Cisco MGX 8260 Command Line Interface Guide Software Release 1.2 September 2000 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
C O N T E N T S About This Guide xvii Document Overview xvii Who Should Use This Guide Conventions xvii xviii Obtaining Documentation World Wide Web xviii xviii Documentation CD-ROM xviii Ordering Documentation xviii Obtaining Technical Assistance Cisco Connection Online xix xix Technical Assistance Center Documentation Feedback CHAPTER 1 xix xx Overview of the MGX 8260 Media Gateway Features and Benefits 1-1 Managing the MGX 8260 Media Gateway WebViewer Management Interface SNMP Mana
Contents Assigning a tftp Security Key Configuring Node Parameters 2-6 2-6 Viewing Node Parameters 2-6 Setting Node Parameters 2-7 Changing the Interface Line Type 2-7 Changing the Gateway Control Protocol Configuring the Management Interfaces 2-7 2-8 Viewing Management Port Parameters 2-8 Configuring the 10BaseT Management Port Configuring In-Band Management Paths Configuring IP Routes 2-10 2-11 Deleting IP Routes 2-12 Synchronizing the System Clock 2-12 Setting Clock Parameters 2-12
Contents Adding NSC Redundancy 3-16 Adding BSC Redundancy 3-17 Deleting Redundancy 3-17 Invoking a Switchback 3-18 Saving and Restoring Card Configurations Backing Up Configurations 3-18 3-18 Uploading Configurations 3-19 Downloading Configurations Restoring Configurations 3-19 3-20 Upgrading Software Images 3-21 System Software Upgrade Paths Security Key Requirements Installation Procedures 3-21 3-21 3-21 Downloading Software from CCO 3-21 Transferring Files to the MGX 8260 Upgradi
Contents Adding DS3 Lines 4-10 Changing DS3 Lines 4-10 Deleting DS3 Lines Mapping DMC Lines 4-11 4-11 Adding Map Table Entries Changing Map Tables 4-12 4-13 Deleting Map Table Entries Viewing Map Tables 4-13 4-13 Configuring Fast Ethernet Lines 4-14 Viewing Fast Ethernet Configuration and Status Adding a Fast Ethernet Line 4-14 4-15 Changing a Fast Ethernet Line Deleting Fast Ethernet Lines 4-16 4-16 Setting the Fast Ethernet Administrative Status Configuring Static Routes 4-17 Adding
Contents Viewing Calls by Transaction 4-31 About the Announcement Service 4-31 File Encoding File Types File Names 4-31 4-32 4-32 Configuration Tasks for Announcement Services Adding and Activating an Announcement 4-32 4-32 Deactivating and Removing an Announcement Viewing Announcement Files CHAPTER 5 Call Control 4-33 4-33 5-1 Primary Call Control Components 5-1 Primary MGX 8260 Call Control Interfaces Understanding MGCP 5-1 5-2 Configuration Tasks for MGCP 5-3 Switching from IPDC t
Contents Adding a Session 5-16 Deleting a Session 5-16 Viewing Session Statistics 5-16 Viewing Session Group Statistics 5-16 Viewing RUDP Connection Statistics Viewing RUDP Transport Statistics Viewing Session Statistics Managing ISDN D Channels 5-18 Managing MACSAP Profiles 5-19 5-20 Adding MACSAP Profiles 5-20 Deleting MACSAP Profiles 5-20 Viewing MACSAP Profiles 5-20 Viewing MACSAP Statistics Managing DLSAP Profiles 5-21 5-22 Adding DLSAP Profiles 5-22 Deleting DLSAP Profiles 5-2
Contents Viewing IPDC Timer and Retry Counter Information Viewing IPDC COT Information CHAPTER 6 Alarm Surveillance 5-35 5-36 6-1 Surveillance Tasks for Alarms 6-1 Monitoring Shelf Alarms 6-2 Monitoring Card Alarms 6-4 Viewing Card Alarms Monitoring DS1 Alarms 6-4 6-5 Viewing DS1/E1 Alarms 6-5 Viewing DS1 Alarm Thresholds 6-6 Setting DS1 Alarm Thresholds Monitoring E1 Alarms 6-7 6-8 Viewing E1 Alarms 6-8 Viewing E1 Performance Alarms Viewing E1 Alarm Thresholds Setting E1 Alarm Thre
Contents Listing Email Server and Email Alert Registrations Configuring SNMP Trap Managers 6-28 Registering SNMP Trap Managers Changing SNMP Trap Registrations Viewing SNMP Trap Registrations 6-30 6-30 6-30 Understanding Trap Numbers Shelf Traps 6-31 Card Traps 6-32 DS1 Traps 6-32 DS3 Traps 6-33 SONET Traps Voice Port Events ISDN Traps 6-31 6-34 Fast Ethernet Traps 6-34 6-35 6-35 MGCP Traps 6-35 Backhaul Traps 7 6-29 6-29 Viewing Chronological Traps CHAPTER 6-28 Deleting SNMP Tra
Contents Viewing Interval DS3 Statistics 7-13 Viewing DS3 Real-Time Alarm Statistics Clearing Real-Time Statistics Monitoring SONET Performance 7-13 7-13 7-13 Monitoring SONET Section Statistics 7-14 Viewing Section Current Statistics 7-14 Clearing Section Current Statistics 7-14 Viewing Section Total Statistics 7-15 Clearing Section Total Statistics 7-15 Viewing Section Interval Statistics Monitoring SONET Line Statistics 7-15 7-17 Viewing Line Current Statistics 7-17 Clearing Line Cur
Contents Clearing Fast Ethernet Alarms Clearing SONET Alarms 8-9 Clearing Environmental Alarms CHAPTER 9 Command Reference Command Syntax 9-1 9-1 Optional Parameters 9-1 9-1 Understanding Bitmaps Using Online Help 8-11 9-1 Command Line Interface Guidelines Security Levels 8-9 9-2 9-3 Command Syntax Help Command Summary Help 9-3 9-3 INDEX Cisco MGX 8260 Command Line Interface Guide xii Release 1.2, Part Number 78-10987-01 Rev.
F I G U R E S Figure 1-1 MGX 8260 Management Architecture Figure 1-2 Front Panel Indicators Figure 2-1 10BaseT Management Connections Figure 3-1 NSC Interface Modes Figure 3-2 Normal Operation with 1:2 NSC Redundancy Figure 3-3 Switchover with 1:2 NSC Redundancy Figure 3-4 Normal Operation with 1:1 BSC Redundancy Figure 3-5 Switchover with 1:1 BSC Redundancy Figure 4-1 Example of DS3 to DS1 Mapping from DMC to NSC Figure 4-2 Multi-chassis Timing 4-18 Figure 5-1 MGCP Protocol Stack 5-
Figures Cisco MGX 8260 Command Line Interface Guide xiv Release 1.2, Part Number 78-10987-01 Rev.
T A B L E S Table 1-1 System Indicators Table 1-2 Trunk Group Indicators Table 1-3 Card and Line Indicators Table 2-1 User Accounts and Access Privileges Table 3-1 Response of Reset Command by Card and State Table 3-2 Response for the Switch Card Command by Card and State Table 4-1 DMC Map Table Table 4-2 DMC Map Table for the addm13 Command Table 4-3 DMC Map Table for the Modified addm13 Command Table 6-1 DS1 Performance Alarm Thresholds Table 6-2 E1 Performance Alarm Thresholds Tabl
Tables Table 9-3 Valid Bitmaps for Service State Table 9-4 Time Zones 9-2 9-130 Cisco MGX 8260 Command Line Interface Guide xvi Release 1.2, Part Number 78-10987-01 Rev.
About This Guide This chapter describes the procedures for configuring, operating, and troubleshooting the MGX 8260 Media Gateway from the command line interface. Document Overview This guide contains instructions for configuring, operating, and troubleshooting the MGX 8260 Media Gateway.
About This Guide Conventions Conventions This guide uses the following conventions: Warning Means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, you must be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Caution Means be careful. In this situation, you might do something that could result in equipment damage or loss of data. Note Means take note.
About This Guide Obtaining Technical Assistance Nonregistered CCO users can order documentation through a local account representative by calling Cisco’s corporate headquarters (California, USA) at 408 526-4000 or, in North America, call 800 553-NETS (6387). Obtaining Technical Assistance Cisco provides Cisco Connection Online (CCO) as a starting point for all technical assistance. Warranty or maintenance contract customers can use the Technical Assistance Center.
About This Guide Obtaining Technical Assistance To contact by e-mail, use one of the following: Language E-mail Address English tac@cisco.com Hanzi (Chinese) chinese-tac@cisco.com Kanji (Japanese) japan-tac@cisco.com Hangul (Korean) korea-tac@cisco.com Spanish tac@cisco.com Thai thai-tac@cisco.com In North America, TAC can be reached at 800 553-2447 or 408 526-7209. For other telephone numbers and TAC e-mail addresses worldwide, consult the following web site: http://www.cisco.
C H A P T E R 1 Overview of the MGX 8260 Media Gateway The MGX 8260 Media Gateway is a full-scale, carrier-grade platform with high-performance, high-density termination and switching of voice, and data traffic over circuit or packet based WANs. With a modular architecture and interfaces that are compatible with a wide range of access and backbone network types, the MGX 8260 Media Gateway accommodates a diverse and changing communications network.
Chapter 1 Overview of the MGX 8260 Media Gateway Managing the MGX 8260 Media Gateway interchangeable switch fabrics. At the same time, ensure the lowest possible network delay. The MGX 8260 limits delay to 40 milliseconds (between two MGX 8260 gateways) for VoIP packetization/ de-packetization. • Maximize Service Availability The MGX 8260 provides the industry's highest availability—99.999 percent—to ensure that your customers enjoy always-on service.
Chapter 1 Overview of the MGX 8260 Media Gateway Managing the MGX 8260 Media Gateway Figure 1-1 MGX 8260 Management Architecture NMS (HPOV) WebViewer SNMP manager HTTP client Telnet or console MGX 8260 SNMP agent Web HTTP server CLI SCC database SNMP access functions NSC database DMC database BSC database 31937 MRPC WebViewer Management Interface The WebViewer controls and monitors all MGX 8260 parameters, and typically performs the following operations: • Configuration • Alarm managem
Chapter 1 Overview of the MGX 8260 Media Gateway Front Panel Controls and Indicators Command Line Interface All MGX 8260 functions and features are available at the command line interface. During initial system configuration you can only use the command line interface via the console port. Some configuration tasks can only be performed from the command line interface. Front Panel Controls and Indicators The MGX Media Gateway has four types of cards, with the following indicator groups (see Figure 1-2).
Chapter 1 Overview of the MGX 8260 Media Gateway Front Panel Controls and Indicators System Indicators The SCC has the system indicators.
