USER GUIDE Wireless-G Broadband Router with 2 Phone Ports Model No: WRP400
About This Guide About This Guide Icon Descriptions While reading through the User Guide you may see various icons that call attention to specific items. Below is a description of these icons: NOTE: This check mark indicates that there is a note of interest and is something that you should pay special attention to while using the product. WARNING: This exclamation point indicates that there is a caution or warning and it is something that could damage your property or product.
Table of Contents Chapter 1: Product Overview 4 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Side Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Chapter 4: Interactive Voice Response Menu 34 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Menu Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Overview Chapter 1 Chapter 1: Product Overview Thank you for choosing the Linksys Wireless-G Broadband Router with 2 Phone Ports. The Router lets you access the Internet via a wireless connection or through one of its four switched ports. You can also use the Router to share resources such as computers, printers and files. The built‑in phone adapter enables Voice-over-IP (VoIP) calls even while you are using the Internet.
Product Overview Chapter 1 Side Panel Vertical Placement The Router has a stand on the panel opposite to the antenna. Rotate the stand 90 degrees, and place the Router on a level surface near an electrical outlet. Reset There are two ways to reset the Router’s factory defaults. Either press and hold the Reset button for approximately ten seconds, or restore the defaults from the Administration > Factory Defaults screen of the Router’s web-based utility.
Product Overview Chapter 1 3. Insert a screw into each hole and leave 3 mm (0.12 inches) of its head exposed. 4. Maneuver the Router so two of the wall-mount slots line up with the two screws. 5. Place the wall-mount slots over the screws and slide the Router down until the screws fit snugly into the wall-mount slots. 60 mm Print this page at 100% size. Cut along the dotted line, and place on the wall to drill precise spacing.
Wireless Security Checklist Chapter 2 Chapter 2: Wireless Security Checklist Wireless networks are convenient and easy to install, so homes with high-speed Internet access are adopting them at a rapid pace. Because wireless networking operates by sending information over radio waves, it can be more vulnerable to intruders than a traditional wired network. Like signals from your cellular or cordless phones, signals from your wireless network can also be intercepted.
Advanced Configuration Chapter 3 Chapter 3: Advanced Configuration After setting up the Router with the Setup Wizard (located on the CD-ROM), the Router will be ready for use. However, if you’d like to change its advanced settings, use the Router’s web-based utility. This chapter describes each web page of the utility and each page’s key functions. You can access the utility via a web browser on a computer connected to the Router.
Advanced Configuration Chapter 3 Static IP If you are required to use a permanent IP address to connect to the Internet, select Static IP. Keep Alive: Redial Period If you select this option, the Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, select Keep Alive. In the Redial Period field, you specify how often you want the Router to check the Internet connection.
Advanced Configuration Chapter 3 L2TP L2TP is a service that applies to connections in Europe and Israel. Internet Connection Type > L2TP Server IP Address This is the IP address of the L2TP Server. Enter the IP address provided by your ISP. User Name and Password Enter the User Name and Password provided by your ISP. Connect on Demand: Max Idle Time You can configure the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time).
Advanced Configuration Chapter 3 Router IP This presents both the Router’s Local IP Address and Subnet Mask as seen by your network. Router IP DHCP Server Setting • Select Clients from DHCP Table Click the Select check box to reserve a client’s IP address. Then click Add Clients. • Manually Adding Client To manually assign an IP address, enter the client’s name in the Enter Client Name field. Enter the IP address you want it to have in the Assign IP Address field.
Advanced Configuration Chapter 3 Automatically adjust clock for daylight saving changes Select this option if you want the Router to automatically adjust for daylight saving time. This option is enabled by default. DynDNS.org Time Server Address If you want to use the Router’s default Network Time Protocol (NTP) server, keep the default, Auto. If you want to specify the NTP server, select Manual, and enter the URL or IP address of the NTP server you want to use.
Advanced Configuration Chapter 3 Clone Your PC’s MAC Click this button to clone the MAC address of the computer you are using. TZO.com Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes. Setup > Advanced Routing This screen is used to set up the Router’s advanced functions. Operating Mode allows you to select the type(s) of advanced functions you use. Dynamic Routing automatically adjusts how packets travel on your network.
