Installation guide
Table Of Contents
- CiscouBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation an...
- If You Need More Information
- Wireless Modem Card and Subsystem Overview
- Field-Replaceable Units
- Installation Prerequisites
- Removing and Installing the Wireless Modem Card
- Installing the Power Feed Panel
- Configuring a Wireless Modem Card
- Command Reference
- Syntax Conventions
- Startup Commands
- Installation and Configuration Commands
- Operating Commands
- Monitoring the System
- Troubleshooting
- show controllers radio
- radio histogram
- radio byteErrorHist
- show interfaces radio (histspec)
- show interfaces radio (histdata)
- debug radio
- Images and Image Repositories
- radio image-add
- radio image-move
- show interfaces radio (imagehdr)
- show radio repository
- radio snapshot
- radio scope-output
- radio timeline
- show interfaces radio (tlspec)
- show interfaces radio (tldata)
- Regulatory Compliance and Safety Information
- FCC Registration and Requirements
- Translated Safety Warnings
- Short-Circuit Protection Warning
- Disconnect Device Warning
- Lightning Activity Warning
- Installation Warning
- Jewelry Removal Warning
- Supply Circuit Warning
- Service Personnel Warning
- Product Disposal Warning
- Faceplates and Cover Panel Requirement
- Chassis—Rack-Mounting and Servicing Warning
- Restricted Area Warning
- Earthed Conductor Warning
- Power Cabling Warning
- Ground Connection Warning
- Power Supply Wiring Warning
- Copper Conductors Warning
- Exposed DC Power Wire Warning
- 48 VDC Power System Warning
- SELV-IEC 60950 DC Power Supply Warning
- DC Power Disconnection Warning
- DC Input Wiring Warning
- Ground Wire Connection Warning
- Ground Conductor Warning
- No. 26 AWG Wire Warning
- Coaxial Cable Specification Warning
- Transverter Location Warning
- Obtaining Documentation
- Obtaining Technical Assistance
85
Cisco uBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation and Configuration
78-6030-03
Command Reference
Link Management Messages
This command causes the contents of the Link Management and BPI messages to be dumped in a
formatted fashion as they are transmitted or received.
Note The meanings of these fields are documented in the Data Over Cable System Interface Specification
(DOCSIS) standards.
UBR04(config-if)# debug radio messages
Following is an example of the results:
00:01:35: Message type (0x0C): BPKM-REQ msgLEN: 133
00:01:35 BPKM Code (0x04): Auth Request Identifier: 0x00 Length: 129
00:01:35 Attribute Type (0x04): RSA-Public-Key Length: 126
00:01:35: 307C 300D 0609 2A86 4886 F70D 0101 0105
00:01:35: 0003 6B00 3068 0261 00B1 5407 9843 23EA
00:01:35: 74A9 3E26 07C7 686D BCA0 94ED E388 14C3
00:01:35: B4D7 BE5E F0DA 39C1 BBC6 9A5B 6259 2F82
00:01:35: D0A7 0704 3B61 BB61 5F10 0600 D198 3DD2
00:01:35: 9DAB 0C50 2DDA 6DDC A0F0 128E 4C00 2C6F
00:01:35: C3FC D596 2207 20F9 C58B B777 5BDC D786
00:01:35: E60D B8EF 7484 9B1F 7B02 0301 0001
Physical Layer Messages
This command causes various physical layer entities to log debug output:
UBR04(config-if)# debug radio phy cwrLog modName
modName values are described below:
image Modules related to image management (open, close, rewind).
download Modules related to the download task.
chip Modules related to chip management.
message Modules related to cwrMessage.
task Modules related to the internal cwrTask management layer.
state Modules related to generic state machine.
file Modules related to the internal cwrFile layer.
card Modules related to the card object as a whole.
subsystem Modules related to subsystems, such as dsp, fir, and arq.
repository Modules related to the image repository.