Cisco Wide Area Application Services Command Reference Software Release 4.2.1 June 22, 2010 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
C O N T E N T S Preface CHAPTER 1 xvii Using the WAAS Command-Line Interface About the WAAS 1-1 Command Line Interface Graphical User Interface 1-1 1-2 1-2 Using Command Modes 1-2 Organization of the WAAS CLI 1-3 Using EXEC Mode 1-4 EXEC Mode Levels 1-4 EXEC Mode Command-Line Processing 1-5 Using Global Configuration Mode 1-5 Configuration Submodes 1-6 Exiting Configuration Mode 1-6 Using Interface Configuration Mode 1-6 Using ACL Configuration Modes 1-7 Using Preposition Configuration Mode 1-7 Using
Contents WAAS Directories on a WAE 1-15 Navigating WAAS Directories 1-15 Directory Descriptions 1-16 Managing WAAS Files Per Device 1-18 CHAPTER 2 Cisco WAAS Software Command Summary CHAPTER 3 CLI Commands 3-1 EXEC Mode Commands cd cifs 3-3 3-4 3-5 clear arp-cache clear cache clear cdp clear ip 3-7 3-8 3-10 3-11 clear license 3-12 clear logging 3-13 clear statistics 3-14 clear statistics accelerator 3-16 clear statistics connection 3-17 clear transaction-log clear users 3-19 3-2
Contents copy sysreport 3-45 copy system-status copy tech-support copy tftp 3-48 3-50 copy virtual-blade cpfile 3-47 3-51 3-52 crypto delete 3-53 crypto export 3-54 crypto generate crypto import crypto pki 3-56 3-58 3-60 debug aaa accounting 3-61 debug aaa authorization debug accelerator debug all 3-65 3-69 debug authentication debug buf 3-73 debug cdp 3-75 debug cli 3-63 3-71 3-77 debug cms 3-79 debug dataserver debug dhcp debug dre 3-81 3-83 3-85 debug egress-method debu
Contents debug stats debug tfo 3-111 3-113 debug translog 3-115 debug wafs 3-117 debug wccp 3-119 delfile 3-121 deltree dir 3-122 3-123 disable disk 3-125 3-126 dnslookup enable exit 3-129 3-130 3-131 find-pattern help 3-132 3-134 install 3-135 less 3-137 license add lls 3-139 ls 3-141 mkdir 3-143 mkfile 3-144 ntpdate 3-145 ping 3-146 pwd 3-147 reload 3-138 3-148 rename 3-149 restore 3-150 rmdir scp 3-154 3-155 script 3-157 setup 3-158 show aaa accountin
Contents show alarms show arp 3-164 3-167 show authentication 3-168 show auto-discovery 3-170 show auto-register 3-171 show banner 3-172 show bypass 3-173 show cache http-metadatacache show cdp 3-176 show cifs 3-182 show clock show cms 3-174 3-184 3-186 show cms secure-store show crypto 3-190 show debugging 3-192 show device-id 3-193 show device-mode 3-194 show directed-mode show disks 3-196 3-197 show egress-methods show filtering list show flash 3-189 3-204 3-205 3-207
Contents show ntp 3-228 show peer optimization 3-230 show policy-engine application show policy-engine status show print-services show processes 3-239 3-241 show running-config show ssh 3-243 3-245 show smb-conf show snmp 3-235 3-237 show radius-server show services 3-231 3-246 3-248 3-254 show startup-config 3-255 show statistics accelerator show statistics aoim 3-257 3-287 show statistics application 3-291 show statistics authentication 3-294 show statistics auto-discovery 3-29
Contents show statistics netstat 3-340 show statistics pass-through show statistics peer 3-341 3-343 show statistics radius 3-346 show statistics services show statistics snmp 3-348 3-349 show statistics synq 3-351 show statistics tacacs 3-352 show statistics tcp 3-354 show statistics tfo 3-358 show statistics udp 3-362 show statistics wccp 3-363 show statistics windows-domain 3-367 show statistics windows-print requests show synq list 3-371 show sysfs volumes show tacacs show tcp
Contents tethereal top 3-414 3-416 traceroute 3-418 transaction-log type 3-420 type-tail 3-421 virtual-blade wafs 3-419 3-423 3-425 whoami 3-427 windows-domain write 3-428 3-431 Global Configuration Mode Commands (config) aaa accounting 3-433 (config) aaa authorization commands (config) accelerator cifs 3-436 3-437 (config) accelerator cifs preposition (config) accelerator epm 3-441 (config) accelerator http 3-442 (config) accelerator mapi 3-439 3-444 (config) accelerator nfs
Contents (config) central-manager (config) clock (config) cms 3-482 3-484 3-488 (config) crypto pki 3-491 (config) crypto ssl 3-492 (config) device mode 3-494 (config) directed-mode 3-496 (config) disk disk-name 3-497 (config) disk encrypt 3-499 (config) disk error-handling 3-500 (config) disk logical shutdown 3-501 (config) disk object-cache extend (config) egress-method (config) end 3-502 3-503 3-505 (config) exec-timeout (config) exit 3-506 3-507 (config) flow monitor (config)
Contents (config) logging host (config) ntp 3-544 3-546 (config) peer 3-548 (config) policy-engine application classifier 3-549 (config) policy-engine application map adaptor EPM 3-551 (config) policy-engine application map adaptor WAFS transport (config) policy-engine application map basic 3-555 (config) policy-engine application map other optimize DRE (config) policy-engine application map other optimize full (config) policy-engine application map other pass-through (config) policy-engine appl
Contents (config) tfo exception (config) tfo optimize 3-608 3-609 (config) tfo tcp adaptive-buffer-sizing (config) tfo tcp keepalive 3-610 3-611 (config) tfo tcp optimized-mss 3-612 (config) tfo tcp optimized-receive-buffer (config) tfo tcp optimized-send-buffer (config) tfo tcp original-mss 3-614 3-615 (config) tfo tcp original-receive-buffer (config) tfo tcp original-send-buffer (config) transaction-logs (config) username 3-613 3-616 3-617 3-618 3-621 (config) virtual-blade 3-623 (config
Contents (config-if) standby 3-660 Standard ACL Configuration Mode Commands (config-std-nacl) delete 3-665 (config-std-nacl) deny 3-666 (config-std-nacl) exit 3-668 (config-std-nacl) list 3-669 (config-std-nacl) move 3-670 (config-std-nacl) permit 3-671 Extended ACL Configuration Mode Commands (config-ext-nacl) delete 3-677 (config-ext-nacl) exit 3-682 (config-ext-nacl) list 3-683 (config-ext-nacl) move 3-684 (config-ext-nacl) permit 3-685 Preposition Configuration Mode Commands (co
Contents (config-vb) cpu-list 3-714 (config-vb) description (config-vb) device (config-vb) disk 3-716 3-717 3-720 (config-vb) interface (config-vb) memory (config-vb) vnc 3-722 3-723 3-724 PKI Certificate Authority Configuration Mode Commands (config-ca) ca-certificate (config-ca) description 3-725 3-727 3-728 (config-ca) revocation-check 3-729 PKI Global Settings Configuration Mode Commands (config-pki-global-settings) ocsp 3-731 3-732 (config-pki-global-settings) revocation-check 3-733
Contents SSL Host Peering Service Configuration Mode Commands (config-ssl-peering) cipher-list 3-761 (config-ssl-peering) peer-cert-verify (config-ssl-peering) version 3-762 3-763 SSL Management Service Configuration Mode Commands (config-ssl-mgmt) cipher-list APPENDIX A Acronyms and Abbreviations 3-765 3-767 (config-ssl-mgmt) peer-cert-verify (config-ssl-mgmt) version 3-759 3-768 3-769 A-1 CLI COMMAND SUMMARY BY MODE Cisco Wide Area Application Services Command Reference xvi OL-21611-01
Preface This preface describes who should read the Cisco Wide Area Application Services Command Reference, how it is organized, and its document conventions.
Preface Chapter Description Chapter 3, “CLI Commands” Provides detailed information for the following types of CLI commands for the WAAS software: • Commands you can enter after you log in to the WAAS device (EXEC mode). • Configuration mode commands that you can enter after you log in to the WAAS device, and then access configuration mode and its subset of modes. The description of each command includes the syntax of the command and any related commands, when appropriate.
Preface Note Caution Means reader take note. Notes contain helpful suggestions or references to materials not contained in the manual. Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.
Preface Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.
C H A P T E R 1 Using the WAAS Command-Line Interface This chapter describes how to use the WAAS CLI, including an explanation of CLI command modes, navigation and editing features, and help features.
Chapter 1 Using the WAAS Command-Line Interface Using Command Modes Command Line Interface The WAAS CLI allows you to configure, manage, and monitor WAAS devices on a per-device basis through a console connection or a terminal emulation program. The WAAS CLI also allows you to configure certain features that are only supported through the WAAS CLI (for example, configuring LDAP signing on a WAE).
Chapter 1 Using the WAAS Command-Line Interface Using Command Modes • Organization of the WAAS CLI, page 1-3 • Using EXEC Mode, page 1-4 • Using Global Configuration Mode, page 1-5 • Using Interface Configuration Mode, page 1-6 • Using ACL Configuration Modes, page 1-7 • Using Preposition Configuration Mode, page 1-7 • Using Virtual Blade Configuration Mode, page 1-7 • Using PKI Certificate Authority Configuration Mode, page 1-7 • Using PKI Global Settings Configuration Mode, page 1-8 •
Chapter 1 Using the WAAS Command-Line Interface Using Command Modes • Virtual blade configuration mode—Configures virtual blades that reside in a WAE or WAVE device for additional services, including operating systems and applications, that work with the WAAS device. To use this mode, enter the virtual-blade command. • PKI certificate authority configuration mode—Configures public key infrastructure (PKI) encryption certificate authorities on a WAAS device.
Chapter 1 Using the WAAS Command-Line Interface Using Command Modes • Privileged level—The prompt for the privileged-level EXEC command line is the pound sign (#). To execute an EXEC command, enter the command at the EXEC system prompt and press the Return key.
Chapter 1 Using the WAAS Command-Line Interface Using Command Modes Configuration Submodes Configuration submodes are used for the configuration of specific features within the scope of a given configuration mode.
Chapter 1 Using the WAAS Command-Line Interface Using Command Modes To exit interface configuration mode, use the exit command to return to global configuration mode: WAE(config-if)# exit WAE(config)# Using ACL Configuration Modes Use the ACL configuration modes to create and modify standard and extended access list configuration on a WAAS device. From global configuration mode, you can enter the standard and extended ACL configuration modes.
Chapter 1 Using the WAAS Command-Line Interface Using Command Modes To enter this mode, use the crypto pki ca command from the global configuration mode. To exit PKI certificate authority configuration mode, use the exit command to return to global configuration mode: WAE(config-ca)# exit WAE(config)# Using PKI Global Settings Configuration Mode Use PKI global settings configuration mode to configure OCSP and revocation checking.
Chapter 1 Using the WAAS Command-Line Interface Using Command Modes WAE(config)# Using SSL Host Peering Service Configuration Mode Use SSL host peering service configuration mode to configure secure socket layer (SSL) encryption peering services on a WAAS device. SSL peering service configuration parameters control secure communications established by the SSL accelerator between WAE devices while optimizing SSL connections.
Chapter 1 Using the WAAS Command-Line Interface Using Command Modes Table 1-1 WAAS Command Modes Summary (continued) Command Mode Prompt Exit Method interface configuration From global configuration mode, use the interface command. WAE(config-if)# To return to global configuration mode, use the exit command. standard ACL configuration From global configuration mode, use the ip access-list standard command.
Chapter 1 Using the WAAS Command-Line Interface Using Command Modes Table 1-1 WAAS Command Modes Summary (continued) Command Mode Access Method Prompt Exit Method SSL host peering service configuration From global configuration mode, use the crypto ssl services host-service peering command. WAE(config-ssl-peering)# To return to global configuration mode, use the exit command. From global configuration mode, use the crypto ssl management-service command.
Chapter 1 Using the WAAS Command-Line Interface Using Command-Line Processing Shutting down all services, will Reload requested by CLI@ttyS0. Restarting system.
Chapter 1 Using the WAAS Command-Line Interface Checking Command Syntax Table 1-2 Command-Line Processing Keystroke Combinations (continued) Keystroke Combinations Function Ctrl-U; Ctrl-X Deletes from the cursor to the beginning of the command line. Ctrl-W Deletes the last word typed. Esc-B Moves the cursor back one word. Esc-D Deletes from the cursor to the end of the word. Esc-F Moves the cursor forward one word.
Chapter 1 Using the WAAS Command-Line Interface Using the no Form of Commands Enter the day and month as prompted, and use the question mark for additional instructions. WAE# clock set 13:32:00 23 December ? <1993-2035> Year Now you can complete the command entry by entering the year. WAE# clock set 13:32:00 23 December 05 ^ %Invalid input detected at '^' marker. WAE# The caret symbol (^) and help response indicate an error with the 05 entry. To display the correct syntax, press Ctrl-P or the Up Arrow.
Chapter 1 Using the WAAS Command-Line Interface Saving Configuration Changes Saving Configuration Changes To avoid losing new configurations, save them to NVRAM using the copy or write commands, as shown in the following example: WAE# copy running-config startup-config or WAE# write See the copy running-config startup-config and write commands for more information about running and saved configuration modes.
Chapter 1 Using the WAAS Command-Line Interface WAAS Directories on a WAE Table 1-3 WAAS Navigation Commands (continued) Command Description pwd Present Working Directory—Lists the complete path from where this command is entered. rmdir directory-name Delete Directory—Removes the specified directory from the current directory path. All files in the directory must first be deleted before the directory can be deleted.
Chapter 1 Using the WAAS Command-Line Interface WAAS Directories on a WAE Table 1-4 describes the directories that contain information that is useful for troubleshooting or monitoring. Table 1-4 Note WAAS Directory Descriptions Directory/File Name Contents actona This directory contains the current software image installed on the WAAS device and any previous images that were installed. logs This directory contains application-specific logs used in troubleshooting.
Chapter 1 Using the WAAS Command-Line Interface Managing WAAS Files Per Device Managing WAAS Files Per Device The WAAS CLI provides several commands for managing files and viewing their contents per device. These commands are entered from privileged EXEC mode. Table 1-5 describes the WAAS file management commands.
Chapter 1 Using the WAAS Command-Line Interface Managing WAAS Files Per Device Note To back up, restore, or create a system report about the WAFS-specific configuration on a WAE, use the wafs EXEC command. To save the WAFS-system specific configuration information, use the wafs backup-config EXEC command. See the Cisco Wide Area Application Services Configuration Guide for more information on backing up.
Chapter 1 Using the WAAS Command-Line Interface Managing WAAS Files Per Device Cisco Wide Area Application Services Command Reference 1-20 OL-21611-01
C H A P T E R 2 Cisco WAAS Software Command Summary This chapter summarizes the Cisco WAAS 4.1.1 software commands. Table 2-1 lists the WAAS commands (alphabetically) and indicates the command mode for each command. The commands used to access configuration modes are marked with an asterisk. Commands that do not indicate a particular mode are EXEC mode commands. The same command may have different effects when entered in a different command mode, so they are listed and documented separately.
Chapter 2 Table 2-1 Cisco WAAS Software Command Summary Command Summary (continued) Command Description CLI Mode Device Mode (config) alarm overload-detect Configures the detection of an alarm overload. global configuration All (config) asset Configures the tag name for the asset tag string. global configuration All (config) authentication configuration Configures administrative authentication and global configuration authorization parameters.
Chapter 2 Cisco WAAS Software Command Summary Table 2-1 Command Summary (continued) Command Description CLI Mode Device Mode (config) central-manager global configuration In application-accelerator mode, used to specify the IP address of the WAAS Central Manager with which the WAE needs to register. In central-manager mode, used to specify the WAAS Central Manager’s role and GUI port number. All cifs Controls CIFS adapter operations and run-time configurations.
Chapter 2 Table 2-1 Cisco WAAS Software Command Summary Command Summary (continued) Command Description CLI Mode cms Configures the parameters for the Centralized privileged-level EXEC Management System (CMS) embedded database. All cms secure-store Configures secure store encryption All (config) cms Schedules the maintenance and enables the global configuration Centralized Management System on a specific WAAS device. All configure* Enters configuration mode from privileged EXEC mode.
Chapter 2 Cisco WAAS Software Command Summary Table 2-1 Command Summary (continued) Command Description CLI Mode Device Mode crypto generate Generates a self-signed certificate or a certificate signing request. privileged-level EXEC All crypto import Imports SSL certificate and key files. privileged-level EXEC applicationaccelerator crypto pki Initializes the PKI managed store.
Chapter 2 Table 2-1 Cisco WAAS Software Command Summary Command Summary (continued) Command Description CLI Mode Device Mode debug snmp Configures SNMP debugging. privileged-level EXEC All debug stats Configures statistics debugging. privileged-level EXEC All debug tfo Configures TFO flow optimization debugging. privileged-level EXEC applicationaccelerator debug translog Configures transaction logging debugging.
Chapter 2 Cisco WAAS Software Command Summary Table 2-1 Command Summary (continued) Command Description CLI Mode Device Mode (config) disk encrypt Enables disk encryption. global configuration applicationaccelerator (config) disk error-handling Configures how the disk errors should be handled. global configuration All (config) disk logical shutdown Shuts down the RAID-5 logical disk drive. global configuration All (config) disk object-cache extend Enables extended object cache, .
Chapter 2 Table 2-1 Cisco WAAS Software Command Summary Command Summary (continued) Command Description CLI Mode Device Mode (config-if) half-duplex Sets the current interface to half-duplex mode. interface configuration All help Provides assistance for the WAAS command-line interface in EXEC mode. user-level EXEC and privileged-level EXEC All (config) help Provides assistance for the WAAS command-line interface.
Chapter 2 Cisco WAAS Software Command Summary Table 2-1 Command Summary (continued) Command Description CLI Mode Device Mode (config) ip access-list* Creates and modifies the access lists for controlling access to interfaces or applications. Provides access to ACL configuration mode. global configuration All (config) kerberos Configures user authentication against a Kerberos database. global configuration All (config) kernel kdb Enables the kernel debugger configuration mode.
Chapter 2 Table 2-1 Cisco WAAS Software Command Summary Command Summary (continued) Command Description CLI Mode Device Mode (config-std-nacl) move Moves a line to a new position within the standard ACL standard ACL configuration All (config-ext-nacl) move Moves a line to a new position within the extended ACL extended ACL configuration All (config-if) mtu Sets the interface Maximum Transmission Unit (MTU) packet size.
Chapter 2 Table 2-1 Cisco WAAS Software Command Summary Command Summary (continued) Command Description CLI Mode Device Mode (config) policy-engine application map basic Deletes a specific basic (static) application global configuration policy map from the WAE’s list of application policy maps. applicationaccelerator (config) policy-engine application map other optimize DRE Configures the WAE’s optimize DRE command action for nonclassified traffic.
Chapter 2 Table 2-1 Cisco WAAS Software Command Summary Command Summary (continued) Command Description CLI Mode Device Mode (config-preposition) root Sets the root directory for a preposition directive. preposition configuration applicationaccelerator (config-preposition) scan-type Sets the file scanning type for a preposition directive. preposition configuration applicationaccelerator (config-preposition) schedule Sets the schedule for a preposition directive.
Chapter 2 Cisco WAAS Software Command Summary Table 2-1 Command Summary (continued) Command Description CLI Mode Device Mode show cache http-metadatacache Displays HTTP metadata cache information. privileged-level EXEC applicationaccelerator show cdp Displays the CDP configuration. privileged-level EXEC All show cifs Displays CIFS run-time information. user-level EXEC and privileged-level EXEC applicationaccelerator show clock Displays the system clock.
Chapter 2 Table 2-1 Cisco WAAS Software Command Summary Command Summary (continued) Command Description CLI Mode Device Mode show license Displays the license information. privileged-level EXEC All show logging Displays the system logging configuration. user-level EXEC and privileged-level EXEC All show memory Displays the memory blocks and statistics. privileged-level EXEC All show ntp Displays the NTP configuration status.
Chapter 2 Cisco WAAS Software Command Summary Table 2-1 Command Summary (continued) Command Description CLI Mode Device Mode show statistics connection Displays the connection statistics for a WAE. privileged-level EXEC applicationaccelerator show statistics connection auto-discovery Displays the auto-discovery connection statistics for a WAE.
Chapter 2 Table 2-1 Cisco WAAS Software Command Summary Command Summary (continued) Command Description CLI Mode Device Mode show statistics services Displays the services statistics. user-level EXEC and privileged-level EXEC All show statistics snmp Displays the SNMP statistics. user-level EXEC and privileged-level EXEC All show statistics synq Displays statistics for the SynQ module.
Chapter 2 Cisco WAAS Software Command Summary Table 2-1 Command Summary (continued) Command Description CLI Mode Device Mode show wccp Displays the WCCP information for a WAE. user-level EXEC and privileged-level EXEC applicationaccelerator show windows-domain Displays the Windows domain configuration. user-level EXEC and privileged-level EXEC All (config-if) shutdown Shuts down the specified interface.
Chapter 2 Table 2-1 Cisco WAAS Software Command Summary Command Summary (continued) Command Description CLI Mode Device Mode (config) tacacs Configures the TACACS+ parameters on a WAAS device. global configuration All (config) tcp Configures the TCP parameters. global configuration All tcpdump Dumps the TCP traffic on the network. privileged-level EXEC All telnet Starts the Telnet client.
Chapter 2 Cisco WAAS Software Command Summary Table 2-1 Command Summary (continued) Command Description CLI Mode Device Mode type Displays a file. user-level EXEC and privileged-level EXEC All type-tail Displays the last several lines of a file. user-level EXEC and privileged-level EXEC All (config) username Establishes the username authentication. global configuration All (config-ssl-accelerated) version Specifies the type of SSL protocol to use for accelerated services.
Chapter 2 Table 2-1 Cisco WAAS Software Command Summary Command Summary (continued) Command Description CLI Mode Device Mode (config) windows-domain Configures Windows domain server options. global configuration All write Writes or erases the startup configurations to privileged-level EXEC NVRAM or to a terminal session, or writes the MIB persistence configuration to disk.
C H A P T E R 3 CLI Commands This chapter provides detailed information for the following types of CLI commands for the WAAS software: • EXEC mode commands that you can enter after you log in to the WAAS device. See the “EXEC Mode Commands” section for a complete listing of commands. • Global configuration mode commands that you can enter after you log in to the WAAS device and access global configuration mode. See the “Global Configuration Mode Commands” section for a complete listing of commands.
Chapter 3 CLI Commands • SSL host peering service configuration mode commands that you can enter after you access SSL host peering service configuration mode. See the “SSL Host Peering Service Configuration Mode Commands” section for a complete listing of commands. • SSL management service configuration mode commands that you can enter after you access SSL management service configuration mode. See the “SSL Management Service Configuration Mode Commands” section for a complete listing of commands.
Chapter 3 CLI Commands EXEC Mode Commands Use the EXEC mode for setting, viewing, and testing system operations. In general, the user EXEC commands allow you to connect to remote devices, change terminal line settings on a temporary basis, perform basic tests, and list system information. The EXEC mode is divided into two access levels: user and privileged. The user EXEC mode is used by local and general system administrators, while the privileged EXEC mode is used by the root administrator.
Chapter 3 CLI Commands cd cd To change from one directory to another directory in the WAAS software, use the cd EXEC command. cd directoryname Syntax Description directoryname Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Directory name. central-manager Usage Guidelines Use this command to navigate between directories and for file management. The directory name becomes the default prefix for all relative paths.
Chapter 3 CLI Commands cifs cifs To control legacy CIFS adapter operations and run-time configurations, use the cifs EXEC command. cifs auto-discovery {disable | enable | reset-log} cifs mss value cifs restart [core | edge] cifs reverse-dns {active | disable | enable} cifs session disconnect [client-ip ipaddress | server-ip ipaddress] Syntax Description auto-discovery Controls the CIFS auto-discovery configuration and debug. disable Disables the CIFS server operation.
Chapter 3 CLI Commands cifs Use the cifs restart command to restart the WAFS services for a configuration change without having to reboot the WAE.
Chapter 3 CLI Commands clear arp-cache clear arp-cache To clear the ARP cache, use the clear arp-cache EXEC command. clear arp-cache [ipaddress | interface {GigabitEthernet 1-2/port | PortChannel 1-2 | Standby 1}] Syntax Description arp-cache Clears the ARP cache. ipaddress (Optional) ARP entries for the IP address. interface (Optional) Clears all ARP entries on the interface. GigabitEthernet 1-2/port GigabitEthernet interface (slot/port). PortChannel 1-2 PortChannel interface number.
Chapter 3 CLI Commands clear cache clear cache To clear cached objects, use the clear cache EXEC command. clear cache {cifs | dre | http-metadatacache {all | conditional-response | redirect-response | unauthorized-response} [url]} Syntax Description cifs Clears the CIFS cache. dre Clears the DRE cache. http-metadatacache Clears the HTTP accelerator metadata cache. all Clears cache entries for all HTTP metadata cache response types.
Chapter 3 CLI Commands clear cache Related Commands license add show cache http-metadatacache show interface show license show wccp Cisco Wide Area Application Services Command Reference OL-21611-01 3-9
Chapter 3 CLI Commands clear cdp clear cdp To clear Cisco Discovery Protocol statistics, use the clear cdp EXEC command. clear cdp {counters | table} Syntax Description cdp Resets the Cisco Discovery Protocol (CDP) statistical data. counters Clears the CDP counters. table Clears the CDP tables. Defaults No default behavior or values.
Chapter 3 CLI Commands clear ip clear ip To clear IP access list statistics, use the clear ip EXEC command. clear ip access-list counters [acl-num | acl-name] Syntax Description ip Clears the IP statistical information. access-list Clears the access list statistical information. counters Clears the IP access list counters. acl-num (Optional) Clears the counters for the specified access list, identified using a numeric identifier (standard access list: 1–99; extended access list: 100–199).
Chapter 3 CLI Commands clear license clear license To clear licensing configuration, use the clear license EXEC command. clear license [license-name] Syntax Description license Removes all installed software licenses, when specified without options. license-name Name of the software license to remove. The following license names are supported: Defaults No default behavior or values.
Chapter 3 CLI Commands clear logging clear logging To clear syslog messages saved in a disk file, use the clear logging EXEC command. clear logging Syntax Description logging Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Clears the syslog messages saved in the disk file. central-manager Usage Guidelines The clear logging command removes all current entries from the syslog.txt file but does not make an archive of the file.
Chapter 3 CLI Commands clear statistics clear statistics To reset statistics data, use the clear statistics EXEC command. clear statistics {all | aoim | authentication | auto-discovery {all | blacklist}| datamover | directed-mode | dre [global] | filtering | flow monitor tcpstat-v1 | generic-gre | icmp | inline | ip | pass-through | peer dre | radius | synq | tacacs | tcp | tfo | udp | wccp | windows-domain | windows-print} Syntax Description Defaults all Clears all statistics.
Chapter 3 CLI Commands clear statistics Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines The clear statistics command clears all statistical counters from the parameters given. Use this command to monitor fresh statistical data for some or all features without losing cached objects or configurations. Not all command options are applicable for a device in central-manager mode.
Chapter 3 CLI Commands clear statistics accelerator clear statistics accelerator To clear all global statistics, use the clear statistics accelerator EXEC command. clear statistics accelerator {cifs | epm | generic | http | mapi | nfs | ssl | video} Syntax Description cifs Clears the statistics for the CIFS application accelerator. epm Clears the statistics for the EPM application accelerator. generic Clears the statistics for generic accelerator.
Chapter 3 CLI Commands clear statistics connection clear statistics connection To clear connection statistics, use the clear statistics connection EXEC command.
Chapter 3 CLI Commands clear statistics connection Command Modes EXEC Device Modes application-accelerator Examples The following example shows how to clear the connection 1 statistics on the WAAS device: WAE# clear statistics connection conn-id 1 Related Commands clear statistics clear statistics accelerator Cisco Wide Area Application Services Command Reference 3-18 OL-21611-01
Chapter 3 CLI Commands clear transaction-log clear transaction-log To archive working transaction log file, use the clear transaction-log EXEC command. clear transaction-log {flow} Syntax Description transaction-log Clears the transaction log. flow Clears the TFO transaction log. Defaults No default behavior or values.
Chapter 3 CLI Commands clear users clear users To clear user connections or to unlock users that have been locked out, use the clear users EXEC command. clear users [administrative | locked-out {all | username username}] Syntax Description users Clears the connections (logins) of authenticated users. administrative (Optional) Clears the connections (logins) of administrative users authenticated through a remote login service. locked-out (Optional) Unlocks specified locked-out user accounts.
Chapter 3 CLI Commands clear users The following example shows how to unlock the account for username darcy: WAE(config)# clear users locked-out username darcy Related Commands clear arp-cache (config) authentication strict-password-policy Cisco Wide Area Application Services Command Reference OL-21611-01 3-21
Chapter 3 CLI Commands clear windows-domain-log clear windows-domain-log To clear the Windows domain server log file, use the clear windows-domain-log EXEC command. clear windows-domain-log Syntax Description windows-domain-log Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Clears the Samba, Kerberos, and Winbind log files.
Chapter 3 CLI Commands clock clock To set clock functions or update the calendar, use the clock EXEC command. clock {read-calendar | set time day month year | update-calendar} Syntax Description read-calendar Reads the calendar and updates the system clock. set time day month year Sets the time and date. Current time in hh:mm:ss format (hh: 00–23; mm: 00–59; ss: 00–59). Day of the month (1–31).
Chapter 3 CLI Commands cms cms To configure the Centralized Management System (CMS) embedded database parameters for a WAAS device, use the cms EXEC command. cms {config-sync | deregister [force] | lcm {enable | disable} | maintenance {full | regular} | recover {identity word} | restore filename | validate} cms database {backup | create | delete | downgrade [script filename]} Syntax Description Defaults config-sync Sets the node to synchronize configuration with the WAAS Central Manager.
Chapter 3 CLI Commands cms Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines Use the cms config-sync command to enable registered WAAS devices and standby WAAS Central Manager to contact the primary WAAS Central Manager immediately for a getUpdate (get configuration poll) request before the default polling interval of 5 minutes.
Chapter 3 CLI Commands cms Use the lcm command to configure local/central management (LCM) on a WAE. The LCM feature allows settings that are configured using the device CLI or GUI to be stored as part of the WAAS network-wide configuration data (enable or disable).
Chapter 3 CLI Commands cms secure-store cms secure-store To configure secure store encryption, use the cms secure-store EXEC commands. cms secure-store {init | open | change | clear | reset} Syntax Description init Initializes secure store encryption on the WAAS device and opens the secure store. On the Central Manager, this command prompts you to enter the secure store encryption pass phrase.
Chapter 3 CLI Commands cms secure-store When you enable secure store on Central Manager, the data is encrypted using a key encryption key generated from the pass phrase you enter with SHA-1 hashing and an AES 256-bit algorithm. When you enable secure store on a WAE device, the data is encrypted using a 256-bit key encryption key generated by SecureRandom, a cryptographically strong pseudorandom number. You must enter a password to enable secure store.
Chapter 3 CLI Commands cms secure-store The following example shows how to deactivates secure store encryption: waas-cm# cms secure-store clear Secure store clear will result in deletion of CM pki store certificate/private key files Do you want to continue(yes/no)?yes Stopping cms. Successfully migrated user passwords Successfully migrated Cifs preposition password Successfully migrated Cifs dynamic shares password Successfully migrated key store secure-store clear Starting cms.
Chapter 3 CLI Commands configure configure To enter global configuration mode, use the configure EXEC command. You must be in global configuration mode to enter global configuration commands. configure To exit global configuration mode, use the end or exit commands. You can also press Ctrl-Z to exit from global configuration mode. Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands copy cdrom copy cdrom To copy software release files from a CD-ROM, use the copy cdrom EXEC command. copy cdrom install filedir filename Syntax Description cdrom Copies a file from the CD-ROM. install filedir filename Installs the software release from the directory location and filename specified. Defaults No default behavior or values.
