Datasheet

ManualsBrandsCisco ManualsNetworkingWS-C3560E-12D-E

Data Sheet

Cisco Catalyst 3560-E Series Switches

Cisco

Catalyst

3560-E Series is (Figure 1) an enterprise-class line of standalone

access and aggregation switches that facilitate the deployment of secure converged

applications while maximizing investment protection for evolving network and application

requirements. Combining 10/100/1000 and Power over Ethernet (PoE) configurations with

10 Gigabit Ethernet uplinks, the Cisco Catalyst 3560-E Series access switches enhance

worker productivity by enabling applications such as IP telephony, wireless, and video.

Cisco Catalyst 3560-E Series aggregation switches deliver secure nonstop unified

network services and versatile connectivity in a one rack-unit (1-RU) form factor for space

and power constrained environments, enabling businesses to reduce total cost of

ownership while maximizing investment protection.

Cisco Catalyst 3560-E Series Primary Features

●

Cisco TwinGig converter module for migrating uplinks from Gigabit Ethernet to 10 Gigabit

Ethernet

●

Cisco EnergyWise for greenhouse gas emissions and operational cost optimization by

measuring, reporting, and reducing energy consumption across the entire corporate

infrastructure, well beyond the scope of IT.

●

PoE configurations with 15.4W of PoE on all 48 ports

●

Enhanced PoE supporting up to 20W of PoE per port

●

Industry first portfolio to scale beyond 15.4W per port delivering maximum solution

simplicity for 802.11n access point deployments

●

Access switch models have modular fan and power supply with externally available backup

●

Dual redundant modular power supplies and fans for Cisco Catalyst 3560E-12D and

Catalyst 3560E-12SD aggregation switches for nonstop operation

●

Multicast routing, IPv6 routing, and access control list (ACL) in hardware

●

Out-of-band Ethernet management port along with RS-232 console port

Figure 1. Cisco Catalyst 3560-E Series Access and Aggregation Switches

Summary of content (24 pages)

