Installation guide
Table Of Contents
- CiscouBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation an...
- If You Need More Information
- Wireless Modem Card and Subsystem Overview
- Field-Replaceable Units
- Installation Prerequisites
- Removing and Installing the Wireless Modem Card
- Installing the Power Feed Panel
- Configuring a Wireless Modem Card
- Command Reference
- Syntax Conventions
- Startup Commands
- Installation and Configuration Commands
- Operating Commands
- Monitoring the System
- Troubleshooting
- show controllers radio
- radio histogram
- radio byteErrorHist
- show interfaces radio (histspec)
- show interfaces radio (histdata)
- debug radio
- Images and Image Repositories
- radio image-add
- radio image-move
- show interfaces radio (imagehdr)
- show radio repository
- radio snapshot
- radio scope-output
- radio timeline
- show interfaces radio (tlspec)
- show interfaces radio (tldata)
- Regulatory Compliance and Safety Information
- FCC Registration and Requirements
- Translated Safety Warnings
- Short-Circuit Protection Warning
- Disconnect Device Warning
- Lightning Activity Warning
- Installation Warning
- Jewelry Removal Warning
- Supply Circuit Warning
- Service Personnel Warning
- Product Disposal Warning
- Faceplates and Cover Panel Requirement
- Chassis—Rack-Mounting and Servicing Warning
- Restricted Area Warning
- Earthed Conductor Warning
- Power Cabling Warning
- Ground Connection Warning
- Power Supply Wiring Warning
- Copper Conductors Warning
- Exposed DC Power Wire Warning
- 48 VDC Power System Warning
- SELV-IEC 60950 DC Power Supply Warning
- DC Power Disconnection Warning
- DC Input Wiring Warning
- Ground Wire Connection Warning
- Ground Conductor Warning
- No. 26 AWG Wire Warning
- Coaxial Cable Specification Warning
- Transverter Location Warning
- Obtaining Documentation
- Obtaining Technical Assistance

54
Cisco uBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation and Configuration
78-6030-03
Command Reference
radio privacy {enable | auth-wait-time secs | reauth-wait-time secs | auth-grace-time secs |
op-wait-time secs | rekey-wait-time secs | tek-grace-time secs | auth-lifetime secs | tek-lifetime secs}
no radio privacy
Syntax Description
Example
The following command will configure baseline privacy:
UBR04(config-if)# radio privacy enable
radio duplexor
The duplexer is a mechanical device that acts as a band pass filter when installed in the wireless
transverter. This filter restricts the transverter to operate in a specified part of the frequency spectrum.
One duplexer provides a high- and low-frequency specification for one wireless transverter.
Use this command in interface configuration mode to enter duplexer specifications.
Note This command should be entered each time the frequency specifications are changed.
radio duplexor antenna_num PartNum LoPassbandRange HiPassbandRange RxPassband
[low-passband | hi-passband] CLEIcode VendorName SerialNumber
auth-wait-time The number of seconds the slave radio will wait before issuing a new authorization
request to the master radio.
reauth-wait-time The number of seconds the slave radio will wait before issuing a new
reauthorization request to the master.
auth-grace-time Grace time for an authorization key. The slave radio is expected to start trying to
get a new authorization key beginning auth-grace-time seconds before the
authorization key actually expires.
op-wait-time Operational wait timeout.
rekey-wait-time The amount of time (in seconds) that the slave radio waits before issuing a new
request to the master radio for an encryption key.
tek-grace-time Grace time for a traffic encryption key (TEK). The slave radio is expected to start
trying to get a new TEK beginning tek-grace-time seconds before the traffic
encryption key actually expires.
auth-lifetime The lifetime (in seconds) the master radio assigns to an authorization key for the
slave radio.
tek-lifetime The lifetime (in seconds) assigned to traffic encryption keys by the master radio.