Chapter 3 CLI Commands copy cdrom wow-recovery copy cdrom wow-recovery To recover Windows on a virtual blade without reloading the software, use the copy cdrom wow-recovery EXEC command. copy cdrom wow-recover install filedir filename Syntax Description cdrom Copies the Windows system files from the CD-ROM. wow-recovery Recovers the Windows operating system. install filedir filename Installs the Windows operating system on the virtual blade from the directory location and Windows filename.
Chapter 3 CLI Commands copy compactflash copy compactflash To copy software release files from a CompactFlash card, use the copy compactflash EXEC command. copy compactflash install filename Syntax Description compactflash Copies a file from the CompactFlash card. install filename Installs a software release from an image filename. Defaults No default behaviors or values.
Chapter 3 CLI Commands copy disk copy disk To copy the configuration or image data from a disk to a remote location using FTP or to the startup configuration, use the copy disk EXEC command. copy disk {ftp {hostname | ip-address} remotefiledir remotefilename localfilename | startup-config filename} Syntax Description disk Copies a local disk file. ftp Copies to a file on an FTP server. hostname Hostname of the FTP server. ip-address IP address of the FTP server.
Chapter 3 CLI Commands copy disk write Cisco Wide Area Application Services Command Reference OL-21611-01 3-35
Chapter 3 CLI Commands copy ftp copy ftp To copy software configuration or image data from an FTP server, use the copy ftp EXEC command.
Chapter 3 CLI Commands copy ftp Use the copy ftp wow-recovery EXEC command to copy a Windows operating system image from an FTP server to a virtual blade partition on the WAAS device. To show progress, this command prints a number sign (#) for each 1 MB of data that is copied. Examples The following example shows how to copy an image file from an FTP server and install the file on the local device: WAE# copy ftp install 10.1.1.1 cisco/waas/4.1 WAAS-4.1.1-k9.
Chapter 3 CLI Commands copy ftp Sending:RETR 7326_bios.bin Opening BINARY mode data connection for 7326_bios.bin (834689 bytes). Fri Jan 7 15:29:07 UTC 2005 BIOS installer running! Do not turnoff the system till BIOS installation is complete. Flash chipset:Macronix 29LV320B 0055000.
Chapter 3 CLI Commands copy http copy http To copy configuration or image files from an HTTP server to the WAAS device, use the copy http EXEC command. copy http install {hostname | ip-address}remotefiledir remotefilename [port portnum] [proxy proxy_portnum] [username username password] Syntax Description http Copies the file from an HTTP server. install Copies the file from an HTTP server and installs the software release file to the local device. hostname Name of the HTTP server.
Chapter 3 CLI Commands copy http Examples The following example shows how to copy an image file from an HTTP server and install the file on the WAAS device: WAE# copy http install 10.1.1.1 //ftp-sj.cisco.com/cisco/waas/4.0 WAAS-4.0.0-k9.bin Enter username for remote ftp server:biff Enter password for remote ftp server:***** Initiating FTP download... printing one # per 1MB downloaded Sending:USER biff 10.1.1.1 FTP server (Version) Mon Feb 28 10:30:36 EST 2000) ready. Password required for biff.
Chapter 3 CLI Commands copy http Erasing block 2f:280000 - 28ffff Erasing block 30:290000 - 29ffff Erasing block 31:2a0000 - 2affff Erasing block 32:2b0000 - 2bffff Erasing block 33:2c0000 - 2cffff Erasing block 34:2d0000 - 2dffff Erasing block 35:2e0000 - 2effff Erasing block 36:2f0000 - 2fffff Programming block 2f:280000 - 28ffff Programming block 30:290000 - 29ffff Programming block 31:2a0000 - 2affff Programming block 32:2b0000 - 2bffff Programming block 33:2c0000 - 2cffff Programming block 34:2d0000
Chapter 3 CLI Commands copy running-config copy running-config To copy a configuration or image data from the current configuration, use the copy running-config EXEC command. copy running-config {disk filename | startup-config | tftp {hostname | ip-address} remotefilename} Syntax Description running-config Copies the current system configuration. disk filename Copies the current system configuration to a disk file. Specify the name of the file to be created on a disk.
Chapter 3 CLI Commands copy running-config wafs write Cisco Wide Area Application Services Command Reference OL-21611-01 3-43
Chapter 3 CLI Commands copy startup-config copy startup-config To copy configuration or image data from the startup configuration, use the copy startup-config EXEC command. copy startup-config {disk filename | running-config | tftp {hostname | ip-address} remotefilename} Syntax Description startup-config Copies the startup configuration. disk filename Copies the startup configuration to a disk file. Specify the name of the startup configuration file to be copied to the local disk.
Chapter 3 CLI Commands copy sysreport copy sysreport To copy system troubleshooting information from the device, use the copy sysreport EXEC command. copy sysreport disk filename copy sysreport ftp {hostname | ip-address} remotedirectory remotefilename copy sysreport tftp {hostname | ip-address} remotefilename} [start-date {day month | month day} year [end-date {day month | month day} year]] Syntax Description sysreport Generates and saves a report containing WAAS system information in a file.
Chapter 3 CLI Commands copy sysreport Device Modes application-accelerator central-manager Usage Guidelines The copy sysreport command consumes significant CPU and disk resources and can adversely affect system performance while it is running.
Chapter 3 CLI Commands copy system-status copy system-status To copy status information from the system for debugging, use the copy system-status EXEC command. copy system-status disk filename Syntax Description system-status Copies the system status to a disk file. disk filename Name of the file to be created on the disk. Defaults No default behaviors or values.
Chapter 3 CLI Commands copy tech-support copy tech-support To copy the configuration or image data from the system to use when working with Cisco TAC, use the copy tech-support EXEC command. copy tech-support {disk filename | ftp {hostname | ip-address} remotedirectory remotefilename | tftp {hostname | ip-address} remotefilename} Syntax Description tech-support Copies system information for technical support. disk filename Copies system information for technical support to a disk file.
Chapter 3 CLI Commands copy tech-support reload show running-config show startup-config wafs write Cisco Wide Area Application Services Command Reference OL-21611-01 3-49
Chapter 3 CLI Commands copy tftp copy tftp To copy configuration or image data from a TFTP server, use the copy tftp EXEC command. copy tftp disk {hostname | ip-address} remotefilename localfilename copy tftp running-config {hostname | ip-address} remotefilename copy tftp startup-config {hostname | ip-address} remotefilename Syntax Description tftp Copies an image from a TFTP server. disk Copies an image from a TFTP server to a disk file. hostname Hostname of the TFTP server.
Chapter 3 CLI Commands copy virtual-blade copy virtual-blade To copy software configuration or image data from a virtual blade disk image to an FTP server, use the copy virtual-blade EXEC command. copy virtual-blade vb_num disk vb_disk ftp {hostname | ip-address} remotefiledir remotefilename Syntax Description virtual-blade vb_num Specifies the virtual blade number of the virtual blade disk image to copy to.
Chapter 3 CLI Commands cpfile cpfile To make a copy of a file, use the cpfile EXEC command. cpfile oldfilename newfilename Syntax Description oldfilename Name of the file to copy. newfilename Name of the copy to be created. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines Only SYSFS files can be copied. Examples The following example shows how to create a copy of a file: WAE# cpfile fe512-194616.
Chapter 3 CLI Commands crypto delete crypto delete To remove SSL certificate and key files, use the crypto delete EXEC command. crypto delete {ca-certificate filename | pkcs12 {filename | admin }} Use the crypto delete EXEC command to remove a certificate from your WAE’s secure store. If you only want to disassociate a certificate from an accelerated service, use no server-cert-key in crypto ssl services accelerated-service mode.
Chapter 3 CLI Commands crypto export crypto export To export SSL certificate and key files, use the crypto export EXEC command. crypto export {ca-certificate filename | pkcs12 {factory-self-signed | admin | filename} {pem-cert-key | pem-cert-only | pem-key-only | pkcs12}}{disk pathname | ftp address | sftp address | terminal | tftp address} Syntax Description ca-certificate filename Export a certificate authority certificate file. pkcs12 Export a PKCS12 format file.
Chapter 3 CLI Commands crypto export crypto generate crypto import Cisco Wide Area Application Services Command Reference OL-21611-01 3-55
Chapter 3 CLI Commands crypto generate crypto generate To generate a self-signed certificate or a certificate signing request, use the crypt generate EXEC command. crypto generate {csr rsa modulus {1024 | 1536 | 2048 | 512 | 768}{disk pathname | ftp address | sftp address | terminal | tftp address} | self-signed-cert filename [exportable] rsa modulus {1024 | 1536 | 2048 | 512 | 768}} Syntax Description csr Generate a certificate signing request (CSR).
Chapter 3 CLI Commands crypto generate For some fields there will be a default value, If you enter '.', the field will be left blank. ----Country Name (2 letter code) [US]:US State or Province Name (full name) [California]: Locality Name (eg, city) [San Jose]:San Jose Organization Name (eg, company) [Cisco Systems]: Organizational Unit Name (eg, section) [ADBU]: Common Name (eg, YOUR name) [www.cisco.com]: Email Address [tac@cisco.com]: (Press Enter to accept the default.
Chapter 3 CLI Commands crypto import crypto import To import SSL certificates and key files, use the crypto import EXEC command. crypto import {ca-certificate filename | pkcs12 { filename | admin} [exportable]}{pem-cert-key | pkcs12}}{disk pathname | ftp address | sftp address | terminal | tftp address} Syntax Description ca-certificate filename Import a certificate authority certificate file. The name of the CA certificate file to be imported (PEM format) must have .ca extension.
Chapter 3 CLI Commands crypto import Note Examples DSA certificates and keys cannot be imported. The following example shows how to import a CA certificate file named mycert.ca from a TFTP server: WAE# crypto import ca-certificate mycert.ca tftp 00.00.00.
Chapter 3 CLI Commands crypto pki crypto pki To initialize the PKI managed store, use the crypto pki EXEC command. crypto pki managed-store initialize Syntax Description managed-store Specifies managed store commands. initialize Initializes the PKI managed store. Defaults No default behavior or values.
Chapter 3 CLI Commands debug aaa accounting debug aaa accounting To monitor and record AAA accounting debugging, use the debug aaa accounting EXEC command. To disable debugging, use the undebug form of this command. debug aaa accounting undebug aaa accounting Syntax Description aaa accounting Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator (Optional) Enables AAA accounting actions.
Chapter 3 CLI Commands debug aaa accounting • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command. Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module. We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.
Chapter 3 CLI Commands debug aaa authorization debug aaa authorization To monitor and record AAA authorization debugging, use the debug aaa authorization EXEC command. To disable debugging, use the undebug form of this command. debug aaa authorization undebug aaa authorization Syntax Description aaa authorization Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator (Optional) Enables AAA authorization actions.
Chapter 3 CLI Commands debug aaa authorization • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command. Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.
Chapter 3 CLI Commands debug accelerator debug accelerator To monitor and record accelerator debugging, use the debug accelerator EXEC command. To disable debugging, use the undebug form of this command.
Chapter 3 CLI Commands debug accelerator Defaults http Enables HTTP accelerator debugging. bypass-list Enables HTTP accelerator bypass list debugging. cli Enables configuration CLI debugging. conditional-response Enables HTTP accelerator metadata cache conditional response debugging. dre-hints Enables HTTP accelerator DRE hinting debugging. metadatacache Enables HTTP accelerator metadata cache debugging. redirect-response Enables HTTP accelerator metadata cache redirect response debugging.
Chapter 3 CLI Commands debug accelerator Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines The output associated with the debug accelerator name module command for an application accelerator is written to the file nameao-errorlog.current, where name is the accelerator name. The accelerator information manager debug output is written to the file aoim-errorlog.current.
Chapter 3 CLI Commands debug accelerator Related Commands show debugging Cisco Wide Area Application Services Command Reference 3-68 OL-21611-01
Chapter 3 CLI Commands debug all debug all To monitor and record all debugging, use the debug all EXEC command. To disable debugging, use the undebug form of this command. debug all undebug all Syntax Description all Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Enables all debugging.
Chapter 3 CLI Commands debug all • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command. Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module. We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.
Chapter 3 CLI Commands debug authentication debug authentication To monitor and record authentication debugging, use the debug authentication EXEC command. To disable debugging, use the undebug form of this command. debug authentication {content-request | user | windows-domain} undebug authentication {content-request | user | windows-domain} Syntax Description authentication (Optional) Enables authentication debugging. content-request Enables content request authentication debugging.
Chapter 3 CLI Commands debug authentication • For filtering on critical and error level debug messages, use the logging disk priority error global configuration command. • For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command. • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.
Chapter 3 CLI Commands debug buf debug buf To monitor and record buffer manager debugging, use the debug buf EXEC command. To disable debugging, use the undebug form of this command. debug buf {all | dmbuf | dmsg} undebug buf {all | dmbuf | dmsg} Syntax Description buf (Optional) Enables buffer manager debugging. all Enables all buffer manager debugging. dmbuf Enables only dmbuf debugging. dmsg Enables only dmsg debugging. Defaults No default behavior or values.
Chapter 3 CLI Commands debug buf • For filtering on critical and error level debug messages, use the logging disk priority error global configuration command. • For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command. • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.
Chapter 3 CLI Commands debug cdp debug cdp To monitor and record CDP debugging, use the debug cdp EXEC command. To disable debugging, use the undebug form of this command. debug cdp {adjacency | events | ip | packets} undebug cdp {adjacency | events | ip | packets} Syntax Description cdp (Optional) Enables CDP debugging. adjacency Enables CDP neighbor information debugging. events Enables CDP events debugging. ip Enables CDP IP debugging. packets Enables packet-related CDP debugging.
Chapter 3 CLI Commands debug cdp • For filtering on critical and error level debug messages, use the logging disk priority error global configuration command. • For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command. • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.
Chapter 3 CLI Commands debug cli debug cli To monitor and record CLI debugging, use the debug cli EXEC command. To disable debugging, use the undebug form of this command. debug cli {all | bin | parser} undebug cli {all | bin | parser} Syntax Description cli (Optional) Enables CLI debugging. all Enables all CLI debugging. bin Enables CLI command binary program debugging. parser Enables CLI command parser debugging. Defaults No default behavior or values.
Chapter 3 CLI Commands debug cli • For filtering on critical and error level debug messages, use the logging disk priority error global configuration command. • For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command. • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.
Chapter 3 CLI Commands debug cms debug cms To monitor and record CMS debugging, use the debug cms EXEC command. To disable debugging, use the undebug form of this command. debug cms undebug cms Syntax Description cms Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator (Optional) Enables CMS debugging.
Chapter 3 CLI Commands debug cms • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command. Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module. We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.
Chapter 3 CLI Commands debug dataserver debug dataserver To monitor and record data server debugging, use the debug dataserver EXEC command. To disable debugging, use the undebug form of this command. debug dataserver {all | clientlib | server} undebug dataserver {all | clientlib | server} Syntax Description dataserver (Optional) Enables data server debugging. all Enables all data server debugging. clientlib Enables data server client library module debugging.
Chapter 3 CLI Commands debug dataserver • For filtering on critical and error level debug messages, use the logging disk priority error global configuration command. • For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command. • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.
Chapter 3 CLI Commands debug dhcp debug dhcp To monitor and record DHCP debugging, use the debug dhcp EXEC command. To disable debugging, use the undebug form of this command. debug dhcp undebug dhcp Syntax Description dhcp Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator (Optional) Enables DHCP debugging.
Chapter 3 CLI Commands debug dhcp • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command. Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module. We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.
Chapter 3 CLI Commands debug dre debug dre To monitor and record DRE debugging, use the debug dre EXEC command. To disable debugging, use the undebug form of this command.
Chapter 3 CLI Commands debug dre If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).
Chapter 3 CLI Commands debug egress-method debug egress-method To monitor and record egress method debugging, use the debug egress-method EXEC command. To disable debugging, use the undebug form of this command. debug egress-method connection undebug egress-method connection Syntax Description eggress-method connection Defaults No default behavior or values.
Chapter 3 CLI Commands debug egress-method • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command. Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module. We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.
Chapter 3 CLI Commands debug emdb debug emdb To monitor and record embedded database debugging, use the debug emdb EXEC command. To disable debugging, use the undebug form of this command. debug emdb [level [levelnum]] undebug emdb [level [levelnum]] Syntax Description emdb (Optional) Enables embedded database debugging. level (Optional) Enables the specified debug level for EMDB service. levelnum (Optional) Debug level to disable. Level 0 disables debugging.
Chapter 3 CLI Commands debug emdb • For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command. • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.
Chapter 3 CLI Commands debug epm debug epm To monitor and record DCE-RPC EPM debugging, use the debug epm EXEC command. To disable debugging, use the undebug form of this command. debug epm undebug epm Syntax Description epm Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Usage Guidelines Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC.
Chapter 3 CLI Commands debug epm • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command. Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module. We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.
Chapter 3 CLI Commands debug flow debug flow To monitor and record network traffic flow debugging, use the debug flow EXEC command. To disable debugging, use the undebug form of this command. debug flow monitor tcpstat-v1 undebug flow monitor tcpstat-v1 Syntax Description flow (Optional) Enables network traffic flow debugging. monitor Enables monitor flow performance debugging commands. tcpstat-v1 Enables tcpstat-v1 debugging. Defaults No default behavior or values.
Chapter 3 CLI Commands debug flow • For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command. • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.
Chapter 3 CLI Commands debug generic-gre debug generic-gre To monitor and record generic GRE egress method debugging, use the debug generic-gre EXEC command. To disable debugging, use the undebug form of this command. debug generic-gre undebug generic-gre Syntax Description generic-gre Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator (Optional) Enables generic GRE egress method debugging.
Chapter 3 CLI Commands debug generic-gre • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command. Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module. We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.
Chapter 3 CLI Commands debug key-manager debug key-manager To monitor and record Central Manager key manager debugging, use the debug key-manager EXEC command. To disable debugging, use the undebug form of this command. debug key-manager undebug key-manager Syntax Description key-manager Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator (Optional) Enables the Central Manager key manager debugging.
Chapter 3 CLI Commands debug key-manager • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command. Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module. We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.
Chapter 3 CLI Commands debug logging debug logging To monitor and record logging debugging, use the debug logging EXEC command. To disable debugging, use the undebug form of this command. debug logging all undebug logging all Syntax Description logging (Optional) Enables logging debugging. all Enables all logging debugging. Defaults No default behavior or values.
Chapter 3 CLI Commands debug logging • For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command. • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.
Chapter 3 CLI Commands debug ntp debug ntp To monitor and record NTP debugging, use the debug ntp EXEC command. To disable debugging, use the undebug form of this command.( debug ntp undebug ntp Syntax Description ntp Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator (Optional) Enables NTP debugging.
Chapter 3 CLI Commands debug ntp • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command. Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module. We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.
Chapter 3 CLI Commands debug print-spooler debug print-spooler To monitor and record print spooler debugging, use the debug print-spooler EXEC command. To disable debugging, use the undebug form of this command. debug print-spooler {all | brief | errors | warnings} undebug print-spooler {all | brief | errors | warnings} Syntax Description print-spooler (Optional) Enables print spooler debugging. all Enables print spooler debugging using all debug features.
Chapter 3 CLI Commands debug print-spooler • For filtering on critical and error level debug messages, use the logging disk priority error global configuration command. • For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command. • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.
Chapter 3 CLI Commands debug rbcp debug rbcp To monitor and record RBCP debugging, use the debug rbcp EXEC command. To disable debugging, use the undebug form of this command. debug rbcp undebug rbcp Syntax Description rbcp Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Usage Guidelines Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC.
Chapter 3 CLI Commands debug rbcp • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command. Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module. We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.
Chapter 3 CLI Commands debug rpc debug rpc To monitor and record remote procedure calls (RPC) debugging, use the debug rpc EXEC command. To disable debugging, use the undebug form of this command. debug rpc undebug rpc {detail | trace} Syntax Description rpc Defaults No default behavior or values.
Chapter 3 CLI Commands debug rpc • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command. Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module. We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.
Chapter 3 CLI Commands debug snmp debug snmp To monitor and record SNMP debugging , use the debug snmp EXEC command. To disable debugging, use the undebug form of this command. debug snmp {all | cli | main | mib | traps} undebug snmp {all | cli | main | mib | traps} Syntax Description snmp (Optional) Enables SNMP debugging. all Enables all SNMP debug commands. cli Enables SNMP CLI debugging. main Enables SNMP main debugging. mib Enables SNMP MIB debugging. traps Enables SNMP trap debugging.
Chapter 3 CLI Commands debug snmp • For filtering on critical debug messages only, use the logging disk priority critical global configuration command. • For filtering on critical and error level debug messages, use the logging disk priority error global configuration command. • For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
Chapter 3 CLI Commands debug stats debug stats To monitor and record statistics debugging, use the debug stats EXEC command. To disable debugging, use the undebug form of this command. debug stats {all | collections | computation | history} undebug stats {all | collections | computation | history} Syntax Description stats (Optional) Enables statistics debugging. all Enables all statistics debug commands. collection Enables collection statistics debugging.
Chapter 3 CLI Commands debug stats • For filtering on critical and error level debug messages, use the logging disk priority error global configuration command. • For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command. • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.
Chapter 3 CLI Commands debug tfo debug tfo To monitor and record TFO flow optimization debugging, use the debug tfo EXEC command. To disable debugging, use the undebug form of this command.
Chapter 3 CLI Commands debug tfo The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current. The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.
Chapter 3 CLI Commands debug translog debug translog To monitor and record transaction logging debugging, use the debug translog EXEC command. To disable debugging, use the undebug form of this command. debug translog {detail | export | info} undebug translog export Syntax Description translog (Optional) Enables transaction logging debugging. detail Enables transaction log detailed debugging. export Enables transaction log FTP export debugging. info Enables transaction log high level debugging.
Chapter 3 CLI Commands debug translog • For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command. • For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.
Chapter 3 CLI Commands debug wafs debug wafs To set the log level of WAFS running components, use the debug wafs EXEC command. To disable debugging, use the undebug form of this command.
Chapter 3 CLI Commands debug wafs For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default. If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).
Chapter 3 CLI Commands debug wccp debug wccp To monitor and record WCCP information debugging, use the debug wccp EXEC command. To disable debugging, use the undebug form of this command. debug wccp {all | detail | error | events | keepalive | packets | slowstart} undebug wccp {all | detail | error | events | keepalive | packets | slowstart} Syntax Description wccp (Optional) Enables the WCCP information debugging. all Enables all WCCP debugging functions. detail Enables the WCCP detail debugging.
Chapter 3 CLI Commands debug wccp If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows: • For filtering on critical debug messages only, use the logging disk priority critical global configuration command. • For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
Chapter 3 CLI Commands delfile delfile To delete a file from the current directory, use the delfile EXEC command. delfile filename Syntax Description filename Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Name of the file to delete. central-manager Usage Guidelines Use the delfile EXEC command to remove a file from a SYSFS partition on the disk drive of the WAAS device.
Chapter 3 CLI Commands deltree deltree To remove a directory with all of its subdirectories and files, use the deltree EXEC command. deltree directory Syntax Description directory Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Name of the directory tree to delete. central-manager Usage Guidelines Note Examples Use the deltree EXEC command to remove a directory and all files within the directory from the WAAS SYSFS file system.
Chapter 3 CLI Commands dir dir To view details of one file or all files in a directory, use the dir EXEC command. dir [directory] Syntax Description directory Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator (Optional) Name of the directory to list. central-manager Usage Guidelines Use the dir EXEC command to view a detailed list of files contained within the working directory, including information about the file name, size, and time created.
Chapter 3 CLI Commands dir 4096 4096 4096 4096 92 4096 0 4096 Related Commands Thu Mon Sun Thu Wed Wed Wed Sun Apr Mar Apr Feb Apr Apr Apr Mar 6 6 16 16 12 12 12 19 12:13:50 14:14:41 23:36:40 11:51:51 20:23:20 20:23:43 20:23:41 18:47:29 2006 2006 2006 2006 2006 2006 2006 2006
actona apache emdb export ftp_export.status rpc_httpd snmpd.Chapter 3 CLI Commands disable disable To turn off privileged EXEC commands, use the disable EXEC command. disable Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines Use the WAAS software CLI EXEC mode for setting, viewing, and testing system operations. This command mode is divided into two access levels, user and privileged.
Chapter 3 CLI Commands disk disk To configure disks on a WAAS device, use the disk EXEC command. disk delete-partitions diskname disk delete-data-partitions disk disk-name diskxx replace disk insert diskname disk recreate-raid disk scan-errors diskname Syntax Description delete-partitions diskname Deletes data on the specified logical disk drive. After using this command, the WAAS software treats the specified disk drive as blank. All previous data on the drive is inaccessible.
Chapter 3 CLI Commands disk Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines The WAAS software supports hot-swap functionality for both failed disk replacement and scheduled disk maintenance. On the WAE-612 and WAE-7326, use the disk disk-name diskxx shutdown global configuration command to shut down a disk for scheduled disk maintenance. On the WAE-7341 and WAE-7371, use the disk disk-name diskxx replace EXEC command to shut down a disk.
Chapter 3 CLI Commands disk (config) disk logical shutdown show disks Cisco Wide Area Application Services Command Reference 3-128 OL-21611-01
Chapter 3 CLI Commands dnslookup dnslookup To resolve a host or domain name to an IP address, use the dnslookup EXEC command. dnslookup {hostname | domainname} Syntax Description hostname Name of DNS server on the network. domainname Name of domain. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples The following examples show how the dnslookup command is used to resolve the hostname myhost to IP address 172.31.69.11, abd.
Chapter 3 CLI Commands enable enable To access privileged EXEC commands, use the enable EXEC command. enable Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines Use the WAAS software CLI EXEC mode for setting, viewing, and testing system operations. This command mode is divided into two access levels: user and privileged.
Chapter 3 CLI Commands exit exit To terminate privileged-level EXEC mode and return to the user-level EXEC mode, use the exit command. exit Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes All modes Device Modes application-accelerator central-manager Usage Guidelines The exit EXEC command is equivalent to pressing Ctrl-Z or entering the end command.
Chapter 3 CLI Commands find-pattern find-pattern To search for a particular pattern in a file, use the find-pattern command in EXEC mode.
Chapter 3 CLI Commands find-pattern core.cache.3.0.0.b131.cnbuild.20016 -rw------1 admin root 97124352 Jan 11 13:26 /local/local1/core_dir/ core.cache.3.0.0.b131.cnbuild.8095 The following example shows how to search a file for a pattern and print the matching lines: WAE# find-pattern match 10 removed_core Tue Oct 12 10:30:03 UTC 2004 -rw------1 admin root 95600640 Oct 12 10:27 /local/local1/core_dir/ core.3.0.0.b5.eh.2796 -rw------1 admin root 101580800 Jan 11 12:01 /local/local1/core_dir/ core.cache.3.
Chapter 3 CLI Commands help help To obtain online help for the command-line interface, use the help EXEC command. help Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC and global configuration Device Modes application-accelerator central-manager Usage Guidelines You can obtain help at any point in a command by entering a question mark (?).
Chapter 3 CLI Commands install install To install a new software image (such as the WAAS software) into flash on the WAAS device, use the install EXEC command. install imagefilename Syntax Description imagefilename Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Name of the .bin file you want to install.
Chapter 3 CLI Commands install Related Commands copy disk reload Cisco Wide Area Application Services Command Reference 3-136 OL-21611-01
Chapter 3 CLI Commands less less To display a file using the Less application, use the less EXEC command. less file_name Syntax Description file_name Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Name of the file to be displayed. central-manager Usage Guidelines Examples Less is a pager application that displays text files one page at a time. You can use Less to view the contents of a file, but not edit it.
Chapter 3 CLI Commands license add license add To add a software license to a device, use the license add EXEC command. license add license-name Syntax Description license-name Name of the software license to add. The following license names are supported: • Transport—Enables basic DRE, TFO, and LZ optimization. • Enterprise—Enables the EPM, HTTP, MAPI, NFS, SSL, CIFS (WAFS), and Windows Print application accelerators, the WAAS Central Manager, and basic DRE, TFO, and LZ optimization.
Chapter 3 CLI Commands lls lls To view a long list of directory names, use the lls EXEC command. lls [directory] Syntax Description directory Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator (Optional) Name of the directory for which you want a long list of files.
Chapter 3 CLI Commands lls Related Commands dir lls ls Cisco Wide Area Application Services Command Reference 3-140 OL-21611-01
Chapter 3 CLI Commands ls ls To view a list of files or subdirectory names within a directory, use the ls EXEC command. ls [directory] Syntax Description directory Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator (Optional) Name of the directory for which you want a list of files. central-manager Usage Guidelines Use the ls directory command to list the filenames and subdirectories within a particular directory.
Chapter 3 CLI Commands ls pwd Cisco Wide Area Application Services Command Reference 3-142 OL-21611-01
Chapter 3 CLI Commands mkdir mkdir To create a directory, use the mkdir EXEC command. mkdir directory Syntax Description directory Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Name of the directory to create.
Chapter 3 CLI Commands mkfile mkfile To create a new file, use the mkfile EXEC command. mkfile filename Syntax Description filename Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Name of the file that you want to create. central-manager Usage Guidelines Use the mkfile EXEC command to create a new file in any directory of the WAAS device.
Chapter 3 CLI Commands ntpdate ntpdate To set the software clock (time and date) on a WAAS device using an NTP server, use the ntpdate EXEC command. ntpdate {hostname | ip-address} [key {authentication-key}] Syntax Description hostname NTP hostname. ip-address NTP server IP address. key (Optional) Specifies to use authentication with the NTP server. authentication-key Authentication key string to use with the NTP server authentication. This value must be between 0 and 4294967295.
Chapter 3 CLI Commands ping ping To send echo packets for diagnosing basic network connectivity on networks, use the ping EXEC command. ping {hostname | ip-address} Syntax Description hostname Hostname of system to ping. ip-address IP address of system to ping. Defaults No default behavior or values.
Chapter 3 CLI Commands pwd pwd To view the present working directory on a WAAS device, use the pwd EXEC command. pwd Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands reload reload To halt the operation and perform a cold restart on a WAAS device, use the reload EXEC command. reload [force | in m | cancel] Syntax Description force (Optional) Forces a reboot without further prompting. in m (Optional) Schedules a reboot after a specified interval (1-10080 minutes). cancel (Optional) Cancels a scheduled reboot. Defaults No default behavior or values.
Chapter 3 CLI Commands rename rename To rename a file on a WAAS device, use the rename EXEC command. rename oldfilename newfilename Syntax Description oldfilename Original filename. newfilename New filename. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines Use the rename command to rename any SYSFS file without making a copy of the file. Examples The following example shows how to rename the errlog.
Chapter 3 CLI Commands restore restore To restore the device to its manufactured default status by removing the user data from the disk and flash memory, use the restore EXEC command. restore {factory-default [preserve basic-config] | rollback} Syntax Description factory-default Resets the device configuration and data to their manufactured default status. preserve (Optional) Preserves certain configurations and data on the device. basic-config (Optional) Selects basic network configurations.
Chapter 3 CLI Commands restore By removing the WAAS Central Manager database, all configuration records for the entire WAAS network are deleted. If you do not have a valid backup file or a standby WAAS Central Manager, you must reregister every WAE with the WAAS Central Manager because all previously configured data is lost. If you used your standby WAAS Central Manager to store the database while you reconfigured the primary, you can register the former primary as a new standby WAAS Central Manager.
Chapter 3 CLI Commands restore WAE# show disks details Physical disk information: disk00: Normal disk01: Normal (h00 c00 i00 l00 - DAS) (h00 c00 i01 l00 - DAS) 140011MB(136.7GB) 140011MB(136.7GB) Mounted filesystems: MOUNT POINT / /swstore /state /disk00-04 /local/local1 ...
Chapter 3 CLI Commands restore WAE# reload ...... reloading ...... Because flash memory configurations were removed after the restore command was used, the show startup-config command does not return any flash memory data. The show running-config command returns the default running configurations.
