Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Cisco UCS C460 Server Installation and Service Guide Covers Server Generation M1 January 26, 2011 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Contents Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Contents Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Power Specifications APPENDIX B A-2 Cable and Power Cord Specifications KVM Cable B-1 B-1 Supported Power Cords and Plugs B-2 AC Power Cord Illustrations B-3 APPENDIX C RAID Controller Considerations C-1 How to Determine Which Controller Is in Your Server C-1 How to Disable Quiet Boot For CIMC Firmware Earlier Than Release 1.
Contents Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Preface This preface describes the audience, organization, and conventions of the Cisco UCS C460 Server Installation and Service Guide. It also provides information about how to obtain related documentation.
Preface Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Conventions This document uses the following conventions for notes, cautions, and safety warnings. Notes and cautions contain important information that you should know. Note Means reader take note. Notes contain helpful suggestions or references to material that are not covered in the publication. Caution Means reader be careful.
Preface Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents.
Preface Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m ¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes.
Preface Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes.
Preface Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Preface Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.
Preface Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m CH A P T E R 1 Overview This chapter provides an overview of the Cisco UCS C460 server features. The Cisco UCS C460 server is a part of the Cisco UCS C-Series rack-mount server family. It is a high-performance, high-memory-capacity server designed with the performance and reliability to power compute-intensive, enterprise-critical standalone applications and virtualized workloads.
Chapter 1 Overview Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Figure 1-2 shows the operations panel LEDs and buttons. Figure 1-2 Operations Panel LEDs and Buttons 3 5 4 6 2 1 ID LED 2 ID button 3 HDD fault LED 4 System health LED 5 Fan fault LED 6 Power status LED 7 Power button 8 Reset button 9 NMI button 197617 7 8 9 1 Figure 1-3 shows the rear panel features.
Chapter 1 Overview Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Table 1-1 lists the features of the C460 server. . Table 1-1 Cisco UCS C460 Server Features Chassis Four rack-unit (4RU) chassis Processors Either 2 or 4 Xeon 7500 Series processors. Two-CPU configurations require 2 power supplies and 4-CPU configurations require 4 power supplies. Memory Up to 64 DIMMs1, populated in 8 slots on each of the 8 memory risers.
Chapter 1 Overview Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Table 1-1 Cisco UCS C460 Server Features (continued) Network and management I/O The server provides these rear-panel connectors: Two dedicated 10/100 Ethernet management ports • Two 1Gb Ethernet ports • Two 10Gb Base-T Ethernet ports • Two 10Gb SFP+ Ethernet ports • See Using the 10 Gb Ports, page 2-12 for more information about the SFP+ and 10GBase-T 10 Gb ports.
Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Chapter 2 Installing the Server Unpacking and Inspecting the Server Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Unpacking and Inspecting the Server Caution When handling server components, wear an ESD strap and handle modules by the carrier edges only. Tip Keep the shipping container in case the server requires shipping in the future. Note The chassis is thoroughly inspected before shipment.
Chapter 2 Installing the Server Preparing for Server Installation Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Chapter 2 Installing the Server Installing the Server In a Rack Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Rack Requirements This section provides the requirements for the standard open racks, assuming an external ambient air temperature range of 32°F to 95°F (0°C to 35°C). The rack must be of the following type: Tip • A standard 19-in. (48.
Chapter 2 Installing the Server Installing the Server In a Rack Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Figure 2-2 Installing the Slide Rail Assemblies in the Rack 1 1 3 4 198153 2 Step 2 1 Rack posts 2 Rear mounting pegs and locking clip 3 Slide rail assembly 4 Front mounting pegs and locking clip d. Attach the second slide-rail assembly to the opposite side of the rack. e.
Chapter 2 Installing the Server Installing the Server In a Rack Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Step 3 Step 4 Insert the server into the slide rails: a. Align the rear of the mounting brackets with the front of the empty slide rails that you installed in Step 1. b. Push the server into the slide rails until it stops at the internal stops. c.
Chapter 2 Installing the Server Initial Server Setup Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Chapter 2 Installing the Server Initial Server Setup Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Note Step 3 Alternatively, you can use the VGA and USB ports on the rear panel. However, you cannot use the front panel console connector VGA and the rear panel VGA at the same time. If you are connected to one VGA connector and you then connect a video device to the other connector, the first VGA connector is disabled.