Chapter 1 Overview of the MGX 8260 Media Gateway Front Panel Controls and Indicators Card and Line Indicators The NSC, BSC, and DMC line cards have the following indicators: Table 1-3 Card and Line Indicators LED Card or Line Indication Status CARD SCC green card active yellow standby (protection mode) flashing yellow file download red card failure flashing red card boot or mismatch green card active yellow standby (protection mode) red card fail green normal operation flashing
C H A P T E R 2 System Management System management commands configure the parameters of an MGX 8260 node that define overall operation and interactions with other nodes and servers. Logging On Before you can configure the MGX 8260 Media Gateway, you must log on as a user with the privilege to change system parameters. You need SuperUser privileges to change most system-level settings. To log on, follow these steps: Step 1 Open a telnet session with the MGX 8260 Media Gateway.
Chapter 2 System Management Configuration Tasks for System Initialization Configuring System Security The MGX 8260 controls user access two ways: • User accounts and passwords • SNMP communities Configuring User Accounts The MGX 8260 Media Gateway enforces security with user accounts and access levels. Users must log onto the MGX 8260 Media Gateway before performing any task, and authenticated users can perform only those tasks permitted by their access level.
Chapter 2 System Management Configuration Tasks for System Initialization Adding User Profiles Only users with access level 1 can add new profiles to the MGX 8260 Media Gateway. To add a new user profile, follow these steps: Step 1 Log on to the MGX 8260 Media Gateway at access level 1. Step 2 Enter the addusp command, specifying the user ID and access level: The system adds a new user with a default password that matches the user id.
Chapter 2 System Management Configuration Tasks for System Initialization For example, the following command removes the user profile for William: delusp William Viewing Current Logins You can view summary or detail information for current logins. To view summary information about all active logins, use the lslogins command.
Chapter 2 System Management Configuration Tasks for System Initialization Viewing Community Strings To view a particular community string, enter the lscms command, specifying the community string index. The system displays the community string information: ======================================================================= Community String Entry (lscms) ======================================================================= Community String Index :1 Commumity String :Public Manager IP Address :0.0.0.
Chapter 2 System Management Configuration Tasks for System Initialization Assigning a tftp Security Key The tftp key authenticates file transfers between the MGX 8260 Media Gateway and a tftp client. If the key is not set, or if the key provided during the file transfer does not match this key, the file is not transferred. To set the security key, enter the chkey command, specifying the security key. The system records the security key. To view the security key, enter the lskey command.
Chapter 2 System Management Configuration Tasks for System Initialization To view the date and time, enter the lsdate command. The system displays the date, time, and time zone: ======================================================================= System Time and Date Information (lsdate) ======================================================================= Date : 03/21/1999 Time : 22:14:12 TimeZone : gmtplus12 Setting Node Parameters Normally, system-wide parameters are set during installation.
Chapter 2 System Management Configuration Tasks for System Initialization Configuring the Management Interfaces You configure the MGX 8260 management interface for local or remote operation by setting the appropriate IP addresses and management paths.
Chapter 2 System Management Configuration Tasks for System Initialization Figure 2-1 10BaseT Management Connections NMS stations MGX 8260 Management ports 1 and 2 31926 M IP network 10BaseT LAN Tips Change management IP address from the console port rather than a telnet session. To configure the 10BaseT management port, follow these steps: Step 1 Connect a VT100 terminal to the console port. Step 2 Log onto the MGX 8260 Media Gateway as a SuperUser.
Chapter 2 System Management Configuration Tasks for System Initialization To configure an in-band management path, follow these steps: Step 1 Contact your network administrator to obtain an IP address that is compatible with your in-band network. Step 2 Verify that the chassis is configured for Fast Ethernet lines. Step 3 Set the in-band management IP address, using the chibip command. For example, if you assigned a IP address of 10.15.28.
Chapter 2 System Management Configuration Tasks for System Initialization Displayed Information Description Destination The destination IP address. Gateway The gateway, or next hop, for the route. IF The interface identifier: 1—Primary Ethernet port 2—Secondary Ethernet port 3—In-band path Mask The subnet mask for the route. Type The type of route, such as direct or indirect Protocol The protocol type, such as local or other. Age The age of the route is seconds.
Chapter 2 System Management Configuration Tasks for System Initialization Deleting IP Routes To delete an IP route, follow these steps: Step 1 Type the deliproute command, specifying the destination address. Step 2 Verify the route deletion using the lsiproutes command.
Chapter 2 System Management Configuration Tasks for System Initialization Viewing Clock Parameters You view clock status with a single command. The clock parameters are: • Status of the primary and secondary clocks • The current clock source • The lowest stratum level of the current clock source To view clock status, enter the lsclksrcs command.
Chapter 2 System Management Configuration Tasks for System Initialization Displayed Information Description Clock Stratum The level of Stratum clock: Master Clock Current Clock • level 3 (reserved for future use) • level 4 The master clock source: • primary • secondary • internal The current clock source: • primary • secondary • internal Switching to the Secondary Clock You can force the system to switch between the primary and secondary clocks.
C H A P T E R 3 Card Management This chapter explains how to configure cards and lines for service delivery. Configuring Cards Card parameters control the operational characteristics of the card as a whole. The MGX 8260 Media Gateway supports the following cards: • SCC (System Controller Card) The SCC provides overall system control and database management for the shelf. In addition, the card provides optional broadband interfaces to the WAN backbone network, such as Fast Ethernet or SONET.
Chapter 3 Card Management Configuration Tasks for Cards Configuring Card Parameters This sections describes how to view and set card-level parameters. Viewing Card Configuration and Status To list information for a single card, enter the lscd command, specifying the card location by a slot number in the MGX 8260 chassis. Slots are numbered from 1 through 16, starting at the left. The system displays the card information.
Chapter 3 Card Management Configuration Tasks for Cards Displayed Information Description Back Card Type Daughter Card1 Type The back card type: • scc-4fe—Switch Control Card with four Fast Ethernet (100 Mbps) ports • scc4OC3—Switch Control Card with four OC-3 ports • scc4OC3MM—Switch Control Card with four mulit-mode OC-3 ports • bsc12T3—Broadband Service Card with 12 DS3 ports • dmcBsc6t3—Distribution Matrix Card or BSC with six DS3 ports • nsc-16t1e1—Narrowband Service Card with sixteen T1
Chapter 3 Card Management Configuration Tasks for Cards Displayed Information Description Failure Reason Reset Reason The reason of the last card failure, as follows: • hwMSMFailed—One or both MSMs failed • hwSarFailed—Sar failed • hwPCIAErrInt—PCI-A error interrupt • hwASXFailed—ASX failed • hwALBMFailed—ALM or ABM switch port failed • hwCubitFailed—Cubit failed • hwBusCycleTmOut—Bus cycle timeout • hwHardDrvFailed—Hard drive failed • hwMgmtEthFailed—Management Ethernet failed • hwD
Chapter 3 Card Management Configuration Tasks for Cards Displayed Information Description Mismatch Reason Integrated line alarm state Line performance alarm state EMM temperature alarm state EMM voltage alarm state SW error alarm state The reason the card was last reset, as follows: • shellReset • hardReboot • softRebootNoImage • softReboot • chipError • eventLogReset • taskError • softwareUpgrade • gracefulSwitchover • dmcRemovedSwitchover • sccBcRemovedSwitchover • appsInitF
Chapter 3 Card Management Configuration Tasks for Cards Displayed Information Description Component failure alarm state The state of the component alarm for the card: • No Alarm • Minor Alarm • Major Alarm ATM Queue Profile The queue profile for ATM traffic on the SCC. Valid profiles: 1 to 10.
Chapter 3 Card Management Configuration Tasks for Cards Viewing Summary Information for Cards To list summary information for all cards, enter the lscds command.
Chapter 3 Card Management Configuration Tasks for Cards The system lists current DSP information: ====================================================================== MultiService Module (DSP) Entries (lsdsps) ====================================================================== Slot Number DSP MSM Number DSP Number DSP Status =============== ================== ================ ================ 2 1 1 active 2 1 2 active 2 1 3 active 2 1 4 active 2 1 5 active 2 1 6 active 2 1 7 active 2 1 8 active Dis
Chapter 3 Card Management Configuration Tasks for Cards • No back card All sixteen T1 lines operate in the same mode. The system ignores this setting for cards other than the NSC.
Chapter 3 Card Management Configuration Tasks for Cards Back Plane Mode In the back plane mode, VoIP transmits and receives traffic from the DMC front card. The normal signal flow when using a DMC card is: DMC-BC -> DMC-FC -> Bus -> NSC-FC -> Bus -> SCC-FC -> SCC-BC where BC = Back Card and FC = Front Card Use the back plane mode when you use the NSC card in conjunction with a DMC card and DS3 lines.
Chapter 3 Card Management Configuration Tasks for Cards Resetting a Card The resetcd command restarts a card and restores its stored configuration. The following table shows response of the reset command for different card types and operating states: Table 3-1 Response of Reset Command by Card and State State SCC slots 9/10 DMC slots 7/8 active OK Service not available on DMC standby OK OK empty Card does not exist.
Chapter 3 Card Management Configuration Tasks for Cards Using 1:N NSC Redundancy A single secondary card can support multiple primary cards. In this configuration, a failure of any of the primary cards causes a switchover to the designated secondary. After a switchover, the other NSCs are unprotected until you fix the problem and restore the primary card to the active state.
Chapter 3 Card Management Configuration Tasks for Cards Figure 3-3 Switchover with 1:2 NSC Redundancy Primary card (active) Secondary card (active) Primary card (failed) NSC NSC NSC NSC NSC NSC DMC DMC SCC SCC FDX ACT FDX ACT 1 1 2 2 3 3 4 4 LINE ACT LINE ACT LAN 1 LAN 1 LAN 2 Failed LAN 2 ALMC ALMC ALMH ALMH CLR CLR ACO ACO DISK PWR A PWR B DSC DISK PWR A PWR B CARD CARD CARD CARD CARD CARD CARD CARD CARD CARD LINE LINE LINE LINE LINE LINE LINE LI
Chapter 3 Card Management Configuration Tasks for Cards For example, you can configure cards 15 and 16 for redundancy (see Figure 3-4).
Chapter 3 Card Management Configuration Tasks for Cards A failure of the active card causes a switchover to the backup card. During the switchover, the active and standby roles are reversed (see Figure 3-5). The card that failed reboots, and the Card LED changes to either yellow or red, depending on the type of problem. After a switchover, the other BSC is unprotected until you fix the problem and restore the primary card to the active state.
Chapter 3 Card Management Configuration Tasks for Cards The system displays all redundancy pairs: ======================================================================= Card Redundancy Table (lsreds) ======================================================================= Primary Slot Secondary Slot =============== ================ 1 3 5 3 Displayed Information Description Primary Slot The physical slot for the primary card of the redundancy pair Secondary Slot The physical slot for the secondary car
Chapter 3 Card Management Configuration Tasks for Cards Configuring NSC Redundancy with DMC To configure NSC redundancy with DMC, follow these steps: Step 1 Verify that at least one DMC and DS3 back card is installed in physical slot 7 or 8. Enter the following command to verify the hardware: lscds Step 2 Verify that the redundant NSC does not have a redundancy back card installed. See “Viewing Summary Information for Cards” section on page 3-7.
Chapter 3 Card Management Saving and Restoring Card Configurations Invoking a Switchback The switchover from primary to secondary cards is automatic when a primary card fails. Switching back is a manual task.
