Installation guide
Table Of Contents
- CiscouBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation an...
- If You Need More Information
- Wireless Modem Card and Subsystem Overview
- Field-Replaceable Units
- Installation Prerequisites
- Removing and Installing the Wireless Modem Card
- Installing the Power Feed Panel
- Configuring a Wireless Modem Card
- Command Reference
- Syntax Conventions
- Startup Commands
- Installation and Configuration Commands
- Operating Commands
- Monitoring the System
- Troubleshooting
- show controllers radio
- radio histogram
- radio byteErrorHist
- show interfaces radio (histspec)
- show interfaces radio (histdata)
- debug radio
- Images and Image Repositories
- radio image-add
- radio image-move
- show interfaces radio (imagehdr)
- show radio repository
- radio snapshot
- radio scope-output
- radio timeline
- show interfaces radio (tlspec)
- show interfaces radio (tldata)
- Regulatory Compliance and Safety Information
- FCC Registration and Requirements
- Translated Safety Warnings
- Short-Circuit Protection Warning
- Disconnect Device Warning
- Lightning Activity Warning
- Installation Warning
- Jewelry Removal Warning
- Supply Circuit Warning
- Service Personnel Warning
- Product Disposal Warning
- Faceplates and Cover Panel Requirement
- Chassis—Rack-Mounting and Servicing Warning
- Restricted Area Warning
- Earthed Conductor Warning
- Power Cabling Warning
- Ground Connection Warning
- Power Supply Wiring Warning
- Copper Conductors Warning
- Exposed DC Power Wire Warning
- 48 VDC Power System Warning
- SELV-IEC 60950 DC Power Supply Warning
- DC Power Disconnection Warning
- DC Input Wiring Warning
- Ground Wire Connection Warning
- Ground Conductor Warning
- No. 26 AWG Wire Warning
- Coaxial Cable Specification Warning
- Transverter Location Warning
- Obtaining Documentation
- Obtaining Technical Assistance
98
Cisco uBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation and Configuration
78-6030-03
Command Reference
show interfaces radio (tldata)
Use this command in privileged EXEC mode to display the timeline data collected for the identified
specifications.
show interfaces radio slot/port tldata [statParam antenna_num [dsp dspId]]
Syntax Description
Refer to radio timeline for syntax descriptions.
Example
The following example will display the timeline inr data for the modem card installed in slot 3, port 0
of the Cisco uBR7200 series router:
UBR04# show interfaces radio 3/0 tldata inr
Number of Points Captured=100 Trigger Location=54
0 :0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
10 :0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
20 :0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
30 :0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
40 :0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
50 :FFFFFFFF FFFFFFFF 0000 0000 0000 0000 0000 0001 FFFFFFFF FFFFFFFF
60 :0000 0002 FFFFFFFF FFFFFFFF 0000 0001 0000 0000 0000 0000
70 :0000 0000 0000 0001 FFFFFFFF FFFFFFFF 0000 0000 0000 0001
80 :FFFFFFFF FFFFFFFF FFFFFFFF FFFFFFFF 0000 0002 FFFFFFFF FFFFFFFF 0000 0002
90 :FFFFFFFF FFFFFFFF 0000 0000 0000 0001 FFFFFFFF FFFFFFFF 0000 0000
Reading the Data
Some data returned by the DSPs can be more useful if you convert it to more meaningful values. Table 18
provides conversion formulas.
Table 18 Value Conversions
Parameter Units Reported (X) Units Conversion Formula
receivedPower 1 DSP Receive Signal Strength Same Same
totalGain 1 0.5 dB dB X/2
gainSettingIF 1 0.5 dB dB X/2
gainSettingRF 1 2
(-16)
dB dB X/2
16
constVariance 86016/(10
(0.1*SNRdb)
) SNR in dB 10 * log10(86016/X)
freqOffset 11.71875/2
16
kHz kHz X/5592.4
syncStatus No units Same Same
timingOffset In samples Same Same
receivedPower 2 DSP Receive Signal Strength Same Same
totalGain 2 0.5 dB dB X/2
gainSettingIF 2 0.5 dB dB X/2
gainSettingRF 2 2
(-16)
dB dB X/2
16
in 1 SINR = 10*log10(x/2
16
) + 9 SINR in dB 10 * log10(2
16
/X) + 9