Specifications

6-9
Cisco AS5x00 Case Study for Basic IP Modem Services
11/24/1999
Section 6 Modem Management Operations
Managing Modem Firmware
In the previous example, the specified SPE range gets updated with new firmware in batches of six
modems at a time. If double density modems were installed, batches of 12 modems would be updated.
Note below that the SPE range 1/0 to 1/7 is mapped to firmware 2.7.1.0. However, SPE range 2/0
through 2/7 is still mapped to the firmware that is bundled with the Cisco IOS.
!
spe 1/0 1/7
firmware location flash:mica-modem-pw.2.7.1.0.bin
spe 2/0 2/7
firmware location system:/ucode/mica_port_firmware
!
The following MICA example is for the
copy
source
modem
command. Unlike the
spe
command, the
numbers 1/0-1/5 refer to specific
modem numbers
(slot/port). The
busyout
keyword will gracefully
busy out the modems if the modems are off hook.
cisco#copy bootflash modem
Source filename []? mica-modem-pw.2.6.2.0.bin
Modem Numbers (<slot>/<port> | group <number> | all)? 1/0-1/5
Type of service [busyout/reboot/recovery] busyout
Allow copy of "bootflash:mica-modem-pw.2.6.2.0.bin" to modems? [yes/no]yes
cisco#
2d05h: %MODEM-5-DL_START: Modem (1/0) started firmware download
2d05h: %MODEM-5-DL_START: Modem (1/1) started firmware download
2d05h: %MODEM-5-DL_START: Modem (1/2) started firmware download
2d05h: %MODEM-5-DL_START: Modem (1/3) started firmware download
2d05h: %MODEM-5-DL_START: Modem (1/4) started firmware download
2d05h: %MODEM-5-DL_START: Modem (1/5) started firmware download
2d05h: %MODEM-5-DL_GOOD: Modem (1/0) completed firmware download:
2d05h: %MODEM-5-DL_GOOD: Modem (1/1) completed firmware download:
2d05h: %MODEM-5-DL_GOOD: Modem (1/2) completed firmware download:
2d05h: %MODEM-5-DL_GOOD: Modem (1/3) completed firmware download:
2d05h: %MODEM-5-DL_GOOD: Modem (1/4) completed firmware download:
2d05h: %MODEM-5-DL_GOOD: Modem (1/5) completed firmware download:
Step 6
Verify that the new firmware was successfully mapped to the modems.
In the following example:

SPE 1/0 applies to modems 1/0 through 1/5.

SPE 1/1 applies to modem 1/6 through 1/11, and so on.

The MICA modules 0 through 7 in slot 1 are running version 2.7.1.0 (not 2.6.2.0).

All the modems in slot 2 are still running version 2.6.2.0, which is bundled into the Cisco IOS
image (see the field IOS-Default).
5300-NAS#show modem map
Slot 1 has Mica Carrier card.
Modem Firmware Firmware
Module Numbers Rev Filename
0 1/0 - 1/5 2.7.1.0 flash:mica-modem-pw.2.7.1.0.bin
1 1/6 - 1/11 2.7.1.0 flash:mica-modem-pw.2.7.1.0.bin
2 1/12 - 1/17 2.7.1.0 flash:mica-modem-pw.2.7.1.0.bin
3 1/18 - 1/23 2.7.1.0 flash:mica-modem-pw.2.7.1.0.bin
4 1/24 - 1/29 2.7.1.0 flash:mica-modem-pw.2.7.1.0.bin
5 1/30 - 1/35 2.7.1.0 flash:mica-modem-pw.2.7.1.0.bin
6 1/36 - 1/41 2.7.1.0 flash:mica-modem-pw.2.7.1.0.bin
7 1/42 - 1/47 2.7.1.0 flash:mica-modem-pw.2.7.1.0.bin