Chapter 3 CLI Commands rmdir rmdir To delete a directory on a WAAS device, use the rmdir EXEC command. rmdir directory Syntax Description directory Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Name of the directory that you want to delete. central-manager Usage Guidelines Use the rmdir EXEC command to remove any directory from the WAAS file system. The rmdir command only removes empty directories.
Chapter 3 CLI Commands scp scp To copy files between network hosts, use the scp command. scp [4][6][B][C][p][q][r][v] [c cipher] [F config-file] [i id-file] [o ssh_option] [P port] [S program] [[user @] host : file] [...] [[user-n @] host-n : file-n] Syntax Description 4 (Optional) Forces this command to use only IPv4 addresses. 6 (Optional) Forces this command to use only IPv6 addresses. B (Optional) Specifies the batch mode. In this mode, the scp command does not ask for passwords or passphrases.
Chapter 3 CLI Commands scp Usage Guidelines The scp command uses SSH for transferring data between hosts. This command prompts you for passwords or pass phrases when needed for authentication.
Chapter 3 CLI Commands script script To execute a script provided by Cisco or check the script for errors, use the script EXEC command. script {check | execute} file_name Syntax Description check Checks the validity of the script. execute Executes the script. The script file must be a SYSFS file in the current directory. file_name Name of the script file. Defaults No default behavior or values.
Chapter 3 CLI Commands setup setup To configure basic configuration settings (general settings, device network settings, interception type, disk configuration, and licenses) on the WAAS device or to complete basic configuration after upgrading to the WAAS software, use the setup EXEC command. setup Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands show aaa accounting show aaa accounting To display the AAA accounting configuration information for a WAAS device, use the show aaa accounting EXEC command. show aaa accounting Defaults No default behavior or values.
Chapter 3 CLI Commands show aaa accounting Table 3-1 Related Commands Field Descriptions for the show aaa accounting Command (continued) Field Description wait-start WAAS device that sends both a start and a stop accounting record to the TACACS+ accounting server. The requested user service does not begin until the start accounting record is acknowledged. A stop accounting record is also sent. disabled Accounting that is disabled for the specified event.
Chapter 3 CLI Commands show aaa authorization show aaa authorization To display the AAA authorization configuration information for a WAAS device, use the show aaa authorization EXEC command. show aaa authorization Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines Use the show aaa authorizaiton EXEC command to display configuration and state information related to AAA authorization.
Chapter 3 CLI Commands show accelerator show accelerator To display the status and configuration of the application accelerators, use the show accelerator EXEC command. show accelerator [{cifs | detail | epm | http [debug]| mapi | nfs | ssl | video}] Syntax Description cifs (Optional) Displays the status for the CIFS application accelerator.
Chapter 3 CLI Commands show accelerator Table 3-3 Field Description for the show accelerator Command (continued) Field Description Policy Engine Config Item: Default Action Drop or Use. Specifies the action to be taken if the accelerator refuses to handle the connection (because of overload or other reasons). Drop means the connection is dropped, and Use means the connection uses a reduced set of policy actions (such as TFO and DRE). Policy Engine Config Item: Connection Limit Connection limit.
Chapter 3 CLI Commands show alarms show alarms To display information about various types of alarms, their status, and history on a WAAS device, use the show alarms EXEC command.
Chapter 3 CLI Commands show alarms • Node Health Manager (alarm overload condition) • System Monitor (sysmon) for disk failures The three levels of alarms in the WAAS software are as follows: • Critical—Alarms that affect the existing traffic through the WAE and are considered fatal (the WAE cannot recover and continue to process traffic). • Major—Alarms that indicate a major service (for example, the cache service) has been damaged or lost. Urgent action is necessary to restore this service.
Chapter 3 CLI Commands show alarms Table 3-5 Field Descriptions for the show alarms status Command Field Description Critical Alarms Number of critical alarms. Major Alarms Number of major alarms. Minor Alarms Number of minor alarms. Overall Alarm Status Aggregate status of alarms. Device is NOT in alarm overload state. Status of the device alarm overload state. Device enters alarm overload state @ 999 alarms/sec.
Chapter 3 CLI Commands show arp show arp To display the ARP table for a WAAS device, use the show arp EXEC command. show arp Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines Use the show arp command to display the Internet-to-Ethernet address translation tables of the Address Resolution Protocol.
Chapter 3 CLI Commands show authentication show authentication To display the authentication configuration for a WAAS device, use the show authentication EXEC command. show authentication {user | strict-password-policy | content-request} Syntax Descriptions user Displays authentication configuration for user login to the system. strict-password-policy Displays strict password policy configuration information.
Chapter 3 CLI Commands show authentication Examples Table 3-7 describes the fields shown in the show authentication user command display. Table 3-7 Field Descriptions for the show authentication user Command Field Description Login Authentication: Console/Telnet/Ftp/SSH Session Authentication service that is enabled for login authentication and the configured status of the service. Windows domain RADIUS Operation status of the authentication service. Values are enabled or disabled.
Chapter 3 CLI Commands show auto-discovery show auto-discovery To display Traffic Flow Optimization (TFO) auto-discovery information for a WAE, use the show auto-discovery EXEC command. show auto-discovery {blacklist [netmask netmask] | list [| {begin regex [regex] | exclude regex [regex] | include regex [regex]}]} Syntax Description blacklist Displays the entries in the blacklist server table. netmask netmask (Optional) Displays the network mask to filter the table output (A.B.C.D/).
Chapter 3 CLI Commands show auto-register show auto-register To display the status of the automatic registration feature on a WAE, use the show auto-register EXEC command. show auto-register Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Examples Table 3-10 describes the output in the show auto-register command display.
Chapter 3 CLI Commands show banner show banner To display the message of the day (MOTD), login, and EXEC banner settings, use the show banner EXEC command. show banner Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples Table 3-11 describes the fields shown in the show banner command display.
Chapter 3 CLI Commands show bypass show bypass To display static bypass configuration information for a WAE, use the show bypass EXEC command. show bypass list Syntax Description list Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Examples Table 3-12 describes the fields shown in the show bypass list command display. Table 3-12 Displays the bypass list entries. You can have a maximum of 50 entries.
Chapter 3 CLI Commands show cache http-metadatacache show cache http-metadatacache To display HTTP metadata cache information for a WAE, use the show cache http-metadatacache EXEC command. show cache http-metadatacache {all | conditional-response | redirect-response | unauthorized-response} [url] Syntax Description all Displays cache entries for all HTTP metadata cache response types. conditional-response Displays cache entries for conditional responses (304).
Chapter 3 CLI Commands show cache http-metadatacache Related Commands (config) accelerator http clear cache Cisco Wide Area Application Services Command Reference OL-21611-01 3-175
Chapter 3 CLI Commands show cdp show cdp To display CDP configuration information, use the show cdp EXEC command. show cdp entry {* | neighbor} [protocol | version] show cdp interface [GigabitEthernet slot/port | InlinePort slot/port/{lan/wan}] show cdp neighbors [detail | GigabitEthernet slot/port [detail] | InlinePort slot/port/{lan/wan}[detail]] show cdp {holdtime | run | timer | traffic} Syntax Description entry (Optional) Displays information for a specific CDP neighbor entry.
Chapter 3 CLI Commands show cdp Examples Table 3-14 describes the fields shown in the show cdp command display. Table 3-14 Field Descriptions for the show cdp Command Field Description Sending CDP packets Interval (in seconds) between transmissions of CDP advertisements. This field every XX seconds is controlled by the cdp timer command. Sending a holdtime value of XX seconds Time (in seconds) that the device directs the neighbor to hold a CDP advertisement before discarding it.
Chapter 3 CLI Commands show cdp Table 3-16 Field Descriptions for the show cdp entry protocol Command Field Description Protocol information for XX Name or identifier of the neighbor device. IP address IP address of the neighbor device. CLNS address Non-IP network address. The field depends on the type of neighbor. DECnet address Non-IP network address. The field depends on the type of neighbor. Table 3-17 describes the fields shown in the show cdp entry neighbor version command display.
Chapter 3 CLI Commands show cdp Table 3-20 describes the fields shown in the show cdp neighbors command display. Table 3-20 Field Descriptions for the show cdp neighbors Command Field Description Device ID Configured ID (name), MAC address, or serial number of the neighbor device. Local Intrfce (Local Interface) Protocol being used by the connectivity media. Holdtime Time, in seconds, that the current device will hold the CDP advertisement from a transmitting router before discarding it.
Chapter 3 CLI Commands show cdp Table 3-21 Field Descriptions for the show cdp neighbors detail Command (continued) Field Description VTP Management Domain VLAN trunk protocol management domain. The VLAN information is distributed to all switches that are part of the same domain. Native VLAN VLAN to which the neighbor interface belongs. Table 3-22 describes the field in the show cdp run command display. Table 3-22 Field Description for the show cdp run Command Field Description CDP is XX.
Chapter 3 CLI Commands show cdp Table 3-24 Related Commands Field Descriptions for the show cdp traffic Command (continued) Field Description CDP version 1 advertisements Output Number of CDP Version 1 advertisements sent by the local device. Input Number of CDP Version 1 advertisements received by the local device. CDP version 2 advertisements Output Number of CDP Version 2 advertisements sent by the local device. Input Number of CDP Version 2 advertisements received by the local device.
Chapter 3 CLI Commands show cifs show cifs To display legacy CIFS run-time information, use the show cifs EXEC command. show cifs auto-discovery [enabled | host-db | last] show cifs cache {disk-use | entry-count} show cifs connectivity peers show cifs mss show cifs requests {count | waiting} show cifs sessions {count | list} Syntax Description auto-discovery Displays the CIFS auto-discovery status and run-time data. enabled (Optional) Displays current state of CIFS auto-discovery.
Chapter 3 CLI Commands show cifs CIFS legacy mode is deprecated and no longer supported in WAAS 4.2.x and later. We recommend using the transparent CIFS accelerator instead. Use the show cifs cache command to view information about caching efficiency. You might use this command to determine if the cache contains sufficient space or if more space is needed. If you have a performance issue, you might use this command to see whether or not the cache is full.
Chapter 3 CLI Commands show clock show clock To display information about the system clock on a WAAS device, use the show clock EXEC command. show clock [detail | standard-timezones {all | details timezone | regions | zones region-name}] Syntax Description detail (Optional) Displays detailed information; indicates the clock source (NTP) and the current summer time setting (if any). standard-timezones (Optional) Displays information about the standard time zones.
Chapter 3 CLI Commands show clock Examples Table 3-25 describes the field in the show clock command display. Table 3-25 Field Description for the show clock Command Field Description Local time Day of the week, month, date, time (hh:mm:ss), and year in local time relative to the UTC offset. Table 3-26 describes the fields shown in the show clock detail command display.
Chapter 3 CLI Commands show cms show cms To display Centralized Management System (CMS) embedded database content and maintenance status and other information for a WAAS device, use the show cms EXEC command. show cms {database content {dump filename | text | xml} | info | secure-store} Syntax Description database Displays embedded database maintenance information. content Writes the database content to a file. dump filename Dumps all database content to a text file.
Chapter 3 CLI Commands show cms Table 3-27 Field Descriptions for the show cms info Command for WAAS Application Engines Field Description Status Connection status of the device to the Central Manager. This field may contain one of three values: online, offline, or pending. Time of last config-sync Time when the device management service last contacted the Central Manager for updates.
Chapter 3 CLI Commands show cms Table 3-29 describes the field in the show cms database content text command display. Table 3-29 Field Description for the show cms database content text Command Field Description Database content can be found in /local1/cms-db-12-12-2002-17:06:0 8:070.txt. Name and location of the database content text file. The show cms database content text command requests the management service to write its current configuration to an automatically generated file in text format.
Chapter 3 CLI Commands show cms secure-store show cms secure-store To display secure store status, use the show cms secure-store EXEC command. show cms secure-store Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands show crypto show crypto To display crypto layer information, use the show crypto EXEC command. show crypto {certificate-detail {factory-self-signed | management | admin | filename} | certificates | ssl services {accelerated-service service | host-service peering}} Syntax Description certificate-detail Displays a certificate in detail. factory-self-signed Displays WAAS self-signed certificates in detail. management Displays WAAS management certificates in detail.
Chapter 3 CLI Commands show crypto Table 3-32 Field Descriptions for the show crypto certificate-detail Command Field Description Subject Information on the holder of the certificate. Subject Public Key Info Public Key Algorithm RSA Public Key Fields display X.509 certificate information as defined in RFC 5280. Modulus Exponent X509v3 extensions X509v3 Subject Key Identifier Fields display X.509 certificate information as defined in X509v3 Authority Key Identifier RFC 5280.
Chapter 3 CLI Commands show debugging show debugging To display the state of each debugging option that was previously enabled on a WAAS device, use the show debugging EXEC command. show debugging Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines The show debugging command shows which debug options have been enabled or disabled.
Chapter 3 CLI Commands show device-id show device-id To display the device ID of a WAAS device, use the show device-id EXEC command. show device-id Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands show device-mode show device-mode To display the configured or current device mode of a WAAS device, use the show device-mode EXEC command. show device-mode {configured | current} Syntax Description configured Displays the configured device mode, which has not taken effect yet. current Displays the current device mode. Defaults No default behavior or values.
Chapter 3 CLI Commands show device-mode Table 3-35 describes the field in the show device-mode configured command display. Table 3-35 Related Commands Field Description for the show device-mode configured Command Field Description Configured device mode Device mode that has been configured, but has not yet taken effect.
Chapter 3 CLI Commands show directed-mode show directed-mode To view the status and port assigned to directed mode on a device, use the show directed-mode EXEC command. show directed-mode Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands show disks show disks To view information about the WAAS device disks, use the show disks EXEC command. show disks {details | failed-disk-id | failed-sectors [disk_name] | tech-support [details]} Syntax Description details Displays currently effective configurations with more details. failed-disk-id Displays a list of disk serial numbers that have been identified as failed. Note This option is not available on WAE-7341 and WAE-7371 models.
Chapter 3 CLI Commands show disks SMART support is vendor and drive technology (IDE, SCSI, and Serial Advanced Technology Attachment [SATA] disk drive) dependent. Each disk vendor has a different set of supported SMART attributes. Even though SMART attributes are vendor dependent there is a common way of interpreting most SMART attributes. Each SMART attribute has a normalized current value and a threshold value. When the current value exceeds the threshold value, the disk is considered to have “failed.
Chapter 3 CLI Commands show disks Table 3-37 Field Descriptions for the show disks details Command Field Description Physical disk information or RAID Physical disk information Lists the disks by number. On RAID-5 systems, this field is called RAID Physical disk information. disk00 Availability of the disk: Present, Not present or Not responding, Not used (*), or Online (for RAID-5 disks). Disk identification number and type, for example: (h00 c00i00 100 - DAS).
Chapter 3 CLI Commands show disks The following is sample output from the show disks tech-support command. The output shows that partition 04 and partition 05 on disks disk00 and disk01 are GOOD, and the RAIDed partitions /dev/md4 & /dev/md5 are in NORMAL OPERATION. However, the RAIDed partition /dev/md8 has an issue with one of the drives. Disk04 with partition 00 is GOOD, but the status shows ONE OR MORE DRIVES ABNORMAL because there is no pair on this partition.
Chapter 3 CLI Commands show disks Table 3-39 Field Descriptions for the show disks tech-support Command (RAID-5) Field Description Physical Slot Slot number. Installed memory Amount of memory for the disk. Copyback Status of whether copyback is enabled or disabled. Data scrubbing Status of whether data scrubbing is enabled or disabled. Defunct disk drive count Number of defunct disk drives.
Chapter 3 CLI Commands show disks Table 3-39 Field Descriptions for the show disks tech-support Command (RAID-5) Field Description Stripe-unit size Amount of data storage per stripe unit. The default is 256 KB per disk in the logical array. This parameter is not configurable. Stripe order (Channel,Device) Order in which data is striped across a group of physical drives that are grouped in a RAID array. Bad stripes Flag for bad stripes. Flag values are Yes or No.
Chapter 3 CLI Commands show disks Table 3-40 Field Descriptions for the show disks tech-support details Command (continued) Field Description Transport protocol Physical layer connector information, for example: Parallel SCSI (SPI-4). Local time is Day of the week, month, date, time hh:mm:ss, year, clock standard. For example, Mon Mar 19 23:33:12 2007 UTC. Device supports SMART and is Enabled Status of SMART support: Enabled or Disabled.
Chapter 3 CLI Commands show egress-methods show egress-methods To view the egress method that is configured and that is being used on a particular WAE, use the show egress-methods EXEC command. show egress-methods Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Examples Table 3-41 describes the fields shown in the show egress-methods command display.
Chapter 3 CLI Commands show filtering list show filtering list To display information about the incoming and outgoing TFO flows that the WAE currently has, use the show filtering list EXEC command. show filtering list [| {begin regex [regex] | exclude regex [regex] | include regex [regex] }] [| {begin regex [regex] | exclude regex [regex] | include regex [regex]}] Syntax Description list (Optional) Lists TCP flows that the WAE is currently optimizing or passing through. | (Optional) Output modifier.
Chapter 3 CLI Commands show filtering list 10.99.22.200:20 10.99.11.200:1417 10.99.22.200:1987 10.99.11.200:1438 10.99.22.200:1990 10.99.22.200:80 10.99.22.200:80 10.99.22.200:1985 10.99.22.200:80 10.99.22.200:80 10.99.22.200:80 10.0.19.5:54247 Note Related Commands 10.99.11.200:1417 10.99.22.200:20 10.99.11.200:80 10.99.22.200:5222 10.99.11.200:80 10.99.11.200:1426 10.99.11.200:1425 10.99.11.200:80 10.99.11.200:1410 10.99.11.200:1398 10.99.11.200:1392 10.1.242.
Chapter 3 CLI Commands show flash show flash To display the flash memory version and usage information for a WAAS device, use the show flash EXEC command. show flash Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples Table 3-42 describes the fields shown in the show flash command display.
Chapter 3 CLI Commands show hardware show hardware To display system hardware status for a WAAS device, use the show hardware EXEC command. show hardware Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands show hardware Table 3-43 Field Descriptions for the show hardware Command (continued) Field Description Total X CPU Number of CPUs on the device. XXXX Mbytes of Physical memory Number of megabytes of physical memory on the device. X CD ROM drive Number of CD-ROM drives on the device. X GigabitEthernet interfaces Number of Gigabit Ethernet interfaces on the device. X InlineGroup interfaces Number of InlineGroup interfaces on the device.
Chapter 3 CLI Commands show hardware Table 3-43 Field Descriptions for the show hardware Command (continued) Field Mount point Mount point for the file system. For example the mount point for SYSFS is /local/local1. Type Type of the file system. Values include root, internal, CONTENT, SYSFS, and PRINTSPOOL. Device Path to the partition on the disk. Size Total size of the file system in megabytes. Inuse Amount of disk space being used by the file system.
Chapter 3 CLI Commands show hosts show hosts To view the hosts on a WAAS device, use the show hosts EXEC command. show hosts Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines The show hosts command lists the name servers and their corresponding IP addresses.
Chapter 3 CLI Commands show inetd show inetd To display the status of TCP/IP services on a WAAS device, use the show inetd EXEC command. show inetd Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines The show inetd EXEC command displays the enabled or disabled status of TCP/IP services on the WAAS device.
Chapter 3 CLI Commands show interface show interface To display the hardware interface information for a WAAS device, use the show interface EXEC command. show interface {GigabitEthernet slot/port} | {ide control_num} | {InlineGroup slot/grpnumber} | {InlinePort slot/grpnumber/{lan | wan}} | {PortChannel port-num} | {scsi device_num} | {standby 1 } Syntax Description GigabitEthernet slot/port Displays the Gigabit Ethernet interface device information (only on suitably equipped systems).
Chapter 3 CLI Commands show interface Table 3-46 describes the fields shown in the show interface GigabitEthernet command display. Table 3-46 Field Descriptions for the show interface GigabitEthernet Command Field Description Description Description of the device, as configured by using the description option of the interface global configuration command. Type Type of interface. Always Ethernet. Ethernet address Layer-2 MAC address.
Chapter 3 CLI Commands show interface Table 3-47 Field Descriptions for the show interface InlinePort Command Field Description Device name Number identifier for this inlineport interface, such as eth0, eth1, and so forth. Packets Received Total number of packets received on this inlineport interface. Packets Intercepted Total number of packets intercepted. (Only TCP packets are intercepted.) Packets Bridged Number of packets that are bridged. Packets which are not intercepted are bridged.
Chapter 3 CLI Commands show interface Table 3-47 Field Descriptions for the show interface InlinePort Command (continued) Field Description Base address Base address. hexidecimal value. Flags Interface status indicators. Values include Up, Broadcast, Running, and Multicast. Link State Interface and link status. Mode Speed setting, transmission mode, and transmission speed for this interface. Table 3-48 describes the fields shown in the show interface PortChannel command display.
Chapter 3 CLI Commands show interface Table 3-49 describes the fields shown in the show interface standby command display. Table 3-49 Related Commands Field Descriptions for the show interface standby Command Field Description Description Description of the device, as configured by using the description option of the interface global configuration command. Interface Standby 1 Number that identifies the standby group and the number of associated physical interfaces.
Chapter 3 CLI Commands show inventory show inventory To display the system inventory information for a WAAS device, use the show inventory EXEC command. show inventory Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines The show inventory EXEC command allows you to view the UDI for a WAAS device.
Chapter 3 CLI Commands show ip access-list show ip access-list To display the access lists that are defined and applied to specific interfaces or applications on a WAAS device, use the show ip access-list EXEC command. show ip access-list [acl-name | acl-num] Syntax Description acl-name (Optional) Information for a specific access list, using an alphanumeric identifier up to 30 characters, beginning with a letter.
Chapter 3 CLI Commands show ip access-list Table 3-51 Field Descriptions for the show ip access-list Command (continued) Field Description Extended IP access list Name of a configured extended IP access list. Displays a list of the conditions configured for this list.
Chapter 3 CLI Commands show ip routes show ip routes To display the IP routing table for a WAAS device, use the show ip routes EXEC command. show ip routes Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines The show ip routes command displays the IP route table, which lists all of the different routes that are configured on the WAE.
Chapter 3 CLI Commands show kdump show kdump To display the kernel crash dump information for a WAAS device, use the show kdump EXEC command. show kdump Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples Table 3-53 describes the fields shown in the show kdump command display.
Chapter 3 CLI Commands show kerberos show kerberos To display the Kerberos authentication configuration for a WAAS device, use the show kerberos EXEC command. show kerberos Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples Table 3-54 describes the fields shown in the show kerberos command display.
Chapter 3 CLI Commands show key-manager show key-manager To display the key manager information for a WAAS device, use the show key-manager EXEC command. show key-manager {key-token | status} Syntax Description key-token Displays the encryption key token for each registered WAE device. status Displays the encryption status for each registered WAE device. Defaults No default behavior or values.
Chapter 3 CLI Commands show license show license To display license information for a WAAS device, use the show license EXEC command. show license Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples The following is sample output from the show license command.
Chapter 3 CLI Commands show logging show logging To display the system message log configuration for a WAAS device, use the show logging EXEC command. show logging Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines Use the system message log to view information about events that have occurred on a WAAS device. The syslog.
Chapter 3 CLI Commands show memory show memory To display memory blocks and statistics for a WAAS device, use the show memory EXEC command. show memory Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples Table 3-56 describes the fields shown in the show memory command display.
Chapter 3 CLI Commands show ntp show ntp To display the NTP parameters for a WAAS device, use the show ntp EXEC command. show ntp status Syntax Description status Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Displays NTP status. central-manager Examples Table 3-57 describes the fields shown in the show ntp status command display.
Chapter 3 CLI Commands show ntp Related Commands Table 3-57 Field Descriptions for the show ntp status Command (continued) Field Description offset Clock offset relative to the server. jitter Clock jitter.
Chapter 3 CLI Commands show peer optimization show peer optimization To display the configured serial peers for a WAAS device, use the show peer optimization EXEC command. show peer optimization Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands show policy-engine application show policy-engine application To display application policy information for a WAE, use the show policy-engine application EXEC command. show policy-engine application {classifier [app-classifier] | dynamic | name} Syntax Description classifier Displays information about the specified application classifier. If no classifier is specified, the show policy-engine applicaion command displays information about all classifiers.
Chapter 3 CLI Commands show policy-engine application Table 3-59 describes the fields shown in the show policy-engine application dynamic command display. Table 3-59 Field Descriptions for the show policy-engine application dynamic Command Field Description Dynamic Match Freelist Information Allocated Total number dynamic policies that can be allocated. In Use Number of dynamic matches that are currently in use.
Chapter 3 CLI Commands show policy-engine application Table 3-60 describes the fields shown in the show policy-engine application name command display. Table 3-60 Field Descriptions for the show policy-engine application name Command Field Description Number of Applications: X Number of applications defined on the WAE, including all of the default applications. WAAS includes over 150 default application policies.
Chapter 3 CLI Commands show policy-engine application Related Commands (config) policy-engine application classifier (config) policy-engine application map adaptor EPM (config) policy-engine application map adaptor WAFS transport (config) policy-engine application map basic (config) policy-engine application map other optimize DRE (config) policy-engine application map other optimize full (config) policy-engine application map other pass-through (config) policy-engine application name (config) policy-en
Chapter 3 CLI Commands show policy-engine status show policy-engine status To display high-level information about a WAE policy engine, use the show policy-engine status EXEC command. show policy-engine status Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands show policy-engine status (config) policy-engine application map adaptor EPM (config) policy-engine application map adaptor WAFS transport (config) policy-engine application map basic (config) policy-engine application map other optimize DRE (config) policy-engine application map other optimize full (config) policy-engine application map other pass-through (config) policy-engine application name (config) policy-engine config Cisco Wide Area Application Services Command Reference
Chapter 3 CLI Commands show print-services show print-services To display administrative users who have access to configuration privileges, legacy print services, or legacy print service processes on a WAAS device, use the show print-services EXEC command. show print-services {drivers user username | process} Syntax Description drivers Displays printer drivers on this print server. user username Specifies a username that belongs to the print admin group.
Chapter 3 CLI Commands show print-services Table 3-62 Field Descriptions for the show print-services process Command (continued) Field Description pid Process ID. Process identification number of the Samba process on the WAE Linux appliance. machine Machine name. Connected at Date and time of connection to the print server. No locked files Comment line. Print Spooler Status Related Commands scheduler is running Operation status of the print spooler scheduler.
Chapter 3 CLI Commands show processes show processes To display CPU or memory processes for a WAAS device, use the show processes EXEC command. show processes [cpu | debug pid | memory | system [delay secs | count num]] Syntax Description cpu (Optional) Displays CPU utilization. debug pid (Optional) Prints the system call and signal traces for a specified process identifier to display system progress. memory (Optional) Displays memory allocation processes.
Chapter 3 CLI Commands show processes Examples Table 3-63 describes the fields shown in the show processes command display. Table 3-63 Field Descriptions for the show processes Command Field Description CPU utilization CPU utilization since the last reload as a percentage for user, system overhead, and idle. Includes average usage (calculated every 10 minutes). Overall current CPU utilization Current CPU utilization over all CPUs in the system. PID Process identifier.
Chapter 3 CLI Commands show radius-server show radius-server To display RADIUS configuration information for a WAAS device, use the show radius-server EXEC command. show radius-server Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples Table 3-64 describes the fields shown in the show radius-server command display.
Chapter 3 CLI Commands show radius-server Related Commands (config) radius-server Cisco Wide Area Application Services Command Reference 3-242 OL-21611-01
Chapter 3 CLI Commands show running-config show running-config To display a WAAS device current running configuration on the terminal, use the show running-config EXEC command. The show running-config command replaces the write terminal command. show running-config [no-policy] Syntax Description no-policy Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator (Optional) Does not display policy engine configuration.
Chapter 3 CLI Commands show running-config copy startup-config Cisco Wide Area Application Services Command Reference 3-244 OL-21611-01
Chapter 3 CLI Commands show services show services To display services-related information for a WAAS device, use the show services EXEC command. show services {ports [port-num] | summary} Syntax Description ports Displays services by port number. port-num (Optional) Up to 8 port numbers (1–65535). summary Displays the services summary. Defaults No default behavior or values.
Chapter 3 CLI Commands show smb-conf show smb-conf To view the current values of the Samba configuration file, smb.conf, on a WAAS device, use the show smb-conf EXEC command. show smb-conf Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines The show smb-conf command displays the global, print$, and printers parameters values of the smb.
Chapter 3 CLI Commands show smb-conf cups options = "raw" force printername = yes lpq cache time = 0 log file = /local/local1/errorlog/samba.log max log size = 50 socket options = TCP_NODELAY SO_RCVBUF=8192 SO_SNDBUF=8192 smb ports = 50139 local master = no domain master = no preferred master = no dns proxy = no template homedir = /local/local1/ template shell = /admin-shell ldap ssl = start_tls comment = Comment: netbios name = MYFILEENGINE realm = ABC wins server = 10.10.10.1 password server = 10.10.10.
Chapter 3 CLI Commands show snmp show snmp To check the status of SNMP communications for a WAAS device, use the show snmp EXEC command. show snmp {alarm-history | engineID | event | group | stats | user} Syntax Description alarm-history Displays SNMP alarm history information. engineID Displays local SNMP engine identifier. event Displays events configured through the Event MIB. Applies only to application-accelerator device mode. group Displays SNMP groups. stats Displays SNMP statistics.
Chapter 3 CLI Commands show snmp Table 3-66 summarizes the mapping of module names to module IDs. Table 3-66 Summary of Module Names to ID Numbers Module Name Module ID AD_DATABASE 8000 NHM 1 NHM/NHM 2500 nodemgr 2000 standby 4000 sysmon 1000 UNICAST_DATA_RECEIVER 5000 UNICAST_DATA_SENDER 6000 Table 3-67 summarizes the mapping of category names to category IDs.
Chapter 3 CLI Commands show snmp Table 3-69 Field Descriptions for the show snmp event Command (continued) Field Description (1): Name for the trigger. This name is locally-unique and administratively assigned. For example, this field might contain the “isValid” trigger name. Numbering indicates that this is the first management trigger listed in the show output. Comment: Description of the trigger function and use. For example: WAFS license file is not valid.
Chapter 3 CLI Commands show snmp Table 3-69 Field Descriptions for the show snmp event Command (continued) Field Description Cmp: Comparison. Type of boolean comparison to perform. The numbers 1–6 correspond to these Boolean comparisons: unequal (1) equal (2) less (3) lessOrEqual (4) greater (5) greaterOrEqual (6) Start: Starting value for which this instance will be triggered. ObjOwn: Object owner. Obj: Object. EveOwn: Event owner. Eve: Event. Type of SNMP event. For example: CLI_EVENT.
Chapter 3 CLI Commands show snmp Table 3-71 Field Descriptions for the show snmp stats Command Field Description SNMP packets input Total number of SNMP packets input. Bad SNMP version errors Number of packets with an invalid SNMP version. Unknown community name Number of SNMP packets with an unknown community name. Illegal operation for community name supplied Number of packets requesting an operation not allowed for that community.
Chapter 3 CLI Commands show snmp (config) snmp-server group (config) snmp-server host (config) snmp-server location (config) snmp-server mib (config) snmp-server notify inform (config) snmp-server user (config) snmp-server view snmp trigger Cisco Wide Area Application Services Command Reference OL-21611-01 3-253
Chapter 3 CLI Commands show ssh show ssh To display the status and configuration information of the Secure Shell (SSH) service for a WAAS device, use the show ssh EXEC command. show ssh Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples Table 3-73 describes the fields shown in the show ssh command display.
Chapter 3 CLI Commands show startup-config show startup-config To display the startup configuration for a WAAS device, use the show startup-config EXEC command. show startup-config Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines Use this EXEC command to display the configuration used during an initial bootup, stored in NVRAM.
Chapter 3 CLI Commands show startup-config Related Commands configure copy running-config show running-config Cisco Wide Area Application Services Command Reference 3-256 OL-21611-01
Chapter 3 CLI Commands show statistics accelerator show statistics accelerator To display application accelerator general statistics for a WAAS device, use the show statistics accelerator EXEC command.