Chapter 2 Installing the Server Initial Server Setup Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Note d. The Cisco Card NIC mode is currently supported only with a Cisco UCS P81E Virtual Interface Card (N2XX-ACPCI01) that is installed in PCIe slot 1 (see Figure 3-26 on page 3-34). See also Special Considerations for the Cisco UCS P81E Virtual Interface Card (N2XX-ACPCI01), page 3-37. Use this utility to change the NIC redundancy to your preference.
Chapter 2 Installing the Server Initial Server Setup Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Defining Static Network Settings Using a Script File Use the following procedure to create a static network script: Step 1 Use a text editor to create a file named network.cfg. Step 2 Add the following content to network.
Chapter 2 Installing the Server Initial Server Setup Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m NIC Modes and NIC Redundancy Settings This server has the following NIC mode settings that you can choose from: • Dedicated—The two 10/100 management ports are used to access the CIMC. You have to select a NIC redundancy and IP setting. • Shared LOM (default)—The two 1Gb Ethernet ports are used to access the CIMC.
Chapter 2 Installing the Server Initial Server Setup Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Using the 10 Gb Ports This server has four 10 Gb ports on the rear panel (see Figure 1-3 on page 1-2): Two 10GBase-T ports Two SFP+ ports We recommend that you use either the two SFP+ ports or the two 10GBase-T ports. • • Although there are four physical ports, only two can have active PHY links at one time.
Chapter 2 Installing the Server Configuring BIOS Settings and Updating BIOS Firmware Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Chapter 2 Installing the Server Configuring BIOS Settings and Updating BIOS Firmware Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Overview of the BIOS Setup Utility Table 2-1 contains a high-level description of the BIOS setup utility. Note Detailed descriptions of each field in the utility are printed on the individual BIOS screens.
Chapter 2 Installing the Server Configuring BIOS Settings and Updating BIOS Firmware Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Updating the BIOS Firmware You can update the BIOS firmware either by using the EFI interface during bootup, or by updating from a running Windows or Linux operating system (OS).
Chapter 2 Installing the Server Configuring BIOS Settings and Updating BIOS Firmware Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m f. In the Virtual Media Session window, check the check box in the Mapped column for the USB thumb drive that you added, and then wait for mapping to complete. Observe the progress in the Details pane. Step 3 Boot the server and press F6 when prompted to get to the Boot Option screen.
Chapter 2 Installing the Server Configuring BIOS Settings and Updating BIOS Firmware Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Updating the BIOS Firmware from a Linux Operating System Use the following procedure to update the BIOS firmware from a running host OS. Note The required version of the iFlash32 utility that is used in this procedure is iFlash32 Version 1.1, Build 3 or later. This utility is included in the BIOS firmware update package.
Chapter 2 Installing the Server Configuring BIOS Settings and Updating BIOS Firmware Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m iFlash32 Utility Command Options You can use the iFlash32 command with the following options: Note The command syntax shown below is for Linux. For Windows, use “/” in place of “-” for all options.
Chapter 2 Installing the Server Configuring BIOS Settings and Updating BIOS Firmware Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Recovering a Corrupt BIOS There are two ways that you can recover a corrupted BIOS: • You can use the CIMC management interface, either GUI or CLI. For instructions, refer to the Cisco UCS C-Series Rack-Mount Server Configuration Guide or the Cisco UCS C-Series Rack-Mount Server CLI Configuration Guide.
Chapter 2 Installing the Server Configuring BIOS Settings and Updating BIOS Firmware Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Note If you do not remove the jumper, the server forces a recovery of the new BIOS every time that you power cycle the server. Step 14 Replace the top cover. Step 15 Replace the server in the rack, replace cables, and then power on the server by pressing the Power button.
Chapter 2 Installing the Server Configuring BIOS Settings and Updating BIOS Firmware Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Using a Clear BIOS Admin Password Jumper on Header J5C3 The J5C3 jumper is a 3-pin header on the motherboard (see Figure 2-6 on page 2-20). This procedure describes how to clear the Admin password for the BIOS back to the default in case the user-selected password is lost of forgotten.