Chapter 3 Card Management Saving and Restoring Card Configurations Step 3 Record the file name for future reference. By default, the backup file name matches the software version name with a .cfg extension. For example, the backup file for software release R01.02.03 is SCC_R01.02.03.CFG Uploading Configurations The MGX 8260 stores configuration information for all cards in the chassis in the SCC hard drive. You can upload this configuration information to an external server for safekeeping.
Chapter 3 Card Management Saving and Restoring Card Configurations To restore a card configuration, follow these steps: Step 1 Log onto a workstation and locate the configuration file to download. Step 2 Initiate a tftp session with the target MGX 8260 Media Gateway using the tftp command. tftp Specify the IP address of the MGX 8260 management port in standard IP dot notation. Note Step 3 tftp is an operating system command executed by the management workstation.
Chapter 3 Card Management Upgrading Software Images For example: dbrstr scc_r01.02.03 Step 3 Restart the target card using the resetcd command. Upgrading Software Images This section describes the software upgrade paths, security key requirements, installation procedures, and database configurations needed for software upgrade. System Software Upgrade Paths Release 1.2.5 software supports graceful upgrades from the following releases: • 1.2.4 • 1.2.3 • 1.2.2 • 1.2.
Chapter 3 Card Management Upgrading Software Images To upgrade the MGX 8260, download the new system software from CCO to a management server on your network that supports the UNIX tftp function. Transferring Files to the MGX 8260 Using tftp, transfer the files to the MGX 8260 using the following procedure: Step 1 Log on to the workstation running the tftp server and locate the files you downloaded in the “Downloading Software from CCO” section.
Chapter 3 Card Management Upgrading Software Images 2. Log in as superuser or a user with level 1 privileges. 3. Follow the upgrade procedures for each card type. – See the “Upgrading SCC Software” section on page 3-23 for SCC upgrade procedures. – See the “Upgrading BSC Software” section on page 3-24 for BSC upgrade procedures. – See the “Upgrading NSC Software” section on page 3-26 for NSC upgrade procedures. 4. Note Log out of your Telnet session.
Chapter 3 Card Management Upgrading Software Images To upgrade SCC and software images, perform the following steps: Step 1 Upgrade the boot Flash software on each SCC using the following command. Issue the command for each SCC, replacing the with the appropriate number for your configuration. updatefls IMAGE/SCC/scc_r01.02.05.fls Step 2 Ensure that the standby SCC is in the standby state.
Chapter 3 Card Management Upgrading Software Images Warning Upgrading nonredundant cards interrupts service. Perform nonredundant upgrades during light traffic periods or during a prearranged maintenance window. If your MGX 8260 includes BSCs, perform the following steps to upgrade BSC Flash and software images: Step 1 Upgrade the boot Flash software on each BSC using the following command.
Chapter 3 Card Management Upgrading Software Images Step 8 Repeat Step 2 through Step 7 for additional BSC pairs in your system. Upgrading NSC Software The upgrade process for redundant NSCs is graceful. It does not interrupt established calls, but it can interrupt calls in the process of being established. When you invoke the process, the MGX 8260 upgrades and restarts the standby NSC. You can then commit or cancel the upgrade.
Chapter 3 Card Management Upgrading Software Images Step 6 Ensure that the previously standby NSC is now active and that the NSC in is now in standby state. Step 7 For an MGX 8260 configured for NSC redundancy, force a switchback to the NSC indicated in Step 3. Use the swcd command: swcd Where is the number of the standby/redundant NSC (currently in active state). Step 8 Note Repeat Step 3 through Step 7 for all NSCs in your system.
Chapter 3 Card Management Upgrading Software Images Cisco MGX 8260 Command Line Interface Guide 3-28 Release 1.2, Part Number 78-10987-01 Rev.
C H A P T E R 4 Service Management This chapter explains how to configure line and voice services. Configuration Tasks for Lines See the following sections for line configuration tasks.
Chapter 4 Service Management Configuration Tasks for Lines The system displays the common line entries: ===================================================================== Common Line Entries (lslns) ===================================================================== Line Number (Slot.Line) Line Type ================================= ================================== 2.1 dsx1-t1 11.1 dsx1-t1 11.2 dsx1-t1 11.
Chapter 4 Service Management Configuration Tasks for Lines Viewing Summary DS0 Information To list summary DS1 information for all lines, enter the lsds0s command.
Chapter 4 Service Management Configuration Tasks for Lines The system displays the following DS1/E1 details: ======================================================================= DS1 Line Entry (lsds1ln) ======================================================================= DS1 Line : 2.
Chapter 4 Service Management Configuration Tasks for Lines Displayed Information Description Line Coding The line coding format. Not applicable for T1 lines on BSCs.
Chapter 4 Service Management Configuration Tasks for Lines Displayed Information Description Line Loopback Config The loopback configuration of this interface. Transmit Clock Source • dsx1NoLoop • dsx1PayloadLoop • dsx1LineLoop • dsx1OtherLoop The clock source for the transmit signal. • loopTiming (reserved for future use) • localTiming • throughTiming (reserved for future use) Circuit Identifier The Cisco equipment circuit identifier, displayed as a text string.
Chapter 4 Service Management Configuration Tasks for Lines Adding DS1/E1 Lines This procedure explains how to add DS1/E1 lines to BSC or NSC cards. NSCs support either T1 or E1 lines, but the whole chassis must be configured for one mode or the other. DS1 channels within a DS3 line have the following mapping: Note DS 3 Line Number DS1 Line Number 501 1-28 502 29-56 503 57-84 504 85-112 505 113-140 506 141-168 Before adding DS1 lines to a DS3 line, ensure the corresponding DS3 line exists.
Chapter 4 Service Management Configuration Tasks for Lines Deleting DS1/E1 Lines Warning Deleting a DS1/E1 line interrupts service. Perform this operation during light traffic periods or in a pre-arranged maintenance window. To delete a DS1/E1 line, enter the delds1ln command, specifying the slot.line and number of lines. The system deactivates the DS1/E1 line and removes its configuration from the database. Note The MGX 8260 inhibits deletion of a line with an active connection.
Chapter 4 Service Management Configuration Tasks for Lines Displayed Information Description DS3 Line The slot and line number of the specified DS3 line Line Type The DS3 C-bit usage: • dsx3M23 • dsx3SYNTRAN (reserved for future use) • dsx3CbitParity (reserved for future use) Line Coding The line coding format, fixed at dsx3B3ZS.
Chapter 4 Service Management Configuration Tasks for Lines Viewing Summary DS3 Information To view summary information for all DS3 lines, enter the lsds3lns command. The system displays summary information for all DS3 lines: ======================================================================= DS3 Lines (lsds3lns) ======================================================================= Slot.Line Line Type Line Coding LED Status ========= ========== ============ ============= 16.
Chapter 4 Service Management Configuration Tasks for Lines For example, to activate a line loopback on DS3 line 501 in logical slot 11: chds3ln 11.501 # # # # 3 Deleting DS3 Lines To delete a DS3 line, enter the delds3ln command, specifying the logical number slot and line number (slot.line), and the number of lines to delete. Valid slot values: 7 or 8 for the DMC card; 11 -16 for the BSC card. Valid line values are 1-6. The system deactivates the DS3 line and removes its configuration from the database.
Chapter 4 Service Management Configuration Tasks for Lines A single DS3 can map to multiple NSCs or multiple DS3s can map to a single NSC. Map definitions can be organized or arbitrary, but often occur in contiguous groups because you can define a range of mappings with a single command.
Chapter 4 Service Management Configuration Tasks for Lines Table 4-2 DMC Map Table for the addm13 Command (continued) Source DS3 Line Source DS1 Line Destination NSC Slot Destination DS1 Line 1 4 1 2 1 5 1 3 Changing Map Tables You change map table entries one at a time. A change removes an existing mapping and replaces it with a map between the old source and new destination. To apply a change, the following must be true: • The command must specify an existing map pair.
Chapter 4 Service Management Configuration Tasks for Lines To view all DS3 to DS1 mappings, enter the lsm13s command.
Chapter 4 Service Management Configuration Tasks for Lines Displayed Information Description Operational Status The operational status for the line: Duplex Mode • active • inactive • failed • link down in active state • link down in inactive state The duplex mode for this line • full • half To view the information for all Fast Ethernet lines, enter the lsethlns command.
Chapter 4 Service Management Configuration Tasks for Lines The following example adds a Fast Ethernet line to slot 9 line 2 with an IP address of 10.15.26.98, a gateway of 10.15.26.1, a target state of active, RDP disabled, a subnet mask of 255.255.255.0, and full duplex mode: addethln 9.2 10.15.26.98 10.15.26.1 1 1 255.255.255.0 2 Step 2 Add other Fast Ethernet lines, as necessary. Step 3 Verify the configuration using the lsethlns command. The system displays the line configuration.
Chapter 4 Service Management Configuration Tasks for Lines Configuring Static Routes You can configure static routes for the MGX 8260 routing table. These routes apply to lines that utilize an IP network. You can configure static routes for empty slots or non-existing lines, but the changes have no effect without the necessary hardware. Adding Static Routes To add a static route, enter the addsrt command, as described in the “addsrt” section on page 9-30.
Chapter 4 Service Management Configuration Tasks for Lines Configuring OC-3 Lines The OC-3 SCC and back card supports four OC-3 lines. This section explains how to configure and manage these lines. Multi-chassis Considerations In a multi-chassis application, each MGX8260 needs a common reference clock for all TDM lines. You can accomplish this by synchronizing the clocks of each chassis to the common ATM switch clock (See Figure 4-2). Figure 4-2 Multi-chassis Timing MGX 8850 M OC-3 ...
Chapter 4 Service Management Configuration Tasks for Lines The system displays detail information for the SONET line: ======================================================================= Sonet Line Entry (lssonetln) ======================================================================= Sonet Line : 9.2 Medium Type : sonet Time Elapsed in Interval : 12 Line Valid Intervals : 0 Line Coding : sonetMediumNRZ Line Type : sonetMultiMode Circuit Identifier : PMC-PM5351-S/UNI-TETRA ver.
Chapter 4 Service Management Configuration Tasks for Lines Displayed Information Description Line Status(1) The line status, expressed as a bitmap: Bit 0: No defect present Bit 1: Section LOS (Loss of Signal) Bit 2: Section LOF (Loss of frame) Bit 3: Line AIS (Alarm Indication Signal) Bit 4: Line RDI (Remote Defect Indication) Bit 5: Path AIS Bit 6: Path LOP (Loss of Pointer) Bit 7: Path UEQ (idle) Bit 8: Path TIM (Trace Identifier Mismatch) Bit 9: Path SLM Bit 10: Path RDI Bit 11: Path ERDI server de
Chapter 4 Service Management Configuration Tasks for Lines Displayed Information Description Line Status(2) The LED status, expressed as a bitmap: Bit 0: Solid green Bit 1: Blinking green Bit 2: Solid yellow Bit 3: Blinking yellow Bit 4: Red Interface Type The type of interface, either OC3 or STM-1 Frame Type The type of framing, either STS-3c or STS-1 Loopback State The loopback state: • No loop • Line loop • Serial loop • Parallel loop HCS Masking The HCS masking state (reserved for fu
Chapter 4 Service Management Configuration Tasks for Lines Adding OC-3 Lines To add OC-3 lines, follow these steps: Step 1 Add one or more lines using the addsonetln command. Optionally, customize the line using the command line arguments. See the “addsonetln” section on page 9-28. The following example adds one line to slot 9 line 1 with default parameters: addsonetln 9.1 Step 2 Verify the configuration using the lssonetln command.