PAGE 1
Data Sheet Cisco Catalyst 3560-E Series Switches ® ® Cisco Catalyst 3560-E Series is (Figure 1) an enterprise-class line of standalone access and aggregation switches that facilitate the deployment of secure converged applications while maximizing investment protection for evolving network and application requirements.
PAGE 2
Data Sheet Switch Configurations Table 1 shows the Cisco Catalyst 3560-E Series configurations: Table 1. Switch Configurations.
PAGE 3
Data Sheet First [OSPF], Border Gateway Protocol [BGP], Protocol Independent Multicast [PIM] and IPv6 routing such as OSPFv3 and EIGRPv6 Customers can transparently upgrade the software feature set in the Cisco Catalyst 3560-E Series ® Switches through Cisco IOS Software Activation. Software activation authorizes and enables the Cisco IOS Software feature sets. A special file contained in the switch, called a license file, is examined by Cisco IOS Software when the switch is powered on.
PAGE 4
Data Sheet Figure 3. Cisco TwinGig Adapter Converting 10 Gigabit Ethernet X2 Interface into Two Gigabit Ethernet SFP Interfaces Modular Power Supplies The Cisco Catalyst 3560-E Series access switches have one power supply slot and support the following power supplies. PoE switches require a PoE power supply.
PAGE 5
Data Sheet Power over Ethernet The Cisco Catalyst 3560-E Series can provide a lower total cost of ownership for deployments that ® incorporate Cisco IP phones, Cisco Aironet wireless LAN (WLAN) access points, or any IEEE 802.3af-compliant end device. PoE removes the need for wall power to each PoE-enabled device and eliminates the cost for additional electrical cabling and circuits that would otherwise be necessary in IP phone and WLAN deployments.
PAGE 6
Data Sheet ● Port Aggregation Protocol (PAgP) automates the creation of Cisco Fast EtherChannel ® groups or Gigabit EtherChannel groups to link to another switch, router, or server. ● Link Aggregation Control Protocol (LACP) allows the creation of Ethernet channeling with devices that conform to IEEE 802.3ad. This feature is similar to Cisco EtherChannel technology and PAgP.
PAGE 7
Data Sheet ● HSRP provides dynamic load balancing and failover for routed links, up to 32 unique HSRP links supported per unit. The group number can be reused for each VLAN configured in the switch. ● Protocol Independent Multicast (PIM) for IP multicast routing is supported, including PIM sparse mode (PIM-SM), Source Specific Multicast (SSM), PIM dense mode (PIM-DM), PIM sparse-dense mode and Source Specific Multicast (SSM). The IP Services feature set is required.
PAGE 8
Data Sheet Advanced Security The Cisco Catalyst 3560-E Series supports a comprehensive set of security features for connectivity and access control, including ACLs, authentication, port-level security, and identitybased network services with 802.1x and extensions. This set of comprehensive features not only helps prevent external attacks, but defends the network against “man-in-the-middle” attacks, a primary concern in today’s business environment.
PAGE 9
Data Sheet ● Port-based ACLs for Layer 2 interfaces allow security policies to be applied on individual switch ports. ● Secure Shell (SSH) Protocol, Kerberos, and Simple Network Management Protocol Version 3 (SNMPv3) provide network security by encrypting administrator traffic during Telnet and SNMP sessions. SSH Protocol, Kerberos, and the cryptographic version of SNMPv3 require a special cryptographic software image because of U.S. export restrictions.
PAGE 10
Data Sheet Management and Control Features The Cisco Catalyst 3560-E Series Switches come with a rich set of management and control features that include: ● Cisco IOS Software CLI support provides common user interface and command set with all Cisco routers and Cisco Catalyst desktop switches. ● Generic On-Line Diagnostics (GOLD) checks the health of hardware components and verifies proper operation of the system data and control plane at run time and boot time.
PAGE 11
Data Sheet ● Multifunction LEDs per port for port status; half-duplex and full-duplex mode; and 10BASET, 100BASE-TX, and 1000BASE-T indication as well as switch-level status LEDs for system, redundant-power supply, and bandwidth utilization provide a comprehensive and convenient visual management system. ● Jumbo frames (9216 bytes) are available on the 10/100/1000 configurations for advanced data and video applications requiring very large frames.
PAGE 12
Data Sheet Cisco Catalyst 3560 SFP Interconnect Cable The Cisco Catalyst 3560 SFP Interconnect Cable (see Figure 4) provides for a low-cost point-topoint Gigabit Ethernet connection between Cisco Catalyst 3560 switches. The 50cm cable is an alternative to using SFP transceivers when interconnecting Cisco Catalyst 3560 switches through their SFP ports over a short distance. Figure 4.