Advanced Configuration Chapter 3 Enter the information described below to set up a new static route. Route Entries To set up a static route between the Router and another network, select a number from the dropdown list. Click Delete This Entry to delete a static route. Wireless > Basic Wireless Settings The basic settings for wireless networking are set on this screen. Enter Route Name Enter a name for the Route here, using a maximum of 25 alphanumeric characters.
Advanced Configuration Chapter 3 Configure the following settings for each wireless network: • Wireless Network Name (SSID) The default wireless network uses this name: “linksys” followed by the last four digits of the Router’s wireless MAC address. To rename the default wireless network, enter a unique Wireless Network Name, which is case-sensitive and must not exceed 32 characters (use any of the characters on the keyboard).
Advanced Configuration Chapter 3 Group Key Renewal Enter a Group Key Renewal period, which instructs the Router how often it should change the encryption keys. The default is 3600 seconds. WPA Enterprise This option features WPA used in coordination with a RADIUS server. (RADIUS stands for Remote Authentication Dial-In User Service. This option should only be used when a RADIUS server is connected to the Router.
Advanced Configuration Chapter 3 Key 1-4 If you did not enter a Passphrase, enter the WEP key(s) manually. TX Key Select which TX (Transmit) Key to use. The default is 1. MAC Address Filter List Wireless Client List Click this to open the Wireless Client List screen. Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.
Advanced Configuration Chapter 3 Advanced Wireless Security > Firewall Authentication Type The default is set to Auto, which allows either Open System or Shared Key authentication to be used. With Open System authentication, the sender and the recipient do NOT use a WEP key for authentication. With Shared Key authentication, the sender and recipient use a WEP key for authentication. Select Shared Key to only use Shared Key authentication.
Advanced Configuration Chapter 3 ActiveX ActiveX is a programming language for websites. If you deny ActiveX, you run the risk of not having access to Internet sites created using this programming language. Select this feature to enable ActiveX filtering. Deselect the feature to allow ActiveX usage. Cookies A cookie is data stored on your computer and used by Internet sites when you interact with them. Select this feature to filter cookies. Deselect the feature to allow cookie usage.
Advanced Configuration Chapter 3 6. Decide which days and what times you want this policy to be enforced. Select the individual days during which the policy will be in effect, or select Everyday. Then enter a range of hours and minutes during which the policy will be in effect, or select 24 Hours. 7. You can block websites with specific URL addresses. Enter each URL in a separate URL field. 8. You can also block websites using specific keywords. Enter each keyword in a separate Keyword field.
Chapter 3 Advanced Configuration that use Internet access to perform functions such as videoconferencing or online gaming. Some Internet applications may not require any forwarding.) When users send these types of requests to your network via the Internet, the Router will forward those requests to the appropriate servers (computers). Before using forwarding, you should assign static IP addresses to the designated servers (use the DHCP Reservation feature on the Basic Setup screen).
Advanced Configuration Chapter 3 Applications & Gaming > Port Range Triggering The Port Range Triggering screen allows the Router to watch outgoing data for specific port numbers. The IP address of the computer that sends the matching data is remembered by the Router, so that when the requested data returns through the Router, the data is pulled back to the proper computer by way of IP address and port mapping rules.
Advanced Configuration Chapter 3 Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes. select Manual, and enter the appropriate number in the field provided. Applications and Gaming > QoS Category Quality of Service (QoS) ensures better service to high-priority types of network traffic, which may involve demanding, real-time applications, such as videoconferencing. There are four categories available.
Advanced Configuration Chapter 3 Game Select the appropriate game. If you select Add a New Game, follow the Add a New Game instructions. Ethernet Port Priority Select the appropriate priority: High, Medium (Recommend), Normal, or Low. Click Add to save your changes. Your new entry will appear in the Summary list. Add a New Game QoS > Ethernet Port Ethernet Select the appropriate Ethernet port. Priority Select the appropriate priority: High, Medium (Recommend), Normal, or Low.