Chapter 2 Installing the Server Configuring BIOS Settings and Updating BIOS Firmware Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Using a Clear CMOS Jumper on Header J5C2 The J5C3 jumper is a 3-pin header on the motherboard (see Figure 2-6 on page 2-20). You can use this procedure to clear the server’s CMOS settings in the case of a system hang.
Chapter 2 Installing the Server Updating the CIMC Firmware Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Updating the CIMC Firmware The server uses CIMC firmware obtained from and certified by Cisco. After you have downloaded a CIMC firmware image from Cisco, you can use it to update the firmware on your server. Cisco also provides release notes with each firmware image.
Chapter 2 Installing the Server RAID Configurations on Hard Drives Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m CH A P T E R 3 Maintaining the Server This chapter describes how to diagnose server system problems using LEDs.
Chapter 3 Maintaining the Server Status LEDs and Buttons Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Front Panel LEDs Figure 3-1 shows the front panel LEDs.
Chapter 3 Maintaining the Server Status LEDs and Buttons Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Table 3-1 Front Panel LEDs (continued) LED Name State Power supply fault Memory fault CPU fault Network activity • Green—All power supplies are operating properly. • Off—One or more power supplies are not operating properly. • Green—All DIMMs are operating properly. • Off—One or more DIMMs are not operating properly.
Chapter 3 Maintaining the Server Status LEDs and Buttons Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Table 3-2 Operations Panel LEDs LED Name State ID Hard drive fault System health Fan fault Power status • Off—The ID LED is not in use. • Blue and blinking—System ID is active via the remote ID button. • Blue and steady—System ID is active via the local ID button. • Green—No hard drives have a fault.
Chapter 3 Maintaining the Server Status LEDs and Buttons Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Rear Panel LEDs and Buttons Figure 3-3 shows the rear panel LEDs and buttons.
Chapter 3 Maintaining the Server Preparing for Server Component Installation Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Chapter 3 Maintaining the Server Preparing for Server Component Installation Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m • Step 3 Emergency shutdown—Press and hold the Power button for 4 seconds to force the main power off and immediately enter standby mode. Disconnect the power cords from the power supplies in your server to completely power off the server.
Chapter 3 Maintaining the Server Preparing for Server Component Installation Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Replaceable Component Locations This section shows the locations of the components that are discussed in this chapter. The view in Figure 3-5 is from the top down, with the top cover and internal CPU cage removed.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Installing or Replacing Server Components Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Replacing Power Supplies The server can have two or four power supplies. Four power supplies are required for four-CPU configurations.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Replacing the I/O Riser The I/O riser is module that connects to the motherboard and that provides the ports for rear panel connectivity. To install or replace the I/O riser, follow these steps: Step 1 Remove the I/O riser you are replacing. See Figure 3-7: a.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Figure 3-7 Removing and Replacing the I/O Riser 3 2 198883 1 1 Retaining clip 3 I/O riser 2 I/O riser back panel Replacing an eUSB Drive The eUSB drive is a small solid-state flash drive card that connects to the motherboard in either of two eUSB drive connectors.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Step 2 Install a new eUSB drive. a. Align the connector on the underside of the eUSB drive with the empty drive connector on the motherboard and push on both ends of the drive evenly to seat the connector. b. Replace the single mounting screw that secures the eUSB drive to the motherboard standoff. c. Replace the I/O riser.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Replacing a SAS Riser The SAS riser is a RAID controller card that has a designated position and motherboard connector inside the server. To install or replace a SAS riser, follow these steps: Step 1 Note Caution Note Remove the SAS riser you are replacing. See Figure 3-9: a.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m LSI MegaRAID Card Beep Codes Table 3-4 contains a summary of the LSI MegaRAID card beep codes. These beep codes indicate activity and changes from the optimal state of your RAID array. For full documentation on the LSI MegaRAID cards and the LSI utilities, refer to the LSI documentation for your card.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Step 2 Install a new BBU: a. Connect the cable from the SAS riser to the replacement BBU. b. Insert the two retaining clips on the rear of the BBU into the chassis wall slots and slide the BBU toward the chassis rear until it locks into place. c. Replace the memory riser that you removed for clearance.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Replacing the Motherboard CMOS Battery Warning There is danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Replacing CPUs and Heatsinks This server can operate with 2-, 3-, or 4-CPU configurations. Each CPU supports two memory risers (four memory buffers) connected by serial memory interface (SMI). Each memory buffer has two DDR3 memory bus interfaces. Note The minimum CPU configuration is that CPU1 and CPU3 must be installed.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Step 2 Step 3 Caution Caution Note Install a new CPU: a. Insert the replacement CPU in the socket with the arrow on the CPU pointing toward the arrow on the socket. b. Close the CPU retaining lid and clip down the CPU retaining lever.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Replacing Memory Risers The memory risers connect to the motherboard and each riser provides eight DIMM slots. The memory riser is hot-swappable when you use the Attention button, as described in the following procedure.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m e. Replace the top cover. f. Replace the server in the rack and replace any cables.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Figure 3-19 DIMM Slots and Memory Buffers 1D 2D 1C 2C 1 2 1 199466 2A 1A 2B 1B Memory Buffer 1 2 Memory Buffer 2 DIMM Population Rules Following are the DIMM population rules: • The minimum configuration for the server is, at least one matched DIMM pair installed in a memory riser on either CPU1 or CPU2 (see Figure 3-18).