Chapter 4 Service Management Configuration Tasks for Lines The system displays detail E-RDI information for the line: ======================================================================= Sonet Line Entry (lssonetlnerdi) ======================================================================= Sonet Line : 9.1 Support Path ERDI : disable Transmitted Path Signal Label : 19 Expected Received Path Signal Label : 19 Received Path Signal Label : 0 Transmit PTID Length : 64 Transmit PTID Sync. pos.
Chapter 4 Service Management Configuration Tasks for Lines Displayed Information Description Expected Received PTID Length The expected trace identifier length for the SONET path: • 16 bytes (SDH only) • 64 bytes (SONET or SDH) Expected Received Ptid Sync. pos.
Chapter 4 Service Management Configuration Tasks for Lines Forming Hex Messages You use two hexidecimal numbers to represent each ASCII character in a trace message. For example, you represent an ASCII space with the hex pair 20. The following table shows a few additional examples. Trace Message Hex String 4 34 Hello World 48656c6c6f20576f726c64 For 16-byte msg, the maximum input string size is 32 hex characters.
Chapter 4 Service Management Configuration Tasks for Ports Configuring E-RDI and SONET Trace To change E-RDI parameters, follow these steps: Step 1 Change extended rdi parameters for SONET lines using the chsonetperdi command, specifying the location and E-RDI parameters. See the “chsonetperdi” section on page 9-123. Step 2 Change path trace parameters for SONET lines using the chsonettrace command, specifying the location and path trace parameters. See the “chsonettrace” section on page 9-125.
Chapter 4 Service Management Configuration Tasks for Ports Changing Voice Ports You can change any of the optional parameters for an existing port. To change a voice port, use the chvport command, specifying the same parameters as required to add a voice port. For example, to change the echo tail while leaving other parameters unchanged, type the following command: chvport 13 1 # # # # # 2 The system changes the echo tail for logical port 1 in slot 13 to tail24ms.
Chapter 4 Service Management Configuration Tasks for Ports Displayed Information Description Initial Dynamic Dejitter Size The initial length of the dejitter buffer, specified in multiples of 10 msec. Maximum Dynamic Dejitter Size The maximum length of the dejitter buffer, specified in multiples of 10 msec. Minimum Dynamic Dejitter Size The minimum length of the dejitter buffer, specified in multiples of 10 msec.
Chapter 4 Service Management Viewing Active Calls To view all ports, enter the lsports command.
Chapter 4 Service Management Viewing Active Calls Displayed Information Description TransactionID The transaction identifier for the active call. Only the backend platform software uses this number CallID An identifier for the active call. Source Slot number The slot number for the active call source. The slot, line, and DS0 numbers uniquely define a call while it is active. Source Line number The line number for the active call source. Source Ds0 The DS0 number for the active call source.
Chapter 4 Service Management About the Announcement Service Viewing Calls by Transaction To view call information for a specific transaction, enter the lsact command.
Chapter 4 Service Management Configuration Tasks for Announcement Services File Types The MGX 8260 Media Gateway supports the following file types: • .au • .wav File Names The Announcement Service uses a file identifier that it learns from the name you assign. Construct the file name as follows: fileName_ID.ext The file name is the alphanumeric string before the underscore and the file identifier is the number after the underscore.
Chapter 4 Service Management Configuration Tasks for Announcement Services Deactivating and Removing an Announcement To deactivate and remove an announcement, follow this procedure. Step 1 Deactivate the file using the deacannfile command, specifying the file ID. You can view file IDs using the lsannfiles command. Step 2 Optionally, remove the file using the rmannfile command, specifying the file ID. Since the system has limited file capacity, you should remove announcements you no longer plan to use.
Chapter 4 Service Management Configuration Tasks for Announcement Services To view resource usage for announcement files, use the lsdurationif command. The system displays the following information: =================================================== Duration Information of Ann.
C H A P T E R 5 Call Control The MGX 8260 Media Gateway works in conjunction with Media Gateway Controller (MGC) servers and the Public Switched Telephone Network (PSTN) to control voice and data calls. Primary Call Control Components The following components of the call control system are most important: • Signal Transfer Point (STP) STPs are components in the Signalling System 7 (SS7) network that route management traffic between Service Switching Points (SSPs) and Service Control Points (SCPs).
Chapter 5 Call Control Understanding MGCP • Media Gateway Control Protocol (MGCP) The MGX 8260 Media Gateway exchanges switching information with MGCs using either MGCP or IPDC over an IP network. The protocol choice depends on the specific network. The physical transport is Ethernet at the MGX 8260 interface. • IP Device Control (IPDC) The MGX 8260 Media Gateway exchanges switching information with MGCs using either MGCP or IPDC over an IP network. The protocol choice depends on the specific network.
Chapter 5 Call Control Configuration Tasks for MGCP Figure 5-2 MGCP Addresses and Ports Primary MGC Primary MGCP address/port 1 Secondary MGC Secondary MGCP address/port 1 Primary MGCP address/port 2 Secondary MGCP address/port 2 Net 1 Net 2 Local address 2 primary/secondary/ports 31940 Local address 1 primary/secondary/ports M The minimal system consists of a primary MGC network, the MGX 8260 Media Gateway, and an IP network.
Chapter 5 Call Control Configuration Tasks for MGCP Step 3 Verify the change using the lsndinf command. Configuring MGCP IP Addresses Before beginning this procedure, obtain the IP addresses and ports that apply to your system. Make sure your IP and port selections do not conflict with other equipment on the networks. Step 1 Set the local address and ports on network 1 using the chmgcplocaladdr1 command as described in the “chmgcplocaladdr1” section on page 9-97.
Chapter 5 Call Control Configuration Tasks for MGCP Viewing MGCP Settings You can view the following MGCP information: • IP addresses and connection status • Voice settings • Default call settings • MGCP status • Protocol statistics To view MGCP IP settings, use the lsmgcpdef command. The following information is displayed: ========================================================================= Primary MGCP Address 1 : 10.15.26.1 Primary MGCP UDP Port 1 : 2427 Primary MGCP Address 2 : 10.15.
Chapter 5 Call Control Configuration Tasks for MGCP Displayed Information Description Local Address 1 The IP address of the MGX 8260 interface for network 1. This address is on the same subnet as the Primary MGCP IP Address. Local Primary Port 1 The primary UDP port of the MGX 8260 interface for network 1. Local Address 2 The IP address of the MGX 8260 interface for network 2. This address is on the same subnet as the Primary MGCP IP Address.
Chapter 5 Call Control Configuration Tasks for MGCP Viewing Default Call Setup Parameters To view call control parameters, use the lsmpc command.
Chapter 5 Call Control Configuration Tasks for MGCP Displayed Information Description Default COT Transmit Tone The default transmit tone. For transponder COT, when the media gateway controller does not supply the tones, the default tone the gateway transmits is the default COT transmit tone.
Chapter 5 Call Control Configuration Tasks for MGCP Displayed Information Description Connectivity Timeout The time in milliseconds to wait for a request from MGCP before dropping the link. Response Timeout The time in milliseconds to wait before retransmitting unacknowledged messages.
Chapter 5 Call Control Understanding Sessions Understanding Sessions The session manager organizes individual sessions into groups and sets (see Figure 5-3). Organization of Sessions Set 6 Set 1 Group Group Session Session Session Session 46366 Figure 5-3 The backhaul sessions and groups include the following components: • Session—a connection between two points, defined by a local IP address and port and a remote IP address and port.
Chapter 5 Call Control Configuration Tasks for Sessions – Session 3 (MGX 8260 Net 2 to Active MGC Net 2) – Session 4 (MGX 8260 Net 2 to Standby MGC Net 2) This assumes that every transport address has corresponding IP interface address and a UDP port unique for that IP address. • • Two session groups: – Session group1 (session 1 and session 3) – Session group2 (session 2 and session 4) One session set containing session group 1 and group 2.
Chapter 5 Call Control Configuration Tasks for Sessions The system displays the following session set information: ======================================================================= Session Set (lsset) ======================================================================= Set Identifier : 1 Set State : outOfService Total Groups : 1 Active Group : -1 Minimum Slot Number : 11 Maximum Slot Number : 11 Minimum Line Number : 1 Maximum Line Number : 20 Redundancy Mode : nonFaultTolerant SwitchOver Failur
Chapter 5 Call Control Configuration Tasks for Sessions Adding a Session Set Session sets contain a collection of session groups and managers that control a range of MGX 8260 lines. One or two session sets are adequate for a single MGX 8260 chassis. To add a session set, use the addsset command. For example, the following command adds session set 1 for lines 1-168 of the BSC in slot 11: addsset 1 11 1 11 168 1 Deleting a Session To delete a session set, use the delsset command.
Chapter 5 Call Control Configuration Tasks for Sessions Displayed Information Description Group Previous Session The previously-active session within this group Total Sessions The total number of sessions for this group Total Active Sessions The total number of active sessions for this group To view all groups, use the lsgroups command.
Chapter 5 Call Control Configuration Tasks for Sessions The system displays the following session information: ======================================================================= Session Entry (lssession) ======================================================================= Session Identifier : 1 Group Id : 1 Session Set Id : 1 Session State : openWait Use State : outOfService Priority : 1 Local Port : 7007 Local Address : 10.15.38.233 Remote Port : 7007 Remote Address : 10.15.38.
Chapter 5 Call Control Configuration Tasks for Sessions To view all sessions, use the lssessions command.
Chapter 5 Call Control Configuration Tasks for Sessions The system displays the group statistics: ======================================================================= Session Group Statistics (lsgroupstat) ======================================================================= Set Identifier : 1 Group Identifier : 1 Session Failures : 0 Session Failover Success : 0 Active Packets Received : 0 Standby Packets Received : 0 Total PDU Post Errors : 0 Viewing RUDP Connection Statistics To view RUDP connect
Chapter 5 Call Control Managing ISDN D Channels The system displays the statistics: ======================================================================= RUDP Transport Statistics (lsrudptxstats) ======================================================================= Session Identifier : 1 Group Id : 1 Session Set Id : 1 RUDP Connections Opens : 0 RUDP Connection Resets : 978 RUDP Connection Refused : 0 RUDP Connection Failed : 0 RUDP Auto Resets : 0 RUDP Open Failed : 0 RUDP Not Ready : 0 RUDP Connect
Chapter 5 Call Control Managing ISDN D Channels Channel Bank D Channel to Media Gateway Controller DS3 BSC SCC Session MGC 31931 Figure 5-5 Each BSC contains 168 T1 lines, each a potential Primary Rate ISDN line. An ISDN line contains 24 channels, one of which is the D Channel that carries the signaling information for the other 23 channels. The BSC card can terminate a D Channel signaling stack and pass the payload to a Media Gateway Controller, via the SCC, using a backhaul session.
