Installation guide
Table Of Contents
- CiscouBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation an...
- If You Need More Information
- Wireless Modem Card and Subsystem Overview
- Field-Replaceable Units
- Installation Prerequisites
- Removing and Installing the Wireless Modem Card
- Installing the Power Feed Panel
- Configuring a Wireless Modem Card
- Command Reference
- Syntax Conventions
- Startup Commands
- Installation and Configuration Commands
- Operating Commands
- Monitoring the System
- Troubleshooting
- show controllers radio
- radio histogram
- radio byteErrorHist
- show interfaces radio (histspec)
- show interfaces radio (histdata)
- debug radio
- Images and Image Repositories
- radio image-add
- radio image-move
- show interfaces radio (imagehdr)
- show radio repository
- radio snapshot
- radio scope-output
- radio timeline
- show interfaces radio (tlspec)
- show interfaces radio (tldata)
- Regulatory Compliance and Safety Information
- FCC Registration and Requirements
- Translated Safety Warnings
- Short-Circuit Protection Warning
- Disconnect Device Warning
- Lightning Activity Warning
- Installation Warning
- Jewelry Removal Warning
- Supply Circuit Warning
- Service Personnel Warning
- Product Disposal Warning
- Faceplates and Cover Panel Requirement
- Chassis—Rack-Mounting and Servicing Warning
- Restricted Area Warning
- Earthed Conductor Warning
- Power Cabling Warning
- Ground Connection Warning
- Power Supply Wiring Warning
- Copper Conductors Warning
- Exposed DC Power Wire Warning
- 48 VDC Power System Warning
- SELV-IEC 60950 DC Power Supply Warning
- DC Power Disconnection Warning
- DC Input Wiring Warning
- Ground Wire Connection Warning
- Ground Conductor Warning
- No. 26 AWG Wire Warning
- Coaxial Cable Specification Warning
- Transverter Location Warning
- Obtaining Documentation
- Obtaining Technical Assistance
70
Cisco uBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation and Configuration
78-6030-03
Command Reference
Example
The following command will display the 1-hour link metrics for the wireless modem card in slot 6, port
0 of the Cisco uBR7200 series router:
UBR04(config-if)# show interfaces radio 6/0 1hour-metrics
One hour statistics (cumulative). Captured at 12:33:01 UTC Tue May 25 1999
=====|=========|==========|==========|==========|==========|==========|
Hour| Time | EFS | ES | SES | CSES | DM |
Ago | | | | | | |
=====|=========|==========|==========|==========|==========|==========|
1 16:00:23 57599 1 1 0 0
=========|==========|===================|
Pre ARQ | Post ARQ | Total |
Cwd Err | Cwe Err | Codewords |
=========|==========|===================|
1 0 1506296619
When 1minute-metrics are requested, a table of values for the last 60 minutes are displayed. Values are
cumulative—every successive row is the sum of the corresponding values in the previous row plus the
values determined for the 1-minute period represented by that row. The values displayed are identical to
those displayed for 1hour-metrics, except that the period is 1 minute.
When 1second-metrics is requested, a table of values for the last 60 seconds is displayed. Values are
cumulative—every successive row is the sum of the corresponding values in the previous row plus the
values determined for the 1-second period represented by that row.
Note If the delta option is specified, the values displayed represent the differences between the previous
row and the current row.
The following values are displayed:
Post ARQ
Errored Codewords
Represents the post-ARQ errored codewords detected in the last 1 hour. This
is the number of codewords not passed to the protocol control information
(PCI) physical layer by the ARQ because they remained uncorrected even after
ARQ.
Total Codewords Represents the total number of codewords received on this link in the last 1
hour.
Sec Ago Represents how long ago (in seconds) this entry was captured.
Total Codewords Represents the total number of codewords received on this link in the
last 1 second.
Pre ARQ Codeword Errors Represents the pre-ARQ errored codewords detected in the last 1
second. This is the number of Reed-Solomon codeword errors
indicated by the codec to the ARQ.