6-Port and 24-Port 10/100/1000 Gigabit Switches Use this guide to install the following products: SR2016 SR2024 16-Port 10/100/1000 Gigabit Switch 24-Port 10/100/1000 Gigabit Switch User Guide
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2003 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.
Table of Contents Chapter 1: Introduction r Chapter 1: Introduction The 10/100/1000 Switch Features 1 1 1 Chapter 2: Getting to Know the 10/100/1000 Gigabit Switch Overview The 16-Port or 24-Port Switch’s Front Panel The 16-Port or 24-Port Switch’s Back Panel The 16-Port Switch’s Side Panel 2 2 2 3 3 Chapter 3: Connecting the 10/100/1000 Gigabit Switch Overview Connecting Network Devices Placement Options for the 16-Port Switch Placement Options for the 24-Port Switch 4 4 5 6 6 Appendix A: Glossary
Chapter 2: Getting to Know the 10/100/1000 Gigabit Switch The 16-Port or 24-Port Switch’s Back Panel Overview Figure 2-2 The 16- and 24-Port 10/100/1000 Gigabit Switches differ in number of LEDs and ports. The 16-Port Switch has a security slot, while the 24-Port Switch has two gigabit interface converter (GBIC) module slots. The 16-Port or 24-Port Switch’s Front Panel The power port is located on the back panel of the Switch. (power) The power port is where you will connect the included power cord.
Chapter 3: Connecting the 10/100/1000 Gigabit Switch Your Network Connecting Network Devices To connect network devices to the Switch, follow these instructions: 1. Make sure all the devices you will connect to the Switch are powered off. Layout Overview This chapter will explain how to connect network devices to the Switch. For an example of a typical network configuration, see the application diagram shown in Figure 3-1. 2.
Placement Options for the 16-Port Switch Appendix A: Glossary There are three ways to physically install the 16-Port Switch: set the Switch on its four rubber feet, mount the Switch in a standard-sized, 1U high rack, or hang the Switch on a wall using its wall-mount slots. 10BaseT - An Ethernet standard that uses twisted wire pairs. To rack mount the Switch, follow these instructions: 100BaseTX - IEEE physical layer specification for 100 Mbps over two pairs of Category 5 UTP or STP wire. 1.
Fast Ethernet - A 100 Mbps technology based on the 10Base-T Ethernet CSMA/CD network access method. Appendix B: Specifications Hub - The device that serves as the central location for attaching wires from workstations. Can be passive, where there is no amplification of the signals; or active, where the hubs are used like repeaters to provide an extension of the cable that connects to a workstation.
Appendix C: Warranty Information Environmental Dimensions SR2016 SR2024 11.00" x 1.75" x 9.45" (279.4 mm x 44.5 mm x 240 mm) 17.01" x 1.75" x 13.74" (432 mm x 44.5 mm x 349 mm) Unit Weight SR2016 SR2024 4.75 lbs. (2.155 kg) 7.98 lbs. (3.621 kg) Power SR2016 SR2024 12V DC / 500 mA 110-120V AC, 100 W Certifications FCC Class B, CE Operating Temp. 0ºC to 50ºC (32ºF to 122ºF) Storage Temp.
Appendix D: Contact Information For help with the installation or operation of this 10/100/1000 Gigabit Switch, contact Linksys Technical Support at one of the phone numbers or Internet addresses below. Sales Information Technical Support RMA (Return Merchandise Authorization) Issues Fax E-mail Web FTP Site 800-546-5797 (LINKSYS) 800-326-7114 www.linksys.com (or call 949-271-5461) 949-265-6655 support@linksys.com http://www.linksys.com ftp.linksys.com http://www.linksys.