Chapter 5 Call Control Managing ISDN D Channels The following sections present detailed procedures for each of these steps. For more information on configuring backhaul, see the “Understanding Sessions” section on page 5-10. Managing MACSAP Profiles MACSAP management consists of adding and deleting profiles. You need at least one profile to add D Channels. Adding MACSAP Profiles To add a MACSAP profile, follow these steps: Step 1 Specify a MACSAP profile using the addmacsapprof command.
Chapter 5 Call Control Managing ISDN D Channels The system displays a single MACSAP profile: ======================================================================= MACSAP Profile (lsmacsapprof) ======================================================================= MACSAP Identifier : 1 MAC SAP Interface : network Link Setup Arbitration : passive LAPD Type : ccitt Maximum Outstanding Frames : 7 Timer Queue Upper Threshold : 1000 Timer Queue Lower Threshold : 100 Connection Timer : 500 T201 Timer : 1 T202
Chapter 5 Call Control Managing ISDN D Channels To view all MACSAP statistics, use the lsmacsapstats command. The system displays MACSAP statistic summaries: ======================================================================= MACSAP Statistics (lsmacsapstats) ======================================================================= Slot.Line Received Frames Transmitted Frames Received Bytes ========= =============== ================== ============== 14.
Chapter 5 Call Control Managing ISDN D Channels The system displays the specified DLSAP profile: ======================================================================= DLSAP Entry (lsdlsp) ======================================================================= DLSAP Profile Id : 1 Frame Length : 1960 Window Size : 7 Retransmission Count : 3 Congestion Timer : 200 t200 Timer : 1 t203 Timer : 10 Modulo : 128 TEI Assignment : 1 Maximum DLCs for this DLSAP : 1 TEI : 2 See the description of displayed inform
Chapter 5 Call Control Managing ISDN D Channels Displayed Information Description Number of Frames Dropped by MAC The number of frames dropped by the MAC Local Busy Status The local SAP busy state: no yes Remote Busy Status The remote SAP busy state: no yes Next NS to Send The next sequence number to send Next NS Expected The next Sequence Number expected Link Level Matrix State The state of the Link Level Matrix: • disconDisabled—disconnected disabled • connectingLL—Connecting Link Level
Chapter 5 Call Control Managing ISDN D Channels The system displays DLSAP statistics for the specified line: ======================================================================= Statistics for a DLSAP (lsdlsapstat) ======================================================================= DLSAP : 14.
Chapter 5 Call Control Managing ISDN D Channels Changing D Channels To change a D Channel, delete the desired D Channel and then add a new one. When creating the new channel, choose a DLSAP and MACSAP profile that contains the desired settings. If such a profile doesn’t exist, create one first before adding the new D Channel. For more information on the relationship between D Channels and profiles, see D Channel Configuration Tasks, page 5-19.
Chapter 5 Call Control Managing ISDN D Channels To view D Channel information for a single line, use the lsdchan command. Specify the slot and line number, delimited by a period, of the D Channel. The system displays D Channel information for the specified channel. This information reflects the DLSAP and MACSAP profiles used when adding the D Channel.
Chapter 5 Call Control Managing ISDN D Channels Displayed Information Description T203 Timer The maximum time between retransmission of the TEI identity request message, in seconds. Values 20 to 60. Default: 10 Modulo Each I-frame is sequentially numbered and may have values 0 through (N-1) where N is this modulus. Values: 8 or 128. Default: 128 TEI Assignment The Terminal Endpoint Identifier Assignment setting: 1.
Chapter 5 Call Control Managing ISDN D Channels Displayed Information Description LAPD Type The LAPD interface type: • test—Test • ccitt—CCITT • att5EssBRA—AT&T 5ESS BRA • att5EssPRA—AT&T 5ESS PRA • att4Ess—AT&T 4ESS • ntDMS100BRA—NT dms100 BRA ntDMS100PRA—NT dms100 PRA • vn2or3—VN 2 or VN 3 • insNet—INS Net • tr6MPC—tr6 MPC • tr6PBX—tr6 PBX • ausb—Austel Basic • ausp—Austel Primary • nISDN1—National ISDN-1 • etsi—ETSI • bc303TMC—Bellcore tr303 tmc • bc303CSC—Bellcore tr3
Chapter 5 Call Control Managing ISDN D Channels Displayed Information Description Lowest Range of Automatic TEI The allocated TEI value. When configured for Automatic TEI Assignment, ASP can allocate TEIs greater than or equal to Lowest Automatic TEI. Values: 1 to 127 Keep MAC Up All The Time The state of the Keep MAC Up All The Time flag. Values: 1. False 2. True To view all D Channels, use the lsdchans command.
Chapter 5 Call Control Configuration Tasks for IPDC To view LAPD settings for all cards, use the lslapds command.
Chapter 5 Call Control Configuration Tasks for IPDC Configuring Soft Switch IP Addresses Before beginning this procedure, obtain the IP addresses and ports that apply to your system. Make sure your IP and port selections do not conflict with other equipment on the network. Step 1 Set the primary Soft Switch address and port using the chipdcpssip command as described in the “chipdcpssip” section on page 9-79.
Chapter 5 Call Control Configuration Tasks for IPDC Configuring IPDC Timers and Counters IPDC timers and counters control how the link behaves under abnormal or fault conditions. You can use the default settings, or provide a custom set. To configure IPDC core settings, follow these steps: Step 1 Set the IPDC link timers and retry counters using the chipdctimer command. Step 2 Verify the changes using the lsipdctimer command.
Chapter 5 Call Control Configuration Tasks for IPDC The following information is displayed: ========================================================================= IPDC Soft Switch Configuration (lsipdc) ========================================================================= Primary Soft Switch IP Address : 10.1.1.2 Primary Soft Switch TCP port : 5000 Secondary Soft Switch IP Address : 10.1.1.3 Secondary Soft Switch TCP port : 5000 Gateway IP Address : 10.1.1.
Chapter 5 Call Control Configuration Tasks for IPDC Displayed Information Description Secondary Soft Switch Admin Status The operational state of the backup Soft Switch Graceful Down Timer (sec) The current setting of the graceful shutdown timer Viewing IPDC Timer and Retry Counter Information To view IPDC timer and counter information, use the lsipdctimer command.
Chapter 5 Call Control Configuration Tasks for IPDC Viewing IPDC COT Information To view IPDC COT information, use the lsipdccot command.
C H A P T E R 6 Alarm Surveillance The MGX 8260 Media Gateway notifies maintenance or operations personnel of equipment alarms using the following features and components: • CLI commands • Email alerts • SNMP trap messages • Front panel indicators • Relay contact closures This chapter explains how to monitor alarms from the command line interface, and set up email and trap notifications.
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms Monitoring Shelf Alarms Shelf alarms provide information on environmental, clock, and software operation. When checking alarms, start with commands that list summary information. Then use commands that provide details about the event or condition interest. Step 1 To view shelf alarms, enter the lsalms command.
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms Displayed Information Description Shelf Slot Alarm (Slot 1-16) The slot integrated alarm indicates the combined alarm condition for the specified card and its associated lines and EMM alarms.
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms Monitoring Card Alarms Card alarms provide information on card operation and events. Viewing Card Alarms To view card alarms, follow these steps: Step 1 List information for a card using the lscd command, and specifying the slot location of the card. The system displays the card information.
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms Monitoring DS1 Alarms This section describes viewing DS1 alarm and line status, and setting and viewing alarm thresholds. Viewing DS1/E1 Alarms To view DS1/E1 alarms, follow these steps: Step 1 List alarm information using the lsds1ln command, specifying the slot and line number, delimited by a period, of the line.
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms Viewing DS1 Alarm Thresholds To view DS1 alarm thresholds, enter the lsds1alm command, specifying the slot and line number, delimited by a period, of the line. The system displays the alarm threshold list: ======================================================================= DS1 Line Alarm Thresholds (lsds1alm) ======================================================================= DS1 Line : 16.
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms Table 6-1 DS1 Performance Alarm Thresholds (continued) Threshold Description Default LSES 24 24 hour severely errored seconds 100 PCV 15 15 minute path coding violations 35 PCV 24 24 hour path coding violations 50 PES 15 15 minute path errored seconds 35 PES 24 24 minute path errored seconds 50 PSES 15 15 minute path severely errored seconds 35 PSES 24 24 hour path severely errored seconds 50 SEFS 15 15 minute severely e
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms Monitoring E1 Alarms This section describes the procedures for viewing E1 alarm and line status, and setting and viewing alarm thresholds. Viewing E1 Alarms To view E1 alarms, follow these steps: Step 1 List alarm information using the lse1alrm command, specifying the slot and line number, delimited by a period, of the line.
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms The system displays the following line information: ======================================================================= E1 15 min Performance Alarms (lse1perf15) ======================================================================= E1 Line : 3.
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms Viewing E1 Alarm Thresholds To view E1 performance alarm thresholds, enter the lse1alm command, specifying the slot and line number, delimited by a period, of the line. The system displays the alarm thresholds: E1 Line Alarm Thresholds (lse1alm) ======================================================================= E1 Line : 3.
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms Refer to the following table for a list of threshold counters: Table 6-2 E1 Performance Alarm Thresholds Threshold Description Default1 LCV 15 15 minute line code violations 14 LCV 24 24 hour line code violations 134 LES 15 15 minute line errored seconds 12 LES 24 24 hour line errored seconds 121 UAS 15 15 minute unavailable seconds 10 UAS 24 24 hour unavailable seconds 10 FE ESR 15 15 minute errored second ratio caused by
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms Setting E1 Alarm Thresholds These commands changes the thresholds for various error conditions, such as LCV, LES, and LSES. The performance alarm is set if the line errors exceed any of the threshold counts set by this command. To change performance alarm threshold values, enter the che1alm15 or che1alm24 command. To change alarm severity threshold values, enter the che1almsev command.
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms Viewing DS3 Alarm Thresholds To view DS3 alarm thresholds, enter the lsds3alm command, specifying the The slot and line number, delimited by a period, of the DS3 line. The system displays the alarm threshold list: ======================================================================= DS3 Line Alarm Thresholds (lsds3alm) ======================================================================= DS3 Line : 11.
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms Displayed Information Description DS3 Line The slot and line number of the DS3 line. Red Severity The near end Loss Of Frame indication severity. RAI Severity The Remote Alarm Indication severity. Performance Alarm Severity The performance alarm severity. Performance Alarm Threshold The performance alarm indication. The performance alarm is set if any of the thresholds is exceeded (see Table 6-3).
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms Setting DS3 Alarm Thresholds The chds3alm command changes the configuration settings for alarm severity, integration period, and thresholds for various error conditions, such as LCV, LES, and LSES. The performance alarm is set if the DS3 errors exceed any of the threshold counts set by this command. To change alarm threshold values, enter the chds3alm command as described in the “chds3alm” section on page 9-56.
