Specifications

ManualsBrandsCisco ManualsComputer equipmentuBR10012 Universal Broadband Router UBR10-FAN-CAB=

AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router

78-13996-01 Rev. B0

AC Power Entry Module for the

Cisco uBR10012 Universal Broadband Router

UBR10-PWR-AC, UBR10-PWR-AC=,

78-13996-01 Rev. B0

June 10, 2002

This document describes the AC power entry module (AC PEM) and how to install it in the

Cisco uBR10012 universal broadband router. This document provides the following information:

• Feature Overview, page 1

• Safety Information and Warnings, page 6

• Removing and Replacing an AC PEM, page 10

• Technical Specifications, page 23

• Obtaining Documentation, page 23

• Obtaining Technical Assistance, page 24

Feature Overview

The Cisco uBR10012 router can optionally ship with two AC power entry modules (PEMs) that provide

a redundant power supply to the system. One AC PEM can provide sufficient power for a fully configured

chassis, so that if one AC PEM fails, the other automatically begins providing power for the entire router,

without impacting system operations.

Note You should be using Cisco IOS Release 12.2(4)XF1, Cisco IOS Release 12.2(4)BC1a, or a later

release when using the AC PEM. If using an earlier release, the show environment command will

not correctly identify the AC PEM’s error messages.

Caution The Cisco uBR10012 router supports using either the AC PEM or the DC PEM, but it does not

support mixing AC and DC PEMs. Both PEMs must be either AC PEMs or DC PEMs.

The AC PEMs use standard 200–240 VAC (50/60 Hz) input power obtained through power receptacles

on the front panel of each PEM. The two AC PEMs convert the AC power to provide filtered, redundant,

and load shared DC power to the Cisco uBR10012 chassis.

Summary of content (26 pages)