Chapter 3 CLI Commands show statistics accelerator Usage Guidelines Using the show statistics accelerator command with no options displays a summary of the statistical information for all application accelerators. To obtain detailed statistics for an application accelerator, use the command options to filter the results. Examples Table 3-74 describes the fields shown in the show statistics accelerator cifs command display.
Chapter 3 CLI Commands show statistics accelerator Table 3-74 Field Descriptions for the show statistics accelerator cifs Command (continued) Field Description Last registration occurred Amount of time since the accelerator application registered with the Policy Engine (seconds).
Chapter 3 CLI Commands show statistics accelerator Table 3-74 Field Descriptions for the show statistics accelerator cifs Command (continued) Field Description Accept queue add failures Number of connections that could not be added to the accelerator connection accept queue due to a failure. The failure could possibly be due to the accelerator not being present, or a queue overflow.
Chapter 3 CLI Commands show statistics accelerator Table 3-76 Field Descriptions for the show statistics accelerator generic Command Field Description Time elapsed since "clear statistics" Time that has elapsed since the statistics were last reset. Time Accelerator was started Local time accelerator was started or restarted.
Chapter 3 CLI Commands show statistics accelerator Table 3-76 Field Descriptions for the show statistics accelerator generic Command (continued) Field Description Total number of connections handled Connections handled since the accelerator was started or its statistics last reset. Incremented when a connection is accepted or reused. Never decremented. This value will always be greater than or equal to the Current Active Connections statistic.
Chapter 3 CLI Commands show statistics accelerator Table 3-76 Field Descriptions for the show statistics accelerator generic Command (continued) Field Description Drops Number of hits that attempted use of the accelerator application but were rejected for some reason. A separate hit and drop will be tallied for each TCP SYN packet received for a connection. This includes the original SYN and any retries.
Chapter 3 CLI Commands show statistics accelerator Table 3-77 Field Descriptions for the show statistics accelerator http detail Command Field Description Total Handled Connections Connections handled since the accelerator was started or its statistics last reset. Incremented when a connection is accepted or reused. Never decremented. This value will always be greater than or equal to the Current Active Connections statistic.
Chapter 3 CLI Commands show statistics accelerator Table 3-77 Field Descriptions for the show statistics accelerator http detail Command Field Description Total Connections Handed-off Total Pushed Down Connections + Total Connections Handed-off with Compression Policies Disabled. Total Connections Handed-off with Compression Policies Disabled Total number of connections handed off to generic optimization with compression policies disabled.
Chapter 3 CLI Commands show statistics accelerator Table 3-77 Field Descriptions for the show statistics accelerator http detail Command Field Description Total Locally Served Redirect Responses Number of locally served redirect (301) responses. Total Locally Served Unauthorized Responses Number of locally served authentication required (401) responses. Total Locally Served Conditional Responses Number of locally served conditional (304) responses.
Chapter 3 CLI Commands show statistics accelerator Table 3-77 Field Descriptions for the show statistics accelerator http detail Command Field Description Last registration occurred The amount of time since the accelerator application registered with the Policy Engine (seconds).
Chapter 3 CLI Commands show statistics accelerator Table 3-77 Field Descriptions for the show statistics accelerator http detail Command Field Rejected Connection Counts Due To: (Total:) Description • The number of all of the reject reasons that represent hits that were not able to use the accelerator applications.
Chapter 3 CLI Commands show statistics accelerator Table 3-78 Field Descriptions for the show statistics accelerator mapi detail Command Field Description Global Statistics Time Accelerator was started Time that the accelerator was started. Time statistics were Last Reset/Cleared Time that the statistics were last reset. Total Handled Connections Number of connections handled since the accelerator was started.
Chapter 3 CLI Commands show statistics accelerator Table 3-78 Field Descriptions for the show statistics accelerator mapi detail Command Field Description Average Accumulated Read Ahead Data Size (bytes) Average data size for MAPI read ahead. Local Response Count Number of local MAPI command responses sent to the client without waiting for a response from the peer WAE. Average Local Response Time (usec) Average time used for local responses, in microseconds.
Chapter 3 CLI Commands show statistics accelerator Table 3-78 Field Descriptions for the show statistics accelerator mapi detail Command Field Description Total RopBackOff Duration (msec) Cumulative time of ropbackoff durations across all connections, in milliseconds. Total Wait Time Of Requests Queued Due To FlowControl (msec) Cumulative wait time of requests queued due to flow control across all connections, in milliseconds.
Chapter 3 CLI Commands show statistics accelerator Table 3-78 Field Descriptions for the show statistics accelerator mapi detail Command Field Description Current Reserved (Unused) Connections Number of current reserved but still not used connections. Average In-Use Connections in Last One Hour Average number of average in-use connections in the last hour. This number is zero if statistics were reset/cleared within one hour.
Chapter 3 CLI Commands show statistics accelerator Table 3-78 Field Descriptions for the show statistics accelerator mapi detail Command Field Description Completed Connections Number of hits that have made use of the accelerator application and have completed. Drops Number of hits that attempted use of the accelerator application but were rejected for some reason. A separate hit and drop will be tallied for each TCP SYN packet received for a connection.
Chapter 3 CLI Commands show statistics accelerator Table 3-78 Field Descriptions for the show statistics accelerator mapi detail Command Field Description Accept queue add failures Number of connections that could not be added to the accelerator connection accept queue due to a failure. The failure could possibly be due to accelerator not being present, or a queue overflow.
Chapter 3 CLI Commands show statistics accelerator Table 3-79 Field Descriptions for the show statistics accelerator nfs detail Command (continued) Field Description Total Local Replies Number of requests that resulted in WAAS generating a local reply. Percentage of Requests Served Locally Percentage of requests served locally by the WAAS device. Percentage of Requests Served Remotely Percentage of requests served remotely by the NFS server.
Chapter 3 CLI Commands show statistics accelerator Table 3-79 Field Descriptions for the show statistics accelerator nfs detail Command (continued) Field Description Updated Released Number of hits that were released during Auto-Discovery and did not make use of the accelerator application. Active Connections Number of hits that represent either active connections using the accelerator application or connections that are still in the process of performing Auto-Discovery.
Chapter 3 CLI Commands show statistics accelerator Table 3-79 Field Descriptions for the show statistics accelerator nfs detail Command (continued) Field Description AO discovery successful For the accelerators that work in dual-ended mode, accelerator discovery (as part of auto discovery) is performed. This counter indicates the number of times accelerator discovery was successful. AO discovery failure The number of times accelerator discovery failed.
Chapter 3 CLI Commands show statistics accelerator Table 3-80 Field Descriptions for the show statistics accelerator ssl detail Command (continued) Field Description Total Dropped Connections The number of connections that the SSL accelerator ended prematurely. This could be due to verification failures, revocation check failures, errors detected during the handshake or data transfer phase of the connection, or due to internal errors.
Chapter 3 CLI Commands show statistics accelerator Table 3-80 Field Descriptions for the show statistics accelerator ssl detail Command (continued) Field Description Total Accelerator Bytes Written An SSL accelerator internal counter. (Bytes written to original side of DRE). Total Accelerator Writes An SSL accelerator internal counter. (Write operations performed on original side of DRE). Total DRE Bytes Read An SSL accelerator internal counter. (Bytes read from optimized side of DRE).
Chapter 3 CLI Commands show statistics accelerator Table 3-80 Field Descriptions for the show statistics accelerator ssl detail Command (continued) Field Description Total renegotiations requested by server The number of SSL “Hello Request” messages detected by the SSL accelerator. Total SSL renegotiations performed The number of SSL renegotiation attempts (successful and unsuccessful) detected by the SSL accelerator.
Chapter 3 CLI Commands show statistics accelerator Table 3-80 Field Descriptions for the show statistics accelerator ssl detail Command (continued) Field Description [C2S-Srvr] Number of sessions timedout The number of sessions in the client-facing session cache that were not reused because they were timed out. [C2S-Srvr] Number of sessions deleted because of cache full The number of sessions evicted from the client-facing session cache to make room for new sessions.
Chapter 3 CLI Commands show statistics accelerator Table 3-80 Field Descriptions for the show statistics accelerator ssl detail Command (continued) Field Description Failed Certificate Verifications (non OCSP) The number of certificate verification attempts deemed unsuccessful based on results of the certificate verification operation. Total Failed Certificate Verifications due to The number of certificate verification failures due to Other Errors other problems (including internal errors).
Chapter 3 CLI Commands show statistics accelerator Table 3-80 Field Descriptions for the show statistics accelerator ssl detail Command (continued) Field Description Flows dropped due to revocation check The number of connections dropped by this WAE because revocation check of the client or server certificate failed.
Chapter 3 CLI Commands show statistics accelerator Table 3-81 Field Descriptions for the show statistics accelerator video detail Command Field Description Max stream bitrate overload Number of unaccelerated connections due to stream bit-rate overload. Max aggregate bitrate overload Number of unaccelerated connections due to aggregate bit-rate overload. Max concurrent sessions overload Number of unaccelerated connections due to client session overload.
Chapter 3 CLI Commands show statistics accelerator Table 3-81 Field Descriptions for the show statistics accelerator video detail Command Field Description Last registration occurred The amount of time since the accelerator application registered with the Policy Engine (seconds).
Chapter 3 CLI Commands show statistics accelerator Table 3-81 Field Descriptions for the show statistics accelerator video detail Command Field Rejected Connection Counts Due To: (Total:) Description • The number of all of the reject reasons that represent hits that were not able to use the accelerator applications.
Chapter 3 CLI Commands show statistics aoim show statistics aoim To display AO (accelerator) Information Manager statistics for a WAAS device, use the show statistics aoim EXEC command. show statistics aoim [local | peer | detail] Syntax Description aoim Displays statistics for the AO Information Manager for all local application accelerators and all known peers. local Displays statistics only for all locally registered application accelerators.
Chapter 3 CLI Commands show statistics aoim Table 3-82 Field Descriptions for the show statistics aoim Command (continued) Field Description Number of Peers Number of known or encountered peer WAAS devices. Number of Local AOs Number of application accelerators registered on this WAAS device. Total # of AO Handoffs Number of application accelerators invoked to handle a connection once a & Inserts peer synchronization has completed. AO Name of the locally registered application accelerator.
Chapter 3 CLI Commands show statistics aoim Table 3-82 Field Descriptions for the show statistics aoim Command (continued) Field Description Session timeouts The number of times the accelerator application did not issue a keepalive to the Policy Engine in a timely manner. A session refers to the particular registration of the accelerator application within the Policy Engine.
Chapter 3 CLI Commands show statistics aoim Table 3-82 Field Descriptions for the show statistics aoim Command (continued) Field Rejected Connection Counts Due To: (Total:) Description • The number of all of the reject reasons that represent hits that were not able to use the accelerator applications.
Chapter 3 CLI Commands show statistics application show statistics application To view the performance statistics for applications running on your WAAS device, use the show statistics application EXEC command. show statistics application [app_name | savings app_name] Syntax Description app_name Displays the statistics for the name of the application. savings app_name Displays savings statistics for the name of the application. Defaults No default behavior or values.
Chapter 3 CLI Commands show statistics application Table 3-84 Statistic Descriptions for the show statistics application Command Statistic Description Internal Client Traffic initiated by the WAE device Internal Server Traffic terminated by the WAE device Opt Preposition Optimized traffic on the WAN side, initiated by the WAE device for preposition purposes Opt TCP Only Optimized traffic on the WAN side, optimized at the TFO level only Opt TCP Plus Optimized traffic on the WAN side, optimize
Chapter 3 CLI Commands show statistics application Related Commands show statistics Cisco Wide Area Application Services Command Reference OL-21611-01 3-293
Chapter 3 CLI Commands show statistics authentication show statistics authentication To display authentication statistics for a WAAS device, use the show statistics authentication EXEC command. show statistics authentication Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands show statistics auto-discovery show statistics auto-discovery To display Traffic Flow Optimization (TFO) auto-discovery statistics for a WAE, use the show statistics auto-discovery EXEC command. show statistics auto-discovery [blacklist] Syntax Description blacklist Defaults No default behavior or values.
Chapter 3 CLI Commands show statistics auto-discovery Table 3-86 Result Value Descriptions for the show statistics auto-discovery Command Result Description Socket Allocation failures Number of socket allocations that failed. Accept pair allocation failures Number of socket pair allocations that failed. Unix allocation failures Number of Unix socket allocations that failed. Connect lookup failures Number of socket connection lookups that failed.
Chapter 3 CLI Commands show statistics auto-discovery Table 3-86 Result Value Descriptions for the show statistics auto-discovery Command Result AOIM Sync with Peer still in progress Description Auto-discovery failed because AOIM synchronization is still in progress between the peers. Auto discovery success TO Internal server The address of the internal server. External server The address of the external server. Auto discovery success FOR Internal client The address of the internal client.
Chapter 3 CLI Commands show statistics cifs show statistics cifs To display the CIFS statistics information, use the show statistics cifs EXEC command. show statistics cifs {cache details | requests} Syntax Description cache details Statistics for the CIFS cache. requests Statistics for CIFS requests. Defaults No default behavior or values.
Chapter 3 CLI Commands show statistics cifs Table 3-87 Field Descriptions for the show statistics cifs requests Command (continued) Field Related Commands Description remote Number of remote requests for this command. async Number of async requests for this command. avg local Average local request time in milliseconds for this command. avg remote Average remote request time in milliseconds for this command. NB_SESSION_REQ NetBIOS session request command.
Chapter 3 CLI Commands show statistics connection show statistics connection To display all connection statistics for a WAAS device, use the show statistics connection EXEC command.
Chapter 3 CLI Commands show statistics connection Table 3-88 Field Descriptions for the show statistics connection Command Field Description Current Active Optimized Flows Number of current active optimized TCP connections of all types. Current Active Optimized TCP Plus Flows Number of current active connections using DRE/LZ optimization or handled by an accelerator. Current Active Optimized TCP Only Number of current active connections using TFO optimization Flows only.
Chapter 3 CLI Commands show statistics connection Table 3-89 Connection Types ConnType Description App Dyn Mtch Optimized The connection has been forced through an application dynamic match to be optimized, even though the connection may be handled as pass-through. PT AD Int Error The connection encountered an internal error during processing by the TFO auto discovery SYN cache. PT App Cfg The policy action for this application is configured as pass-through.
Chapter 3 CLI Commands show statistics connection Related Commands clear arp-cache show statistics accelerator show statistics connection egress-methods Cisco Wide Area Application Services Command Reference OL-21611-01 3-303
Chapter 3 CLI Commands show statistics connection auto-discovery show statistics connection auto-discovery To display auto-discovery connection statistics for a WAAS device, use the show statistics connection auto-discovery EXEC command.
Chapter 3 CLI Commands show statistics connection auto-discovery Table 3-90 Field Descriptions for the show statistics connection auto-discovery Command Field Description Current Active Optimized Flows Number of current active optimized TCP connections of all types. Current Active Optimized TCP Plus Flows Number of current active connections using DRE/LZ optimization or handled by an accelerator.
Chapter 3 CLI Commands show statistics connection closed show statistics connection closed To display closed connection statistics for a WAAS device, use the show statistics connection closed EXEC command.
Chapter 3 CLI Commands show statistics connection closed Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Usage Guidelines Using the show statistics connection closed command with no options displays a summary of the closed TCP connections on the WAE. To obtain detailed statistics for a connection, use the command options to filter the connection.
Chapter 3 CLI Commands show statistics connection closed show statistics connection egress-methods Cisco Wide Area Application Services Command Reference 3-308 OL-21611-01
Chapter 3 CLI Commands show statistics connection conn-id show statistics connection conn-id To display connection ID statistics for a WAAS device, use the show statistics connection conn-id EXEC command. show statistics connection conn-id connection_id Syntax Description conn-id connection_id Defaults No default behavior or values.
Chapter 3 CLI Commands show statistics connection conn-id Table 3-92 Field Descriptions for the show statistics connection conn-id Command (continued) Field Description Policy Details: Configured Name of the configured application policy. Policy Details: Derived Named of the derived application policy. Policy Details: Peer Name of the application policy on the peer side. Policy Details: Negotiated Name of the negotiated application acceleration policy.
Chapter 3 CLI Commands show statistics connection conn-id Table 3-92 Related Commands Field Descriptions for the show statistics connection conn-id Command (continued) Field Description Policy Policy in use on connection. EOT State [write | req | ack | read | ack] End of transmission state for data written and read. Socket States Socket states, including read-shut, write-shut, close, choke, and envoy.
Chapter 3 CLI Commands show statistics connection egress-methods show statistics connection egress-methods To display detailed egress method-related information about the connection segments for a WAE, use the show statistics connection egress-methods EXEC command.
Chapter 3 CLI Commands show statistics connection egress-methods • One connection tuple to represent the Client—Edge segment • One connection tuple to represent the Edge—Core segment In the show output, these two connection tuples appear as TUPLE and MATE. (See Table 3-93.) The important information to view is the local and remote IP address of the connection tuple and not whether it is marked as TUPLE or MATE.
Chapter 3 CLI Commands show statistics connection egress-methods Table 3-93 Field Descriptions for the show tfo egress-methods connection Command Field Description TUPLE Client-IP:Port IP address and port number of the client device in the connection tuple. Server-IP:Port IP address and port number of the server device in the connection tuple. MATE Client-IP:Port IP address and port number of the client device in the mate connection tuple.
Chapter 3 CLI Commands show statistics connection egress-methods a reverse ARP lookup and is then recorded, also. When packets egress the connection tuple in this scenario, they will have a GRE header with the destination IP address of the intercepting device that was recorded. The updates count may be greater than 1 in certain topologies.
Chapter 3 CLI Commands show statistics connection optimized show statistics connection optimized To display optimized connection statistics for a WAAS device, use the show statistics connection optimized EXEC command.
Chapter 3 CLI Commands show statistics connection optimized all (Optional) Displays all the connection statistics for connections of the filtered type. savings (Optional) Displays the savings connection statistics for connections of the filtered type. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Usage Guidelines The show statistics connection optimized command displays the statistics for optimized TCP connections.
Chapter 3 CLI Commands show statistics connection optimized Table 3-94 Related Commands Field Descriptions for the show statistics connection optimized Command Field Description PeerID The MAC address of the peer device. Accel Types of acceleration in use on the connection.
Chapter 3 CLI Commands show statistics connection pass-through show statistics connection pass-through To display pass through connection statistics for a WAAS device, use the show statistics connection pass-through EXEC command. show statistics connection pass-through client-ip {ip_address | hostname} | client-port port | peer-id peer_id | server-ip {ip_address | hostname} | server-port port Syntax Description pass-through (Optional) Displays active connection statistics for pass-through connections.
Chapter 3 CLI Commands show statistics connection pass-through Table 3-95 Field Descriptions for the show statistics connection pass-through Command Field Description Current Active Optimized Flows Number of current active optimized TCP connections of all types. Current Active Optimized TCP Plus Flows Number of current active connections using DRE/LZ optimization or handled by an accelerator. Current Active Optimized TCP Only Number of current active connections using TFO optimization Flows only.
Chapter 3 CLI Commands show statistics crypto ssl ciphers show statistics crypto ssl ciphers To display crypto SSL cipher usage statistics, use the show statistics crypto ssl ciphers EXEC command. show statistics crypto ssl ciphers Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands show statistics datamover show statistics datamover To display statistics about the internal datamover component, use the show statistics datamover EXEC command. show statistics datamover Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Usage Guidelines The show statistics datamover command displays the statistics for the internal datamover component.
Chapter 3 CLI Commands show statistics datamover Table 3-97 Field Descriptions for the show statistics datamover Command (continued) Field Description 32 . . . 2048 byte areas used Number of storage areas of each size. Zone pages used Number of pages used for the 32-2048 byte storage areas. Non-zone pages used Number of pages used for page mapping. Cloned identifiers Number of cloned identifiers. Number of lookup stalls Number of lookup stalls.
Chapter 3 CLI Commands show statistics directed-mode show statistics directed-mode To directed mode statistics for a device, use the show statistics directed-mode EXEC command. show statistics directed-mode Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Examples Table 3-98 describes the fields shown in the show statistics directed-mode command display.
Chapter 3 CLI Commands show statistics dre show statistics dre To display Data Redundancy Elimination (DRE) general statistics for a WAE, use the show statistics dre EXEC command, show statistics dre [detail] Syntax Description detail Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Examples Table 3-99 describes the fields shown in the show statistics dre command display. This command shows the aggregated statistics for all connections.
Chapter 3 CLI Commands show statistics dre Table 3-99 Field Descriptions for the show statistics dre Command Field Description Optimized size Object buffer size Number Lowmem Errors Open Decode Malloc PLZ-off MinRes Chunk aggregation node memory consumption Open Persistent LZ Disk activity ratio max used RAM size Score Encode Overall: msg, in, out, ratio All messages coming to DRE components. Number of messages, input bytes, output bytes, compression ratio (in less out, divided by in).
Chapter 3 CLI Commands show statistics dre Table 3-99 Field Descriptions for the show statistics dre Command Field Related Commands Description DRE: msg, in, out, ratio All messages handled by DRE compression. Number of DRE compressed messages, input bytes, output bytes, compression ratio (in less out, divided by in). LZ: msg, in, out, ratio Number of messages bypassed by DRE. Number of messages, number of bytes. LZ: bypass: msg, in All messages handled by LZ.
Chapter 3 CLI Commands show statistics filtering show statistics filtering To display statistics about the incoming and outgoing TFO flows that the WAE currently has, use the show statistics filtering EXEC command. show statistics filtering Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands show statistics filtering Table 3-100 Field Descriptions for the show statistics filtering Command Field Description Syn packets received and dropped on estab. conn Number of syn packets received for a connection that was in established state. In established state, the syn packet is invalid and is dropped. Syn-Ack packets received and dropped Number of syn-ack packets received on a connection that on estab. conn was in established state.
Chapter 3 CLI Commands show statistics filtering Table 3-100 Field Descriptions for the show statistics filtering Command Field Description Internal Server conn. not optimized due Number of server connections not optimized because this to Serial Peer device is in a serial cluster and is passing through the connections to its serial peer.
Chapter 3 CLI Commands show statistics flow show statistics flow To display flow statistics for a WAAS device, use the show statistics flow EXEC command. show statistics flow {filters | monitor tcpstat-v1} Syntax Description filters Displays flow filter statistics. monitor Displays flow performance statistics. tcpstat-v1 Displays tcpstat-v1 collector statistics. Defaults No default behavior or values.
Chapter 3 CLI Commands show statistics flow Table 3-102 describes the fields shown in the show statistics flow monitor command display. Table 3-102 Field Descriptions for the show statistics flow monitor Command Field Description Host Connection Configured host address IP address of the tcpstat-v1 console for the connection. Connection State State of the connection. Connection Attempts Number of connection attempts. Connection Failures Number of connection failures.
Chapter 3 CLI Commands show statistics flow Table 3-102 Field Descriptions for the show statistics flow monitor Command (continued) Field Description Dropped due to backlog Number of packets that were dropped because the queue limit has been reached. This counter indicates whether the flow monitor application can keep up with the number of summaries being received. Related Commands Summary backlog Number of packets that are waiting in the queue to be read by the collector module on the WAE.
Chapter 3 CLI Commands show statistics generic-gre show statistics generic-gre To view the GRE tunnel statistics for each intercepting router, use the show statistics generic-gre EXEC command. show statistics generic-gre Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Usage Guidelines Use the clear statistics generic-gre EXEC command to clear the generic GRE statistics.
Chapter 3 CLI Commands show statistics icmp show statistics icmp To display ICMP statistics for a WAAS device, use the show statistics icmp EXEC command. show statistics icmp Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples Table 3-104 describes the fields shown in the show statistics icmp command display.
Chapter 3 CLI Commands show statistics icmp Table 3-104 Related Commands Field Descriptions for the show statistics icmp Command (continued) Field Description ICMP messages sent Total total number of ICMP messages which this entity attempted to send. This counter includes all those counted as ICMP output errors. ICMP messages send failed Number of number of ICMP messages which this entity did not send because of problems discovered within ICMP, such as a lack of buffers.
Chapter 3 CLI Commands show statistics ip show statistics ip To display IP statistics for a WAAS device, use the show statistics ip EXEC command. show statistics ip Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples Table 3-105 describes the fields shown in the show statistics ip command display.
Chapter 3 CLI Commands show statistics ip Table 3-105 Field Descriptions for the show statistics ip Command (continued) Field Related Commands Description unknown protocol Number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol. discarded Number of input IP datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (such as, for lack of buffer space).
Chapter 3 CLI Commands show statistics ip (config-if) ip show ip routes Cisco Wide Area Application Services Command Reference OL-21611-01 3-339
Chapter 3 CLI Commands show statistics netstat show statistics netstat To display Internet socket connection statistics for a WAAS device, use the show statistics netstat EXEC command. show statistics netstat Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples Table 3-106 describes the fields shown in the show statistics netstat command display.
Chapter 3 CLI Commands show statistics pass-through show statistics pass-through To display pass-through traffic statistics for a WAAS device, use the show statistics pass-through EXEC command. show statistics pass-through Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Examples Table 3-107 describes the fields shown in the show statistics pass-through command display.
Chapter 3 CLI Commands show statistics pass-through Table 3-107 Field Descriptions for the show statistics pass-through Command (continued) Field Description In Progress Number of connections passed through due to connections seen by the WAE mid-stream. Intermediate Number of connections passed through because the WAE was in between two other WAEs. Internal Error Number of connections passed through due to miscellaneous internal errors such as memory allocation failures, and so on.
Chapter 3 CLI Commands show statistics peer show statistics peer To display peer Data Redundancy Elimination (DRE) statistics for a WAE, use the show statistics peer EXEC command.
Chapter 3 CLI Commands show statistics peer Table 3-108 Field Descriptions for the show statistics peer dre Command (continued) Field Active: Description Number of connections that are still open. Concurrent connections (Last 2 min): max Maximum number of concurrent connections in the last two minutes. avg Average number of concurrent connections in the last two minutes. Encode Overall: [msg | in | out | ratio] Statistics for compressed messages. Aggregated statistics for compressed messages.
Chapter 3 CLI Commands show statistics peer Related Commands show statistics connection closed Cisco Wide Area Application Services Command Reference OL-21611-01 3-345
Chapter 3 CLI Commands show statistics radius show statistics radius To display RADIUS authentication statistics for a WAAS device, use the show statistics radius EXEC command. show statistics radius Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples Table 3-109 describes the fields shown in the show statistics radius command display.
Chapter 3 CLI Commands show statistics radius Table 3-109 Field Descriptions for the show statistics radius Command (continued) Field Related Commands Description Number of accounting failure responses Number of accounting failure responses. Number of accounting success responses Number of accounting success responses.
Chapter 3 CLI Commands show statistics services show statistics services To display services statistics for a WAAS device, use the show statistics services EXEC command. show statistics services Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples Table 3-110 describes the fields shown in the show statistics services command display.
Chapter 3 CLI Commands show statistics snmp show statistics snmp To display SNMP statistics for a WAAS device, use the show statistics snmp EXEC command. show statistics snmp Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples Table 3-111 describes the fields shown in the show statistics snmp command display.
Chapter 3 CLI Commands show statistics snmp Table 3-111 Field Descriptions for the show statistics snmp Command (continued) Field Related Commands Description Bad values errors Number of SNMP SET requests that specified an invalid value for a MIB object. General errors Number of SNMP SET requests that failed because of some other error. (It was not a No such name error, Bad values error, or any of the other specific errors.) Response PDUs Number of responses sent in reply to requests.
Chapter 3 CLI Commands show statistics synq show statistics synq To display the cumulative statistics for the SynQ module, use the show statistics synq EXEC command. show statistics synq Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Usage Guidelines Use the show statistics synq command to display statistics for the SynQ module.
Chapter 3 CLI Commands show statistics tacacs show statistics tacacs To display TACACS+ authentication and authorization statistics for a WAAS device, use the show statistics tacacs EXEC command. show statistics tacacs Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples Table 3-112 describes the fields shown in the show statistics tacacs command display.
Chapter 3 CLI Commands show statistics tacacs Table 3-112 Field Descriptions for the show statistics tacacs Command (continued) Field Related Commands Description Number of accounting failure responses Number of accounting failure responses. Number of accounting success responses Number of accounting success responses.
Chapter 3 CLI Commands show statistics tcp show statistics tcp To display TCP statistics for a WAAS device, use the show statistics tcp EXEC command. show statistics tcp Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples Table 3-113 describes the fields shown in the show statistics tcp command display.
Chapter 3 CLI Commands show statistics tcp Table 3-113 Field Descriptions for the show statistics tcp Command (continued) Field Description Segments sent Total number of segments sent, including those on current connections but excluding those containing only retransmitted octets. Bad segments received Number of bad segments received. Segments retransmitted Total number of segments retransmitted, that is, the number of TCP segments transmitted containing one or more previously transmitted octets.
Chapter 3 CLI Commands show statistics tcp Table 3-113 Field Descriptions for the show statistics tcp Command (continued) Field Description Delayed acks blocked by socket lock Number of delayed ACKs postponed because the socket is busy. Delayed acks lost Number of delayed ACKs lost. Listen queue overflows Number of incoming TCP connections dropped because of a listening server queue overflow.
Chapter 3 CLI Commands show statistics tcp Table 3-113 Related Commands Field Descriptions for the show statistics tcp Command (continued) Field Description TCP Reno recovery fail Number of TCP Reno recovery fail. TCP Sack recovery fail Number of TCP Sack recovery failures. TCP scheduler failed Number of TCP scheduler failures. TCP receiver collapsed Number of TCP receiver collapsed failures. TCP DSACK old packets sent Number of TCP DSACK old packets sent.
Chapter 3 CLI Commands show statistics tfo show statistics tfo To display Traffic Flow Optimization (TFO) statistics for a WAE, use the show statistics tfo EXEC command. show statistics tfo [connection | detail] show statistics tfo peer [peer-id peer-id | peer-ip peer-ip | peer-no peer-no] Syntax Description connection (Optional) Displays aggregated TFO connection statistics. detail (Optional) Displays detailed TFO statistics. peer (Optional) Displays DRE peer statistics.
Chapter 3 CLI Commands show statistics tfo Table 3-114 Field Descriptions for the show statistics tfo Command (continued) Field Description WAN socket error close while waiting to read The socket between two WAEs (WAN socket) closed before completing reading from it. AO socket error close while waiting to read The socket between the WAE and the client/server (LAN socket) closed before completing reading from it. DRE decode failure DRE internal error while decoding data. (Should not happen.
Chapter 3 CLI Commands show statistics tfo Table 3-114 Field Descriptions for the show statistics tfo Command (continued) Field Description Total timeouts The total number of times the TFO component did not issue a keepalive to the Policy Engine in a timely manner. This may encompass multiple registrations. Last keepalive received The amount of time since the last keepalive (seconds).
Chapter 3 CLI Commands show statistics tfo Table 3-114 Field Descriptions for the show statistics tfo Command (continued) Field Description Auto-Discovery Statistics Related Commands Total connections queued for accept Total number of connections added to the TFO connection accept queue by auto discovery. Accept queue add failures Number of connections that could not be added to the TFO connection accept queue due to a failure. The failure could possibly be due to queue overflow.
Chapter 3 CLI Commands show statistics udp show statistics udp To display User Datagram Protocol (UDP) statistics for a WAAS device, use the show statistics udp EXEC command. show statistics udp Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples Table 3-115 describes the fields shown in the show statistics udp command display.
Chapter 3 CLI Commands show statistics wccp show statistics wccp To display WCCP statistics for a WAE, use the show statistics wccp EXEC command. show statistics wccp gre Syntax Description gre Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Usage Guidelines GRE is a Layer 3 technique that allows datagrams to be encapsulated into IP packets at the WCCP-enabled router and then redirected to a WAE (the transparent proxy server).
Chapter 3 CLI Commands show statistics wccp Table 3-116 Field Descriptions for the show statistics wccp gre Command Field Description Transparent GRE packets received Total number of GRE packets received by the WAE, regardless of whether or not they have been intercepted by WCCP. GRE is a Layer 3 technique that allows packets to reach the WAE, even if there are any number of routers in the path to the WAE.