PAGE 13
Data Sheet Total unicast routes 8K / 12K * 6K / 12K * 0 11K / 20K * Directly connected hosts 6K 4K / 6K * 0 3K / 6K * Indirect routes 2K / 6K * 2K / 6K * 0 8K / 14K * Security ACEs 1K 2K / 4K * 1K 1K QoS ACEs 0.5K / 0.8K * 0.5K / 0.8K * 0.5K / 0.8K * 0.5K PBR ACEs 0 0.5K 0 0.
PAGE 14
Data Sheet Acoustic Noise Mean Time Between Failure (MTBF) International Organization for Standardization (ISO) 7779: bystander position operating to an ambient temperature of 30ºC 3560E-24TD 45 dB 3560E-48TD 45 dB 3560E-24PD 45 dB 3560E-48PD 45 dB 3560E-48PD-F 48 dB 3560E-12D 44 dB 3560E-12SD 44 dB 3560E-24TD 181,086 hours 3560E-24PD 168,753 hours 3560E-48TD 166,907 hours 3560E-48PD 151,196 hours 3560E-48PD-F 151,196 hours 3560E-12D 147,001 hours 3560E-12SD 206,950 hours Tabl
PAGE 15
Data Sheet Standards ● IEEE 802.1s ● IEEE 802.1w ● 1000BASE-LX/LH ● 1000BASE-BX10-U ● IEEE 802.1x ● IEEE 802.3ad ● 1000BASE-BX10-D ● 1000BASE-ZX ● IEEE 802.3af ● IEEE 802.3x full duplex on 10BASE-T, 100BASE-TX, and 1000BASE-T ports ● IEEE 802.1D Spanning Tree Protocol ● 1000BASE-CWDM SFP 1470 nm ● 1000BASE-CWDM SFP 1490 nm ● IEEE 802.1p CoS Prioritization ● IEEE 802.1Q VLAN ● 1000BASE-CWDM SFP 1550 nm ● 1000BASE-CWDM SFP 1570 nm ● IEEE 802.3 10BASE-T specification ● IEEE 802.
PAGE 16
Data Sheet Power-Supply Input Receptacles IEC 320-C14 IEC 320-C14 IEC 320-C13 (IEC60320C14) (IEC60320C14) (IEC60320C14) Power Cord Rating 15A 15A 15A Description – IEC 320-C13 – (IEC60320C14) 12A@100VDC 10A 12AWG Specifications WS-C3560E48PD-SF WS-C3560E24PD-S WS-C3560E48PD-S WS-C3560E24TD-S WS-C3560E48TD-S C3K-PWR1150WAC C3K-PWR750WAC C3K-PWR265WAC C3K-PWR265WDC C3K-PWR300WAC Measured Power Consumption 146W 89W 133W 89W 151W Measured Output BTU/hr 498 303 451 303 514
PAGE 17
Data Sheet to 1060 mbar and relative humidity from 30 to 75 percent. The numbers below indicate a 5 percent traffic load on the switch and its uplinks. PoE Power Consumption 100 Percent Throughput Switch Power Consumption (no PoE loads) The numbers indicate the power consumed by a typical switch under normal conditions. Normal conditions signify a temperature of 25 degrees Celsius, atmospheric pressure in the range of 860 to 1060 mbar and relative humidity from 30 to 75 percent.
PAGE 18
Data Sheet Altitude 10,000 ft. (3000 meters), up to 45°C Operating: -500 to 10,000 ft. (-152 to 3048 m) over allowable temperature range Nonoperating: -1,000 to 50,000 ft. (-304 to 15,240 m) over allowable temperature range MTBF Calculated MTBF must be greater than 300,000 hrs using Telcordia SR-332, Method 1, Case 3. Demonstrated MTBF is 500,000 hrs (with 90% confidence level). EMI and EMC Compliance Calculated MTBF 220,000 hrs with fan (MIL HDBK 217F formula).
PAGE 19
Data Sheet ETSI EN 300 019 - Storage: Class 1.2, Transportation: Class 2.3, In-Use: Class 3.2 Environmental Reduction of Hazardous Substances (ROHS) 5 Noise Specifications Office Product Spec: 48dBA at 30°C (refer to ISO 7779) Telco CLEI code Warranty Standard 90 Day Limited Hardware and Software Warranty Hardware Warranty Cisco Catalyst 3560-E Series Switches come with the standard Cisco 90-day limited warranty for hardware and software, as described at: http://www.cisco.
PAGE 20
Data Sheet WS-C3560E-48TD-E ● 48 10/100/1000 ports + 2 X2-based 10 Gigabit Ethernet ports ● 128-Gbps wire rate, nonblocking switching fabric capacity ● Field-replaceable 265WAC power supply and fan tray ● 1-RU fixed configuration multilayer switch ● IPv6 ● IP Services software feature set (IPS) ● Provides full IPv6 dynamic routing WS-C3560E-24PD-S ● 24 10/100/1000 PoE ports + 2 X2-based 10 Gigabit Ethernet ports ● 128-Gbps wire rate, nonblocking switching fabric capacity ● Field-replaceable 750WAC power
PAGE 21
Data Sheet WS-C3560E-12D-E ● 12 X2-based 10 Gigabit Ethernet ports ● 60 Gbps, backplane utilization 2:1 oversubscribed ● Dual hot-swappable 300WAC or DC power supplies and redundant fans ● 1-RU fixed configuration multilayer switch ● IPv6 ● IP Services software feature set (IPS) ● Provides full IPv6 dynamic routing WS-C3560E-12SD-S ● 12 SFP based Gigabit Ethernet ports + 2 X2-based 10 Gigabit Ethernet ports ● 68 Gbps, wire rate backplane ● Dual hot-swappable 300WAC or DC power supplies and redundant fie
PAGE 22
Data Sheet SFPs for the Cisco Catalyst 3560-E Series GLC-GE-100FX= 100BASE-FX SFP for GE SFP port on 3750,3560.
PAGE 23
Data Sheet CAB-16AWG-AC= AC Power cord, 16AWG CAB-ACA= Plug, Power Cord, Australian, 10A CAB-ACE= Power Cord Europe CAB-ACI= Power Cord-Italian CAB-ACR= Power Cord Argentina CAB-ACS= Power Cord for Switzerland CAB-ACU= Power Cord UK CAB-JPN= Power Cord-Japan CAB-L620P-C13-US= Power Cord, 250VAC, 15A, NEMA L6-20 to C13, US CAB-L620P-C13-JPN= Power Cord, 250VAC, 15A, NEMA L6-20 to C13, JAPAN CAB-IND= Power Cord India CAB-C13-C14-AC Power Cord with C14 connector CAB-SFP-50CM= Catalyst