Advanced Configuration Chapter 3 Web Utility Access HTTP (HyperText Transport Protocol) is the communications protocol used to connect to servers on the World Wide Web. HTTPS uses SSL (Secured Socket Layer) to encrypt data transmitted for higher security. Select HTTP or HTTPS. HTTP is the default. Remote Upgrade If you want to be able to upgrade the Router remotely, from outside the local network, select Enabled. (You must have the Remote Management feature enabled as well.
Advanced Configuration Chapter 3 Protocol) RTSP server, which is located at the ISP. Otherwise, keep the default, Disabled. IGMP Internet Group Multicast Protocol (IGMP) is used to establish membership in a multicast group and is commonly used for multicast streaming applications. For example, you may have Internet Protocol Television (IPTV) with multiple setup boxes on the same local network.
Advanced Configuration Chapter 3 Diagnostics Ping Test The Ping test checks the status of a connection. IP or URL Address Enter the address of the PC whose connection you wish to test. Packet Size Enter the packet size you want to use. The default is 32 bytes. Times to Ping Enter many times you wish to test it. Start to Ping To run the test, click this button. The Ping Test screen will show if the test was successful. Click Close to return to the Diagnostics screen.
Advanced Configuration Chapter 3 On the Firmware Upgrade screen, click Save Settings to apply your changes, or click Cancel Changes to cancel your changes. Administration > Firmware Upgrade The Firmware Upgrade screen allows you to upgrade the Router’s firmware. Do not upgrade the firmware unless you are experiencing problems with the Router or the new firmware has a feature you want to use.
Advanced Configuration Chapter 3 Status > Local Network Local Network Local MAC Address The MAC address of the Router’s local, wired interface is displayed. Status > Router Router Information Firmware Version The version number of the Router’s current firmware is displayed. Current Time The time set on the Router is displayed. Internet MAC Address The Router’s MAC address, as seen by your ISP, is displayed. Router Name The name of the Router is displayed.
Advanced Configuration Chapter 3 remove a DHCP client, click Delete. To retrieve the most up-to-date information, click Refresh. To exit this screen and return to the Local Network screen, click Close. Status > Wireless Network The Wireless Network screen displays information about your wireless network(s). enter the user name and password provided by your ITSP. Contact your ITSP for more information. (The factory default Admin Login name and password are admin.
Chapter 3 Hardware Version The version number of the Router hardware is displayed. MAC Address The MAC address of the Router is displayed. Client Certificate The status of the client certificate, which indicates that the Router has been authorized by your ITSP, is displayed. System Status Current Time The current date and time of the Router are displayed. Elapsed Time The amount of time elapsed since the last reboot of the Router is displayed.
Advanced Configuration Chapter 3 Call 1/2 Media Loopback The Media Loopback feature allows the ITSP to test the quality of the connection to the Router. The status of the feature is displayed. Voice > System The System screen displays the User Password setting. Voice > System System Configuration User Password Enter the password for user access to the Voice screens. (By default, there is no password.) Miscellaneous Settings No settings are displayed.
Chapter 3 Block Last Caller Enter the ID of the caller blocked via the Block Last Caller service. Accept Last Caller Enter the ID of the caller accepted via the Accept Last Caller service. Advanced Configuration VMWI Ring Splash Len Enter the duration of the ring splash when new messages arrive before the VoiceMail Waiting Indication (VMWI) signal is applied. The range is 0 to 10.0 seconds. The default is 0.
Interactive Voice Response Menu Chapter 4 Chapter 4: Interactive Voice Response Menu Overview This chapter explains how to use the Interactive Voice Response (IVR) Menu to configure the Router’s network settings. Use your telephone’s keypad to enter your commands and select choices, and the Router will use voice responses. Action Command Choices Description **** Use this command to enter the IVR Menu. Ignore Special Information Tones (SITs) or other tones until you hear, “Configuration menu.
Troubleshooting Appendix A Appendix A: Troubleshooting Your computer cannot connect to the Internet. When you are on an Internet phone call, words are dropped intermittently. Follow these instructions until your problem is solved: • If you are using the Router’s wireless function and a cordless phone, they may be using the same frequency and may interfere with each other. Move the cordless phone farther away from the Router.
