Installation guide

7-58
Network Processing Engine and Network Services Engine Installation and Configuration
OL-4448-08
Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information
Using show Commands to Check the Installation
port number (slot/port). The chassis slot number for the I/O controller is always slot 0. Table 7-1 lists
the NPE-G1, NPE-G2, the I/O controller models, their corresponding interfaces, and the interface
addressing syntax for each interface.
The remainder of this section provides examples of show commands that pertain to the NPE-G1 and
NPE-G2. The output from the show commands is from the NPE-G1 or the NPE-G2.
To determine the hardware configuration of your NPE-G1 or NPE-G2, use the show version command.
The following example shows an NPE-G2 installed in a Cisco 7206VXR router:
Router# show version
Cisco IOS Software, 7200 Software (C7200-JS-M), Version 12.4(PC_D.051028) UBUILDIT Image,
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Fri 28-Oct-05 00:30 by biff
(display text omitted)
Cisco 7206VXR (NPE-G2) processor (revision A) with 917504K/131072K bytes of memory.
Processor board ID 32428149
MPC7448 CPU at 1660Mhz, Implementation 0, Rev 2.0
6 slot VXR midplane, Version 2.8
(display text omitted)
Table 7-1 Identifying Interface Addresses on the NPE-G1, NPE-G2, and Various I/O Controllers
Model Interface Numbers Syntax
NPE-G1 and NPE-G2 Gigabit Ethernet (port 0/1)
1
Gigabit Ethernet (port 0/2)
Gigabit Ethernet (port 0/3)
1. Both optical and copper ports report the same syntax. For example, Gigabit Ethernet RJ-45 port 0/2 reports GigabitEthernet 0/2, as does Gigabit Ethernet
GBIC port 0/2. You can use only one port per interface, depending on the port selected using the media-type command.
Chassis slot—always 0
Interface port—1, 2, or 3
GigabitEthernet 0/1
GigabitEthernet 0/2
GigabitEthernet 0/3
C7200-I/O-GE+E Gigabit Ethernet (port GE 0) Chassis slot—always 0
Interface port—0
gigabitethernet 0/0
Ethernet (port E 0) Chassis slot—always 0
Interface port—0
fastethernet 0/0
C7200-I/O-2FE/E Fast Ethernet/Ethernet (port 0) Chassis slot—always 0
Interface port—0
fastethernet 0/0
Fast Ethernet/Ethernet (port 1) Chassis slot—always 0
Interface port—1
fastethernet 0/1
C7200-I/O-FE
2
2. The Product Number C7200-I/O-FE does not specify MII because both an MII and an RJ-45 receptacle are included.
Fast Ethernet (MII or RJ-45) Chassis slot—always 0
Interface port—0
fastethernet 0/0
C7200-I/O No interface ports — —
C7200-I/O-FE-MII
3
3. The I/O controller with the Product Number C7200-I/O-FE-MII has a single MII Fast Ethernet receptacle only. Although still supported by
Cisco Systems, this I/O controller with a single MII receptacle is no longer an orderable product as of May 1998.
Fast Ethernet (MII) Chassis slot—always 0
Interface port—0
fastethernet0/0