Specifications

A-38
Cisco MGX 8800/8900 Series Software Configuration Guide
Release 5.1, Part Number OL-6482-01, Rev. A0, January 25, 2005
Appendix A Downloading and Installing Software Upgrades
Upgrade Procedures for RPM-PR and RPM-XF Cards
0 -rw- 2490064 May 11 2004 15:37:14 +00:00 frsm12_005.000.004.034-A.fw
0 -rw- 3674368 May 11 2004 15:36:54 +00:00 axsmxg_005.000.004.034-P1.fw
0 -rw- 838840 May 11 2004 15:36:46 +00:00 axsmxg_005.000.004.034-A_bt.fw
0 -rw- 742168 May 11 2004 15:36:44 +00:00 axsme_005.000.004.034-A_bt.fw
0 -rw- 297988 May 11 2004 15:46:40 +00:00 frsm_8t1e1_FR8_BT_1.0.02.fw
0 -rw- 264592 May 11 2004 15:46:26 +00:00 cesm_8t1e1_CE8_BT_1.0.02.fw
0 -rw- 3111904 May 11 2004 15:36:38 +00:00 axsme_005.000.004.034-A.fw
0 -rw- 744600 May 11 2004 15:36:32 +00:00 axsm_005.000.004.034-A_bt.fw
0 -rw- 3267520 May 11 2004 15:36:22 +00:00 axsm_005.000.004.034-A.fw
0 -rw- 248686 May 11 2004 15:32:56 +00:00 vism_8t1e1_VI8_BT_3.2.00.fw
0 -rw- 4135448 May 11 2004 15:32:52 +00:00 vism_8t1e1_003.053.103.007-I.fw
0 -rw- 4135000 May 11 2004 15:32:42 +00:00 vism_8t1e1_003.003.103.007-I.fw
838616064 bytes total (721004544 bytes free)
Step 6 To display the files in the bootflash, enter the show flash: command.
Router#show flash:
-#- ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name
1 .. image F596869A 296D88 27 2452744 Feb 28 2001 03:16:05 rpm-boot-mz_122-4.T
30315128 bytes available (2452872 bytes used)
Step 7 To copy new boot software to the bootflash, enter the copy command.
Router#copy x:rpm-boot-mz_002.001.000.000 bootflash:
Destination filename [rpm-boot-mz_002.001.000.000]?
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
CCCCCCCCCCCCCCCCCCCC
2334044 bytes copied in 35.768 secs (66686 bytes/sec)
Tip When prompted for the destination filename, press enter to use the source filename shown in
the prompt. To change the destination filename, type a new filename after the prompt.
Step 8 To verify that the file was copied, enter the show flash: command.
Step 9 To set the BOOTLDR variable to specify the new boot software, complete the following steps:
a. Enter the router global configuration mode
Router#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
b. Set the BOOTLDR variable to the new boot image to be loaded
Router(config)#boot bootldr bootflash:rpm-boot-mz_002.001.000.000
c. Exit global configuration mode and save the new configuration.
Router(config)#^Z
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
d. Verify that the BOOTLDR variable is set
RPM-XF#show bootvar
BOOT variable = bootflash:rpmxf-......
CONFIG_FILE variable =
BOOTLDR variable = bootflash:rpm-boot-mz_002.001.000.000
Configuration register is 0x2