Installation guide
Table Of Contents
- CiscouBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation an...
- If You Need More Information
- Wireless Modem Card and Subsystem Overview
- Field-Replaceable Units
- Installation Prerequisites
- Removing and Installing the Wireless Modem Card
- Installing the Power Feed Panel
- Configuring a Wireless Modem Card
- Command Reference
- Syntax Conventions
- Startup Commands
- Installation and Configuration Commands
- Operating Commands
- Monitoring the System
- Troubleshooting
- show controllers radio
- radio histogram
- radio byteErrorHist
- show interfaces radio (histspec)
- show interfaces radio (histdata)
- debug radio
- Images and Image Repositories
- radio image-add
- radio image-move
- show interfaces radio (imagehdr)
- show radio repository
- radio snapshot
- radio scope-output
- radio timeline
- show interfaces radio (tlspec)
- show interfaces radio (tldata)
- Regulatory Compliance and Safety Information
- FCC Registration and Requirements
- Translated Safety Warnings
- Short-Circuit Protection Warning
- Disconnect Device Warning
- Lightning Activity Warning
- Installation Warning
- Jewelry Removal Warning
- Supply Circuit Warning
- Service Personnel Warning
- Product Disposal Warning
- Faceplates and Cover Panel Requirement
- Chassis—Rack-Mounting and Servicing Warning
- Restricted Area Warning
- Earthed Conductor Warning
- Power Cabling Warning
- Ground Connection Warning
- Power Supply Wiring Warning
- Copper Conductors Warning
- Exposed DC Power Wire Warning
- 48 VDC Power System Warning
- SELV-IEC 60950 DC Power Supply Warning
- DC Power Disconnection Warning
- DC Input Wiring Warning
- Ground Wire Connection Warning
- Ground Conductor Warning
- No. 26 AWG Wire Warning
- Coaxial Cable Specification Warning
- Transverter Location Warning
- Obtaining Documentation
- Obtaining Technical Assistance
39
Cisco uBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation and Configuration
78-6030-03
Command Reference
Startup Commands
Use these commands to determine the status of the current configuration, and to activate and deactivate
the link:
• show interfaces radio—To display the protocol-specific details supported
• show running-configuration—To display the configuration currently in effect on the
Cisco uBR7200 series router
• show startup-configuration—To display the system startup configuration
• shut, no shut—To shut down and reinstate the link
• write—To write the configuration currently being executed by the router to a specified device
show interfaces radio
Use this command in privileged EXEC mode to display the protocol-specific details supported by the
specified interface. The show interfaces command is also the starting point to display interface-specific
configurations such as thresholds and histograms.
show interfaces radio slot number/port numbe
Syntax Description
Example
The following example shows the display received for a modem card located in slot 3, port 0:
UBR04# show interfaces radio 3/0
Radio 3/0 is up, line protocol is up
Hardware is CWRP2P
Internet address is 192.168.168.233/24
MTU 1500 bytes, BW 44419 Kbit, DLY 11000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive not set
Last input 00:00:58, output 0:00:45, output hang never
Last clearing of “show interface” counters never
Queueing strategy: fifo
Output queue 0/40, 7 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
596 packets input, 197818 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
600 packets output, 198558 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
slot number Positive integer representing the Cisco uBR7200 series slot number
port number Positive integer representing the port number on that slot