PAGE 1
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router UBR10-PWR-AC, UBR10-PWR-AC=, 78-13996-01 Rev. B0 June 10, 2002 This document describes the AC power entry module (AC PEM) and how to install it in the Cisco uBR10012 universal broadband router.
PAGE 2
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Feature Overview Caution Tips The AC PEMs cannot be used with a 100–120 VAC input power source. For fully redundant power protection, use either an uninterruptible power supply (UPS) or a separate AC-input power source for each AC PEM. This document contains the procedures to replace an existing second (redundant) AC PEM and to replace both AC PEMs.
PAGE 3
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Feature Overview Figure 2 shows a Cisco uBR10012 router with dual AC PEMs installed.
PAGE 4
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Feature Overview LEDs Table 1 describes the LEDs on the AC PEM. Table 1 AC PEM LEDs and Their Function LED Color Description Power Green The PEM is on, is receiving power from the AC power source, and is providing power to the Cisco uBR10012 chassis (normal operations).
PAGE 5
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Feature Overview Figure 3 Airflow Through the Cisco uBR10012 Chassis with Dual AC PEMs CISCO 10000 POWER CISCO 10000 FAULT C O N S O POWER C LE O N S O LE AU X AU X FAULT A C TIV IT TH Y E LIN RN E T K A C E 1 OT 0 OT SL SL 1 OT 0 OT SL SL TIV IT Y E TH E LIN RN K ET ALARMS ALARMS A C O A C O C R IT IC C A M R L A IT IC JO R IN O R TA TU S FA IL L A JO R M IN O R S T
PAGE 6
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Safety Information and Warnings Power Supply Cables The AC PEM requires different power supply cables, depending on the country of operation. Table 2 lists the product order numbers for the power supply cables that are available for the AC PEM for the Cisco uBR10012 universal broadband router.
PAGE 7
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Safety Information and Warnings Varoitus Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista.
PAGE 8
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Safety Information and Warnings ¡Advertencia! Este símbolo de aviso significa peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y familiarizarse con los procedimientos estándar de prevención de accidentes.
PAGE 9
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Safety Information and Warnings Electrical Equipment Guidelines Follow these basic guidelines when working with any electrical equipment: • Before beginning any procedures requiring access to the chassis interior, locate the emergency power-off switch for the room in which you are working. • Disconnect all power and external cables before moving a chassis. • Do not work alone when potentially hazardous conditions exist.
PAGE 10
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Removing and Replacing an AC PEM Removing and Replacing an AC PEM This section contains information on removing and replacing AC PEM modules in the Cisco uBR10012 chassis. Tip The AC PEM is operating correctly when its Power LED is on (green). When the Fault LED is on (yellow), the AC PEM is receiving AC-input power but is not providing power to the system.
PAGE 11
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Removing and Replacing an AC PEM Figure 4 CISCO 10000 Location of DC Power Connectors and DC Power Cables CISCO 10000 C O N S O C LE O N S O LE AU X AU X A C TIV A C TIV IT 1 OT 0 OT Y E TH E LIN RN K ET SL SL 1 OT 0 OT SL SL IT E TH Y E LIN RN E T K RTN (+ ) ALARMS ALARMS A C O A C O C R IT IC C A M R L A IT IC JO R IN O R TA TU S FA IL L A JO R M IN O R S TA TU S
PAGE 12
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Removing and Replacing an AC PEM Tip If you want to replace both AC PEMs without shutting down the router, repeat this procedure for each AC PEM, one at a time. Do not use this procedure if both AC PEMs have failed; instead, use the procedure in the “Replacing Both AC PEMs” section on page 16. Step 1 Remove the front cover by lifting it up slightly and then pulling it toward you.
PAGE 13
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Removing and Replacing an AC PEM Figure 6 Removing the AC PEM POWER CISCO 10000 CISCO 10000 FAULT POWER C O N S O C LE O N S O LE AU X AU X FAULT A C A C 1 OT 0 OT TIV IT Y E TH E LIN RN K ET SL SL 1 OT 0 OT SL SL TIV IT E TH Y E LIN RN E T K ALARMS ALARMS A C O A C O C R IT IC C A M R L A IT IC JO R IN O R TA TU S FA IL L A JO R M IN O R S TA TU S FA 62523 IL PER
PAGE 14
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Removing and Replacing an AC PEM Figure 7 Installing the AC PEM POWER CISCO 10000 CISCO 10000 FAULT POWER C O N S O C LE O N S O LE AU X AU X FAULT A C A C 1 OT 0 OT TIV IT Y E TH E LIN RN K ET SL SL 1 OT 0 OT SL SL TIV IT E TH Y E LIN RN E T K ALARMS ALARMS A C O A C O C R IT IC C A M R L A IT IC JO R IN O R TA TU S FA IL L A JO R M IN O R S TA TU S FA 62524 IL P
PAGE 15