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m DIMM Installation Procedure This section contains the following topics: • Identifying a Faulty DIMM, page 3-27 • DIMM Replacement Procedure, page 3-27 Identifying a Faulty DIMM The memory riser has LEDs on it supper surface that can assist you in isolating a faulty DIMM.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Step 2 b. Remove the top cover as described in “Removing and Replacing the Server Top Cover” section on page 3-7. c. Press the attention button (ATTN BUTTON) on the top of the memory riser that contains the faulty DIMM (see Figure 3-20). d. Wait until the attention LED (ATTN) and the power LED turn off. e.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Replacing Fan Modules The eight fan modules in the server are numbered as follows when you are facing the front of the server. Each fan module has a fault LED that lights amber when the fan module fails.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Figure 3-23 Removing and Replacing Fan Modules 1 198934 2 1 Fan module release latches 2 Fan module, front view showing connector on underside of the module Replacing Hard Drives or Solid State Drives Tip You can mix SAS and SATA drives in the same server.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Install a new drive: a. Place a new hard drive in the empty drive tray and replace the four drive tray screws. b. Insert the drive tray into the empty drive bay. c. Push the tray into the slot until the drive connectors are fully seated in the backplane. d. Press the ejector lever flat to lock the drive and tray in place.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Replacing a DVD Drive Warning Class 1 laser product. Statement 1008 To replace or install a DVD drive, follow these steps: Step 1 Caution Step 2 Remove the DVD drive that you are replacing. See Figure 3-25: a. Power off the server as described in Shutting Down and Powering Off the Server, page 3-6. b.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Replacing a PCIe Card Note If you are installing a Cisco UCS P81E Virtual Interface Card (N2XX-ACPCI01), there are prerequisite considerations. See Special Considerations for the Cisco UCS P81E Virtual Interface Card (N2XX-ACPCI01), page 3-37. This server has 10 PCIe expansion slots.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m “Gen nxn” is the electrical lane width and “xn connector” is the mechanical length of the connector. The card length is the supported length because of internal clearance. All PCIe slots are standard-height and require a standard-height mounting bracket on the PCIe card. CPU3 must be installed to support PCIe slots 5, 6, 7, 9, and 10.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Replacing a PCIe Card in a Hot-Swappable Slot To install or replace a PCIe card in slots 1, 2, 6, or 7, follow these steps: Step 1 Remove a hot-swappable PCIe card: a. Note Caution You might have to detach cables from the rear panel to provide clearance.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Special Considerations for the Cisco UCS P81E Virtual Interface Card (N2XX-ACPCI01) The Cisco UCS P81E Virtual Interface Card is a standard-profile, half-length, dual-port 10 Gb PCIe card with SFP+. See the following special considerations and prerequisites. • This server supports installation of up to two of these cards.
