Specifications

xxvi
Cisco MGX 8850 (PXM45) and MGX 8950 Software Configuration Guide
Release 3, Part Number 78-14788-01 Rev. C0, January 2004
About This Guide
Related Documentation
Cisco MGX 8950 Multiservice Service Release 3
The product documentation for the installation and operation of the Cisco MGX 8950 Release 3 switch
is listed in Table 5.
SES PNNI Release 3
The product documentation for the understanding, the installation, and the operation of the Service
Expansion Shelf (SES) Private Network-to-Network Interface (PNNI) Controller is listed in Table 6.
Table 5 Cisco MGX 8950 Switch Release 3 Documentation
Title Description
Cisco MGX 8950 Hardware Installation Guide,
Release 3
DOC-7814147=
Describes how to install the Cisco MGX 8950 core switch. This
documentation explains what the switch does and covers site
preparation, grounding, safety, card installation, and cabling. The
Cisco MGX 8950 switch uses a PXM45/B controller card and
provides support for broadband service modules.
Cisco MGX 8830, MGX 8850 (PXM45 and PXM1E),
and MGX 8950 Command Reference, Release 3
DOC-7814789=
Describes the PXM commands that are available on the CLI of the
Cisco MGX 8830, Cisco MGX 8850, and Cisco MGX 8950 switches.
Cisco MGX 8850 (PXM45) and MGX 8950 Software
Configuration Guide, Release 3
DOC-7814788=
Describes how to configure the Cisco MGX 8850 (PXM45) and the
Cisco MGX 8950 switches with a PXM45 controller to operate as
ATM edge or core switches. This guide also provides some operation
and maintenance procedures.
Cisco AXSM Software Configuration Guide and
Command Reference for MGX 8850 (PXM45) and
MGX 8950, Release 3
DOC-7814257=
This guide explains how to configure the AXSM cards for operation
and a command reference that describes the AXSM commands in
detail. The AXSM cards covered in this manual are the AXSM/A,
AXSM/B, AXSM-E, and AXSM-32-T1E1-E.
Cisco SNMP Reference for MGX 8850 (PXM45 and
PXM1E), MGX 8950, and MGX 8830, Release 3
DOC-7814747=
Provides information on all supported MIB objects, support
restrictions, and traps for AXSM, AXSM-E, SRM-3T3, SRME,
FRSM12, PXM45, PXM1E, RPM-PR, and RPM-XF.
Cisco MGX and SES PNNI Network Planning Guide
DOC-7813543=
Provides guidelines for planning a PNNI network that uses the Cisco
MGX 8850 (PXM45 and PXM1E), Cisco MGX 8950, and the Cisco
BPX 8600 switches. When connected to a PNNI network, each Cisco
BPX 8600 series switch requires an SES for PNNI route processing.
Cisco MGX Route Processor Module (RPM-XF)
Installation and Configuration Guide, Release 3
OL-2768-01 (online only)
Describes how to install and configure the Cisco MGX Route
Processor Module (RPM-XF) in the Cisco MGX 8850 Release 3
switch. Also provides site preparation, troubleshooting, maintenance,
cable and connector specifications, and basic Cisco IOS configuration
information.
Regulatory Compliance and Safety Information for
the Cisco MGX 8830, MGX 8850 (PXM45 and
PXM1E), and MGX 8950 Switches
DOC-7814790=
Provides regulatory compliance, product warnings, and safety
recommendations for the Cisco MGX 8830, Cisco MGX 8850
(PXM45 and PXM1E), and Cisco MGX 8950 switches.