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Removing and Replacing an AC PEM Figure 8 Routing the AC Power Cables POWER CISCO 10000 CISCO 10000 FAULT POWER C O N S O C LE O N S O LE AU X FAULT AU X A C A C TIV IT Y 1 OT 0 OT E TH E LIN RN K ET SL SL 1 OT 0 OT SL SL TIV IT E TH Y E LIN RN E T K ALARMS ALARMS A C O A C O C R IT IC C A M R L A IT IC JO R IN O R TA TU S FA IL L A JO R M IN O R S TA TU S FA 7
PAGE 16
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Removing and Replacing an AC PEM Figure 9 Setting AC Power Switch to the ON Position ALARMS ALARMS A C O A C O C R IT IC C A M IT IC JO R O R TA TU S FA IL L A JO R M IN O R S TA TU S FA IL PERFORMANCE ROUTING ENGINE S A M PERFORMANCE ROUTING ENGINE IN AC SWITCH R L A M AC SWITCH AC SWITCH ACINPUT 200-240V 13A 50/60 Hz ACINPU T 200-240 13A 50/6 V 0Hz 62671 ACINPUT 200-240V 13A 50/60 Hz
PAGE 17
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Removing and Replacing an AC PEM Figure 10 Turning the AC PEM Off ALARMS ALARMS A C O A C O C R IT IC C A M IT IC JO R O R TA TU S FA IL L A JO R M IN O R S TA TU S FA IL PERFORMANCE ROUTING ENGINE S A M PERFORMANCE ROUTING ENGINE IN AC SWITCH R L A M AC SWITCH AC SWITCH ACINPUT 200-240V 13A 50/60 Hz ACINPU T 200-240 13A 50/6 V 0Hz 77142 ACINPUT 200-240V 13A 50/60 Hz Step 3 Tips Step
PAGE 18
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Removing and Replacing an AC PEM Figure 11 Removing the AC PEM POWER CISCO 10000 CISCO 10000 FAULT POWER C O N S O C LE O N S O LE AU X AU X FAULT A C A C 1 OT 0 OT TIV IT Y E TH E LIN RN K ET SL SL 1 OT 0 OT SL SL TIV IT E TH Y E LIN RN E T K ALARMS ALARMS A C O A C O C R IT IC C A M R L A IT IC JO R IN O R TA TU S FA IL L A JO R M IN O R S TA TU S FA 62523 IL PE
PAGE 19
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Removing and Replacing an AC PEM Figure 12 Installing the AC PEM POWER CISCO 10000 CISCO 10000 FAULT POWER C O N S O C LE O N S O LE AU X AU X FAULT A C A C 1 OT 0 OT TIV IT Y E TH E LIN RN K ET SL SL 1 OT 0 OT SL SL TIV IT E TH Y E LIN RN E T K ALARMS ALARMS A C O A C O C R IT IC C A M R L A IT IC JO R IN O R TA TU S FA IL L A JO R M IN O R S TA TU S FA 62524 IL
PAGE 20
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Removing and Replacing an AC PEM Figure 13 Routing the AC Power Cables POWER CISCO 10000 CISCO 10000 FAULT POWER C O N S O C LE O N S O LE AU X FAULT AU X A C A C TIV IT Y 1 OT 0 OT E TH E LIN RN K ET SL SL 1 OT 0 OT SL SL TIV IT E TH Y E LIN RN E T K ALARMS ALARMS A C O A C O C R IT IC C A M R L A IT IC JO R IN O R TA TU S FA IL L A JO R M IN O R S TA TU S FA
PAGE 21
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Removing and Replacing an AC PEM Figure 14 Setting AC Power Switch to the ON Position ALARMS ALARMS A C O A C O C R IT IC C A M IT IC JO R O R TA TU S FA IL L A JO R M IN O R S TA TU S FA IL PERFORMANCE ROUTING ENGINE S A M PERFORMANCE ROUTING ENGINE IN AC SWITCH R L A M AC SWITCH AC SWITCH ACINPUT 200-240V 13A 50/60 Hz ACINPU T 200-240 13A 50/6 V 0Hz 62671 ACINPUT 200-240V 13A 50/60 Hz
PAGE 22
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Troubleshooting the PEM Troubleshooting the PEM Check the following to help isolate a problem with the power subsystem: • Is the Power LED on each AC PEM on (green)? – If yes, the PEM is connected to an active 240 VAC AC power source and is supplying power to the chassis. – If the Power LED is not on, and if no other LEDs are on, verify that the AC power source is providing valid power.
PAGE 23
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Technical Specifications Technical Specifications Table 3 lists the specifications for the AC PEM. Table 3 Cisco uBR10000 AC Power Entry Module Specifications Description Product order number Dimensions Specifications • UBR10-PWR-AC (Primary) • UBR10-PWR-AC\R (Redundant) • UBR10-PWR-AC= (Spare) • Height: 19.25 in. (48.894 cm) • Width: 6 in. (15.24 cm) • Depth: 5 in. (12.4 cm) Weight 14.7 lbs (6.
PAGE 24
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Obtaining Technical Assistance Documentation CD-ROM Cisco documentation and additional literature are available in a Cisco Documentation CD-ROM package, which is shipped with your product. The Documentation CD-ROM is updated monthly and may be more current than printed documentation. The CD-ROM package is available as a single unit or through an annual subscription.
PAGE 25
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Obtaining Technical Assistance Cisco.com Cisco.com is the foundation of a suite of interactive, networked services that provides immediate, open access to Cisco information, networking solutions, services, programs, and resources at any time, from anywhere in the world. Cisco.
PAGE 26
AC Power Entry Module for the Cisco uBR10012 Universal Broadband Router Obtaining Technical Assistance If you cannot resolve your technical issues by using the Cisco TAC Web Site, and you are a Cisco.com registered, you can open a case online by using the TAC Case Open tool at the following URL: http://www.cisco.com/tac/caseopen If you have Internet access, it is recommended that you open P3 and P4 cases through the Cisco TAC Web Site.