Installation guide
Table Of Contents
- CiscouBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation an...
- If You Need More Information
- Wireless Modem Card and Subsystem Overview
- Field-Replaceable Units
- Installation Prerequisites
- Removing and Installing the Wireless Modem Card
- Installing the Power Feed Panel
- Configuring a Wireless Modem Card
- Command Reference
- Syntax Conventions
- Startup Commands
- Installation and Configuration Commands
- Operating Commands
- Monitoring the System
- Troubleshooting
- show controllers radio
- radio histogram
- radio byteErrorHist
- show interfaces radio (histspec)
- show interfaces radio (histdata)
- debug radio
- Images and Image Repositories
- radio image-add
- radio image-move
- show interfaces radio (imagehdr)
- show radio repository
- radio snapshot
- radio scope-output
- radio timeline
- show interfaces radio (tlspec)
- show interfaces radio (tldata)
- Regulatory Compliance and Safety Information
- FCC Registration and Requirements
- Translated Safety Warnings
- Short-Circuit Protection Warning
- Disconnect Device Warning
- Lightning Activity Warning
- Installation Warning
- Jewelry Removal Warning
- Supply Circuit Warning
- Service Personnel Warning
- Product Disposal Warning
- Faceplates and Cover Panel Requirement
- Chassis—Rack-Mounting and Servicing Warning
- Restricted Area Warning
- Earthed Conductor Warning
- Power Cabling Warning
- Ground Connection Warning
- Power Supply Wiring Warning
- Copper Conductors Warning
- Exposed DC Power Wire Warning
- 48 VDC Power System Warning
- SELV-IEC 60950 DC Power Supply Warning
- DC Power Disconnection Warning
- DC Input Wiring Warning
- Ground Wire Connection Warning
- Ground Conductor Warning
- No. 26 AWG Wire Warning
- Coaxial Cable Specification Warning
- Transverter Location Warning
- Obtaining Documentation
- Obtaining Technical Assistance
18
Cisco uBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation and Configuration
78-6030-03
Removing and Installing the Wireless Modem Card
Step 4 With the metal carrier aligned in the slot guides, gently slide the modem card halfway into the modem
card slot.
Caution Do not slide the modem card all the way into the slot until you have connected all required cables.
Trying to do so will disrupt normal operation of the router.
Step 5 With the modem card halfway in the slot, connect all required cables to the front of the modem card.
(See the “Cabling the Wireless Modem Card” section on page 19.)
Step 6 After connecting all required cables, carefully slide the modem card all the way into the slot until you
feel the card’s connectors mate with the midplane.
Step 7 Tighten the captive installation screws on the modem card. (See Figure 8.)
Note If the modem card captive installation screws do not tighten all the way, the card is not
completely seated in the midplane. Carefully pull the modem card halfway out of the slot,
reinsert it, and tighten the captive installation screws.
Caution Care must be taken when installing the wireless modem cards to not overtighten and strip the captive
screws. Never use a screw gun or similar device when installing these cards.
Caution To ensure adequate airflow across the router’s modem cards, a modem card or blank modem card
(faceplate) must be installed in each modem card slot.
Warning
Blank faceplates and cover panels serve three important functions: they prevent exposure to
hazardous voltages and currents inside the chassis; they contain electromagnetic interference
(EMI) that might disrupt other equipment; and they direct the flow of cooling air through the
chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are
in place. To see translations of the warnings that appear in this publication, refer to the
“Regulatory Compliance and Safety Information” section in this document.
This completes the procedure for installing a wireless modem card in the Cisco uBR7200 series router.