Specifications

6-8
Cisco AS5x00 Case Study for Basic IP Modem Services
11/24/1999
Section 6 Modem Management Operations
Managing Modem Firmware
Depending on which Cisco IOS Release is loaded in the NAS, there are two commands that you can
use. Table 6-3 describes these two commands.
The following MICA example uses the
spe
command. The numbers 1/0 1/7 refer to modem
module
numbers
0 through 7 in slot 1. These numbers do not refer to specific
modem numbers
(for example,
slot/port for Microcom modems). In this example, 48 modems are upgraded (8 SPE x 6 modems per
module = 48 modems).
5300-NAS#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
5300-NAS(config)#spe 1/0 1/7
5300-NAS(config-spe)#firmware location flash:mica-modem-pw.2.7.1.0.bin
5300-NAS(config-spe)#
*Jan 23 11:14:48.702: %MODEM-5-DL_START: Modem (1/0) started firmware download
*Jan 23 11:14:48.702: %MODEM-5-DL_START: Modem (1/1) started firmware download
*Jan 23 11:14:48.702: %MODEM-5-DL_START: Modem (1/2) started firmware download
*Jan 23 11:14:48.702: %MODEM-5-DL_START: Modem (1/3) started firmware download
*Jan 23 11:14:48.702: %MODEM-5-DL_START: Modem (1/4) started firmware download
*Jan 23 11:14:48.702: %MODEM-5-DL_START: Modem (1/5) started firmware download
*Jan 23 11:15:03.042: %MODEM-5-DL_GOOD: Modem (1/0) completed firmware download:
*Jan 23 11:15:03.042: %MODEM-5-DL_GOOD: Modem (1/1) completed firmware download:
*Jan 23 11:15:03.042: %MODEM-5-DL_GOOD: Modem (1/2) completed firmware download:
*Jan 23 11:15:03.042: %MODEM-5-DL_GOOD: Modem (1/3) completed firmware download:
*Jan 23 11:15:03.042: %MODEM-5-DL_GOOD: Modem (1/4) completed firmware download:
*Jan 23 11:15:03.042: %MODEM-5-DL_GOOD: Modem (1/5) completed firmware download:
*Jan 23 11:15:03.046: %MODEM-5-DL_START: Modem (1/6) started firmware download
*Jan 23 11:15:03.046: %MODEM-5-DL_START: Modem (1/7) started firmware download
*Jan 23 11:15:03.046: %MODEM-5-DL_START: Modem (1/8) started firmware download
*Jan 23 11:15:03.050: %MODEM-5-DL_START: Modem (1/9) started firmware download
*Jan 23 11:15:03.050: %MODEM-5-DL_START: Modem (1/10) started firmware download
*Jan 23 11:15:03.050: %MODEM-5-DL_START: Modem (1/11) started firmware download
*Jan 23 11:15:17.394: %MODEM-5-DL_GOOD: Modem (1/6) completed firmware download:
*Jan 23 11:15:17.394: %MODEM-5-DL_GOOD: Modem (1/7) completed firmware download:
*Jan 23 11:15:17.394: %MODEM-5-DL_GOOD: Modem (1/8) completed firmware download:
*Jan 23 11:15:17.394: %MODEM-5-DL_GOOD: Modem (1/9) completed firmware download:
*Jan 23 11:15:17.394: %MODEM-5-DL_GOOD: Modem (1/10) completed firmware download
*Jan 23 11:15:17.394: %MODEM-5-DL_GOOD: Modem (1/11) completed firmware download
.
.
.
*Jan 23 11:16:43.482: %MODEM-5-DL_GOOD: Modem (1/47) completed firmware download
Table 6-3 Modem Mapping Commands
Cisco IOS Command Notes
12.0(5)T and later
spe
An SPE unit is defined as the smallest software
downloadable unit. For Microcom, an SPE is an
individual modem.
For MICA, an SPE is either 6 or 12 modems, depending
on whether the MICA module is single or double
density.
Before Release
12.0(5)T
copy source modem
Replace the variable
source
with the keyword
flash
or
bootflash
.