Appendix A Troubleshooting When you double-click the web browser, you are prompted for a username and password. If you want to get rid of the prompt, follow these instructions. Launch the web browser and perform the following steps (these steps are specific to Internet Explorer but are similar for other browsers): 1. Select Tools > Internet Options. 2. Click the Connections tab. 3. Select Never dial a connection. 4. Click OK. The Router does not have a coaxial port for the cable connection.
Specifications Appendix B Appendix B: Specifications Model WRP400 * Note: Many specifications are programmable within a defined range or list of options. Please see the SPA ATA Administration Guide for details. The target configuration profile is uploaded to the WRP400 at the time of provisioning. Data Networking IP Multicast / IGMP v1, v2, v3/ IGMP Proxy Voice Features Voice Algorithms G.711 (a-law and µ-law) G.726 (16/24/32/40 kbps) G.729 AB G.723.1 (6.3 kbps, 5.
Specifications Appendix B Physical Interfaces 4 100Base-T RJ-45 Ethernet Port (IEEE 802.3) 2 RJ-11 FXS Phone Ports - For Analog Circuit Telephone Device Indicator Lights/ LEDs Documentation USB 2.
Appendix C Appendix C: Warranty Information Contact your service provider if the warranty support issues are to be handled by them as per your service agreements. Limited Warranty Linksys warrants to You that, for a period of one year (the “Warranty Period”), your Linksys Product will be substantially free of defects in materials and workmanship under normal use.
Regulatory Information Appendix D Appendix D: Regulatory Information FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Appendix D Avis d’Industrie Canada Cet appareil numérique de la classe B est conforme aux normes NMB-003 et RSS210 du Canada. L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : 1. il ne doit pas produire de brouillage et 2. il doit accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
Regulatory Information Appendix D Declaration of Conformity with Regard to EU Directive 1999/5/EC (R&TTE Directive) Nederlands [Dutch]: Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de Richtlijn 1999/5/EC.
Regulatory Information Appendix D The following standards were applied during the assessment of the product against the requirements of the Directive 1999/5/EC: • Radio: EN 300 328 and/or EN 301 893 as applicable • EMC: EN 301 489-1, EN 301 489-17 • Safety: EN 60950 and either EN 50385 or EN 50371 Dynamic Frequency Selection (DFS) and Transmit Power Control (TPC) are required for operation in the 5 GHz band. DFS: The equipment meets the DFS requirements as defined in ETSI EN 301 893.
Regulatory Information Appendix D France Product Usage Restrictions For 2,4 GHz, the product should not be used outdoors in the band 2454 - 2483,5 MHz. There are no restrictions when used in other parts of the 2,4 GHz band when used indoors. Check http://www.arcep.fr/ for more details. This product is designed for indoor usage only. Outdoor usage is not recommended, unless otherwise noted. Pour la bande 2,4 GHz, l’ équipement ne doit pas être utilisé en extérieur dans la bande 2454 - 2483,5 MHz.
Appendix D User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE) This document contains important information for users with regards to the proper disposal and recycling of Linksys products.
Appendix D Regulatory Information Eesti (Estonian) - Keskkonnaalane informatsioon Euroopa Liidus asuvatele klientidele Français (French) - Informations environnementales pour les clients de l’Union européenne Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on seadmeid, millel on tootel või pakendil käesolev sümbol , keelatud kõrvaldada koos sorteerimata olmejäätmetega. See sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistest olmejäätmevoogudest.
Appendix D Regulatory Information Lietuvškai (Lithuanian) - Aplinkosaugos informacija, skirta Europos Sąjungos vartotojams Nederlands (Dutch) - Milieu-informatie voor klanten in de Europese Unie Europos direktyva 2002/96/EC numato, kad įrangos, kuri ir kurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį), negalima šalinti kartu su nerūšiuotomis komunalinėmis atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirai nuo bendro buitinių atliekų srauto.
Appendix D Regulatory Information Português (Portuguese) - Informação ambiental para clientes da União Europeia Slovenčina (Slovene) - Okoljske informacije za stranke v Evropski uniji A Directiva Europeia 2002/96/CE exige que o equipamento que exibe este símbolo no produto e/ou na sua embalagem não seja eliminado junto com os resíduos municipais não separados. O símbolo indica que este produto deve ser eliminado separadamente dos resíduos domésticos regulares.