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms The system displays the following alarm information: ======================================================================= List alarm Severity for all SONET lines (lssonetalms) ======================================================================= Slot.Line Red Severity Yellow Severity Perf Alarm Severity ========= ================ ================ ================= 9.1 major minor minor 9.
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms Bit 12: Path ERDI connectivity defect Bit 13: Path ERDI payload defect Bit 14: Performance failure LOS Bit 15: Performance failure, section LOF Bit 16: Performance failure, line AIS Bit 17: Performance failure, line RFI Bit 18: Performance failure, path AIS Bit 19: Performance failure, path LOP Bit 20: Performance failure, path UEQ Bit 21: Performance failure, path TIM Bit 22: Performance failure, path SLM Bit 23: Path ERDI server failure Bit 24:
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms The system displays the alarm thresholds: ======================================================================= Sonet Line Alarm Thresholds (lssonetalm) ======================================================================= Sonet Line : 9.
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms Table 6-4 OC-3 Performance Alarm Thresholds (continued) Threshold Description Default Section SEFS 24 Hr Threshold Section severely errored frame seconds threshold for 20 24 hours. Line CV 15 Min Threshold Line code violation threshold for 15 minutes. 15 Line CV 24 Hr Threshold Line code violation threshold for 24 hours. 134 Line ES 15 Min Threshold Line errored seconds threshold for 15 minutes.
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms Major alarm EMM Alarm Scale Minor alarm Major low Normal Normal Minor low Normal Minor alarm Minor hi Major alarm Major hi 31932 Figure 6-1 Specifying Sensors In most cases, the MGX 8260 Media Gateway monitors environmental conditions with multiple sensors located at different physical locations. When listing environmental conditions, specify the sensor ID that corresponds to the sensor you want to view.
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms Table 6-8 BSC Sensors SId emmSensorType = temp(1) emmSensorType = voltage(2) 1 Main board bottom 5V 2 Main board top 3.3 V 3 Main board front 2.5 V 4 BIM board top 5 BIM board bottom 6 BIM board middle 7 Main board middle Table 6-9 Chassis Sensors SId emmSensorType = voltage(1) emmSensorType = fan(2) 1 1.5 Volts Bus A Fan number 1 2 1.
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms The system displays the following information: ======================================================================= Environment Monitoring Module Reading (lsemm) ======================================================================= EMM UnitId : slot11 EMM SensorType : voltage-mvolt EMM SensorID : 1 EMM Alarm Status : clear EMM Sensor Reading : 4970 voltage-mvolt Maj Alarm Hi Threshold : 5500 Maj Alarm Lo Threshold : 4500 Min Alarm Hi Thresho
Chapter 6 Alarm Surveillance Surveillance Tasks for Alarms The system displays the following information: ======================================================================= Environment Monitoring Module Reading (lsemm) ======================================================================= EMM UnitId : slot11 EMM SensorType : temp-celsius EMM SensorID : 1 EMM Alarm Status : clear EMM Sensor Reading : 30 temp-celsius Maj Alarm Hi Threshold : 75 Maj Alarm Lo Threshold : -5 Min Alarm Hi Threshold : 70 M
Chapter 6 Alarm Surveillance Configuration Tasks for Alarm Notifications Viewing Environmental Summary Information To view a summary of environmental information, enter the lsemms command.
Chapter 6 Alarm Surveillance Configuration Tasks for Alarm Notifications Configuring User Email Alerts The email facility works in conjunction with SNMP traps to notify registered users of alarms or significant events in the MGX 8260 Media Gateway. A system administrator can register up to ten users for email notifications and up to twenty trap events for each user.
Chapter 6 Alarm Surveillance Configuration Tasks for Alarm Notifications Changing Email Alerts This section explains how to change existing email registrations. To change optional parameters, follow the command line convention described in Chapter 1. For example, to leave a value unchanged type the # symbol as a placeholder. To change an email trap registration, follow these steps: Step 1 Identify the index number of the registration you want to change using the lseregs command.
Chapter 6 Alarm Surveillance Configuration Tasks for Alarm Notifications The following list is displayed: ======================================================================= Email Alert Server & Source Configuration (lsem) ======================================================================= Server Domain Name: cisco.com Server IP Address: 10.1.1.1 Source Email Address: support@cisco.
Chapter 6 Alarm Surveillance Configuration Tasks for Alarm Notifications Configuring SNMP Trap Managers You can register SNMP managers to receive SNMP trap messages on alarms or significant events in the MGX 8260 Media Gateway. Registering SNMP Trap Managers To register an SNMP trap manager, enter the addtmgr command as described in the “addtmgr” section on page 9-33. The bitmap parameter is a bitwise specification of trap categories to subscribe. Each bit represents a category of traps.
Chapter 6 Alarm Surveillance Configuration Tasks for Alarm Notifications You build a trap subscription argument for the addtmgr command. For example, to register for minor alarms, informational messages, card alarms, and DS1 line alarms, build the following trap subscription bitmap: Trap: dsx1Line Bit Value 1 Bit Position 6 SNMP Card Shelf Information Minor Major 0 1 0 1 1 0 5 4 3 2 1 0 To use this bitmap, convert it to a decimal value and specify it as the last argument.
Chapter 6 Alarm Surveillance Working With Traps Viewing SNMP Trap Registrations To view one SNMP trap registration, enter the lstmgr command. The system displays the trap registration information. ======================================================================= Trap Manager Registration Entry (lstmgr) ======================================================================= Trap Manager IP Address (Index) : 10.15.38.
Chapter 6 Alarm Surveillance Working With Traps The system displays the information such as the following: 08/15/2000 08/15/2000 08/15/2000 18:28:21 18:28:19 18:28:19 02 02 02 02 02 02 MAJOR INFO* INFO* TRAP TRAP TRAP Column Description Date The event date Time The event time Physical Slot The physical slot number Logical Slot The logical slot number Severity The event severity Type The type of event Description A text description of the trap Line 7 is in line major alarm 0x00000040
Chapter 6 Alarm Surveillance Working With Traps Card Traps The following table summarizes the alarm conditions and corresponding trap numbers for card alarms: Table 6-12 Card Traps Event Severity Trap Number Card inserted Info 1100 Card removed Info 1101 Card failed Major 1102 Core card switchover Major 1103 Service card switchover Minor 1104 Card major alarm Major 1105 Card minor alarm Minor 1106 Card alarm cleared Info 1107 Card active Info 1108 Core redundancy failed Ma
Chapter 6 Alarm Surveillance Working With Traps Table 6-13 DS1 Traps (continued) Event Severity Trap Number DS1 line alarm cleared Info 1305 DS1 line performance major alarm Major 1306 DS1 line performance minor alarm Minor 1307 DS1 line performance alarm clear Info 1308 DS1 line update threshold Info 1309 DS1 line payload loopback up Info 1310 DS1 line - line loopback up Info 1311 DS1 line other loopback up Info 1312 DS1 line loopback down Info 1313 DS1 line BERT on Info
Chapter 6 Alarm Surveillance Working With Traps Table 6-14 DS3 Traps (continued) Event Severity Trap Number DS3 line other loopback up Info 1412 DS3 line loopback down Info 1413 Event Severity Trap Number SONET line added Info 1500 SONET line deleted Info 1501 SONET line modified Info 1502 SONET line major alarm Major 1503 SONET line minor alarm Minor 1504 SONET line alarm cleared Info 1505 SONET line performance major alarm Major 1506 SONET line performance minor alarm
Chapter 6 Alarm Surveillance Working With Traps Voice Port Events Voice ports generate informational events for configuration changes. The only way to access these events is by using SNMP traps or email alerts.
Chapter 6 Alarm Surveillance Working With Traps Backhaul Traps The following table summarizes the Backhaul conditions and corresponding trap numbers for Backhaul alarms and events: Table 6-20 Backhaul Traps Event Severity Trap Backhaul set added Info 2400 Backhaul set deleted Info 2401 Backhaul group added Info 2402 Backhaul group deleted Info 2403 Backhaul session added Info 2404 Backhaul session deleted Info 2405 Cisco MGX 8260 Command Line Interface Guide 6-36 Release 1.
C H A P T E R 7 Performance Monitoring Monitoring the performance of a communication system is part of a proactive strategy that catches problems before they affect service. The MGX 8260 Media Gateway provides performance information for DS1/E1 and DS3 lines. Monitoring DS1 Performance You can view current or historical statistics that the system collects on DS1 performance. Current statistics are performance statistics collected over the last fifteen minutes.
Chapter 7 Performance Monitoring Monitoring DS1 Performance The system displays the current statistics summary: ======================================================================= DS1 Current Statistics for all Lines (lsds1cursts) ======================================================================= Slot.Line Error Secs SeverSecs FrameSecs UnAvailSecs ========= =========== ========= ========= =========== 13.1 0 0 0 473 13.2 0 0 0 473 13.3 0 0 0 473 13.4 0 0 0 472 13.
Chapter 7 Performance Monitoring Monitoring DS1 Performance To list interval statistics for a T1 line, enter the lsds1intst command, specifying the slot and line number, delimited by a period, of the line and the number (1-96) of the interval of interest. The system displays the interval statistics: ======================================================================= DS1 Line Interval Statistics Entry (lsds1intst) ======================================================================= Slot.Line :13.
Chapter 7 Performance Monitoring Monitoring DS1 Performance Displayed Information Description Alarm State A bitmap of the DS1 line alarms. Zero means no alarm.
Chapter 7 Performance Monitoring Monitoring E1 Performance Clearing Real-Time T1 Statistics To clear T1 real-time statistics, enter the clrds1lnst command, specifying the slot and line number, delimited by a period, of the DS1 line and the statistic to clear. The system clears the specified real-time statistic. Monitoring E1 Performance You can view current or historical statistics that the system collects on E1 performance.
Chapter 7 Performance Monitoring Monitoring E1 Performance The system displays the current statistics summary: ======================================================================= E1 Current Statistics for all Lines (lse1cursts) ======================================================================= Slot.Line Error Secs SeverSecs SlipSecs UnAvailSecs ========= =========== ========= ========= =========== 3.1 0 0 0 0 3.2 0 0 0 0 3.3 0 0 0 0 3.
Chapter 7 Performance Monitoring Monitoring E1 Performance The system displays the 24-hour statistics summary: ============================================================================ E1 Total Stats (lse1totsts) ============================================================================ Slot.Line ErrSecs SeverErrSecs SlipSecs UnAvailSecs LineErSecs ========= ======= ============ ============ =========== ========== 3.1 2 0 2 0 0 3.2 2 0 2 0 0 3.3 2 0 2 0 0 3.
Chapter 7 Performance Monitoring Monitoring E1 Performance Viewing E1 Real-Time Alarm Statistics To view real-time statistics for a single E1 line, enter the lse1lnst command, specifying the slot and line number, delimited by a period, of the line. The system displays the following real-time E1 information: ======================================================================= E1 Line statistics (lse1lnst) ======================================================================= E1 Line : 3.
Chapter 7 Performance Monitoring Monitoring E1 Performance Displayed Information Description Alarm State A bitmap of the E1 line alarms. Zero means no alarm.