Chapter 3 CLI Commands show statistics wccp Table 3-116 Field Descriptions for the show statistics wccp gre Command (continued) Field Description Connections bypassed due to load Number of connection flows that are bypassed when the WAE is overloaded. When the overload bypass option is enabled, the WAE bypasses a bucket and reroutes the overload traffic. If the load remains too high, another bucket is bypassed, and so on, until the WAE can handle the load.
Chapter 3 CLI Commands show statistics wccp Table 3-116 Related Commands Field Descriptions for the show statistics wccp gre Command (continued) Field Description Packets bypassed due to bypass-list lookup Number of connection flows that are bypassed due to a bypass list entry. When the WAE receives an error response from an origin server, it adds an entry for the server to its bypass list.
Chapter 3 CLI Commands show statistics windows-domain show statistics windows-domain To display Windows domain server information for a WAAS device, use the show statistics windows-domain EXEC command. show statistics windows-domain Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands show statistics windows-domain Table 3-117 Field Descriptions for the show statistics windows-domain Command (continued) Field Description Accounting Related Commands Number of accounting requests Number of accounting requests. Number of accounting failure responses Number of accounting failure responses. Number of accounting success responses Number of accounting success responses.
Chapter 3 CLI Commands show statistics windows-print requests show statistics windows-print requests To display Windows print acceleration statistics for a WAE, use the show statistics windows-print requests EXEC command. show statistics windows-print requests Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands show statistics windows-print requests Related Commands (config) accelerator windows-print Cisco Wide Area Application Services Command Reference 3-370 OL-21611-01
Chapter 3 CLI Commands show synq list show synq list To display the connections for the SynQ module, use the show synq list EXEC command. show synq list [| {begin regex [regex] | exclude regex [regex] | include regex [regex]}] [| {begin regex [regex] | exclude regex [regex] | include regex [regex]}] Syntax Description | (Optional) Output modifier. begin regex Begins with the line that matches the regular expression. You can enter multiple expressions.
Chapter 3 CLI Commands show sysfs volumes show sysfs volumes To display system file system (sysfs) information for a WAAS device, use the show sysfs volumes EXEC command. show sysfs volumes Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines The system file system (sysfs) stores log files, including transaction logs, syslogs, and internal debugging logs.
Chapter 3 CLI Commands show tacacs show tacacs To display TACACS+ authentication protocol configuration information for a WAAS device, use the show tacacs EXEC command. show tacacs Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples Table 3-120 describes the fields shown in the show tacacs command display.
Chapter 3 CLI Commands show tacacs Table 3-120 Related Commands Field Descriptions for the show tacacs Command (continued) Field Description Server Hostname or IP address of the TACACS+ server. Status Indicates whether server is the primary or secondary host.
Chapter 3 CLI Commands show tcp show tcp To display TCP configuration information for a WAAS device, use the show tcp EXEC command. show tcp Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples Table 3-121 describes the fields shown in the show tcp command display. This command displays the settings configured with the tcp global configuration command.
Chapter 3 CLI Commands show tcp Related Commands clear arp-cache show statistics tcp (config) tcp Cisco Wide Area Application Services Command Reference 3-376 OL-21611-01
Chapter 3 CLI Commands show tech-support show tech-support To view information necessary for Cisco TAC to assist you, use the show tech-support EXEC command. show tech-support [page] Syntax Description page Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator (Optional) Displays command output page by page.
Chapter 3 CLI Commands show tech-support List of all disk drives: Physical disk information: disk00: Normal disk01: Normal (IDE disk) (IDE disk) 76324MB( 74.5GB) 76324MB( 74.5GB) Mounted filesystems: MOUNT POINT / /sw /swstore /state /disk00-04 /local/local1 ...
Chapter 3 CLI Commands show tech-support show processes memory show memory show interface show cdp entry show cdp neighbors show statistics wccp show alarms all show statistics auto-discovery show statistics filtering show statistics ip show statistics icmp show statistics netstat show statistics peer show statistics tfo show policy-engine status show policy-engine application show disks SMART-info show disks SMART-info details show disks failed-sectors Cisco Wide Area Application Services Command Refere
Chapter 3 CLI Commands show telnet show telnet To display Telnet services configuration for a WAAS device, use the show telnet EXEC command. show telnet Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples The following is sample output from the show telnet command. It shows whether or not Telnet is enabled on the WAAS device.
Chapter 3 CLI Commands show tfo tcp show tfo tcp To display global Traffic Flow Optimization (TFO) TCP buffer information for a WAE, use the show tfo tcp EXEC command. show tfo tcp Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Examples The following is sample output from the show tfo tcp command. It displays TCP buffer information for the WAE.
Chapter 3 CLI Commands show transaction-logging show transaction-logging To display the transaction log configuration settings and a list of archived transaction log files for a WAE, use the show transaction-logging EXEC command. show transaction-logging Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands show transaction-logging Related Commands clear arp-cache transaction-log (config) transaction-logs Cisco Wide Area Application Services Command Reference OL-21611-01 3-383
Chapter 3 CLI Commands show user show user To display user identification number and username information for a particular user of a WAAS device, use the show user EXEC command. show user {uid number | username name} Syntax Description uid number Displays user information based on the identification number of the user (0–65535). username name Displays user information based on the name of the user. Command Default No default behavior or values.
Chapter 3 CLI Commands show users administrative show users administrative To display users with administrative privileges to the WAAS device, use the show users administrative EXEC command. show users administrative [history | locked-out | logged-in] Syntax Description administrative Displays a list of users defined on the device. history Displays a historical list of user log-ins. locked-out Displays a list of locked out users. logged-in Displays a list of users that are logged in.
Chapter 3 CLI Commands show users administrative Table 3-124 Related Commands Field Descriptions for the show users administrative logged-in Command Field Description IP address/Host IP address or hostname of the user that is logged in to this appliance. Loginn details Day of week, month, date, and time that each user logged in.
Chapter 3 CLI Commands show version show version To display version information about the WAAS software that is running on the WAAS device, use the show version EXEC command. show version [last | pending] Syntax Description last (Optional) Displays the version information for the last saved image. pending (Optional) Displays the version information for the pending upgraded image. Defaults No default behavior or values.
Chapter 3 CLI Commands show virtual-blade show virtual-blade To display virtual blade information on your WAE device, use the show virtual-blade EXEC command. show virtual-blade [virtual-blade-number [blockio | interface {1 | 2}] | detail | vmstat] Syntax Description virtual-blade-number Specifies an individual virtual blade for which to view detailed information. blockio Displays statistics information for disk devices on a virtual blade.
Chapter 3 CLI Commands show virtual-blade interface 1 bridge GigabitEthernet 1/0 mac-address 00:16:3E:97:6F:84 no vnc autostart state: running serial console session inactive vnc server disabled current cd /local1/vbs/WoW_1.0.2.iso current floppy [not inserted] Table 3-126 describes the fields shown in the general show virtual-blade display.
Chapter 3 CLI Commands show virtual-blade Table 3-127 Related Commands Field Descriptions for the show virtual-blade detail Command Field Description autostart Shows that the virtual blade is configured to start automatically. state State of the virtual blade (running or stopped) and other runtime information.
Chapter 3 CLI Commands show wccp show wccp To display Web Cache Connection Protocol (WCCP) information for a WAE, use the show wccp EXEC command. show wccp wide-area-engines show wccp flows {tcp-promiscuous} [summary] show wccp gre show wccp masks {tcp-promiscuous} [summary] show wccp routers show wccp services [detail] show wccp status Syntax Description wide-area-engines Displays which WAEs are seen by which routers. flows Displays WCCP packet flows.
Chapter 3 CLI Commands show wccp Table 3-128 Field Descriptions for the show wccp gre Command Field Description Transparent GRE packets received Total number of GRE packets received by the WAE, regardless of whether or not they have been intercepted by WCCP. GRE is a Layer 3 technique that allows packets to reach the WAE, even if there are any number of routers in the path to the WAE.
Chapter 3 CLI Commands show wccp Table 3-128 Field Descriptions for the show wccp gre Command (continued) Field Description Connections bypassed due to load Number of connection flows that are bypassed when the WAE is overloaded. When the overload bypass option is enabled, the WAE bypasses a bucket and reroutes the overload traffic. If the load remains too high, another bucket is bypassed, and so on, until the WAE can handle the load.
Chapter 3 CLI Commands show wccp Table 3-128 Field Descriptions for the show wccp gre Command (continued) Field Description Packets bypassed due to bypass-list lookup Number of connection flows that are bypassed due to a bypass list entry. When the WAE receives an error response from an origin server, it adds an entry for the server to its bypass list. When it receives subsequent requests for the content residing on the bypassed server, it redirects packets to the bypass gateway.
Chapter 3 CLI Commands show wccp Security Enabled for Service Multicast Enabled for Service Weight for this Web-CE Negotiated forwarding method Negotiated assignment method Negotiated return method Received Values: Source IP mask (in Hex) Destination IP mask (in Hex) Source Port mask (in Hex) Destination Port mask (in Hex) Calculated Values: Source IP mask (in Hex) Destination IP mask (in Hex) Source Port mask (in Hex) Destination Port mask (in Hex) : : : : : : No No 0 GRE HASH GRE : : : : 0 0 0 0 :
Chapter 3 CLI Commands show wccp -NONE- The following is sample output from the show wccp status command: WAE# show wccp status WCCP version 2 is enabled and currently active Related Commands (config) wccp access-list (config) wccp flow-redirect (config) wccp router-list (config) wccp shutdown (config) wccp tcp-promiscuous mask (config) wccp version Cisco Wide Area Application Services Command Reference 3-396 OL-21611-01
Chapter 3 CLI Commands show windows-domain show windows-domain To display Windows domain configuration information for a WAAS device, use the show windows-domain EXEC command. show windows-domain Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Examples Table 3-129 describes the fields shown in the show windows-domain command display.
Chapter 3 CLI Commands show windows-domain Table 3-129 Field Descriptions for the show windows-domain Command (continued) Field Related Commands Description Super user group Active Directory(AD) group name. Users in this group have administrative rights. Normal user group AD group name. Users in this group have the normal/default privilege level in the WAE.
Chapter 3 CLI Commands shutdown shutdown To shut down the WAAS device, use the shutdown EXEC command. shutdown [poweroff] Syntax Description poweroff Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator (Optional) Turns off the power after closing all applications and operating system. central-manager Usage Guidelines A controlled shutdown refers to the process of properly shutting down a WAAS device without turning off the power on the device.
Chapter 3 CLI Commands shutdown The shutdown poweroff command closes all applications and the operating system, stops all system activities, and turn off the power. The fans stop running and the power LED starts flashing, indicating that the device has been powered off. Note If you use the shutdown or shutdown poweroff commands, the device does not perform a file system check when you power on and boot the device the next time.
Chapter 3 CLI Commands shutdown To power down the WAAS device, press and hold the power button on the WAAS device, or use one of the following methods to perform a shutdown poweroff: • From the console command line, enter 2 when prompted, as follows: ================= SHUTDOWN SHELL ================= System has been shut down. You can either Power down system by pressing and holding power button or 1. Reload system through software 2.
Chapter 3 CLI Commands snmp trigger snmp trigger To configure thresholds for a user-selected MIB object for monitoring purposes on a WAAS device, use the snmp trigger EXEC command.
Chapter 3 CLI Commands snmp trigger delta value Specifies a delta sample type. falling Applies the falling threshold test. greater-than Applies the greater-than threshold test. less-than Applies the less-than threshold test. on-change Applies the changed existence test. present Applies the present test. rising Applies the rising threshold test. delete Removes a threshold for a MIB object. Defaults No default behavior or values.
Chapter 3 CLI Commands snmp trigger After you configure SNMP traps, you must use the snmp-server enable traps event global configuration command for the event traps you just created to be generated. Also, to preserve SNMP trap configuration across a system reboot, you must configure event persistence using the snmp-server mib persist event global configuration command, and save the MIB data using the write mib-data EXEC command.
Chapter 3 CLI Commands snmp trigger (config) snmp-server user (config) snmp-server view write Cisco Wide Area Application Services Command Reference OL-21611-01 3-405
Chapter 3 CLI Commands ssh ssh To allow secure encrypted communications between an untrusted client machine and a WAAS device over an insecure network, use the ssh EXEC command. ssh options Syntax Description options Defaults By default, the Secure Shell (SSH) feature is disabled on a WAAS device. Command Modes EXEC Device Modes application-accelerator Options to use with the ssh EXEC command. For more information about the possible options, see RFC 4254 at http://www.rfc-archive.org/getrfc.
Chapter 3 CLI Commands tcpdump tcpdump To dump network traffic, use the tcpdump EXEC command. tcpdump [LINE] Syntax Description LINE Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator (Optional) Dump options. For more information see the “Usage Guidelines” section.
Chapter 3 CLI Commands tcpdump traceroute Cisco Wide Area Application Services Command Reference 3-408 OL-21611-01
Chapter 3 CLI Commands telnet telnet To log in to a WAAS device using the Telnet client, use the telnet EXEC command. telnet {hostname | ip-address} [portnum] Syntax Description hostname Hostname of the network device. ip-address IP address of the network device. portnum (Optional) Port number (1–65535). Default port number is 23. Defaults The default port number is 23.
Chapter 3 CLI Commands terminal terminal To set the number of lines displayed in the console window, or to display the current console debug command output, use the terminal EXEC command. terminal {length length | monitor [disable]} Syntax Description length length Sets the length of the display on the terminal (0–512). Setting the length to 0 means there is no pausing. monitor Copies the debug output to the current terminal. disable (Optional) Disables monitoring at this specified terminal.
Chapter 3 CLI Commands test test To perform diagnostic tests and display the results, use the test EXEC command. test self-diagnostic [system | basic | connectivity | interfaces | application-security | tfo | wccp | inline | wafs ] | all Syntax Description self-diagnostic Performs self-diagnostics tests. system (Optional) Checks the device status, presence of core files, and alarms. basic (Optional) Checks the device network configuration.
Chapter 3 CLI Commands test Table 3-131 describes the error messages that can be returned by the test self-diagnostics command. Table 3-131 Error Codes Returned by the test self-diagnostics Command Test Error Code Description system HAS_COREDUMP Core files are present. HAS_ALARM Critical or major alarms are pending. NO_PRIM_IFACE The primary interface is not configured. NO_PRIM_ADDR The primary interface has no IP address configured. NO_HOSTNAME The hostname is not configured.
Chapter 3 CLI Commands test Table 3-131 Error Codes Returned by the test self-diagnostics Command (continued) Test Error Code Description inline INLINE_NO_INT Traffic interception is not configured on the inlineGroup interface. INLINE_SHUTDOWN The inlineGroup interface is shut down. INLINE_BYPASS The inlineGroup interface is in bypass mode. INLINE_INTRCPT The inlineGroup interface is not intercepting traffic.
Chapter 3 CLI Commands tethereal tethereal To analyze network traffic from the command line, use the tethereal EXEC command. tethereal [LINE] Syntax Description LINE Defaults No default behavior values. Command Modes EXEC Device Modes application-accelerator (Optional) Options. For more information see the “Usage Guidelines” and “Examples” sections. central-manager Usage Guidelines Tethereal is the command-line version of the network traffic analyzer tool Ethereal.
Chapter 3 CLI Commands tethereal Usage: tshark [options] ... Capture interface: -i -f -s -p -y -D -L Capture stop conditions: -c -a ...
Chapter 3 CLI Commands top top To view the current top CPU activities, use the top EXEC command. top -hv | -cisS -d delay -n iterations [-u user | -U user] -p pid [,pid ...] Syntax Description -h (Optional) Print help information and exit. -v (Optional) Print version information and exit. -c (Optional) Display the command line instead of the command name only. -i (Optional) Suppress display of any idle or zombie processes. -s (Optional) Tells top to run in secure mode.
Chapter 3 CLI Commands top 1,I Toggle SMP view: '1' single/separate states; 'I' Irix/Solaris mode f,o F or O <,> R c,i,S x,y z,b u n or # . . . . . . . . .
Chapter 3 CLI Commands traceroute traceroute To trace the route between a WAAS device to a remote host, use the traceroute EXEC command. traceroute {hostname | ip-address} Syntax Description hostname Name of remote host. ip-address IP address of remote host. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines Traceroute is a widely available utility on most operating systems.
Chapter 3 CLI Commands transaction-log transaction-log To force the exporting or the archiving of the transaction log, use the transaction-log EXEC command. transaction-log force {archive | export} {flow | accelerator video windows-media} Syntax Description archive Forces the archiving of the transaction log file. export Forces the archived transaction log files to be exported. flow Forces the archiving or exporting of the Traffic Flow Optimization (TFO) transaction log file.
Chapter 3 CLI Commands type type To display a file, use the type EXEC command. type filename Syntax Description filename Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator Name of file. central-manager Usage Guidelines Use the type command to display the contents of a file within any file directory on a WAAS device. The type command may be used to monitor features such as transaction logging or system logging (syslog).
Chapter 3 CLI Commands type-tail type-tail To view a specified number of lines of the end of a log file, to view the end of the file continuously as new lines are added to the file, to start at a particular line in the file, or to include or exclude specific lines in the file, use the type-tail EXEC command. type-tail filename [line | follow | | {begin LINE | exclude LINE | include LINE}] Syntax Description filename File to be examined.
Chapter 3 CLI Commands type-tail dbupgrade.log downgrade errorlog logs lost+found sa service_logs spool syslog.txt syslog.txt.1 syslog.txt.2 syslog.txt.3 syslog.txt.4 var wdd.sh.signed WAE# type-tail /local1/syslog.
Chapter 3 CLI Commands virtual-blade virtual-blade To change the virtual blade CD-ROM, save or delete the memory state, reset, or start and stop a virtual blade, use the virtual-blade EXEC command. virtual-blade [bladenumber] {cd {cd-rom | disk pathname | eject} | kill-save-state | reset | save | session [clear] | start [delay] | stop [timeout]} Syntax Description bladenumber Number of the virtual blade. Valid values depend on the hardware capabilities.
Chapter 3 CLI Commands virtual-blade The virtual-blade n reset command immediately resets the virtual blade operating system, similar to pressing the reset button on a real computer. Because this is not a clean shutdown, you are prompted to confirm this command. The virtual-blade n start and virtual-blade n stop commands allow you to activate and deactive the virtual blade. Each command has an optional delay.
Chapter 3 CLI Commands wafs wafs To back up, restore, or create a system report about the legacy Wide Area File Services (WAFS)-related network configuration, plus the configurations of file servers, printers, users, and so forth, on a WAE, use the wafs EXEC command. wafs {backup-config filename | restore-config filename | sysreport [filename | date-range from_date end_date filename]} Note Syntax Description Executing the wafs sysreport command can temporarily impact the performance of your WAE.
Chapter 3 CLI Commands wafs Examples The following example shows how to create a backup file of the WAFS configuration information: WAE# wafs ? backup-config restore-config sysreport backup system configurations to a file. restore system configurations from a file. WARNING: After restoring configuration, the system needs to be restarted and re-registered. system report to a file WAE# wafs backup-config backup.tar.gz system configuration is stored in file /local/local1/backup.tar.
Chapter 3 CLI Commands whoami whoami To display the username of the current user, use the whoami EXEC command. whoami Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Device Modes application-accelerator central-manager Usage Guidelines Use the whoami command to display the username of the current user.
Chapter 3 CLI Commands windows-domain windows-domain To access the Windows domain utilities on a WAAS device, use the windows-domain EXEC command. windows-domain diagnostics {findsmb | getent | net | nmblookup | smbclient | smbstatus | smbtree | tdbbackup | tdbdump | testparm | wbinfo} Syntax Description diagnostics Enables selection of Windows domain diagnostic utilities. findsmb Displays the utility for troubleshooting NetBIOS name resolution and browsing.
Chapter 3 CLI Commands windows-domain -s, --service=CONFIG -?, --help --usage -V, --version Service configuration to be used Give this help list Give a short usage message Print program version Mandatory or optional arguments to long options are also mandatory or optional for any corresponding short options.
Chapter 3 CLI Commands windows-domain The following example shows how to register a Windows domain: WAE# windows-domain diagnostics net join -S -U% Related Commands (config) windows-domain Cisco Wide Area Application Services Command Reference 3-430 OL-21611-01
Chapter 3 CLI Commands write write To save startup configurations on a WAAS device, use the write EXEC command. write [erase | memory | mib-data | terminal] Syntax Description erase (Optional) Erases startup configuration from NVRAM. memory (Optional) Writes the configuration to NVRAM. This is the default location for saving startup information. mib-data (Optional) Saves MIB persistent configuration data to disk. terminal (Optional) Writes the configuration to a terminal session.
Chapter 3 CLI Commands Global Configuration Mode Commands Use global configuration mode for setting, viewing, and testing configuration of WAAS software features for the entire device. To enter this mode, enter the configure command from privileged EXEC mode. The prompt for global configuration mode consists of the hostname of the WAE followed by (config) and the pound sign (#). You must be in global configuration mode to enter global configuration commands.
Chapter 3 CLI Commands (config) aaa accounting (config) aaa accounting To configure AAA accounting on a WAAS device, use the aaa accounting global configuration command. To unconfigure AAA, use the no form of this command.
Chapter 3 CLI Commands (config) aaa accounting Device Modes application-accelerator central-manager Examples The following example shows how to configure TACACS+ on the WAAS device, specify that a start accounting notice should be sent at the beginning of the process and a stop accounting notice at the end of the process, and request that the user process should begin regardless of whether the start accounting notice was received by the accounting server: WAE(config)# tacacs key abc WAE(config)# tacac
Chapter 3 CLI Commands (config) aaa accounting task_id=5358 timezone=PST service=system event=sys_acct reason=shutdown The following example shows the command accounting report that is available on the TACACS+ server: Wed Apr 14 12:35:38 2004 172.16.0.0 admin ttyS0 0.0.0.0 start start_time=1081924137 task_id=3511 timezone=PST service=shell -lvl=0 cmd=logging console enable Wed Apr 14 12:35:39 2004 172.16.0.0 admin ttyS0 0.0.0.
Chapter 3 CLI Commands (config) aaa authorization commands (config) aaa authorization commands To authorize commands issued through the CLI by a user on a WAAS device, use the aaa authorization commands global configuration command. To disable command authorization, use the no form of this command. aaa authorization commands level default tacacs+ no aaa authorization commands level default tacacs+ Syntax Description level default tacacs+ Defaults AAA command authorization is disabled by default.
Chapter 3 CLI Commands (config) accelerator cifs (config) accelerator cifs To enable the CIFS application accelerator, use the accelerator cifs global configuration command. To disable the CIFS application accelerator, use the no form of this command.
Chapter 3 CLI Commands (config) accelerator cifs Note We recommend that you use the WAAS Central Manager GUI to configure dynamic shares because the dynamic share CLI configuration can be overwritten by the Central Manager. For more information, see the “Creating Dynamic Shares” section in the Cisco Wide Area Application Services Configuration Guide.
Chapter 3 CLI Commands (config) accelerator cifs preposition (config) accelerator cifs preposition To configure a CIFS application accelerator preposition directive, use the accelerator cifs preposition global configuration command. To disable the application accelerator, use the no form of this command. accelerator cifs preposition [remove] directive_id no accelerator cifs preposition [remove] directive_id Syntax Description remove (Optional) Deletes a preposition directive.
Chapter 3 CLI Commands (config) accelerator cifs preposition Related Commands show accelerator show statistics accelerator (config) windows-domain Cisco Wide Area Application Services Command Reference 3-440 OL-21611-01
Chapter 3 CLI Commands (config) accelerator epm (config) accelerator epm To enable the Endpoint Mapper (EPM) application accelerator, use the accelerator epm global configuration command. To disable the EPM application accelerator, use the no form of this command. accelerator cifs preposition [remove] directive_id no accelerator cifs preposition [remove] directive_id Syntax Description enable (Optional) Enables the EPM application accelerator.
Chapter 3 CLI Commands (config) accelerator http (config) accelerator http To enable the HTTP application accelerator, use the accelerator http global configuration command. To disable the HTTP application accelerator, use the no form of this command.
Chapter 3 CLI Commands (config) accelerator http Command Modes global configuration Device Modes application-accelerator Usage Guidelines Use the accelerator http enable command to enable the acceleration of HTTP traffic. You can enable or disable each of three metadata caches (conditional-response, redirect-response, and unauthorized-response) separately. By default they are all enabled when you enable HTTP metadata caching. If you disable the HTTP accelerator, metadata caching is also disabled.
Chapter 3 CLI Commands (config) accelerator mapi (config) accelerator mapi To enable the MAPI application accelerator, use the accelerator mapi global configuration command. To disable the MAPI application accelerator, or one of its options, use the no form of this command.
Chapter 3 CLI Commands (config) accelerator mapi The client maintains at least one AG per server it connects to with an average of about 3 connections per AG. For deployments that observe a greater average number of connections per AG, or where TFO overload is a frequent occurrence, a higher value for the reserved pool size maximum percent is recommended. Reserved connections would remain unused when the device is not under TFO overload. Reserved connections are released when the AG terminates.
Chapter 3 CLI Commands (config) accelerator nfs (config) accelerator nfs To enable the NFS application accelerator, use the accelerator nfs global configuration command. To disable the NFS application accelerator, use the no form of this command. accelerator nfs {enable | exception {coredump | debug | no-coredump}} no accelerator nfs {enable | exception {coredump | debug | no-coredump}} Syntax Description enable (Optional) Enables the EPM application accelerator.
Chapter 3 CLI Commands (config) accelerator ssl (config) accelerator ssl To enable the SSL application accelerator, use the accelerator ssl global configuration command. To disable the SSL application accelerator, use the no form of this command. accelerator ssl {enable | exception {coredump | debug | no-coredump}} no accelerator ssl {enable | exception {coredump | debug | no-coredump}} Syntax Description enable (Optional) Enables the EPM application accelerator.
Chapter 3 CLI Commands (config) accelerator ssl (config-ca) ca-certificate (config-ca) description (config-ca) revocation-check Cisco Wide Area Application Services Command Reference 3-448 OL-21611-01
Chapter 3 CLI Commands (config) accelerator video (config) accelerator video To enable the video application accelerator, use the accelerator video global configuration command. To disable the video application accelerator, use the no form of this command.
Chapter 3 CLI Commands (config) accelerator video Command Modes global configuration Device Modes application-accelerator Usage Guidelines Use the accelerator video enable command to enable the acceleration of Windows Media live streaming video traffic that uses the RTSP. You can configure the video accelerator to discard unaccelerated video traffic by using the unaccelerated-traffic type {all | overload} action drop option.
Chapter 3 CLI Commands (config) accelerator windows-print (config) accelerator windows-print To enable the Windows print accelerator, use the accelerator windows-print global configuration command. To disable the Windows print accelerator, use the no form of this command. accelerator windows-print enable no accelerator windows-print enable Syntax Description This command has no arguments or keywords.
Chapter 3 CLI Commands (config) alarm overload-detect (config) alarm overload-detect To detect alarm overload situations, use the alarm overload-detect global configuration command. To unconfigure alarm parameters, use the no form of this command.
Chapter 3 CLI Commands (config) alarm overload-detect WAE(config)# alarm overload-detect clear 10 Related Commands show alarms Cisco Wide Area Application Services Command Reference OL-21611-01 3-453
Chapter 3 CLI Commands (config) asset (config) asset To set the tag name for the asset tag string, use the asset global configuration command. To remove the asset tag name, use the no form of this command. asset tag name no asset tag name Syntax Description tag name Defaults No default behaviors or values. Command Modes global configuration Device Modes application-accelerator Sets the asset tag name.
Chapter 3 CLI Commands (config) authentication configuration (config) authentication configuration To specify administrative login authorization parameters for a WAAS device, use the authentication configuration global configuration mode command. To selectively disable options, use the no form of this command.
Chapter 3 CLI Commands (config) authentication configuration The authentication login command determines whether the user has any level of permission to access the WAAS device. The authentication configuration command authorizes the user with privileged access (configuration access) to the WAAS device. The authentication login local and the authentication configuration local commands use a local database for authentication and authorization.
Chapter 3 CLI Commands (config) authentication configuration Specifying RADIUS Authentication and Authorization Settings To configure RADIUS authentication on a WAAS device, you must first configure a set of RADIUS authentication server settings on the WAAS device by using the radius-server global configuration command. (See the (config) radius-server command.) Use the authentication login radius global configuration command to enable RADIUS authentication for normal login mode.
Chapter 3 CLI Commands (config) authentication configuration To enable authentication privileges using the local, TACACS+, RADIUS, or Windows databases, and to specify the order of the administrative login authentication, use the authentication login global configuration command. In the following example, RADIUS is specified as the primary method, TACACS+ as the secondary method, Windows as the third method, and the local database as the fourth method.
Chapter 3 CLI Commands (config) authentication configuration Configuration Authentication: ----------------------------local Radius Tacacs+ Related Commands Console/Telnet/Ftp/SSH Session -----------------------------enabled (primary) disabled disabled (config) radius-server show authentication show statistics radius show statistics tacacs (config) tacacs windows-domain (config) windows-domain Cisco Wide Area Application Services Command Reference OL-21611-01 3-459
Chapter 3 CLI Commands (config) authentication content-request (config) authentication content-request To authenticate a request for content, use the authentication content-request global configuration mode command. To selectively disable options, use the no form of this command.
Chapter 3 CLI Commands (config) authentication content-request The authentication login radius and authentication configuration radius commands use a remote RADIUS server to determine the level of user access. By default, the local method is enabled, with TACACS+ and RADIUS both disabled for login and configuration. Whenever TACACS+ and RADIUS are disabled the local method is automatically enabled. TACACS+, RADIUS, and local methods can be enabled at the same time.
Chapter 3 CLI Commands (config) authentication content-request Specifying TACACS+ Authentication and Authorization Settings To configure TACACS+ authentication on WAAS devices, you must configure a set of TACACS+ authentication settings on the WAAS device by using the tacacs global configuration command. (See the (config) tacacs command.) Server Redundancy Authentication servers can be specified with the tacacs host or radius-server host global configuration commands.
Chapter 3 CLI Commands (config) authentication content-request To enable authorization privileges using the local, TACACS+, RADIUS, or Windows databases, and to specify the order of the administrative login authorization (configuration), use the authentication configuration global configuration command. Note Authorization privileges apply to console and Telnet connection attempts, secure FTP (SFTP) sessions, and Secure Shell (SSH, Version 1 and Version 2) sessions.
Chapter 3 CLI Commands (config) authentication fail-over (config) authentication fail-over To specify authentication failover if the primary authentication server is unreachable, use the authentication fail-over global configuration mode command. To disable this feature, use the no form of this command. authentication fail-over server-unreachable no authentication fail-over server-unreachable Syntax Description fail-over server-unreachable Defaults This feature is disabled by default.
Chapter 3 CLI Commands (config) authentication fail-over Examples The following example shows how to query the secondary authentication database if the primary authentication server is unreachable. This feature is referred to as the failover server-unreachable feature.
Chapter 3 CLI Commands (config) authentication login (config) authentication login To set the administrative login authentication parameters for a WAAS device, use the authentication login global configuration mode command. To selectively disable options, use the no form of this command.
Chapter 3 CLI Commands (config) authentication login The authentication login command determines whether the user has any level of permission to access the WAAS device. The authentication configuration command authorizes the user with privileged access (configuration access) to the WAAS device. The authentication login local and the authentication configuration local commands use a local database for authentication and authorization.
Chapter 3 CLI Commands (config) authentication login Specifying RADIUS Authentication and Authorization Settings To configure RADIUS authentication on a WAAS device, you must first configure a set of RADIUS authentication server settings on the WAAS device by using the radius-server global configuration command. (See the (config) radius-server command.) Use the authentication login radius global configuration command to enable RADIUS authentication for normal login mode.
Chapter 3 CLI Commands (config) authentication login To enable authentication privileges using the local, TACACS+, RADIUS, or Windows databases, and to specify the order of the administrative login authentication, use the authentication login global configuration command. In the following example, RADIUS is specified as the primary method, TACACS+ as the secondary method, Windows as the third method, and the local database as the fourth method.
