Installation guide
Table Of Contents
- CiscouBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation an...
- If You Need More Information
- Wireless Modem Card and Subsystem Overview
- Field-Replaceable Units
- Installation Prerequisites
- Removing and Installing the Wireless Modem Card
- Installing the Power Feed Panel
- Configuring a Wireless Modem Card
- Command Reference
- Syntax Conventions
- Startup Commands
- Installation and Configuration Commands
- Operating Commands
- Monitoring the System
- Troubleshooting
- show controllers radio
- radio histogram
- radio byteErrorHist
- show interfaces radio (histspec)
- show interfaces radio (histdata)
- debug radio
- Images and Image Repositories
- radio image-add
- radio image-move
- show interfaces radio (imagehdr)
- show radio repository
- radio snapshot
- radio scope-output
- radio timeline
- show interfaces radio (tlspec)
- show interfaces radio (tldata)
- Regulatory Compliance and Safety Information
- FCC Registration and Requirements
- Translated Safety Warnings
- Short-Circuit Protection Warning
- Disconnect Device Warning
- Lightning Activity Warning
- Installation Warning
- Jewelry Removal Warning
- Supply Circuit Warning
- Service Personnel Warning
- Product Disposal Warning
- Faceplates and Cover Panel Requirement
- Chassis—Rack-Mounting and Servicing Warning
- Restricted Area Warning
- Earthed Conductor Warning
- Power Cabling Warning
- Ground Connection Warning
- Power Supply Wiring Warning
- Copper Conductors Warning
- Exposed DC Power Wire Warning
- 48 VDC Power System Warning
- SELV-IEC 60950 DC Power Supply Warning
- DC Power Disconnection Warning
- DC Input Wiring Warning
- Ground Wire Connection Warning
- Ground Conductor Warning
- No. 26 AWG Wire Warning
- Coaxial Cable Specification Warning
- Transverter Location Warning
- Obtaining Documentation
- Obtaining Technical Assistance
44
Cisco uBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation and Configuration
78-6030-03
Command Reference
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback set
Keepalive set (10 sec)
Last input 00:00:01, output 00:00:01, output hang never
Last clearing of “show interface” counters never
Queueing strategy: fifo
Output queue 0/40, 8 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
620 packets input, 203300 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 output errors, 0 collisions, 4 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
radio self-test
Use this command in interface configuration mode to test the memory and hardware integrity of the
wireless modem card. Use the enable option to execute self-tests each time the card is initiated
(no shut). Use the command without the enable option to perform a self-test only on the first no shut
after initiation. Each time the test is performed, results are displayed on the console.
Use the no version of the command to configure a restart of the link without executing self-tests.
Note Use the show running-configuration interface radio slot/port command to display the current
setting.
radio self-test [enable]
no radio self-test
Syntax Description
Example
The following example shows the configuration command to download and execute self-tests each time
the modem card is enabled:
UBR04(config-if)# radio self-test enable
radio receive-antennas
Use this command in interface configuration mode to configure the wireless modem card to use a
specified number of receive antennas. This command can be entered only when the radio link is down
(shut), and will take effect when the link is again active (no shut). Use the no version of the command
to set the number of receive antennas to 1 (the default value).
Note Before this command can take effect, the receive antennas and wireless transverters must be
available.
enable (Optional) causes execution of self-tests each time the card is initiated.