Chapter 7 Performance Monitoring Monitoring E1 Performance Displayed Information Description Performance Alarm State A bitmap of E1 line performance alarms. Zero means no alarm.
Chapter 7 Performance Monitoring Monitoring DS3 Performance To view real-time statistics for all E1 lines, enter the lse1lnsts command. The system displays the real-time statistics summary: ======================================================================= E1 Statistics for all Lines (lse1lnsts) ======================================================================= Slot.Line LossOfSignal OutOfFrame CRCErrs FrameErrs ========= ============ ========== ========= =========== 3.1 0 0 0 0 3.2 0 0 0 91 3.
Chapter 7 Performance Monitoring Monitoring DS3 Performance Viewing Current DS3 Statistics Current statistics are performance statistics collected over the last fifteen minutes. To view current statistics for a single DS3, enter the lsds3curst command, specifying the slot and line number, delimited by a period, of the DS3 line.
Chapter 7 Performance Monitoring Monitoring SONET Performance Viewing Interval DS3 Statistics Interval statistics are collected by each DS3 Interface for the previous 24 hours of operation. The 24 hours are broken into 96 15-minute intervals, where interval 1 is the most recent and 96 is the oldest. As time progresses, the system drops the oldest interval and adds the latest one, creating a sliding 24-hour window that moves with time.
Chapter 7 Performance Monitoring Monitoring SONET Performance • Line • Path Monitoring SONET Section Statistics Viewing Section Current Statistics Current statistics are performance statistics collected over the last fifteen minutes. To view current statistics for a single line, enter the lsssectioncst command, specifying the slot and line number delimited by a period.
Chapter 7 Performance Monitoring Monitoring SONET Performance Viewing Section Total Statistics Total statistics are performance statistics collected since the previous midnight. So just before midnight there are almost 24 hours of statistics available, at midnight the statistic counters are reset, and after midnight the system starts accumulating new data. To view total statistics for a single line, enter the lsssectiontst command, specifying the slot and line number delimited by a period.
Chapter 7 Performance Monitoring Monitoring SONET Performance To view interval statistics for a single line, enter the lsssectionist command, specifying the slot and line number, delimited by a period, and the desired interval. The system displays the interval statistics: ======================================================================= Sonet Section Interval Statistics (lsssectionist) ======================================================================= Sonet section Slot.Line : 9.
Chapter 7 Performance Monitoring Monitoring SONET Performance Monitoring SONET Line Statistics Viewing Line Current Statistics Current statistics are performance statistics collected over the last fifteen minutes. To view current statistics for a single line, enter the lsslinecst command, specifying the slot and OC-3 line number delimited by a period.
Chapter 7 Performance Monitoring Monitoring SONET Performance Viewing Line Total Statistics Total statistics are performance statistics collected since the previous midnight. So just before midnight there are almost 24 hours of statistics available, at midnight the statistic counters are reset, and after midnight the system starts accumulating new data. To view total statistics for a single line, enter the lsslinetst command, specifying the slot and line number delimited by a period.
Chapter 7 Performance Monitoring Monitoring SONET Performance To view interval statistics for a single line, enter the lsslineist command, specifying the slot and line number, delimited by a period, and the desired interval. The system displays the interval statistics: ======================================================================= Sonet Line Interval Statistics (lsslineist) ======================================================================= Sonet Line Slot.Line : 9.
Chapter 7 Performance Monitoring Monitoring SONET Performance Monitoring SONET Path Statistics Viewing Path Current Statistics Current statistics are performance statistics collected over the last fifteen minutes. To view current statistics for a single line, enter the lsspathcst command, specifying the slot and OC-3 line number delimited by a period.
Chapter 7 Performance Monitoring Monitoring SONET Performance Viewing Path Total Statistics Total statistics are performance statistics collected since the previous midnight. So just before midnight there are almost 24 hours of statistics available, at midnight the statistic counters are reset, and after midnight the system starts accumulating new data. To view total statistics for a single line, enter the lsspathtst command, specifying the slot and line number delimited by a period.
Chapter 7 Performance Monitoring Monitoring SONET Performance To view interval statistics for a single line, enter the lsspathist command, specifying the slot and line number, delimited by a period, and the desired interval. The system displays the interval statistics: ======================================================================= Sonet Path Interval Statistics (lsspathist) ======================================================================= Sonet Path Slot.Line : 9.
Chapter 7 Performance Monitoring Monitoring SONET Performance Monitoring SONET Alarm Statistics To view real-time statistics for a single line, enter the lssonetstat command, specifying the slot and line number, delimited by a period. The system displays the following alarm statistics: ======================================================================= Sonet Line statistics (lssonetstat) ======================================================================= Sonet Line : 9.
Chapter 7 Performance Monitoring Monitoring SONET Performance Displayed Information Description Performance Alarm State A bitmap of SONET line performance alarms. Zero means no alarm.
Chapter 7 Performance Monitoring Monitoring SONET Performance Clearing SONET Performance Alarm Statistics To clear statistics, enter the clrsonetstats command, specifying the slot and line number, delimited by a period, and the statistical counter to clear.
Chapter 7 Performance Monitoring Monitoring SONET Performance Cisco MGX 8260 Command Line Interface Guide 7-26 Release 1.2, Part Number 78-10987-01 Rev.
C H A P T E R 8 Troubleshooting The MGX 8260 Media Gateway includes diagnostic features that facilitate fault location, such as loopback and bit error rate tests. See the following sections for information on how to locate and clear trouble conditions. • Performing Loopback Tests • Performing BERT Tests • Clearing Alarms Performing Loopback Tests Loopback tests are powerful troubleshooting tools that help maintenance personnel locate faults along the transmission path.
Chapter 8 Troubleshooting Performing Loopback Tests Warning Loopback testing interrupts service. Perform during in a pre-arranged maintenance window or when the line is down. DS1/E1 Loopback To perform a DS1/E1 loopback test, follow these steps: Step 1 Activate the loopback using the chds1ln. Specify the first and last parameters—the slot and line number, delimited by a period, of the DS1 line and the type of loopback test.
Chapter 8 Troubleshooting Performing Loopback Tests DS3 Loopback To perform a DS3 loopback test, follow these steps: Step 1 Activate the loopback using the chds3ln command. Specify the first and last parameters—the slot and line number, delimited by a period, of the DS1 line and the type of loopback test. Refer to the following table: Value Name Note 1 dsx3NoLoop 2 dsx3PayloadLoop 3 dsx3LineLoop 4 dsx3OtherLoop Local loopback for DS3 lines is not supported.
Chapter 8 Troubleshooting Performing BERT Tests SONET Loopback To perform a SONET loopback test, follow these steps: Step 1 Activate the loopback using the chsonetln command, specifying the slot, line, and loopback type. Refer to the following table for the loopback type: Value Name Note 1 No loop 2 Line loop 3 Serial loop 4 Parallel loop Serial and parallel loops are both local loopback states. For example, the following command loops line 2 on slot 9: chsonetln 9.
Chapter 8 Troubleshooting Performing BERT Tests DS1/E1 BERT Test To use the DS1/E1 BERT test, follow these steps: Step 1 Activate the test signal using the onbertds1 command as described in the “onbertds1” section on page 9-357. For example, the following command activates the bert test on channel 1 of line 1 in slot 11 using a rand9Bit pattern with no error injection. onbertds1 11.
Chapter 8 Troubleshooting Clearing Alarms Clearing Alarms The MGX 8260 Media Gateway has the following alarm categories: • Shelf • Card • DS1, E1, and DS3 • Fast Ethernet • OC-3 • Environmental If you know the alarm source, proceed to the corresponding section of this chapter. Otherwise, start at the shelf level and work toward the cause. Clearing Chassis Alarms Chassis alarms report the state of chassis environmental sensors, fan speed, card state, and 48 supply status.
Chapter 8 Troubleshooting Clearing Alarms Displayed Information Description EMM temperature alarm A temperature sensor raised an environmental alarm. Follow instructions in the “Clearing Environmental Alarms” section on page 8-11. EMM voltage alarm A voltage sensor raised an environmental alarm. Follow instructions in the “Clearing Environmental Alarms” section on page 8-11. Component failure alarm A hardware component of the card failed.
Chapter 8 Troubleshooting Clearing Alarms Displayed Information LOSMF (E1 only) Yellow (RAI) RMAI (E1 only) Possible Cause and Corrective Action • Check for framing format misconfiguration • Check for TS16 alteration • Check for bit errors in TS16 • Check for line coding misconfiguration • Check the transmit on the near end • Check the physical connection • Perform a BERT to verify the line condition • Check the transmit of TS16 at the near end • Check the physical connection • Perf
Chapter 8 Troubleshooting Clearing Alarms Clearing Fast Ethernet Alarms The MGX 8260 Media Gateway monitors the Fast Ethernet trunks for conditions that can cause service interruption. To view Fast Ethernet line state, enter the lsethlns command. The system displays a summary of the trunk status, including the Operational Status for each line.
Chapter 8 Troubleshooting Clearing Alarms Respond to minor alarms according to the guidelines in the following table: Minor Alarm Corrective Action1 AIS-L The problem originated from an upstream node; investigate nodes in upstream direction RFI-L AIS-P RFI-P • Activate a line loopback at the remote node and isolate problem by checking the looped signal • Verify the physical connection (cables and connectors) in the MGX 8260 Media Gateway transmit direction The problem originated from an upstrea
Chapter 8 Troubleshooting Clearing Alarms Symptom Corrective Action SCC fails initialization • Use the lsevt command to check for error events logged during initialization and look for a possible OC3 hardware failure SCC back card type not properly programmed • escalate problem to customer support Clearing Environmental Alarms The MGX 8260 Media Gateway monitors temperature and voltage at several points in the shelf and on the cards. To view environmental alarms, enter the lsemms command.
Chapter 8 Troubleshooting Clearing Alarms Cisco MGX 8260 Command Line Interface Guide 8-12 Release 1.2, Part Number 78-10987-01 Rev.
C H A P T E R 9 Command Reference The MGX 8260 Media Gateway Media Gateway uses a command line interface for system administration, configuration, and service provisioning. This chapter covers the security requirement, syntax, general description, example, and related topics for each command. Command Line Interface Guidelines The MGX 8260 Media Gateway command line interface supports write and read commands. The MGX 8260 Media Gateway command line interface translates write commands to SNMP Set requests.
Chapter 9 Command Reference Understanding Bitmaps Understanding Bitmaps The MGX-8260 command line interface reports some parameters as binary bitmaps. A bitmap is a compact way of representing multiple binary indicators using a single decimal value. To interpret the bitmap, you must convert it to a binary number and then interpret the individual bit positions. For example, the MGX-8260 Media Gateway reports the card service type as a decimal value that indicates one of four possible service types.
Chapter 9 Command Reference Using Online Help Using Online Help The MGX-8260 command line interface includes online help. Command Syntax Help To get help for a command, type the command without parameters.
Chapter 9 Command Reference acannfile acannfile Activate an announcement file. acannfile fid Syntax Description fid Defaults No default behavior or values. Command Modes Security level 3 Command History Release Modification 1.2 This command was first introduced. The announcement file ID. Values: 1-100 Usage Guidelines You use this command to activate an announcement file. To view announcement file ID numbers, use the lsannfiles command.