Chapter 3 CLI Commands (config) authentication login Configuration Authentication: ----------------------------local Radius Tacacs+ Related Commands Console/Telnet/Ftp/SSH Session -----------------------------enabled (primary) disabled disabled (config) radius-server show authentication show statistics radius show statistics tacacs (config) tacacs windows-domain (config) windows-domain Cisco Wide Area Application Services Command Reference 3-470 OL-21611-01
Chapter 3 CLI Commands (config) authentication strict-password-policy (config) authentication strict-password-policy To activate the strong password policy on a WAAS device, use the authentication strict-password-policy global configuration command. To deactivate the strong password policy and use the standard password policy on a WAAS device, use the no form of this command.
Chapter 3 CLI Commands (config) authentication strict-password-policy Note Examples When you enable the strong password policy, existing standard-policy passwords will still work. However, these passwords are subject to expiration under the strong password policy.
Chapter 3 CLI Commands (config) auto-discovery (config) auto-discovery To configure a WAE to automatically discover origin servers (such as those servers behind firewalls) that cannot receive TCP packets with setup options and add these server IP addresses to a blacklist for a specified number of minutes, use the auto-discovery global configuration command. To disable auto-discovery, use the no form of this command.
Chapter 3 CLI Commands (config) auto-register (config) auto-register To enable the discovery of a Fast Ethernet or Gigabit Ethernet WAE and its automatic registration with the WAAS Central Manager through the Dynamic Host Configuration Protocol (DHCP), use the auto-register global configuration command. To disable the autoregistration feature on a WAE, use the no form of this command.
Chapter 3 CLI Commands (config) auto-register To assign a static IP address using the interface GigabitEthernet slot/port command, you must first disable the automatic registration of devices through DHCP by using the no auto-register enable command.
Chapter 3 CLI Commands (config) banner (config) banner To configure the EXEC, login, and message-of-the-day (MOTD) banners, use the banner global configuration command. To disable the banner feature, use the no form of this command. banner {enable | {{exec | login | motd} [message text]}} no banner {enable | {{exec | login | motd} [message text]}} Syntax Description enable Enables banner support on the WAE. exec Configures an EXEC banner.
Chapter 3 CLI Commands (config) banner The following example shows how to use the banner motd message global command to configure a MOTD message that is longer than a single line. In this case, the WAE translates the \n portion of the message to a new line when the MOTD message is displayed to the user. WAE(config)# banner motd message "This is the motd message. \nThis is a WAAS 4.0.
Chapter 3 CLI Commands (config) banner Related Commands show banner Cisco Wide Area Application Services Command Reference 3-478 OL-21611-01
Chapter 3 CLI Commands (config) bypass (config) bypass To configure static bypass lists on a WAE, use the bypass global configuration command. To disable the bypass feature (clear the static bypass lists), use the no form of this command. bypass static {clientip | any-client} {serverip | any-server} no bypass static {clientip | any-client} {serverip | any-server} Syntax Description static Adds a static entry to the bypass list. clientip Requests from this IP address bypass the WAE.
Chapter 3 CLI Commands (config) bypass WAE(config)# bypass static 10.1.17.1 any-server A static list of source and destination addresses helps to isolate instances of problem-causing clients and servers. To display static configuration list items, use the show bypass list command as follows: WAE# show bypass list Client Server ----------10.1.17.1:0 172.16.7.52:0 any-client:0 172.16.7.52:0 10.1.17.
Chapter 3 CLI Commands (config) cdp (config) cdp To configure the Cisco Discovery Protocol (CDP) options globally on all WAAS device interfaces, use the cdp global configuration command. To disable CDP, use the no form of this command. cdp {enable | holdtime seconds | timer seconds} no cdp {enable | holdtime seconds | timer seconds} Syntax Description Defaults enable Enables CDP globally.
Chapter 3 CLI Commands (config) central-manager (config) central-manager To specify the WAAS Central Manager role and port number, use the central-manager global configuration command in central-manager device mode. To specify the IP address or hostname of the WAAS Central Manager with which a WAE is to register, use the central-manager global configuration command in application-accelerator device mode. To negate these actions, use the no form of this command.
Chapter 3 CLI Commands (config) central-manager waas-cm(config)# central-manager role primary The following example shows how to specify that the WAE should register with the WAAS Central Manager that has an IP address of 10.1.1.1. This command associates the WAE with the primary WAAS Central Manager so that the WAE can be approved as a part of the WAAS network. WAE(config)# central-manager address 10.1.1.
Chapter 3 CLI Commands (config) clock (config) clock To set the summer daylight saving time and time zone for display purposes, use the clock global configuration command. To disable this function, use the no form of this command.
Chapter 3 CLI Commands (config) clock Device Modes application-accelerator central-manager Usage Guidelines Note To set and display the local and UTC current time of day without an NTP server, use the clock timezone command with the clock set command. The clock timezone parameter specifies the difference between UTC and local time, which is set with the clock set EXEC command. The UTC and local time are displayed with the show clock detail EXEC command.
Chapter 3 CLI Commands (config) clock Table 3-1 Time Zone—Offsets from UTC (continued) Time Zone Offset from UTC Asia/Dacca +6 Asia/Hong_Kong +8 Asia/Irkutsk +8 Asia/Jerusalem +2 Asia/Kabul +4.30 Asia/Karachi +5 Asia/Katmandu +5.45 Asia/Krasnoyarsk +7 Asia/Magadan +11 Asia/Muscat +4 Asia/New Delhi +5.30 Asia/Rangoon +6.30 Asia/Riyadh +3 Asia/Seoul +9 Asia/Singapore +8 Asia/Taipei +8 Asia/Tehran +3.
Chapter 3 CLI Commands (config) clock Table 3-1 Examples Time Zone—Offsets from UTC (continued) Time Zone Offset from UTC Europe/Prague +1 Europe/Warsaw +1 Japan +9 Pacific/Auckland +12 Pacific/Fiji +12 Pacific/Guam +10 Pacific/Kwajalein –12 Pacific/Samoa –11 US/Alaska –9 US/Central –6 US/Eastern –5 US/East-Indiana –5 US/Hawaii –10 US/Mountain –7 US/Pacific –8 The following example shows how to specify the local time zone as Pacific Standard Time with an offset of 8 hour
Chapter 3 CLI Commands (config) cms (config) cms To schedule maintenance and enable the Centralized Management System (CMS) on a WAAS device, use the cms global configuration command. To negate these actions, use the no form of this command.
Chapter 3 CLI Commands (config) cms Defaults incoming-wait 10-600 Specifies the maximum time to wait for a client response. The timeout period is in seconds. The default is 30 seconds. transfer 10-7200 Specifies the maximum time to allow a connection to remain open. The timeout period is in seconds. The default is 300 seconds.
Chapter 3 CLI Commands (config) cms Related Commands cms show cms Cisco Wide Area Application Services Command Reference 3-490 OL-21611-01
Chapter 3 CLI Commands (config) crypto pki (config) crypto pki To configure public key infrastructure (PKI) encryption parameters on a WAAS device, use the crypto pki global configuration command. To negate these actions, use the no form of this command. crypto pki {ca certificate-authority-name | global-settings} Syntax Description ca Configures encryption certificate authority information. Using this command enables certificate authority configuration mode.
Chapter 3 CLI Commands (config) crypto ssl (config) crypto ssl To configure secure sockets layer (SSL) encryption parameters on a WAAS device, use the crypto ssl global configuration command. To negate these actions, use the no form of this command.
Chapter 3 CLI Commands (config) crypto ssl WAE(config)# crypto ssl cipher-list mylist WAE(config-cipher-list)# The following example puts the WAAS device into SSL management service configuration mode. The mode change is indicated by the system prompt: WAE(config)# crypto ssl management-service WAE(config-ssl-mgmt)# The following example puts the WAAS device into SSL accelerated service configuration mode, editing the myservice accelerated service.
Chapter 3 CLI Commands (config) device mode (config) device mode To configure the device mode for the WAAS device, use the device mode global configuration command. To reset the mode of operation on your WAAS device, use the no form of this command. device mode {application-accelerator | central-manager} no device mode {application-accelerator | central-manager} Syntax Description application-accelerator Configures the WAAS device to function as a WAAS Accelerator.
Chapter 3 CLI Commands (config) device mode Related Commands show device-mode Cisco Wide Area Application Services Command Reference OL-21611-01 3-495
Chapter 3 CLI Commands (config) directed-mode (config) directed-mode To configure the mode by which traffic is sent between two WAEs, use the directed-mode global configuration command. To configure the WAAS device not to use directed mode, use the no form of this command. directed-mode enable [port udp-port] no directed-mode enable [port udp-port] Syntax Description enable Enables directed mode. port udp-port Sets the UDP port number to use to send traffic between two WAEs.
Chapter 3 CLI Commands (config) disk disk-name (config) disk disk-name To disable the disk for online removal, use the disk disk-name global configuration command. To reenable the disk, use the no form of this command. disk disk-name diskxx shutdown [force] no disk disk-name diskxx shutdown [force] Syntax Description diskxx Name of the disk (disk00-disk05). shutdown Disables the disk for maintenance. force (Optional) Forces a disk to be reenabled when used with the no form of this command.
Chapter 3 CLI Commands (config) disk disk-name (config) disk logical shutdown disk show disks Cisco Wide Area Application Services Command Reference 3-498 OL-21611-01
Chapter 3 CLI Commands (config) disk encrypt (config) disk encrypt To enable disk encryption, use the disk encrypt global configuration command. To disable disk encryption, use the no form of this command. disk encrypt enable no disk encrypt enable Syntax Description This command has no arguments or keywords. Defaults Disk encryption is disabled by default.
Chapter 3 CLI Commands (config) disk error-handling (config) disk error-handling To configure how disk errors are handled on a WAAS device, use the disk error-handling global configuration command. To disable automatic remapping of disk errors, use the no form of this command. disk error-handling remap no disk error-handling remap Syntax Description remap Defaults The disk is configured to remap disk errors automatically.
Chapter 3 CLI Commands (config) disk logical shutdown (config) disk logical shutdown To shut down the RAID-5 logical disk drive, use the disk logical shutdown global configuration command. To reenable the RAID-5 logical disk drive, use the no form of this command. disk logical shutdown no disk logical shutdown [force] Syntax Description force Defaults The RAID-5 array is configured by default.
Chapter 3 CLI Commands (config) disk object-cache extend (config) disk object-cache extend To enable extended object cache, use the disk object-cache global configuration command. To disable this feature, use the no form of this command. disk object-cache extend no disk object-cache extend Syntax Description This command has no arguments or keywords. Command Default No default behavior or values.
Chapter 3 CLI Commands (config) egress-method (config) egress-method To configure the egress method for intercepted connections, use the egress-method global configuration command. To unconfigure the egress method, use the no form of this command. egress-method {ip-forwarding | negotiated-return | generic-gre} intercept-method wccp no egress-method {ip-forwarding | negotiated-return | generic-gre} intercept-method wccp Syntax Description ip-forwarding Configures the IP forwarding egress method.
Chapter 3 CLI Commands (config) egress-method Related Commands clear arp-cache debug egress-method show egress-methods show tfo tcp (config) wccp tcp-promiscuous mask Cisco Wide Area Application Services Command Reference 3-504 OL-21611-01
Chapter 3 CLI Commands (config) end (config) end To exit global configuration mode, use the end global configuration command. end Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes global configuration Device Modes application-accelerator central-manager Usage Guidelines Use the end command to exit global configuration mode after completing any changes to the running configuration.
Chapter 3 CLI Commands (config) exec-timeout (config) exec-timeout To configure the length of time that an inactive Telnet or SSH session remains open on a WAAS device, use the exec-timeout global configuration command. To revert to the default value, use the no form of this command. exec-timeout timeout no exec-timeout timeout Syntax Description timeout Defaults The default is 15 minutes. Command Modes global configuration Device Modes application-accelerator Timeout in minutes (0–44640).
Chapter 3 CLI Commands (config) exit (config) exit To terminate global configuration mode and return to the privileged-level EXEC mode, use the exit command. exit Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes All modes Device Modes application-accelerator central-manager Usage Guidelines This command is equivalent to pressing Ctrl-Z or entering the end command.
Chapter 3 CLI Commands (config) flow monitor (config) flow monitor To enable network traffic flow monitoring and to register the WAE with the tcpstat-v1 collector for traffic analysis, use the flow monitor global configuration command. To disable the network traffic flow configuration, use the no form of this command. flow monitor tcpstat-v1 {enable | host ip_address} no flow monitor tcpstat-v1 {enable | host ip_address} Syntax Description tcpstat-v1 Sets the tcpstat-v1 collector configuration.
Chapter 3 CLI Commands (config) help (config) help To obtain online help for the command-line interface, use the help global configuration command. To disable help, use the no form of this command. help no help Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands (config) help shutdown slow-start tcp-promiscuous version Wccp Shutdown parameters accept load in slow-start mode TCP promiscuous mode service WCCP Version Number The following example shows how to use partial help to determine the syntax of a WCCP argument: WAE(config)# wccp tcp ? mask Specify mask used for CE assignment router-list-num Router list number Related Commands show running-config Cisco Wide Area Application Services Command Reference 3-510 OL-21611-01
Chapter 3 CLI Commands (config) hostname (config) hostname To configure the network hostname on a WAAS device, use the hostname global configuration command. To reset the hostname to the default setting, use the no form of this command. hostname name no hostname name Syntax Description name Defaults The default hostname is the model number of the WAAS device (for example WAE-612 or WAE-7371).
Chapter 3 CLI Commands (config) hostname show hosts Cisco Wide Area Application Services Command Reference 3-512 OL-21611-01
Chapter 3 CLI Commands (config) inetd (config) inetd To enable FTP and RCP services on a WAAS device, use the inetd enable global configuration command. To disable these same services, use the no form of this command. inetd enable {ftp | rcp} no inetd enable {ftp | rcp} Syntax Description enable Enables services. ftp Enables FTP services. rcp Enables RCP services. Defaults FTP is enabled; RCP is disabled.
Chapter 3 CLI Commands (config) inline vlan-id-connection-check (config) inline vlan-id-connection-check To enable VLAN ID checking on intercepted traffic, use the inline vlan-id-connection-check global configuration command. To disable VLAN ID checking, use the no form of this command. inline vlan-id-connection-check no inline vlan-id-connection-check Syntax Description This command has no arguments or keywords. Defaults VLAN ID checking is enabled.
Chapter 3 CLI Commands (config) interception access-list (config) interception access-list To configure traffic interception with an access list, use the interception access-list global configuration command. To disable the interception access list, use the no form of this command. interception access-list {acl-num | acl_name} no interception access-list Syntax Description acl_num Numeric identifier that identifies the ACL to apply to traffic interception.
Chapter 3 CLI Commands (config) interception access-list dc-wae(config-ext-nacl)# exit dc-wae(config)# interception access-list iacl Related Commands (config) bypass (config) ip access-list Cisco Wide Area Application Services Command Reference 3-516 OL-21611-01
Chapter 3 CLI Commands (config) interface GigabitEthernet (config) interface GigabitEthernet To configure a Gigabit Ethernet interface, use the interface global configuration command. To disable selected options, restore default values, or enable a shutdown interface, use the no form of this command.
Chapter 3 CLI Commands (config) interface GigabitEthernet in Applies the specified ACL to inbound packets on the current interface. out Applies the specified ACL to outbound packets on the current interface. address ip-address netmask Sets the interface IP address and netmask. secondary (Optional) Specifies that the configured address is a secondary IP address. If this keyword is omitted, the configured address is the primary IP address.
Chapter 3 CLI Commands (config) interface GigabitEthernet Configuring Multiple Secondary IP Addresses on a Single Physical Interface Use the interface secondary global configuration command to configure more than one IP address on the same interface. By configuring multiple IP addresses on a single interface, the WAAS device can be present in more than one subnet.
Chapter 3 CLI Commands (config) interface GigabitEthernet have not made it the primary interface, you cannot specify the command again to add the primary designation. First, remove the interface from the standby group, then reassign it, specifying the primary option at the same time. A physical interface can be a member of a standby group or a port channel, but not both. You cannot assign an IP address to both a standby group and a port channel.
Chapter 3 CLI Commands (config) interface GigabitEthernet Related Commands show interface show running-config show startup-config Cisco Wide Area Application Services Command Reference OL-21611-01 3-521
Chapter 3 CLI Commands (config) interface InlineGroup (config) interface InlineGroup To configure an InlineGroup interface, use the interface global configuration command. To disable selected options, restore default values, or enable a shutdown interface, use the no form of this command.
Chapter 3 CLI Commands (config) interface InlineGroup access-group Configures access control for IP packets on this interface using access control list (ACL). acl_num Numeric identifier that identifies the ACL to apply to the current interface. For standard ACLs, the valid range is 1–99; for extended ACLs, the valid range is 100–199. acl_name Alphanumeric identifier of up to 30 characters, beginning with a letter that identifies the ACL to apply to the current interface.
Chapter 3 CLI Commands (config) interface InlineGroup Related Commands show interface show running-config show startup-config Cisco Wide Area Application Services Command Reference 3-524 OL-21611-01
Chapter 3 CLI Commands (config) interface PortChannel (config) interface PortChannel To configure a port-channel interface, use the interface global configuration command. To disable selected options, restore default values, or enable a shutdown interface, use the no form of this command.
Chapter 3 CLI Commands (config) interface PortChannel Note You cannot use the inline Ethernet interfaces that are located on the WAE inline network adapter to form an EtherChannel. Note No two interfaces can have IP addresses in the same subnet. Examples The following example shows how to create an EtherChannel. The port channel is port channel 1 and is assigned an IP address of 10.10.10.10 and a netmask of 255.0.0.0: WAE# configure WAE(config)# interface PortChannel 1 WAE(config-if)# ip address 10.
Chapter 3 CLI Commands (config) interface standby (config) interface standby To configure a standby interface, use the interface standby global configuration command. To disable selected options, restore default values, or enable a shutdown interface, use the no form of this command.
Chapter 3 CLI Commands (config) ip (config) ip To change the initial network device configuration settings, use the ip global configuration command. To delete or disable these settings, use the no form of this command.
Chapter 3 CLI Commands (config) ip To add an entry to the /etc/hosts file on the device, mapping a hostname to an IP address, use the ip host command. A given hostname can be mapped only to a single IP address, while an IP address can have multiple hostnames mapped to it, each one through a separate issuance of this command. To remove the entry from the /etc/hosts file, use the no form of this command. You can use the show hosts EXEC command to display the contents of the /etc/hosts file.
Chapter 3 CLI Commands (config) ip access-list (config) ip access-list To create and modify access lists on a WAAS device for controlling access to interfaces or applications, use the ip access-list global configuration command. To disable an access list, use the no form of this command.
Chapter 3 CLI Commands (config) ip access-list Usage Guidelines Within ACL configuration mode, you can use the editing commands (list, delete, and move) to display the current condition entries, to delete a specific entry, or to change the order in which the entries will be evaluated. To return to global configuration mode, use the exit command at the ACL configuration mode prompt.
Chapter 3 CLI Commands (config) ip access-list interface GigabitEthernet 1/0 ip address 10.1.1.50 255.255.0.0 ip access-group example in exit . . . ip access-list extended example permit tcp any any eq www permit tcp host 10.1.1.5 any eq ssh exit . . .
Chapter 3 CLI Commands (config) kerberos (config) kerberos To authenticate a user that is defined in the Kerberos database, use the kerberos global configuration command. To disable authentication, use the no form of this command.
Chapter 3 CLI Commands (config) kerberos Note Your Windows domain server must have a Reverse DNS Zone configured for this command to execute successfully. The KDC server and all hosts with Kerberos authentication configured must interact within a 5-minute window or authentication will fail. All hosts, especially the KDC, should be running NTP. For information about configuring NTP, see the (config) ntp command. The KDC server and Admin server must have the same IP address.
Chapter 3 CLI Commands (config) kernel kdb (config) kernel kdb To enable access to the kernel debugger (kdb), use the kernel kdb global configuration command. To disable access to the kernel debugger, use the no form of this command. kernel kdb no kernel kdb Syntax Description This command has no arguments or keywords. Defaults The kernel debugger is disabled by default.
Chapter 3 CLI Commands (config) kernel kdump (config) kernel kdump To enable the kernel crash dump mechanism, use the kernel kdump enable global configuration command. To disable the kernel crash dump mechanism, use the no form of this command. kernel kdump enable no kernel kdump enable Syntax Description This command has no arguments or keywords. Defaults The kernel crash dump mechanism is enabled by default.
Chapter 3 CLI Commands (config) line (config) line To specify terminal line settings, use the line global configuration command. To configure the WAAS device to not check for the carrier detect signal, use the no form of this command. line console carrier-detect no line console carrier-detect Syntax Description console Configures the console terminal line settings. carrier-detect Sets the device to check the carrier detect signal before writing to the console.
Chapter 3 CLI Commands (config) logging console (config) logging console To set system logging to console, use the logging console global configuration command. To disable logging functions, use the no form of this command. logging console {enable | priority loglevel} no logging console {enable | priority loglevel} Syntax Description Defaults console Sets system logging to a console. enable Enables system logging. priority loglevel Sets which priority level messages to send.
Chapter 3 CLI Commands (config) logging console The following example shows how to disable sending of messages that have a priority code of “error” (level 3) to the console: WAE(config)# no logging console error Related Commands clear arp-cache show logging Cisco Wide Area Application Services Command Reference OL-21611-01 3-539
Chapter 3 CLI Commands (config) logging disk (config) logging disk To system logging to a disk file, use the logging disk global configuration command. To disable logging functions, use the no form of this command. logging disk {enable | filename filename | priority loglevel | recycle size} no logging disk {enable | filename filename | priority loglevel | recycle size} Syntax Description disk Sets system logging to a disk file. enable Enables system logging.
Chapter 3 CLI Commands (config) logging disk The no logging disk recycle size command sets the file size to the default value. Whenever the current log file size surpasses the recycle size, the log file is rotated. The log file cycles through at most five rotations, and they are saved as [log file name].[1-5] under the same directory as the original log. The rotated log file is the one configured using the logging disk filename command.
Chapter 3 CLI Commands (config) logging facility (config) logging facility To set the facility parameter for system logging, use the logging facility global configuration command. To disable logging functions, use the no form of this command. logging facility facility no logging facility facility Syntax Description facility facility Defaults Logging: on Command Modes global configuration Device Modes application-accelerator Sets the facility parameter for syslog messages.
Chapter 3 CLI Commands (config) logging facility Related Commands clear arp-cache show logging Cisco Wide Area Application Services Command Reference OL-21611-01 3-543
Chapter 3 CLI Commands (config) logging host (config) logging host To configure system logging to a remote host, use the logging host global configuration command. To disable logging functions, use the no form of this command. logging host {hostname | ip-address} [port port_num | priority loglevel | rate-limit message_rate] no logging host {hostname | ip-address} [port port_num | priority loglevel | rate-limit message_rate] Syntax Description host Sets system logging to a remote host.
Chapter 3 CLI Commands (config) logging host Usage Guidelines Use the logging command to set specific parameters of the system log file. To configure the WAAS device to send varying levels of event messages to an external syslog host, use the logging host option. You can configure a WAAS device to send varying levels of messages to up to four remote syslog hosts using the logging host hostname command.
Chapter 3 CLI Commands (config) ntp (config) ntp To configure the NTP server and to allow the system clock to be synchronized by a time server, use the ntp global configuration command. To disable this function, use the no form of this command.
Chapter 3 CLI Commands (config) ntp Usage Guidelines Note Examples Unexpected time changes can result in unexpected system behavior. We recommend reloading the system after enabling an NTP server. The following example shows how to specify the NTP server IP address as the time source for a WAAS device. It also removes this configuration. WAE(config)# ntp 172.16.22.44 WAE(config)# no ntp 172.16.22.
Chapter 3 CLI Commands (config) peer (config) peer To enable peer optimization, use the peer global configuration command. To disable peer optimization, use the no form of this command. peer device-id deviceid [description description] optimization enable no peer device-id deviceid [description description] optimization enable Syntax Description device-id deviceid Configures the device ID of the peer device with which to enable or disable optimization.
Chapter 3 CLI Commands (config) policy-engine application classifier (config) policy-engine application classifier To create or edit an existing application classifier on a WAE, use the policy-engine application classifier global configuration command. To delete an application classifier or a condition, use the no form of this command.
Chapter 3 CLI Commands (config) policy-engine application classifier The WAAS software comes with over 150 default application policies that help your WAAS system classify and optimize some of the most common traffic on your network. Before you create a new application policy, we recommend that you review the default policies and modify them as appropriate. It is usually easier to modify an existing policy than to create a new one.
Chapter 3 CLI Commands (config) policy-engine application map adaptor EPM (config) policy-engine application map adaptor EPM To configure the application policy with advanced policy map lists of the EndPoint Mapper (EPM) service on a WAE, use the policy-engine application map adaptor EPM global configuration command. To disable the EPM service in the application policy configuration, use the no form of this command.
Chapter 3 CLI Commands (config) policy-engine application map adaptor EPM LZ Applies LZ compression. none Applies no compression. full Applies full generic optimization. pass-through Allows traffic to pass through without any optimization. accelerate (Optional) Accelerates the traffic using a special adapter. cifs Accelerates the traffic using the CIFS accelerator. http Accelerates the traffic using the HTTP accelerator. mapi Accelerates the traffic using the MAPI accelerator.
Chapter 3 CLI Commands (config) policy-engine application map adaptor WAFS transport (config) policy-engine application map adaptor WAFS transport To configure application policies with the Wide Area File Services (WAFS) transport option, use the policy-engine application map adaptor WAFS transport global configuration command. To disable the WAFS transport policy map in the application policy configuration, use the no form of this command.
Chapter 3 CLI Commands (config) policy-engine application map adaptor WAFS transport accelerate (Optional) Accelerates the traffic using a special adapter. cifs Accelerates the traffic using the CIFS accelerator. http Accelerates the traffic using the HTTP accelerator. mapi Accelerates the traffic using the MAPI accelerator. MS-port-mapper Accelerates the traffic using the Microsoft EndPoint Port Mapper (EPM). nfs Accelerates the traffic using the NFS accelerator.
Chapter 3 CLI Commands (config) policy-engine application map basic (config) policy-engine application map basic To configure the application policy with the basic policy map, use the policy-engine application map basic global configuration command. To disable the EPM service in the application policy configuration, use the no form of this command.
Chapter 3 CLI Commands (config) policy-engine application map basic cifs Accelerates the traffic using the CIFS accelerator. http Accelerates the traffic using the HTTP accelerator. mapi Accelerates the traffic using the MAPI accelerator. MS-port-mapper Accelerates the traffic using the Microsoft EndPoint Port Mapper (EPM). nfs Accelerates the traffic using the NFS accelerator. video Accelerates the traffic using the video accelerator.
Chapter 3 CLI Commands (config) policy-engine application map basic show policy-engine application Cisco Wide Area Application Services Command Reference OL-21611-01 3-557
Chapter 3 CLI Commands (config) policy-engine application map other optimize DRE (config) policy-engine application map other optimize DRE To configure the optimize DRE action on nonclassified traffic on a WAE, use the policy-engine application map other optimize DRE global configuration command. policy-engine application map other optimize DRE {yes | no} compression {LZ | none} [set-dscp dscp-marking] Syntax Description yes Applies the optimize DRE action on nonclassified traffic.
Chapter 3 CLI Commands (config) policy-engine application map other optimize DRE (config) policy-engine application name (config) policy-engine application set-dscp Cisco Wide Area Application Services Command Reference OL-21611-01 3-559
Chapter 3 CLI Commands (config) policy-engine application map other optimize full (config) policy-engine application map other optimize full To configure the application policy on nonclassified traffic with the optimize full action, use the policy-engine application map other optimize full global configuration command.
Chapter 3 CLI Commands (config) policy-engine application map other pass-through (config) policy-engine application map other pass-through To configure the application policy on nonclassified traffic with the pass-through action on a WAE, use the policy-engine application map other pass-through global configuration command. policy-engine application map other pass-through Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands (config) policy-engine application name (config) policy-engine application name To create a new application definition that specifies general information about an application on a WAE, use the policy-engine application name global configuration command. To delete the application definition, use the no form of this command.
Chapter 3 CLI Commands (config) policy-engine application name WAE(config)# policy-engine application name Payroll The following example shows how to assign a DSCP marking value to traffic associated with the Payroll application: WAE(config)# policy-engine application name Payroll set-dscp cs1 Related Commands (config) policy-engine application classifier (config) policy-engine application map adaptor EPM (config) policy-engine application map adaptor WAFS transport (config) policy-engine application m
Chapter 3 CLI Commands (config) policy-engine application set-dscp (config) policy-engine application set-dscp To set the default DSCP marking value for use with applications, use the policy-engine application set-dscp global configuration command. To set the default DSCP marking value to its default value, use the no form of this command.
Chapter 3 CLI Commands (config) policy-engine application set-dscp Table 3-2 DSCP Code af43 cs1 cs2 cs3 cs4 cs5 cs6 cs7 copy default ef Examples DSCP Marking Values (continued) Description Sets packets with AF43 dscp (100110). Sets packets with CS1 (precedence 1) dscp (001000). Sets packets with CS2 (precedence 2) dscp (010000). Sets packets with CS3 (precedence 3) dscp (011000). Sets packets with CS4 (precedence 4) dscp (100000). Sets packets with CS5 (precedence 5) dscp (101000).
Chapter 3 CLI Commands (config) policy-engine config (config) policy-engine config To remove application policy configurations or replace application policy configurations with factory defaults on a WAE, use the policy-engine config global configuration command. policy-engine config {remove-all | restore-predefined} Syntax Description remove-all Removes the application policy configurations and resets other changed configurations.
Chapter 3 CLI Commands (config) policy-engine config show statistics auto-discovery show statistics connection closed Cisco Wide Area Application Services Command Reference OL-21611-01 3-567
Chapter 3 CLI Commands (config) port-channel (config) port-channel To configure the port channel load-balancing options on a WAAS device, use the port-channel global configuration command. To set load balancing on the port channel to its default method, use the no form of this command. port-channel load-balance {src-dst-ip-port | round-robin} no port-channel load-balance {src-dst-ip-port | round-robin} Syntax Description load-balance Configures the load-balancing method.
Chapter 3 CLI Commands (config) primary-interface (config) primary-interface To configure the primary interface for a WAAS device, use the primary-interface global configuration command. To remove the configured primary interface, use the no form of this command.
Chapter 3 CLI Commands (config) primary-interface Examples The following example shows how to specify the Gigabit Ethernet slot 1, port 0 as the primary interface on a WAAS device: WAE(config)# primary-interface GigabitEthernet 1/0 The following example shows how to specify the Gigabit Ethernet slot 2, port 0 as the primary interface on a WAAS device: WAE(config)# primary-interface GigabitEthernet 2/0 The following example shows how to specify the inline interface slot 1, group 0 as the primary interf
Chapter 3 CLI Commands (config) print-services (config) print-services To enable legacy print services and designate a group name for administrators who are allowed configuration access on a WAAS device, use the print-services global configuration command. To disable print services on a WAAS device or to clear the administrative group, use the no form of this command.
Chapter 3 CLI Commands (config) print-services The print-services administrator group is removed successfully. Please restart print services for the change to take effect.
Chapter 3 CLI Commands (config) radius-server (config) radius-server To configure a set of RADIUS authentication server settings on the WAAS device, use the radius-server global configuration command. To disable RADIUS authentication server settings, use the no form of this command.
Chapter 3 CLI Commands (config) radius-server WAE(config)# radius-server host 172.16.90.
Chapter 3 CLI Commands (config) smb-conf (config) smb-conf To manually configure the parameters for a WAAS device Samba configuration file, smb.conf, use the smb-conf global configuration command. To return a parameter to its default value, use the no form of this command.
