting clean dust plugs into the SFP modules after you remove the cables. Be sure to clean the optic surfaces of the fiber-optic cables with a soft antistatic cloth before you reconnect them to another SFP module. Avoid getting dust and other contaminants into the optical bores, as the optics do not work correctly when obstructed with dust.
PAGE 18
SFP Guidelines Note When using shorter distances of single-mode fiber cable, you might need to insert an inline optical attenuator in the link to avoid overloading the receiver. When the fiber-optic cable span is less than 15.43 miles (25 km), you should insert a 5-decibel (dB) or 10-dB inline optical attenuator between the fiber-optic cable plant and the receiving port on the 1000BASE-ZX SFP module at each end of the link. Fiber-optic SFP modules also use MT-RJ connectors, as shown in Figure 7.
PAGE 19
SFP Guidelines Figure 9 CWDM SFP Module (Yellow-Coded CWDM-SFP-1550= Shown) Optical bore dust plug Figure 10 Receive optical bore Transmit optical bore Color coded bale clasp 120533 C C WD l L as M N S # s -S /N 50 1 F : 7 21 PO / C 14 H 01 F 7 1 R 0 2 1 3 0 2 3 4 G 4 0 5 .
PAGE 20
Standards Compliance Specifications Standards Compliance Specifications When installed in a system, the Catalyst 4500 series modules comply with the standards listed in Table 6. Table 6 Standards Compliance Specifications Item Specification Compliance CE1 Marking Safety UL2 60950, CSA3-C22.2 No.
PAGE 21
Obtaining Documentation • Software Configuration Guide—Catalyst 4500 Series, Catalyst 2948G, and Catalyst 2980G Switches • Command Reference—Catalyst 4500 Series, Catalyst 2948G, and Catalyst 2980G Switches • System Message Guide— Catalyst 4500 Series, Catalyst 2926G Series, Catalyst 2948G, and Catalyst 2980G Switches • Layer 3 Services Software Configuration Guide Obtaining Documentation Cisco documentation and additional literature are available on Cisco.com.
PAGE 22
Documentation Feedback Documentation Feedback You can send comments about technical documentation to bug-doc@cisco.com. You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address: Cisco Systems Attn: Customer Document Ordering 170 West Tasman Drive San Jose, CA 95134-9883 We appreciate your comments.
PAGE 23
Obtaining Additional Publications and Information To open a service request by telephone, use one of the following numbers: Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227) EMEA: +32 2 704 55 55 USA: 1 800 553 2447 For a complete list of Cisco TAC contacts, go to this URL: http://www.cisco.com/techsupport/contacts Definitions of Service Request Severity To ensure that all service requests are reported in a standard format, Cisco has established severity definitions.
PAGE 24
Obtaining Additional Publications and Information • iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies learn how they can use technology to increase revenue, streamline their business, and expand services. The publication identifies the challenges facing these companies and the technologies to help solve them, using real-world case studies and business strategies to help readers make sound technology investment decisions.