Specifications

3-85
Cisco MGX 8800/8900 Series Software Configuration Guide
Release 5.1, Part Number OL-6482-01, Rev. A0, January 25, 2005
Chapter 3 Provisioning PXM1E Communication Links
General PXM1E Configuration Procedures
The following example shows what appears when you enter the dspcons command without parameters.
PXM1E_SJ.8.PXM.a > dspcons
Local Port Vpi.Vci Remote Port Vpi.Vci State Owner Pri Persistency
----------------------+------------------------+---------+-------+---+-----------
4.1 4 35 Routed 26 35 OK MASTER 8 Persistent
Local Addr: 47.00918100000000001a533377.000001072301.00
Remote Addr: 47.009181000000000164444b61.00000107d301.00
Preferred Route ID:- Cast Type: P2P
4.2 4 36 Routed 26 36 OK SLAVE - Persistent
Local Addr: 47.00918100000000001a533377.000001072302.00
Remote Addr: 47.009181000000000164444b61.00000107d302.00
Preferred Route ID:- Cast Type: P2P
11.1 11 119 11.5 11 120 OK SLAVE - Persistent
Local Addr: 47.00918100000000001a533377.000001075b01.00
Remote Addr: 47.00918100000000001a533377.000001075b05.00
Preferred Route ID:- Cast Type: P2P
11.5 11 120 11.1 11 119 OK MASTER 8 Persistent
Local Addr: 47.00918100000000001a533377.000001075b05.00
Remote Addr: 47.00918100000000001a533377.000001075b01.00
Preferred Route ID:- Cast Type: P2P
7:2.11:11 100 100 Routed 0 0 OK MASTER 8 Persistent
Local Addr: 47.00918100000000001a533377.000001073b0b.00
Remote Addr: 00.000000000000000000000000.000000000000.00
Preferred Route ID:- Cast Type: P2MP
7:2.11:11 125 125 7:2.12:12 135 135 OK SLAVE - Persistent
Local Addr: 47.00918100000000001a533377.000001073b0b.00
Remote Addr: 47.00918100000000001a533377.000001073b0c.00
Preferred Route ID:- Cast Type: P2P
7:2.12:12 135 135 7:2.11:11 125 125 OK MASTER 8 Persistent
Local Addr: 47.00918100000000001a533377.000001073b0c.00
Remote Addr: 47.00918100000000001a533377.000001073b0b.00
Preferred Route ID:- Cast Type: P2P
Displaying the Status of a Single Connection
To display the configuration and status of a single connection, enter the dspcon command as follows:
PXM1E_SJ.8.PXM.a > dspcon <portid> <vpi> <vci>
The portid, vpi, and vci parameters uniquely identify the connection you want to display. These
parameters can be found for all connections in the dspcons command display. The following example
shows the data displayed for a single connection.
M8850_NY.7.PXM.a > dspcon 6:1.8:18 100 100
Port Vpi Vci Owner State Persistency
----------------------------------------------------------------------------
Local 6:1.8:18 100.100 MASTER OK Persistent
Address: 47.00918100000000036b5e31b3.000001061812.00
Node name: M8850_NY
Remote Routed 100.100 SLAVE -- Persistent
Address: 47.00918100000000036b5e2bb2.00000106180d.00
Node name: M8850_LA
-------------------- Provisioning Parameters --------------------
Connection Type: VCC Cast Type: Point-to-Point
Service Category: nrt-VBR Conformance: nrt-VBR.1
Bearer Class: BCOB-X
Last Fail Cause: No Fail Attempts: 0
Continuity Check: Disabled Frame Discard: Disabled
L-Utils: 100 R-Utils: 100 Max Cost: -1 Routing Cost: 30240 (AW)