Chapter 3 CLI Commands (config) smb-conf Table 3-3 Print-Related Parameters Parameter Name Default Value Parameter Description idmap uid 70000-200000 Range of user IDs allocated for mapping UNIX users to NT user SIDs. idmap gid 70000-200000 Range of group IDs allocated for mapping UNIX groups to NT group SIDs. winbind enum users no Parameter that does not enumerate domain users using MSRPC. winbind enum groups no Parameter that does not enumerate domain groups using MSRPC.
Chapter 3 CLI Commands (config) smb-conf Table 3-3 Print-Related Parameters (continued) Parameter Name Default Value Parameter Description netbios name MYFILEENGINE Name of the Samba server hosting print services. This parameter can also be set by the windows-domain netbios-name command. realm CISCO Active Directory domain name. Always uppercase. This parameter can also be set by the windows-domain realm command. wins server 10.10.10.
Chapter 3 CLI Commands (config) smb-conf Table 3-3 Print-Related Parameters (continued) Parameter Name Default Value Parameter Description printable yes Parameter that allows connected clients to open, write to and submit spool files into the directory specified with the path parameter for printing. Used by Samba to differentiate printer shares from file shares. If this is set to no, printing is not allowed.
Chapter 3 CLI Commands (config) snmp-server access-list (config) snmp-server access-list To configure a standard access control list on a WAAS device to allow access through an SNMP agent, use the snmp-server access-list global configuration command. To remove a standard access control list, use the no form of this command. snmp-server access-list {num | name} no snmp-server access-list {num | name} Syntax Description num Standard access list number (1–99). name Standard access list name.
Chapter 3 CLI Commands (config) snmp-server community (config) snmp-server community To enable the SNMP agent on a WAAS device and to set up the community access string to permit access to the SNMP agent, use the snmp-server community global configuration command. To disable the SNMP agent and remove the previously configured community string, use the no form of this command.
Chapter 3 CLI Commands (config) snmp-server community (config) snmp-server notify inform (config) snmp-server user (config) snmp-server view snmp trigger Cisco Wide Area Application Services Command Reference OL-21611-01 3-581
Chapter 3 CLI Commands (config) snmp-server contact (config) snmp-server contact To set the system server contact string on a WAAS device, use the snmp-server contact global configuration command. To remove the system contact information, use the no form of this command. snmp-server contact line no snmp-server contact line Syntax Description contact line Command Modes global configuration Device Modes application-accelerator Specifies the text for MIB-II object sysContact.
Chapter 3 CLI Commands (config) snmp-server enable traps (config) snmp-server enable traps To enable the WAAS device to send SNMP traps, use the snmp-server enable traps global configuration command. To disable all SNMP traps or only SNMP authentication traps, use the no form of this command.
Chapter 3 CLI Commands (config) snmp-server enable traps Defaults This command is disabled by default. No traps are enabled.
Chapter 3 CLI Commands (config) snmp-server enable traps WAE(config)# no snmp-server enable traps Related Commands (config) snmp-server community (config) snmp-server contact (config) snmp-server group (config) snmp-server host (config) snmp-server location (config) snmp-server mib (config) snmp-server notify inform (config) snmp-server user (config) snmp-server view snmp trigger Cisco Wide Area Application Services Command Reference OL-21611-01 3-585
Chapter 3 CLI Commands (config) snmp-server group (config) snmp-server group To define a user security model group for a WAAS device, use the snmp-server group global configuration command. To remove the specified group, use the no form of this command.
Chapter 3 CLI Commands (config) snmp-server group Select one of three SNMP security model groups: Version 1 (v1) Security Model, Version 2c (v2c) Security Model, or the User Security Model (v3 or SNMPv3). Optionally, you then specify a notify, read, or write view for the group for the particular security model chosen. The v3 option allows you to specify the group using one of three security levels: auth (AuthNoPriv Security Level), noauth (noAuthNoPriv Security Level), or priv (AuthPriv Security Level).
Chapter 3 CLI Commands (config) snmp-server host (config) snmp-server host To specify the recipient of a host SNMP trap operation, use the snmp-server host global configuration command. To remove the specified host, use the no form of this command.
Chapter 3 CLI Commands (config) snmp-server host Usage Guidelines If you do not enter an snmp-server host command, no traps are sent. To configure the WAAS device to send SNMP traps, you must enter at least one snmp-server host command. To enable multiple hosts, you must enter a separate snmp-server host command for each host. The maximum number of snmp-server host commands is four. When multiple snmp-server host commands are given for the same host, the community string in the last command is used.
Chapter 3 CLI Commands (config) snmp-server location (config) snmp-server location To set the SNMP system location string on a WAAS device, use the snmp-server location global configuration command. To remove the location string, use the no form of this command. snmp-server location line no snmp-server location line Syntax Description location line Defaults No system location string is set.
Chapter 3 CLI Commands (config) snmp-server mib (config) snmp-server mib To configure persistence for the SNMP Event MIB, use the snmp-server mib global configuration command. To disable the Event MIB, use the no form of this command. snmp-server mib persist event no snmp-server mib persist event Syntax Description persist Configures MIB persistence. event Enables MIB persistence for the Event MIB. Defaults No default behavior or values.
Chapter 3 CLI Commands (config) snmp-server mib Note Examples • SNMPv2 • SNMP-VACM-MIB The WAAS software supports six generic alarm traps in the CISCO-CONTENT-ENGINE-MIB for SNMP and Node Health Manager integration.
Chapter 3 CLI Commands (config) snmp-server notify inform (config) snmp-server notify inform To configure the SNMP notify inform request on a WAAS device, use the snmp-server notify inform global configuration command. To return the setting to the default value, use the no form of this command. snmp-server notify inform no snmp-server notify inform Syntax Description This command has no arguments or keywords.
Chapter 3 CLI Commands (config) snmp-server trap-source (config) snmp-server trap-source To set the source interface from which SNMP traps are sent on a WAAS device, use the snmp-server trap-source global configuration command. To remove the trap source configuration, use the no form of this command.
Chapter 3 CLI Commands (config) snmp-server user (config) snmp-server user To define a user who can access the SNMP server, use the snmp-server user global configuration command. To remove access, use the no form of this command.
Chapter 3 CLI Commands (config) snmp-server user central-manager Examples The following example shows how to create an SNMPv3 user account on the WAAS device. The SNMPv3 user is named acme and belongs to the group named admin. Because this SNMP user account has been set up with no authentication password, the SNMP agent on the WAAS device does not perform authentication on SNMP requests from this user.
Chapter 3 CLI Commands (config) snmp-server view (config) snmp-server view To define an SNMPv2 MIB view on a WAAS device, use the snmp-server view global configuration command. To remove the MIB view definition, use the no form of this command. snmp-server view viewname MIBfamily {excluded | included} no snmp-server view viewname MIBfamily {excluded | included} Syntax Description viewname MIBfamily Name of this family of view subtrees and a subtree of the MIB. You can enter a maximum of 64 characters.
Chapter 3 CLI Commands (config) sshd (config) sshd To enable the SSH daemon on a WAAS device, use the sshd global configuration command. To disable the SSH daemon on a WAAS device, use the no form of this command.
Chapter 3 CLI Commands (config) sshd central-manager Usage Guidelines Before you enable the sshd command, use the ssh-key-generate command to generate a private and a public host key, which the client uses to verify the server identity.
Chapter 3 CLI Commands (config) sshd Related Commands (config) ssh-key-generate Cisco Wide Area Application Services Command Reference 3-600 OL-21611-01
Chapter 3 CLI Commands (config) ssh-key-generate (config) ssh-key-generate To generate the SSH host key for a WAAS device, use the ssh-key-generate global configuration command. To remove the SSH key, use the no form of this command.
Chapter 3 CLI Commands (config) tacacs (config) tacacs To configure TACACS+ server parameters on a WAAS device, use the tacacs global configuration command. To disable individual options, use the no form of this command.
Chapter 3 CLI Commands (config) tacacs You can use the TACACS+ remote database to maintain login and configuration privileges for administrative users. The tacacs host command allows you to configure the network parameters required to access the remote database. Use the tacacs key command to specify the TACACS+ key, used to encrypt the packets transmitted to the server. This key must be the same as the one specified on the server daemon.
Chapter 3 CLI Commands (config) tacacs Server ---------------------------10.107.192.148 10.107.192.168 10.77.140.77 Status -----primary You can configure the password type to be ASCII using the tacacs password ascii command. You can then verify the changes using the show tacacs command.
Chapter 3 CLI Commands (config) tcp (config) tcp To configure TCP parameters on a WAAS device, use the tcp global configuration command. To disable TCP parameters, use the no form of this command.
Chapter 3 CLI Commands (config) tcp Usage Guidelines Caution The following are the usage guidelines for this command: Be careful using these parameters. In nearly all environments, the default TCP settings are adequate. Fine tuning of TCP settings is for network administrators who are experienced and have a full understanding of TCP operation details. See the Cisco Wide Area Application Services Configuration Guide for more information.
Chapter 3 CLI Commands (config) telnet enable (config) telnet enable To enable Telnet on a WAAS device, use the telnet enable global configuration command. To disable this feature, use the no form of this command. telnet enable no telnet enable Syntax Description This command has no arguments or keywords. Defaults By default, the Telnet service is enabled on a WAAS device.
Chapter 3 CLI Commands (config) tfo exception (config) tfo exception To configure exception handling for Traffic Flow Optimization (TFO), use the tfo exception global configuration command. To disable TFO exception handling configuration, use the no form of this command. tfo exception {coredump | debug | no-coredump} no tfo exception {coredump | debug | no-coredump} Syntax Description coredump Writes a core file (default). debug Hangs the system until it is explicitly restarted.
Chapter 3 CLI Commands (config) tfo optimize (config) tfo optimize To configure a WAE for Traffic Flow Optimization (TFO), use the tfo optimize global configuration command. To disable TFO optimization, use the no form of this command. tfo optimize {DRE {yes | no} compression {LZ | none} | full} no tfo optimize {DRE {yes | no} compression {LZ | none} | full} Syntax Description DRE Configures TFO optimization with or without Data Redundancy Elimination (DRE). yes Enables DRE. no Disables DRE.
Chapter 3 CLI Commands (config) tfo tcp adaptive-buffer-sizing (config) tfo tcp adaptive-buffer-sizing To configure a WAE for Traffic Flow Optimization (TFO) with TCP adaptive buffering, use the tfo tcp adaptive-buffer-sizing global configuration command. To disable adaptive buffer sizing or to unconfigure the buffer size, use the no form of this command.
Chapter 3 CLI Commands (config) tfo tcp keepalive (config) tfo tcp keepalive To configure a WAE for Traffic Flow Optimization (TFO) with TCP keepalives, use the tfo tcp keepalive global configuration command. To disable TFO TCP keepalives, use the no form of this command. tfo tcp keepalive no tfo tcp keepalive Syntax Description This command has no arguments or keywords. Defaults Keepalives are disabled by default.
Chapter 3 CLI Commands (config) tfo tcp optimized-mss (config) tfo tcp optimized-mss To configure a WAE for Traffic Flow Optimization (TFO) with an optimized-side TCP maximum segment size, use the tfo tcp optimized-mss global configuration command. To disable this function, use the no form of this command. tfo tcp optimized-mss segment-size no tfo tcp optimized-mss segment-size Syntax Description segment-size Defaults The default value of the segment size is 1432 bytes.
Chapter 3 CLI Commands (config) tfo tcp optimized-receive-buffer (config) tfo tcp optimized-receive-buffer To configure a WAE for Traffic Flow Optimization (TFO) with an optimized-side receive buffer, use the tfo tcp optimized-receive-buffer global configuration command. To disable this function, use the no form of this command.
Chapter 3 CLI Commands (config) tfo tcp optimized-send-buffer (config) tfo tcp optimized-send-buffer To configure a WAE for Traffic Flow Optimization (TFO) with an optimized-side send buffer, use the tfo tcp optimized-send-buffer global configuration command. To disable this function, use the no form of this command.
Chapter 3 CLI Commands (config) tfo tcp original-mss (config) tfo tcp original-mss To configure a WAE for Traffic Flow Optimization (TFO) with an unoptimized-side TCP maximum segment size, use the tfo tcp original-mss global configuration command. To disable this function, use the no form of this command.
Chapter 3 CLI Commands (config) tfo tcp original-receive-buffer (config) tfo tcp original-receive-buffer To configure a WAE for Traffic Flow Optimization (TFO) with an unoptimized-side receive buffer, use the tfo tcp original-receive-buffer global configuration command. To disable this function, use the no form of this command.
Chapter 3 CLI Commands (config) tfo tcp original-send-buffer (config) tfo tcp original-send-buffer To configure a WAE for Traffic Flow Optimization (TFO) with an unoptimized-side send buffer, use the tfo tcp original-send-buffer global configuration command. To disable this function, use the no form of this command.
Chapter 3 CLI Commands (config) transaction-logs (config) transaction-logs To configure and enable transaction logging on a WAE, use the transaction-logs global configuration command. To disable a transaction logging option, use the no form of this command.
Chapter 3 CLI Commands (config) transaction-logs every-day Archives using intervals of 1 day or less. at hour:minute Specifies the local time at which to archive each day (hh:mm). every hours Specifies the interval in hours. The interval aligns with midnight. The intervals are as follows: 1 12 2 24 3 4 6 8 Hourly Every 12 hours Every 2 hours Every 24 hours Every 3 hours Every 4 hours Every 6 hours Every 8 hours every-hour Specifies intervals of 1 hour or less.
Chapter 3 CLI Commands (config) transaction-logs Defaults interval minutes Specifies the interval in minutes (1–10080) at which to export a file. sftp-server Sets the Secure File Transfer Protocol (SFTP) server to receive exported archived files.
Chapter 3 CLI Commands (config) username (config) username To establish username authentication on a WAAS device, use the username global configuration command. To disable this feature, use the no form of this command.
Chapter 3 CLI Commands (config) username Usage Guidelines Note We strongly recommend that you use the WAAS Central Manager GUI instead of the WAAS CLI to configure passwords and privilege levels for users on your WAAS devices, if possible. For information about how to use the WAAS Central Manager GUI to centrally configure and administer users on a single WAE or group of WAEs, which are registered with a WAAS Central Manager, see the Cisco Wide Area Application Services Configuration Guide.
Chapter 3 CLI Commands (config) virtual-blade (config) virtual-blade To configure virtual blades on your WAAS device, use the virtual-blade global configuration command. To negate these actions, use the no form of this command. virtual-blade {virtual-blade-number | enable} no virtual-blade {virtual-blade-number | enable} Syntax Description virtual-blade-number Number of the virtual blade that you want to edit.
Chapter 3 CLI Commands (config) virtual-blade WAE(config-vb)# Related Commands show virtual-blade (config-vb) autostart (config-vb) boot (config-vb) cpu-list (config-vb) description (config-vb) device (config-vb) disk (config-vb) interface (config-vb) memory (config-vb) vnc Cisco Wide Area Application Services Command Reference 3-624 OL-21611-01
Chapter 3 CLI Commands (config) wccp access-list (config) wccp access-list To configure an IP access list on a WAE for inbound WCCP GRE encapsulated traffic, use the wccp access-list global configuration command. To disable this feature, use the no form of this command. wccp access-list {acl-number | ext-acl-number | acl-name} no wccp access-list {acl-number | ext-acl-number | acl-name} Syntax Description acl-number Standard IP access list number (1–99).
Chapter 3 CLI Commands (config) wccp access-list (implicit deny any: 0 matches) total invocations: 0 Extended IP access list 100 1 permit icmp any any (implicit fragment permit: 0 matches) (implicit deny ip any any: 0 matches) total invocations: 0 Extended IP access list 101 1 permit ip any any (implicit fragment permit: 0 matches) (implicit deny ip any any: 0 matches) total invocations: 0 Extended IP access list 102 1 permit icmp 0.0.1.1 255.255.0.
Chapter 3 CLI Commands (config) wccp access-list Packets received too small: Packets dropped due to zero TTL: Packets dropped due to bad buckets: Packets dropped due to no redirect address: Packets dropped due to loopback redirect: Connections bypassed due to load: Packets sent back to router: Packets sent to another CE: GRE fragments redirected: Packets failed GRE encapsulation: Packets dropped due to invalid fwd method: Packets dropped due to insufficient memory: Packets bypassed, no conn at all: Packet
Chapter 3 CLI Commands (config) wccp flow-redirect (config) wccp flow-redirect To enable WCCP flow redirection on a WAE, use the wccp flow-redirect global configuration command. To disable flow redirection, use the no form of this command.
Chapter 3 CLI Commands (config) wccp router-list (config) wccp router-list To configure a router list for WCCP Version 2, use the wccp router-list global configuration command. To disable this function, use the no form of this command. wccp router-list number ip-address no wccp router-list number ip-address Syntax Description number Router list number (1–8). ip-address IP address of the router to add to the list.
Chapter 3 CLI Commands (config) wccp router-list Related Commands (config) wccp version Cisco Wide Area Application Services Command Reference 3-630 OL-21611-01
Chapter 3 CLI Commands (config) wccp shutdown (config) wccp shutdown To set the maximum time interval after which the WAE will perform a clean shutdown of the WCCP, use the wccp shutdown global configuration command. To disable the clean shutdown, use the no form of this command. wccp shutdown max-wait seconds no wccp shutdown max-wait seconds Syntax Description max-wait seconds Defaults The maximum time interval before a clean shutdown is 120 seconds by default.
Chapter 3 CLI Commands (config) wccp shutdown Related Commands (config) wccp flow-redirect (config) wccp version Cisco Wide Area Application Services Command Reference 3-632 OL-21611-01
Chapter 3 CLI Commands (config) wccp tcp-promiscuous mask (config) wccp tcp-promiscuous mask To configure the Web Cache Coordination Protocol (WCCP) Version 2 TCP promiscuous mode service (WCCP Version 2 services 61 and 62) mask on a WAE, use the wccp tcp-promiscuous mask global configuration command. To disable this function, use the no form of this command.
Chapter 3 CLI Commands (config) wccp tcp-promiscuous router-list-num (config) wccp tcp-promiscuous router-list-num To configure the Web Cache Coordination Protocol (WCCP) Version 2 TCP promiscuous mode service (WCCP Version 2 services 61 and 62) on a WAE, use the wccp tcp-promiscuous router-list-num global configuration command. To disable this function, use the no form of this command.
Chapter 3 CLI Commands (config) wccp tcp-promiscuous router-list-num Usage Guidelines Note Examples To configure the egress method for WCCP intercepted connections, use the egress-method global configuration command. WCCP works with IPv4 networks only. The following example shows how to turn on the TCP promiscuous mode service and associate this service with the router list: WAE # wccp tcp-promiscuous router-list-num 1 WCCP configuration for TCP Promiscuous service 61 succeeded.
Chapter 3 CLI Commands (config) wccp version (config) wccp version To specify the version of WCCP that the WAE should use, enter the wccp version global configuration command. To disable the currently running version, use the no form of this command. wccp version 2 no wccp version 2 Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands (config) windows-domain (config) windows-domain To configure Windows domain server options on a WAAS device, use the windows-domain global configuration command. To disable this feature, use the no form of this command.
Chapter 3 CLI Commands (config) windows-domain Command Modes global configuration Device Modes application-accelerator central-manager Usage Guidelines Use this global configuration command to set the Windows domain server parameters for a WAAS device. When you enable Kerberos authentication, the default realm is DOMAIN.COM and the security is ADS. If you disable Kerberos authentication, the security is domain.
Chapter 3 CLI Commands (config) windows-domain show windows-domain windows-domain Cisco Wide Area Application Services Command Reference OL-21611-01 3-639
Chapter 3 CLI Commands Interface Configuration Mode Commands To set, view, and test the configuration of WAAS software features on a specific interface, use the interface global configuration command. interface {GigabitEthernet slot/port | InlineGroup slot/group | PortChannel 1 | Standby 1} Syntax Description GigabitEthernet slot/port Selects a gigabit ethernet interface to configure. InlineGroup slot/group Selects an inline group interface to configure.
Chapter 3 CLI Commands (config-if) autosense (config-if) autosense To enable autosense on an interface, use the autosense interface configuration command. To disable this function, use the no form of this command. autosense no autosense Syntax Description This command has no arguments or keywords. Defaults Autosense is enabled by default.
Chapter 3 CLI Commands (config-if) bandwidth (config-if) bandwidth To configure the link speed on a network interface, use the bandwidth interface configuration command. To restore default values, use the no form of this command. bandwidth {10 | 100 | 1000} no bandwidth {10 | 100 | 1000} Syntax Description 10 Sets the link speed to 10 megabits per second (Mbps). 100 Sets the link speed to 100 Mbps. 1000 Sets the link speed to 1000 Mbps.
Chapter 3 CLI Commands (config-if) bandwidth Examples The following example shows how to set an interface bandwidth to 1000 Mbps: WAE(config-if)# bandwidth 1000 The following example shows how to restore default bandwidth values on an interface: WAE(config-if)# no bandwidth Related Commands (config-if) autosense (config) interface GigabitEthernet Cisco Wide Area Application Services Command Reference OL-21611-01 3-643
Chapter 3 CLI Commands (config-if) cdp (config-if) cdp To enable the Cisco Discovery Protocol (CDP) on a particular interface on a WAAS device, rather than on all interfaces, use the cdp interface configuration command. cdp enable Syntax Description enable Defaults No default behavior or values. Command Modes interface configuration Device Modes application-accelerator Enables CDP on an interface.
Chapter 3 CLI Commands (config-if) cdp show startup-config Cisco Wide Area Application Services Command Reference OL-21611-01 3-645
Chapter 3 CLI Commands (config-if) encapsulation dot1Q (config-if) encapsulation dot1Q To set the VLAN ID that is to be assigned to traffic that leaves a WAE, use the encapsulation dot1Q interface configuration command. encapsulation dot1Q VLAN Syntax Description VLAN Defaults No default behavior or values. Command Modes interface configuration Device Modes application-accelerator Usage Guidelines The encapsulation dot1Q command is available only for the inlineGroup interface.
Chapter 3 CLI Commands (config-if) exit (config-if) exit To terminate interface configuration mode and return to the global configuration mode, use the exit command. exit Syntax Description This command has no arguments or keywords.
Chapter 3 CLI Commands (config-if) failover timeout (config-if) failover timeout To set the maximum time for the inline interface to transition traffic to another port after a failure event, use the failover timeout interface configuration command. To disable this function, use the no form of this command. failover timeout {1 | 3 | 5} no failover timeout {1 | 3 | 5} Syntax Description 1 Specifies the number of seconds to a failover. 3 Specifies the number of seconds to a failover.
Chapter 3 CLI Commands (config-if) full-duplex (config-if) full-duplex To configure an interface for full-duplex operation on a WAAS device, use the full-duplex interface configuration command. To disable this function, use the no form of this command. full-duplex no full-duplex Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands (config-if) full-duplex (config) interface GigabitEthernet show interface show running-config show startup-config Cisco Wide Area Application Services Command Reference 3-650 OL-21611-01
Chapter 3 CLI Commands (config-if) half-duplex (config-if) half-duplex To configure an interface for half-duplex operation on a WAAS device, use the half-duplex interface configuration command. To disable this function, use the no form of this command. half-duplex no half-duplex Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands (config-if) half-duplex (config) interface GigabitEthernet show interface show running-config show startup-config Cisco Wide Area Application Services Command Reference 3-652 OL-21611-01
Chapter 3 CLI Commands (config-if) inline (config-if) inline To enable inline interception for an inlineGroup interface, use the inline interface configuration command. To disable inline interception, use the no form of this command. inline [vlan {all | native | vlan_list}] no inline [vlan {all | native | vlan_list}] Syntax Description vlan (Optional) Modifies the VLAN list parameters. all Applies the command to all tagged and untagged packets. native Specifies untagged packets.
Chapter 3 CLI Commands (config-if) inline The following example shows how to disable inline interception on the same ports for 802.1Q-encapsulated packets that have the VLAN ID 5 or any VLAN ID between 10 and 15, inclusive. If the two VLANs are combined in the given order, inline interception is performed for all packets received on ports in group 0 of slot 1, except those packetson VLANs 5, 10, 11, 12, 13, 14, and 15.
Chapter 3 CLI Commands (config-if) ip (config-if) ip To configure the IP address or subnet mask, or to negotiate an IP address from DHCP on the interface of the WAAS device, use the ip interface configuration command. To disable this function, use the no form of this command.
Chapter 3 CLI Commands (config-if) ip Use the no form of the command to disable a specific IP address: WAE(config-if)# no ip address ip_address netmask Note No two interfaces can have IP addresses in the same subnet. Use the ip-address dhcp command to negotiate a reusable IP address from DHCP. Examples The following example shows how to configure the port-channel interface with an IP address of 10.10.10.10 and a netmask of 255.0.0.
Chapter 3 CLI Commands (config-if) ip access-group (config-if) ip access-group To control connections on a specific interface of a WAAS device by applying a predefined access list, use the ip access-group interface configuration command. To disable an access list, use the no form of this command.
Chapter 3 CLI Commands (config-if) mtu (config-if) mtu To set the interface Maximum Transmission Unit (MTU) packet size, use the mtu interface configuration command. To reset the MTU packet size, use the no form of this command. mtu mtusize no mtu mtusize Syntax Description mtusize Defaults No default behavior or values. Command Modes interface configuration Device Modes application-accelerator MTU packet size in bytes (88–1500).
Chapter 3 CLI Commands (config-if) shutdown (config-if) shutdown To shut down a specific hardware interface on a WAAS device, use the shutdown interface configuration command. To restore an interface to operation, use the no form of this command. shutdown no shutdown Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands (config-if) standby (config-if) standby To configure an interface on a WAAS device to be a backup for another interface, use the standby interface configuration command. To restore the default configuration of the interface, use the no form of this command. standby 1 [primary] no standby 1 [primary] Syntax Description 1 Configures standby group 1. primary (Optional) Defines the active interface in the standby group. By default, the first attached interface is active.
Chapter 3 CLI Commands (config-if) standby WAE(config)# interface gigabitEthernet 1/0 WAE(config-if)# standby 1 b. A second Gigabit Ethernet interface (slot 2/port 0) is added to Standby Group 1 and assigned as the primary (active) interface.
Chapter 3 CLI Commands Standard ACL Configuration Mode Commands To create and modify standard access lists on a WAAS device for controlling access to interfaces or applications, use the ip access-list standard global configuration command. To disable a standard access list, use the no form of this command. ip access-list standard {acl-name | acl-num} no ip access-list standard {acl-name | acl-num} Syntax Description standard Enables standard ACL configuration mode.
Chapter 3 CLI Commands Note IP ACLs that are defined on a router take precedence over the IP ACLs that are defined on the WAE. IP ACLs that are defined on a WAE take precedence over the WAAS application definition policies that are defined on the WAE. After creating an access list, you can include the access list in an access group using the access-group command, which determines how the access list is applied. You can also apply the access list to a specific application using the appropriate command.
Chapter 3 CLI Commands ip address 10.1.1.50 255.255.0.0 ip access-group teststdacl in exit . . . ip access-list standard teststdacl permit 192.168.1.0 any exit . . .
Chapter 3 CLI Commands (config-std-nacl) delete (config-std-nacl) delete To delete a line from the standard IP ACL, use the delete standard ACL configuration command. delete line-num Syntax Description line-num Entry at a specific line number in the access list. Defaults No default behavior or values.
Chapter 3 CLI Commands (config-std-nacl) deny (config-std-nacl) deny To add a line to a standard access-list that specifies the type of packets that you want the WAAS device to drop, use the deny standard ACL configuration command. To negate a standard IP ACL, use the no form of this command.
Chapter 3 CLI Commands (config-std-nacl) deny a 0 indicates a position that must be matched and a 1 indicates a position that does not matter. For instance, the wildcard 0.0.0.255 causes the last eight bits in the source IP address to be ignored. Therefore, the permit 192.168.1.0 0.0.0.255 entry allows access from any host on the 192.168.1.0 network. Examples The following example shows how to create a standard access list that denies any packets from source IP address 192.168.1.
Chapter 3 CLI Commands (config-std-nacl) exit (config-std-nacl) exit To terminate standard ACL configuration mode and return to the global configuration mode, use the exit command. exit Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands (config-std-nacl) list (config-std-nacl) list To display a list of specified entries within the standard IP ACL, use the list standard ACL configuration command. list [start-line-num [end-line-num]] Syntax Description start-line-num (Optional) Line number from which the list begins. end-line-num (Optional) Last line number in the list. Defaults No default behavior or values.
Chapter 3 CLI Commands (config-std-nacl) move (config-std-nacl) move To move a line to a new position within the standard IP ACL, use the move standard ACL configuration command. move old-line-num new-line-num Syntax Description old-line-num Line number of the entry to move. new-line-num New position of the entry. The existing entry is moved to the following position in the access list.
Chapter 3 CLI Commands (config-std-nacl) permit (config-std-nacl) permit To add a line to a standard access list that specifies the type of packets that you want the WAAS device to accept for further processing, use the permit standard ACL configuration command. To negate a standard IP ACL, use the no form of this command.
Chapter 3 CLI Commands (config-std-nacl) permit instance, the wildcard 0.0.0.255 causes the last eight bits in the source IP address to be ignored. Therefore, the permit 192.168.1.0 0.0.0.255 entry allows access from any host on the 192.168.1.0 network. Examples The following example shows how to create a standard access list that permits any packets from source IP address 192.168.1.0 for further processing: WAE(config)# ip access-list standard teststdacl WAE(config-std-nacl)# permit 192.168.1.
Chapter 3 CLI Commands Extended ACL Configuration Mode Commands To create and modify extended access lists on a WAAS device for controlling access to interfaces or applications, use the ip access-list extended global configuration command. To disable an extended access list, use the no form of this command. ip access-list extended {acl-name | acl-num} no ip access-list extended {acl-name | acl-num} Syntax Description extended Enables extended ACL configuration mode.
Chapter 3 Note CLI Commands ACLs that are defined on a router take precedence over the ACLs that are defined on the WAE. ACLs that are defined on a WAE take precedence over the WAAS application definition policies that are defined on the WAE. After creating an access list, you can include the access list in an access group using the access-group command, which determines how the access list is applied. You can also apply the access list to a specific application using the appropriate command.
Chapter 3 CLI Commands interface GigabitEthernet 1/0 ip address 10.1.1.50 255.255.0.0 ip access-group testextacl in exit . . . ip access-list extended testextacl permit tcp any any eq www permit tcp host 10.1.1.5 any eq ssh exit . . .
Chapter 3 CLI Commands (config-ext-nacl) delete (config-ext-nacl) delete To delete a line from the extended ACL, use the delete extended ACL configuration command. delete line-num Syntax Description line-num Entry at a specific line number in the access list. Defaults No default behavior or values.
Chapter 3 CLI Commands (config-ext-nacl) deny (config-ext-nacl) deny To add a line to an extended access list that specifies the type of packets that you want the WAAS device to drop, use the deny extended ACL configuration command. To add a condition to the extended ACL, note that the options depend on the chosen protocol.
Chapter 3 CLI Commands (config-ext-nacl) deny wildcard (Optional) Wildcard. The notation is in 4-digit, dotted-decimal format. Tge bits to match are identified by a digital value of 0; the bits to ignore are identified by a 1. For extended IP ACLs, the wildcard parameter of the ip access-list command is always optional. If the host keyword is specified for a extended IP ACL, then the wildcard parameter is not allowed. host source-ip Specifies to match the following IP address.
Chapter 3 CLI Commands (config-ext-nacl) deny a 0 indicates a position that must be matched and a 1 indicates a position that does not matter. For instance, the wildcard 0.0.0.255 causes the last eight bits in the source IP address to be ignored. The permit 192.168.1.0 0.0.0.255 entry allows access from any host on the 192.168.1.0 network. For extended IP ACLs, the wildcard parameter is required if the host keyword is not specified.
Chapter 3 CLI Commands (config-ext-nacl) deny Table 3-2 TCP Keywords for Extended Access Lists (continued) CLI TCP Keyword Description TCP Port Number tacacs Terminal Access Controller Access Control System 49 telnet Telnet 23 www World Wide Web (HTTP) 80 Table 3-3 lists the keywords that you can use to match specific ICMP message types and codes.
