Datasheet
Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 13 of 22
●
100BASE-TX ports: RJ-45 connectors, two-pair Category 5 UTP cabling
●
100BASE-TX PoE ports: RJ-45 connectors, two-pair Category 5 UTP cabling, power on
pins 1,2 (negative) and 3,6 (positive)
●
1000BASE-T ports: RJ-45 connectors, four-pair Category 5 UTP cabling
●
1000BASE-T SFP-based ports: RJ-45 connectors, four-pair Category 5 UTP cabling
●
1000BASE-SX, -LX/LH, -ZX, and CWDM SFP-based ports: LC fiber connectors
(single/multimode fiber)
●
Cisco Catalyst 3560 SFP Interconnect Cable: two-pair shielded cabling, 50 cm
●
Management console port: RJ-45-to-DB-9 cable for PC connections; for terminal
connections, use RJ-45-to-DB-25 female data-terminal-equipment (DTE) adaptor (can
be ordered separately from Cisco; part number ACS-DSBUASYN=)
Power Connectors
●
Customers can provide power to a switch by using either the internal power supply or
the Cisco RPS 2300. The connectors are located at the back of the switch.
Note: The Cisco Catalyst 3560-8PC and Catalyst 3560-12PC do not have an RPS port.
●
Internal-Power-Supply Connector
●
The internal power supply is an autoranging unit.
●
The internal power supply supports input voltages between 100 and 240 VAC.
●
Use the supplied AC power cord to connect the AC power connector to an AC power
outlet.
●
Cisco RPS Connector
●
The connector offers connection for an optional Cisco RPS 2300 that uses AC input and
supplies DC output to the switch.
●
The connector supports up to six external network devices and provides power to two
failed devices at a time.
●
The connector automatically senses when the internal power supply of a connected
device fails and provides power to the failed device, preventing loss of network traffic.
●
Only the Cisco RPS 2300 (model PWR-RPS2300) should be attached to the redundant-
power-supply receptacle.
Indicators
●
Per-port status LEDs: Link integrity, disabled, activity, speed, full-duplex indications,
PoE applied, PoE error, and PoE disabled indications
●
System-status LEDs: System, RPS, link status, link duplex, link speed, and PoE
indications
Dimensions
(H x W x D)
●
Cisco Catalyst 3560-8PC: 1.73 x 10.6 x 9.1 in. (4.4 x 27 x 23 cm)
●
Cisco Catalyst 3560-12PC: 1.73 x 10.6 x 9.1 in. (4.4 x 27 x 23 cm)
●
Cisco Catalyst 3560-24TS: 1.73 x 17.5 x 11.8 in. (4.4 x 44.5 x 30 cm)
●
Cisco Catalyst 3560-48TS: 1.73 x 17.5 x 11.8 in. (4.4 x 44.5 x 30 cm)
●
Cisco Catalyst 3560-24PS: 1.73 x 17.5 x 11.8 in. (4.4 x 44.5 x 30 cm)
●
Cisco Catalyst 3560-48PS: 1.73 x 17.5 x 14.9 in. (4.4 x 44.5 x 37.8 cm)
●
Cisco Catalyst 3560G-24TS: 1.73 x 17.5 x 14.9 in. (4.4 x 44.5 x 37.8 cm)
●
Cisco Catalyst 3560G-48TS: 1.73 x 17.5 x 16.1 in. (4.4 x 44.5 x 40.9 cm)
●
Cisco Catalyst 3560G-24PS: 1.73 x 17.5 x 14.9 in. (4.4 x 44.5 x 37.8 cm)
●
Cisco Catalyst 3560G-48PS: 1.73 x 17.5 x 16.1 in. (4.4 x 44.5 x 40.9 cm)
Weight
●
Cisco Catalyst 3560-8PC: 5 lb (2.3 kg)
●
Cisco Catalyst 3560-12PC: 5 lb (2.3 kg)
●
Cisco Catalyst 3560-24TS: 8.5 lb (3.9 kg)
●
Cisco Catalyst 3560-48TS: 9.1 lb (4.1 kg)
●
Cisco Catalyst 3560-24PS: 11.3 lb (5.1 kg)
●
Cisco Catalyst 3560-48PS: 13.2 lb (6.0 kg)
●
Cisco Catalyst 3560G-24TS: 12 lb (5.4 kg)
●
Cisco Catalyst 3560G-24PS: 13.5 lb (6.1 kg)
●
Cisco Catalyst 3560G-48TS: 14.0 lb (6.4 kg)
●
Cisco Catalyst 3560G-48PS: 15.5 lb (7.0 kg)
Environmental Ranges
●
Operating temperature: 32 to 113ºF (0 to 45ºC)
●
Storage temperature: -13 to 158ºF (-25 to 70ºC)
●
Operating relative humidity: 10 to 85% (noncondensing)
●
Operating altitude: Up to 10,000 ft (3049m)
●
Storage altitude: Up to 15,000 ft (4573m)
Acoustic Noise
●
ISO 7779: Bystander position operating to an ambient temperature of 25°C
●
Cisco Catalyst 3560-8PC: 0 dBa (no fan)
●
Cisco Catalyst 3560-12PC: 0 dBa (no fan)
●
Cisco Catalyst 3560-24TS: 42 dBa
●
Cisco Catalyst 3560-48TS: 42 dBa