Chapter 3 Maintaining the Server Installing or Replacing Server Components Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m A P P E N D I X A Server Specifications This appendix lists the technical specifications for the Cisco UCS C460 server and includes the following sections: • Physical Specifications, page A-1 • Environmental Specifications, page A-2 • Power Specifications, page A-2 Physical Specifications Table A-1 lists the physical specifications for the server.
Appendix A Server Specifications Environmental Specifications Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Environmental Specifications Table A-2 lists the environmental specifications for the server.
Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Appendix B Cable and Power Cord Specifications Supported Power Cords and Plugs Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Supported Power Cords and Plugs Each power supply has a separate power cord. Standard power cords or jumper power cords are available for connection to a power distribution unit that has IEC 60320 C19 outlet receptacles. The jumper power cords, for use in racks, are available as an optional alternative to the standard power cords.
Appendix B Cable and Power Cord Specifications Supported Power Cords and Plugs Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Table B-1 Supported Power Cords for the Server (continued) Length Description Feet Meters Power Cord Reference Illustration CAB-AC-250V/13A Power Cord, 250 VAC 13 A IEC60320 Plug North America 6.6 2.0 Figure B-11 CAB-N5K6A-NA Power Cord, 250 VAC 13 A NEMA 6-15 Plug, North America 8.2 2.
Appendix B Cable and Power Cord Specifications Supported Power Cords and Plugs Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m SFS-250V-10A-CN Plug: EL 218 (CCEE GB2009) Cordset rating 10A, 250V (2500 mm) Connector: EL 701 (IEC60320/C13) CAB-9K10A-EU Plug: M2511 Cordset rating: 10A/16 A, 250 V Length: 8 ft 2 in. (2.
Appendix B Cable and Power Cord Specifications Supported Power Cords and Plugs Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Figure B-7 SFS-250V-10A-IS EL-212 16A 250V Cordset rating 10A, 250V/500V MAX (2500 mm) Connector: EL 701B (IEC60320/C13) Figure B-8 186574 Plug: EL 212 (SI-32) CAB-9K10A-IT Connector C15M (EN60320/C15 ) 186575 Plug: I/3G (CEI 23-16) Cordset rating: 10 A, 250 V Length: 8 ft 2 in. (2.
Appendix B Cable and Power Cord Specifications Supported Power Cords and Plugs Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m Figure B-10 CAB-9K10A-UK Plug: EL 210 (BS 1363A) 13 AMP fuse Figure B-11 Connector: EL 701C (EN 60320/C15) 186580 Cordset rating: 10 A, 250 V/500 V MAX Length: 2500mm CAB-AC-250V/13A Connector: EL 701 (IEC60320/C13) Plug: EL312MoldedTwistlock (NEMA L6-20) CAB-N5K6A-NA Plug: NEMA 6-15P Cordset rating: 10 A, 250 V Length: 8.
Appendix B Cable and Power Cord Specifications Supported Power Cords and Plugs Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Appendix B Cable and Power Cord Specifications Supported Power Cords and Plugs Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m A P P E N D I X C RAID Controller Considerations This appendix provides RAID controller information, and it includes the following sections: • How to Determine Which Controller Is in Your Server, page C-1 • How to Disable Quiet Boot For CIMC Firmware Earlier Than Release 1.
Appendix C RAID Controller Considerations How to Disable Quiet Boot For CIMC Firmware Earlier Than Release 1.2(1) Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o . c o m How to Disable Quiet Boot For CIMC Firmware Earlier Than Release 1.2(1) For CIMC firmware and BIOS release 1.2(1) and later, Quiet Boot has been removed. If you are running CIMC firmware and BIOS earlier than release 1.2(1), you can use the following procedure to disable Quiet Boot.
INDEX conventions, text Numerics i-viii CPUs and heatsinks, replacing 10G Base-T ports 2-12 10Gb port architecture, graphic 10 Gb ports 3-20 2-12 D 2-12 DHCP, enabling 2-9 DIMMs B performance guidelines battery backup unit, see SAS riser battery beep codes for LSI MegaRAID beeps for USB devices 3-16 3-16 population rules DIMMs, replacing 2-7 3-25 3-25 disabling Quiet Boot BIOS C-2 documentation, related clearing CMOS jumper 2-22 determining current version iFlash32 utility options
Index Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Index Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
Index Se n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a ck @ c i s c o .