Chapter 3 CLI Commands (config-ext-nacl) deny interface GigabitEthernet 1/0 ip address 10.1.1.50 255.255.0.0 ip access-group extended testextacl in exit . . . ip access-list extended testextacl permit tcp any any eq www permit tcp host 10.1.1.5 any eq ssh exit . . .
Chapter 3 CLI Commands (config-ext-nacl) exit (config-ext-nacl) exit To terminate extended ACL configuration mode and return to the global configuration mode, use the exit command. exit Syntax Description This command has no arguments or keywords.
Chapter 3 CLI Commands (config-ext-nacl) list (config-ext-nacl) list To display a list of specified entries within the extended ACL, use the list extended ACL configuration command. list [start-line-num [end-line-num]] Syntax Description start-line-num (Optional) Line number from which the list begins. end-line-num (Optional) Last line number in the list. Defaults No default behavior or values.
Chapter 3 CLI Commands (config-ext-nacl) move (config-ext-nacl) move To move a line to a new position within the extended ACL, use the move extended ACL configuration command. move old-line-num new-line-num Syntax Description old-line-num Line number of the entry to move. new-line-num New position of the entry. The existing entry is moved to the following position in the access list. Defaults No default behavior or values.
Chapter 3 CLI Commands (config-ext-nacl) permit (config-ext-nacl) permit To add a line to an extended access list that specifies the type of packets that you want the WAAS device to accept for further processing, use the permit extended ACL configuration command. To add a condition to the extended ACL, note that the options depend on the chosen protocol.
Chapter 3 CLI Commands (config-ext-nacl) permit wildcard (Optional) Wildcard. The notation is in 4-digit, dotted-decimal format. Tge bits to match are identified by a digital value of 0; the bits to ignore are identified by a 1. For extended IP ACLs, the wildcard parameter of the ip access-list command is always optional. If the host keyword is specified for a extended IP ACL, then the wildcard parameter is not allowed. host source-ip Specifies to match the following IP address.
Chapter 3 CLI Commands (config-ext-nacl) permit a 0 indicates a position that must be matched and a 1 indicates a position that does not matter. For instance, the wildcard 0.0.0.255 causes the last eight bits in the source IP address to be ignored. The permit 192.168.1.0 0.0.0.255 entry allows access from any host on the 192.168.1.0 network. For extended IP ACLs, the wildcard parameter is required if the host keyword is not specified.
Chapter 3 CLI Commands (config-ext-nacl) permit Table 3-5 TCP Keywords for Extended Access Lists (continued) CLI TCP Keyword Description TCP Port Number tacacs Terminal Access Controller Access Control System 49 telnet Telnet 23 www World Wide Web (HTTP) 80 Table 3-6 lists the keywords that you can use to match specific ICMP message types and codes.
Chapter 3 CLI Commands (config-ext-nacl) permit interface GigabitEthernet 1/0 ip address 10.1.1.50 255.255.0.0 ip access-group testextacl in exit . . . ip access-list extended testextacl permit tcp any any eq www permit tcp host 10.1.1.5 any eq ssh exit . . .
Chapter 3 CLI Commands (config-ext-nacl) permit Cisco Wide Area Application Services Command Reference 3-690 OL-21611-01
Chapter 3 CLI Commands Preposition Configuration Mode Commands To create and modify preposition directives on a WAAS device for prepositioning files for WAFS, use the accelerator cifs preposition global configuration command. accelerator cifs preposition directive_id Syntax Description directive_id Defaults No default behavior or values.
Chapter 3 WAE(config-preposition)# WAE(config-preposition)# WAE(config-preposition)# WAE(config-preposition)# WAE(config-preposition)# WAE(config-preposition)# WAE(config-preposition)# WAE(config-preposition)# WAE(config-preposition)# WAE(config-preposition)# Related Commands CLI Commands dscp 45 duration 30 min-file-size 0 name "Program Files" root Program_Files scan-type full server 10.1.221.
Chapter 3 CLI Commands (config-preposition) credentials (config-preposition) credentials To set the username and password credentials for a file server in a preposition directive, use the credentials preposition configuration command. credentials username username password {0 | 1} password} Syntax Description username username Specifies the username. password {0 | 1} password Specifies the password. To indicate that the password string is unencrypted, specify 0.
Chapter 3 CLI Commands (config-preposition) dscp (config-preposition) dscp To set the DSCP marking value for a preposition task, use the dscp preposition configuration command. To remove a DSCP marking value, use the no form of this command. dscp value no dscp value Syntax Description value Defaults No default behavior or values.
Chapter 3 CLI Commands (config-preposition) duration (config-preposition) duration To set the maximum duration for a preposition task, use the duration preposition configuration command. To remove a duration limit, use the no form of this command. duration minutes no duration minutes Syntax Description minutes Defaults No default behavior or values.
Chapter 3 CLI Commands (config-preposition) enable (config-preposition) enable To enable a preposition directive, use the enable preposition configuration command. To disable a preposition directive, use the no form of this command. enable no enable Syntax Description This command has no arguments or keywords. Defaults Not enabled.
Chapter 3 CLI Commands (config-preposition) ignore-hidden-dir (config-preposition) ignore-hidden-dir To ignore hidden directories in the set of files to be prepositioned, use the ignore-hidden-dir preposition configuration command. ignore-hidden-dir Syntax Description This command has no arguments or keywords. Defaults Hidden directories are not ignored.
Chapter 3 CLI Commands (config-preposition) max-cache (config-preposition) max-cache To set the maximum percentage of the cache that the files from a preposition directive can use, use the max-cache preposition configuration command.
Chapter 3 CLI Commands (config-preposition) max-file-size (config-preposition) max-file-size To set the maximum size file that can be prepositioned, use the max-file-size preposition configuration command. To remove this limit, use the no form of this command. max-file-size size_in_kb no max-file-size size_in_kb Syntax Description size_in_kb Defaults No default behavior or values.
Chapter 3 CLI Commands (config-preposition) min-file-size (config-preposition) min-file-size To set the minimum size file that can be prepositioned, use the min-file-size preposition configuration command. To remove this limit, use the no form of this command.
Chapter 3 CLI Commands (config-preposition) name (config-preposition) name To set the display name of a preposition directive, use the name preposition configuration command. name name Syntax Description name Defaults The default name is New preposition directive n. Command Modes preposition configuration mode Device Modes application-accelerator Examples The following example shows how to set the preposition directive name: Name of a preposition directive.
Chapter 3 CLI Commands (config-preposition) pattern (config-preposition) pattern To filter the files included for a preposition directive, use the pattern preposition configuration command. To remove this filter, use the no form of this command. pattern {equals | starts-with | ends-with | contains} text no pattern {equals | starts-with | ends-with | contains} text Syntax Description equals Specifies to limit the selected files to those filenames that are equal to the specified text.
Chapter 3 CLI Commands (config-preposition) recursive (config-preposition) recursive To include files in subdirectories for a preposition directive, use the recursive preposition configuration command. To not include subdirectories, use the no form of this command. recursive no recursive Syntax Description This command has no arguments or keywords. Defaults Subdirectories are included.
Chapter 3 CLI Commands (config-preposition) root (config-preposition) root To set a root directory for a preposition directive, use the root preposition configuration command. root path Syntax Description path Full pathname to the directory, not including the server name. Defaults No default behavior or values.
Chapter 3 CLI Commands (config-preposition) scan-type (config-preposition) scan-type To set the file scanning type for a preposition directive, use the scan-type preposition configuration command. scan-type {full | since last | since period units} Syntax Description full Specifies to copy all files to the Edge WAE cache. since last Specifies to copy only the files that have changed since the last preposition to the Edge WAE cache.
Chapter 3 CLI Commands (config-preposition) schedule (config-preposition) schedule To set the schedule for starting a preposition task, use the schedule preposition configuration command. schedule {now | daily time | date date time | weekly {dayname [dayname]...} time time | monthly {week-day dayname weeknumber time time | {day day [day]...} } time time} Syntax Description now Specifies that prepositioning occurs within a few minutes of submitting the schedule.
Chapter 3 CLI Commands (config-preposition) schedule The following example shows how to set the preposition task to run on December 15, 2008 at midnight: WAE(config-preposition)# schedule date 15:12:2008 00:00 The following example shows how to set the preposition task to run weekly on Wednesdays and Fridays at 8 p.m.: WAE(config-preposition)# schedule weekly Wednesday Friday time 20:00 The following example shows how to set the preposition task to run monthly on the 1st and 15th days at 1:00 a.m.
Chapter 3 CLI Commands (config-preposition) server (config-preposition) server To set a server name for a preposition directive, use the server preposition configuration command. server name Syntax Description name Server name. Defaults No default behavior or values.
Chapter 3 CLI Commands Virtual Blade Configuration Mode Commands To configure virtual blades on a WAE device, use the virtual-blade global configuration command. To disable a virtual blade, use the no form of this command. virtual-blade [virtual-blade-number] no virtual-blade [virtual-blade-number] Syntax Description virtual-blade-number Defaults No default behavior or values.
Chapter 3 CLI Commands (config-vb) cpu-list (config-vb) description (config-vb) device (config-vb) disk (config-vb) interface (config-vb) memory (config-vb) vnc Cisco Wide Area Application Services Command Reference 3-710 OL-21611-01
Chapter 3 CLI Commands (config-vb) autostart (config-vb) autostart To set a virtual blade to automatically start when the WAE is started, use the autostart virtual blade configuration command. To prevent a virtual blade from starting automatically, use the no form of this command. autostart no autostart Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands (config-vb) boot (config-vb) boot To configure the boot image location and source for a virtual blade, use the boot virtual blade configuration command. boot {cd-image {cd-rom | disk location} | fd-image disk location | from {cd-rom | disk | network}} Syntax Description cd-image Specifies the location of the boot CD image for the virtual blade. This image can be located on a CD in the WAE CD-ROM drive or it can be an ISO file located on the WAE hard drive.
Chapter 3 CLI Commands (config-vb) boot Use the boot from cd-rom option before you have installed a guest OS, to boot from a guest OS installer CD (a physical CD or an .iso file located in /local1/vbs). Use the boot from disk option after you have installed a guest OS, to boot from the installed guest OS. If you specified boot from disk, the cd-image keyword is optional and configures the location of a CD-ROM image that is made available to the guest OS (but is not used for booting).
Chapter 3 CLI Commands (config-vb) cpu-list (config-vb) cpu-list To configure the CPU assignments that the virtual blade runs on, use the cpu-list virtual blade configuration command. To remove the virtual blade CPU list configuration, use the no form of this command. cpu-list cpu1 [cpu2] no cpu-list cpu1 [cpu2] Syntax Description cpu-list cpu1 [cpu2] Specifies the CPUs that are available for this virtual blade. The virtual blade may run on a single CPU or both, if available.
Chapter 3 CLI Commands (config-vb) cpu-list (config-vb) device (config-vb) disk (config-vb) interface (config-vb) memory Cisco Wide Area Application Services Command Reference OL-21611-01 3-715
Chapter 3 CLI Commands (config-vb) description (config-vb) description To enter a description for a virtual blade on your WAE, use the description virtual blade configuration command. description description-text Syntax Description description-text Text to briefly describe the virtual blade. Defaults No default behavior or values.
Chapter 3 CLI Commands (config-vb) device (config-vb) device To set the device emulation parameters used by the virtual blade on your WAE, use the device virtual blade configuration command. device {cpu {qemu64 | qemu32} | nic {rtl8139 | E1000 | virtio} | disk {IDE | virtio} | keyboard {emulation}} Syntax Description Defaults cpu Specifies the CPU emulation to be used on the virtual blade. qemu64 Specifies a 64-bit processor emulator.
Chapter 3 CLI Commands (config-vb) device Table 3-1 Examples Keyboard Device Emulation Values (continued) Emulation Value German (Swiss) de-ch English (UK) en-gb English (US) (default) en-us Spanish es Estonian et Finnish fi Faroese fo French fr French (Belgium) fr-be French (Canada) fr-ca French (Switzerland) fr-ch Croatian hr Hungarian hu Icelandic is Italian it Japanese ja Lithuanian lt Latvian lv Macedonian mk Dutch nl Dutch (Belgium) nl-be Norwegian no
Chapter 3 CLI Commands (config-vb) device Related Commands (config-vb) autostart (config-vb) boot (config-vb) cpu-list (config-vb) description (config-vb) disk (config-vb) interface (config-vb) memory Cisco Wide Area Application Services Command Reference OL-21611-01 3-719
Chapter 3 CLI Commands (config-vb) disk (config-vb) disk To allocate disk space for a virtual blade on the WAE hard drive, use the disk virtual blade configuration command. disk disk1-size disk2-size disk3-size disk4-size Syntax Description disk1-size Amount of disk space allocated for the virtual disk 1 of the virtual blade in gigabytes. The range of valid values is from 1 to 1000. disk2-size Amount of disk space allocated for the virtual disk 2 of the virtual blade in gigabytes.
Chapter 3 CLI Commands (config-vb) disk (config-vb) device (config-vb) interface (config-vb) memory Cisco Wide Area Application Services Command Reference OL-21611-01 3-721
Chapter 3 CLI Commands (config-vb) interface (config-vb) interface To bridge a virtual blade interface to an interface on your WAE, use the interface virtual blade configuration command. interface vb-interface bridge {GigabitEthernet [slot]/[port] | PortChannel channel} Syntax Description vb-interface Virtual blade interface to be bridged; valid values are 1 or 2. bridge Specifies that a virtual blade interface will be bridged to a physical WAE interface.
Chapter 3 CLI Commands (config-vb) memory (config-vb) memory To allocate memory for a virtual blade from the WAE system, use the memory virtual blade configuration command. memory memory-allocation Syntax Description memory-allocation Defaults No default behavior or values.
Chapter 3 CLI Commands (config-vb) vnc (config-vb) vnc To enable the VNC server for a virtual blade, use the vnc virtual blade configuration command. To disable the VNC server for a virtual blade, use the no form of this command. vnc no vnc Syntax Description This command has no arguments or keywords. Defaults The VNC server is enabled by default. Command Modes virtual blade configuration mode Device Modes application-accelerator Usage Guidelines The VNC server is enabled by default.
Chapter 3 CLI Commands PKI Certificate Authority Configuration Mode Commands To configure public key infrastructure (PKI) encryption certificate authorities on a WAAS device, use the crypto pki ca global configuration command. To delete a PKI encryption certificate authority, use the no form of the command. crypto pki ca certificate_authority_name no crypto pki ca certificate_authority_name Syntax Description certificate_authority_name Defaults No default behavior or values.
Chapter 3 CLI Commands (config-ca) description (config-ca) revocation-check Cisco Wide Area Application Services Command Reference 3-726 OL-21611-01
Chapter 3 CLI Commands (config-ca) ca-certificate (config-ca) ca-certificate To set the certification authority file to be used by the WAAS device, use the ca-certificate certification authority configuration command. ca-certificate filename.ca Syntax Description filename.ca Defaults No default behavior or values. Command Modes certification authority configuration Device Modes application-accelerator The filename of the certificate authority. The filename must end in .
Chapter 3 CLI Commands (config-ca) description (config-ca) description To enter a description for the certification authority to be used by the WAAS device, use the description command. description description-text Syntax Description description-text Defaults No default behavior or values. Command Modes certification authority configuration Device Modes application-accelerator Test to briefly describe the certification authority being used.
Chapter 3 CLI Commands (config-ca) revocation-check (config-ca) revocation-check To configure the certification authority revocation checking method, use the revocation-check command. revocation-check {none | ocsp-cert-url | ocsp-url} [none | ocsp-cert-url | ocsp-url] Syntax Description none No revocation checking is used. ocsp-cert-url Enables Online Certificate Status Protocol (OCSP) revocation status checking using the CA server URL defined in the CA certificate.
Chapter 3 CLI Commands (config-ca) revocation-check Cisco Wide Area Application Services Command Reference 3-730 OL-21611-01
Chapter 3 CLI Commands PKI Global Settings Configuration Mode Commands To configure public key infrastructure (PKI) encryption global settings on a WAAS device, use the crypto pki global-settings global configuration command. crypto pki global-settings Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands (config-pki-global-settings) ocsp (config-pki-global-settings) ocsp To enter the URL to be used as the global settings for the Online Certificate Status Protocol (OCSP) protocol revocation status checking, use the ocsp PKI global settings configurations mode command. ocsp url http://address Syntax Description url http://address Defaults No default behavior or values.
Chapter 3 CLI Commands (config-pki-global-settings) revocation-check (config-pki-global-settings) revocation-check To configure the global settings revocation checking method, use the revocation-check command. revocation-check {ocsp-cert-url | ocsp-url} [none] Syntax Description ocsp-cert-url Enables Online Certificate Status Protocol (OCSP) revocation status checking using the CA server URL defined in the CA certificate.
Chapter 3 CLI Commands (config-pki-global-settings) revocation-check Cisco Wide Area Application Services Command Reference 3-734 OL-21611-01
Chapter 3 CLI Commands SSL Accelerated Service Configuration Mode Commands SSL accelerated services lets you enable and configure SSL acceleration on your WAAS system, and define services to be accelerated on the SSL path. To configure secure socket layer (SSL) encryption accelerated services on a WAAS device, use the crypto ssl services accelerated-service global configuration command. To delete a parameter use the no form of the command.
Chapter 3 Related Commands CLI Commands (config-ssl-accelerated) cipher-list (config-ssl-accelerated) client-cert-verify (config-ssl-accelerated) client-version-rollback-check (config-ssl-accelerated) description (config-ssl-accelerated) inservice (config-ssl-accelerated) server-cert-key (config-ssl-accelerated) server-cert-verify (config-ssl-accelerated) server-domain (config-ssl-accelerated) server-ip (config-ssl-accelerated) server-name (config-ssl-accelerated) version Cisco Wide Area Application Ser
Chapter 3 CLI Commands (config-ssl-accelerated) cipher-list (config-ssl-accelerated) cipher-list To configure secure socket layer (SSL) encryption cipher lists on a WAAS device, use the cipher-list command. To delete a cipher list use the no form of the command. cipher-list cipher-list-name no cipher-list cipher-list-name Syntax Description cipher-list-name Defaults No default behavior or values.
Chapter 3 CLI Commands (config-ssl-accelerated) client-cert-verify (config-ssl-accelerated) client-cert-verify To enable verification of client certificates, use the client-cert-verify command. client-cert-verify [revocation-check none] Syntax Description revocation-check none Defaults No default behavior or values. Command Modes SSL accelerated service configuration Device Modes application-accelerator Specifies a revocation check null method that returns revocation success.
Chapter 3 CLI Commands (config-ssl-accelerated) client-version-rollback-check (config-ssl-accelerated) client-version-rollback-check To disable the client SSL version rollback check, use the client-version-rollback-check command. client-version-rollback-check disable Syntax Description disable Defaults No default behavior or values. Command Modes SSL accelerated service configuration Device Modes application-accelerator Disables the client SSL version rollback check.
Chapter 3 CLI Commands (config-ssl-accelerated) description (config-ssl-accelerated) description To add a description of the SSL accelerated service, use the description command. description description Syntax Description description Defaults No default behavior or values. Command Modes SSL accelerated service configuration Device Modes application-accelerator Configures a string that is the description of the SSL accelerated service.
Chapter 3 CLI Commands (config-ssl-accelerated) inservice (config-ssl-accelerated) inservice To enable the accelerated service, use the inservice command. inservice Syntax Description This command has no arguments or keywords. Defaults No default behavior or values.
Chapter 3 CLI Commands (config-ssl-accelerated) server-cert-key (config-ssl-accelerated) server-cert-key To configure a certificate and private key, use the server-cert-key command. server-cert-key filename Syntax Description filename Filename of the certificate and key. Must be in PKCS#12 and have a “.p12” extension. Defaults No default behavior or values.
Chapter 3 CLI Commands (config-ssl-accelerated) server-cert-verify (config-ssl-accelerated) server-cert-verify To enable verification of server certificates, use the server-cert-verify command. server-cert-verify [revocation-check none] Syntax Description revocation-check none Defaults No default behavior or values. Command Modes SSL accelerated service configuration Device Modes application-accelerator Specifies a revocation check null method that returns revocation success.
Chapter 3 CLI Commands (config-ssl-accelerated) server-domain (config-ssl-accelerated) server-domain To configure the accelerated server domain and TCP port, use the server-domain command. server-domain srv-domain {port port-no} Syntax Description server-domain srv-domain Specifies the domain name of the accelerated server starting with the characters “*.”. 255 alphanumeric characters maximum, 63 characters per label/segment. port port-no Specifies the port number of the accelerated server.
Chapter 3 CLI Commands (config-ssl-accelerated) server-ip (config-ssl-accelerated) server-ip To configure the accelerated server IP address and TCP port, use the server-ip command. server-ip ip-address {port port-no} Syntax Description server-ip ip-address Specifies the IP address of the accelerated server. port port-no Specifies the port number of the accelerated server. Range is 1 to 65535. Defaults No default behavior or values.
Chapter 3 CLI Commands (config-ssl-accelerated) server-name (config-ssl-accelerated) server-name To configure the accelerated server hostname and TCP port, use the server-name command. server-name hostname {port port-no} Syntax Description server-name hostname Specifies the hostname of the accelerated server. 255 alphanumeric characters max, 63 characters per label/segment. port port-no Specifies the port number of the accelerated server. Range is 1 to 65535.
Chapter 3 CLI Commands (config-ssl-accelerated) version (config-ssl-accelerated) version To specify the type of SSL protocol to use for accelerated services, use the version command. version {all | ssl3 | tls1} Syntax Description version {all | ssl3 | tls1} Defaults No default behavior or values.
Chapter 3 CLI Commands (config-ssl-accelerated) version Cisco Wide Area Application Services Command Reference 3-748 OL-21611-01
Chapter 3 CLI Commands SSL Cipher List Configuration Mode Commands A cipher list is customer list of cipher suites that you assign to an SSL connection. To configure secure socket layer (SSL) encryption cipher lists on a WAAS device, use the crypto ssl cipher-list global configuration command. To delete a cipher list use the no form of the command.
Chapter 3 CLI Commands (config-cipher-list) cipher (config-cipher-list) cipher To add a cipher suite to a cipher list, or to change the priority of a cipher suite on the list, use the cipher command. cipher cipher-suite-name [priority value] Syntax Description cipher-suite-name The name of the cipher suite you want to add or reprioritize.
Chapter 3 CLI Commands (config-cipher-list) cipher Note Note Exportable cipher suites are those cipher suites that are considered not to be as strong as some of the other cipher suites (for example, 3DES or RC4 with 128-bit encryption) as defined by U.S. export restrictions on software products. Exportable cipher suites may be exported to most countries from the United States, and provide the strongest encryption available for exportable products.
Chapter 3 CLI Commands (config-cipher-list) cipher WAE(config-cipher-list)# cipher rsa-with-3des-ede-cbc-sha priority 1 Related Commands (config) crypto ssl Cisco Wide Area Application Services Command Reference 3-752 OL-21611-01
Chapter 3 CLI Commands SSL Global Service Configuration Mode Commands SSL global service lets you enable and configure basic SSL acceleration settings on your WAAS system. To configure global services on a WAAS device, use the crypto ssl services global-settings global configuration command. To delete a parameter use the no form of the command. crypto ssl services global-settings no crypto ssl services global-settings Syntax Description This command has no arguments or keywords.
Chapter 3 CLI Commands (config-ssl-global) version Cisco Wide Area Application Services Command Reference 3-754 OL-21611-01
Chapter 3 CLI Commands (config-ssl-global) cipher-list (config-ssl-global) cipher-list To configure secure socket layer (SSL) encryption cipher lists on a WAAS device, use the cipher-list command. To delete a cipher list use the no form of the command. cipher-list cipher-list-name no cipher-list cipher-list-name Syntax Description cipher-list-name Defaults No default behavior or values.
Chapter 3 CLI Commands (config-ssl-global) machine-cert-key (config-ssl-global) machine-cert-key To configure a certificate and private key, use the machine-cert-key command. machine-cert-key filename Syntax Description filename Defaults No default behavior or values. Command Modes SSL global service configuration Device Modes application-accelerator Filename of the certificate and key. Must be in PKCS#12 and have a “.p12” extension.
Chapter 3 CLI Commands (config-ssl-global) version (config-ssl-global) version To specify the type of SSL protocol to use for global services, use the version command. version {all | ssl3 | tls1} Syntax Description version {all | ssl3 | tls1} Defaults No default behavior or values.
Chapter 3 CLI Commands (config-ssl-global) version Cisco Wide Area Application Services Command Reference 3-758 OL-21611-01
Chapter 3 CLI Commands SSL Host Peering Service Configuration Mode Commands SSL peering service configuration parameters control secure communications established by the SSL accelerator between WAE devices while optimizing SSL connections. To configure secure socket layer (SSL) encryption peering services on a WAAS device, use the crypto ssl services host-service global configuration command. To delete a parameter use the no form of the command.
Chapter 3 CLI Commands (config-ssl-peering) version Cisco Wide Area Application Services Command Reference 3-760 OL-21611-01
Chapter 3 CLI Commands (config-ssl-peering) cipher-list (config-ssl-peering) cipher-list To configure secure socket layer (SSL) encryption cipher lists on a WAAS device, use the cipher-list command. To delete a cipher list use the no form of the command. cipher-list cipher-list-name no cipher-list cipher-list-name Syntax Description cipher-list-name Defaults No default behavior or values.
Chapter 3 CLI Commands (config-ssl-peering) peer-cert-verify (config-ssl-peering) peer-cert-verify To enable verification of peer certificates, use the peer-cert-verify command. peer-cert-verify [revocation-check none] Syntax Description revocation-check none Defaults No default behavior or values. Command Modes SSL host peering service configuration Device Modes application-accelerator Specifies a revocation check null method that returns revocation success.
Chapter 3 CLI Commands (config-ssl-peering) version (config-ssl-peering) version To specify the type of SSL protocol to use for management services, use the version command. version {all | ssl3 | tls1} Syntax Description version {all | ssl3 | tls1} Defaults No default behavior or values.
Chapter 3 CLI Commands (config-ssl-peering) version Cisco Wide Area Application Services Command Reference 3-764 OL-21611-01
Chapter 3 CLI Commands SSL Management Service Configuration Mode Commands SSL management services lets you configure SSL parameters used for secure communications between the Central Manager and the WAE devices. To configure secure socket layer (SSL) encryption management service parameters on a WAAS device, use the crypto ssl management-service global configuration command. To delete a parameter use the no form of the command.
Chapter 3 CLI Commands (config-ssl-mgmt) version Cisco Wide Area Application Services Command Reference 3-766 OL-21611-01
Chapter 3 CLI Commands (config-ssl-mgmt) cipher-list (config-ssl-mgmt) cipher-list To configure secure socket layer (SSL) encryption cipher lists on a WAAS device, use the cipher-list command. To delete a cipher list use the no form of the command. cipher-list cipher-list-name no cipher-list cipher-list-name Syntax Description cipher-list-name Defaults No default behavior or values.
Chapter 3 CLI Commands (config-ssl-mgmt) peer-cert-verify (config-ssl-mgmt) peer-cert-verify To enable verification of peer certificates, use the peer-cert-verify command. peer-cert-verify [revocation-check none] Syntax Description revocation-check none Defaults No default behavior or values. Command Modes SSL management service configuration Device Modes application-accelerator Specifies a revocation check null method that returns revocation success.
Chapter 3 CLI Commands (config-ssl-mgmt) version (config-ssl-mgmt) version To specify the type of SSL protocol to use for management services, use the version command. version {all | ssl3 | tls1} Syntax Description version {all | ssl3 | tls1} Defaults No default behavior or values.
Chapter 3 CLI Commands (config-ssl-mgmt) version Cisco Wide Area Application Services Command Reference 3-770 OL-21611-01
A P P E N D I X A Acronyms and Abbreviations Table A-1 defines the acronyms and abbreviations that are used in this publication.
Appendix A Table A-1 Acronyms and Abbreviations List of Acronyms and Abbreviations (continued) Acronym Expansion KDC key distribution center LDAP Lightweight Directory Access Protocol MAC Media Access Control Mbps megabits per second MD5 Message Digest 5 MIB Management Information Base MSRPC Microsoft Remote Procedure Call MTU maximum transmission unit NAS network access server/network attached storage NetBIOS Network Basic Input/Output System NMS Network Management system NTP N
Appendix A Acronyms and Abbreviations Table A-1 List of Acronyms and Abbreviations (continued) Acronym Expansion TDB Trivial DataBase TFTP Trivial File Transfer Protocol ToS type of service UDI unique device identifier UDP User Datagram Protocol UPS uninterruptible power supply USB Universal Serial Bus UTC Coordinated Universal Time UUCP Unix-to-Unix Copy Program VID version ID WAE Wide Area Application Engine WAAS Wide Area Application Services WAFSFS Wide Area File Services
Appendix A Acronyms and Abbreviations Cisco Wide Area Application Services Command Reference A-4 OL-21611-01
CLI COMMAND SUMMARY BY MODE Configuration Mode Commands (config) disk error-handling 3-500 (config) disk logical shutdown (config) aaa accounting 3-433 (config) disk object-cache extend (config) aaa authorization commands (config) accelerator cifs 3-436 3-437 (config) egress-method (config) end (config) accelerator cifs preposition 3-439 (config) exit (config) accelerator http 3-442 (config) flow monitor (config) help (config) hostname (config) accelerator ssl 3-447 (config) inetd (conf
Command Summary by Mode (config) policy-engine application map basic 3-555 (config) policy-engine application map other optimize DRE 3-558 (config) policy-engine application map other optimize full 3-560 (config) policy-engine config (config) port-channel 3-564 3-566 (config) username 3-623 3-629 (config) wccp shutdown 3-631 3-633 (config) wccp tcp-promiscuous router-list-num 3-569 (config) radius-server 3-573 (config) windows-domain 3-634 3-636 3-637 3-575 (config) snmp-server access-li
Command Summary by Mode copy ftp debug translog 3-36 copy http 3-39 copy running-config 3-42 copy startup-config copy sysreport 3-44 3-45 copy system-status 3-47 copy tech-support copy tftp cpfile debug wafs 3-117 debug wccp 3-119 delfile 3-121 deltree 3-122 dir 3-123 disable 3-48 disk 3-50 3-126 crypto delete 3-53 enable crypto export 3-54 exit crypto generate crypto import crypto pki 3-130 3-131 help 3-58 3-61 3-65 less debug authentication 3-71 3-135 3-137 li
Command Summary by Mode show bypass show snmp 3-173 show cache http-metadatacache 3-174 show ssh 3-248 3-254 show cdp 3-176 show startup-config show cifs 3-182 show statistics accelerator show clock show statistics aoim 3-184 show cms show cms secure-store show debugging show statistics cifs 3-192 3-300 show statistics connection closed 3-196 show egress-methods show statistics connection optimized 3-205 show statistics crypto ssl ciphers show hosts 3-211 show statistics datamo
Command Summary by Mode show synq list show sysfs volumes show tacacs show tcp (config-ext-nacl) list 3-371 (config-ext-nacl) permit 3-377 3-381 show transaction-logging show user 3-382 show version (config-if) half-duplex 3-651 3-653 3-655 3-657 3-658 (config-if) shutdown 3-410 (config-if) standby 3-659 3-660 3-414 3-416 traceroute PKI Certificate Authority Configuration Mode Commands 3-418 transaction-log 3-419 (config-ca) ca-certificate 3-420 (config-ca) description 3-421 vi
Command Summary by Mode (config-preposition) dscp (config-ssl-global) machine-cert-key 3-694 (config-preposition) duration (config-ssl-global) version 3-695 (config-preposition) enable (config-preposition) max-cache 3-697 3-698 (config-preposition) max-file-size 3-699 (config-preposition) min-file-size 3-700 SSL Host Peering Service Configuration Mode Commands (config-ssl-peering) cipher-list 3-761 (config-ssl-peering) peer-cert-verify 3-701 (config-preposition) recursive (config-preposit