Chapter 9 Command Reference addcms addcms Add the community string that applies to an SNMP manager who subscribes to receive information on traps. addcms Comm-Str MgrAddr [Privilege] Syntax Description Comm-Str An SNMP community string, such as “Public”. Values: string of up to 20 characters. MgrAddr The IP address of the SNMP manager who wants to receive trap events. If the management IP address is set to 0.0.0.0, the community string applies to all IP addresses. Privilege Read permission.
Chapter 9 Command Reference adddchan adddchan Add a D Channel. adddchan Index Repetitions DlSapProfile MacSapProfile DS0 DS0format Syntax Description Defaults Index The slot and line number, delimited by a period, of the new D Channel. Repetitions The number of sequential lines to add. Values: 1 to 1136. DlSapProfile The DLSAP profile number associated with the D Channel. Values: 1-10. MacSapProfile The MACSAP profile number associated with the D Channel. Values: 1-10.
Chapter 9 Command Reference adddchan Command Description deldchan Delete a D Channel lsdchan List information about a D Channel lsdchans List information about D Channels Cisco MGX 8260 Command Line Interface Guide Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference adddlsp adddlsp Add a DLSAP profile. adddlsp dlsapProfIndex [dlsapFrameLen dlsapWinSize dlsapRetransCount dlsapCongestionTimer dlsapt200Timer dlsapt203Timer dlsapModulo dlsapTEIAssign dlsapMaxDlcs dlsapTEI] Syntax Description dlsapProfIndex The identifier of a DLSAP Profile. Values: 1 - 20 dlsapFrameLen The frame length, which is the maximum number of octets in an information field.
Chapter 9 Command Reference adddlsp Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines The DLSAP (Digital Link Service Access Point) profile defines a collection of settings for the D Channel protocol stack. These settings describe the operating characteristics of the interface between LAPD and Q.931 call control. You assign a DLSAP profile when adding a D Channel management path.
Chapter 9 Command Reference addds1ln addds1ln Add DS1 (T1 or E1) lines. addds1ln Location numOfLines [LineType LineCoding SendCode LoopConfig LineSignalMode XmitClkSrc SignalBits IdleCode] Syntax Description Location The slot and line number, delimited by a period, of the new DS1 line. For example, enter slot 3 line 2 as 3.2. Valid slot numbers: • NSC: 1-8 and 11-16 • BSC: 11-16 Valid line numbers: • NSC: 1-16 • BSC: 1-168 as shown by the following table of DS1 to DS3 mappings.
Chapter 9 Command Reference addds1ln SendCode The type of code being sent across the DS1 interface by the device. Values are 1 - 8 and have the following names: 1=dsx1SendNoCode 2=dsx1SendLineCode (T1 lines only) 3=dsx1SendPayloadCode (reserved for future use) 4=dsx1SendResetCode (T1 lines only) 5=dsx1SendQRS (T1 lines only) 6=dsx1Send511Pattern (T1 or E1) 7=dsx1Send3in24Pattern (T1 or E1) 8=dsx1Send1in16 (T1 lines only) LoopConfig The loopback configuration of the DS1 interface.
Chapter 9 Command Reference addds1ln SignalBits The 4-bit signaling pattern, represented by an integer: 1=0000 2=0001 3=0010 4=0011 5=0100 6=0101 ... 16=1111 IdleCode The code that is sent on each idle DS0 within the DS1 line. Values: 0-255 1.
Chapter 9 Command Reference addds1ln Examples The following example adds a DS1 line with AMI line coding to slot 13 line 6: addds1ln 13.
Chapter 9 Command Reference addds3ln addds3ln Add a DS3 line. addds3ln Location [RepeatLines LineType LineCoding SendCode LoopCfg XmitClkSource CableLength] Syntax Description Location The slot and line number, delimited by a period, of the new DS3 line. Valid slot numbers: BSC: 11-16 DMC: 7 or 8 (reserved for future use) Valid line numbers: BSC: 501-506 DMC: 1-6 (reserved for future use) RepeatLines The number of lines you can add in a single request. Values are 1 - 76.
Chapter 9 Command Reference addds3ln SendCode The type of code being sent across the DS3/E3 interface by the device. (Optional for E3 interfaces.
Chapter 9 Command Reference addds3ln Command History Usage Guidelines Note Examples Release Modification 1.0 This command was first introduced. 1.1 BSC card configuration - no functional change Use this command to add one or more DS3 lines to BSC or DMC circuit cards. If you do not enter optional parameters the default value is used. When adding a range of lines, the process stops at the first error.
Chapter 9 Command Reference addereg addereg Add email registration. addereg Index Address Trap#1 [Trap#2 ... Trap#20] Syntax Description Index A unique number that identifies one of the ten users. Values: 1-10. Address The email address, up to 40 characters, of the person who wants to receive email about traps. For example, admin@cisco.com. Trap The number of the trap condition to register. When the trap occurs, the system sends an email to the user.
Chapter 9 Command Reference addethln addethln Add Ethernet line. addethln Location Addr [Prim_IPGW_Addr AddTargetState RDP Mask Mode] Syntax Description Defaults Location The slot and line number, delimited by a period, of the new Ethernet line. Slot values: 9 Line values: 1-4. Addr IP Address in dot notation w.x.y.z. Prim_IPGW_Addr The IP address of the primary gateway for the interface. AddTargetState The state, active or inactive, of the line after the line is added.
Chapter 9 Command Reference addethln Command Description lsethln List Ethernet line lsethlns List Ethernet Lines Cisco MGX 8260 Command Line Interface Guide Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference addiproute addiproute Add an IP route. addiproute IPRouteDestination nexthop IPRouteMask Syntax Description IPRouteDestination The destination IP address of this route. An entry of 0.0.0.0 is considered a default route. nexthop The IP address of the next hop of this route. If a route is bound to an interface (through a broadcast media), the value of this field is the agent's IP address on the interface.
Chapter 9 Command Reference addm13 addm13 Add map to DS1 from DS3. addm13 SrcDS3LineNum SrcDS1LineNum DestDS1SlotNum DestDS1LineNum [NoOfLines] Syntax Description SrcDS3LineNum The number of the source DS3 line. Values: 1 - 6. SrcDS1LineNum The number of the DS1 line, or starting DS1 line, within the DS3 line. Values: 1 - 28. DestDS1SlotNum The logical slot number for the destination NSC card. When mapping a range of DS1 lines, this is the starting slot. Values: 1-6 and 11-16.
Chapter 9 Command Reference addmacsapprof addmacsapprof Add a MACSAP profile. addmacsapprof Index [sapIf LinkArb LapdType MaxOutStFrames TimQUpperThresh TimeQLowerThresh ConnTimer t201Timer t202Timer TEICheckTimer N202 LowAutoTei KeepL1Up] Syntax Description Index The identifier of a MAC SAP. Values: 1 - 20. sapIf The logical Interface. Values: 1 = user, 2 = network. LinkArb Link setup arbitration scheme. Values: 1 = passive, 2 = active. LapdType The type of LAPD interface.
Chapter 9 Command Reference addmacsapprof t201Timer The T201 timer value. Values: 1 to 1024 t202Timer The T202 timer value. Values: 1 to 1024 TEICheckTimer The setting of the TEI check timer. Values: 1 - 1025. 1025 = disabled. N202 The maximum number of transmissions of a TEI Identity request message. LowAutoTei The value that is greater than or equal to the lowest automatic TEI that the ASP can allocate. Applicable only when configured for automatic TEI assignment.
Chapter 9 Command Reference addmacsapprof Related Commands Command Description delmacsapprof Delete a MACSAP profile lsmacsapprof List information about a MACSAP profile lsmacsapprofs List all MACSAP profiles lsmacsapstat List statistics for a MACSAP interface lsmacsapstats List MACSAP statistics Cisco MGX 8260 Command Line Interface Guide 9-24 Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference addreds addreds Add card redundancy. addreds PrimarySlot SecondarySlot Syntax Description PrimarySlot Physical location of the primary card in the chassis. Valid settings: 1-8 and 11-16. SecondarySlot Physical location of the secondary card in the chassis. Valid settings: 1-8 and 11-16. Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.0 This command was first introduced.
Chapter 9 Command Reference addsess addsess Add an MGCP session manager. addsess SessionSetId GroupId SessionId LocalAddr LocalPort RemoteAddr RemotePort Priority Syntax Description SessionSetId The index of the session set to which the group containing the session manager belongs. Values: 1-6. GroupId The index of the session group to which the session manager belongs. Values: 1 or 2. SessionId The index of this session. Values: 1 or 2 LocalAddr The local IP address of the session.
Chapter 9 Command Reference addsgrp addsgrp Add an MGCP session group. addsgrp GroupSetId GroupId Syntax Description GroupSetId The index of the set to which this group belongs. Values: 1-6 GroupId The index of the session group to which the session manager belongs. Values: 1 or 2. Defaults No default behavior or values. Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced.
Chapter 9 Command Reference addsonetln addsonetln Add a SONET line. addsonetln Location [numOfLines MediumType LoopConfig HCSmasking PayloadScrambling FrameScrambling TxClockSource] Syntax Description Location The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 numOfLines The number of lines to add. Values: 1-4.
Chapter 9 Command Reference addsonetln Command History Usage Guidelines Release Modification 1.2 This command was first introduced. Use this command to configure optical SONET/SDH interfaces on the OC-3 SCC and back card. Although the SCC may occupy physical slots 9 or 10, you always configure logical slot 9. You can add a single line or a range of identically-configured lines with this command.
Chapter 9 Command Reference addsrt addsrt Add static route addsrt Destination Slot.Line [RoutePriority] Syntax Description Destination The IP address of a remote network with which you want a static route. The last byte of the IP number must be zero. For example, 127.2.4.0 is valid Slot.Line The slot and line number, delimited by a period, of the origin of the static route.
Chapter 9 Command Reference addsset addsset Add an MGCP session set. addsset SessSetId MinSlot MinLine MaxSlot MaxLine RedunMode Syntax Description SessSetId Session set index. Values: 1-6. MinSlot The minimum slot number within the MGX 8260 Media Gateway chassis assigned for this session set. Values: 1-8 and 11-16. MinLine The minimum line number assigned for this Session Set. Values: 1-168 for the BSC; 1-16 for the NSC.
Chapter 9 Command Reference addsset Command Description delsset Delete a session set delsgrp Delete a session group Cisco MGX 8260 Command Line Interface Guide 9-32 Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference addtmgr addtmgr Add trap manager. addtmgr Addr [Port Interface Com_String Bitmap] Syntax Description Addr The IP address of the SNMP manager who wants to receive trap events. Port UDP number of port to which the traps are transmitted. Interface The default interface for initially sending traps if the routing table has no trap manager. Values: 1, 2, 3. These values have the following names and meanings: 1=scc-eth-if—The default system Ethernet management interface on SCC.
Chapter 9 Command Reference addtmgr Bitmap A bitwise specification of trap categories to subscribe. Each bit represents a category of traps. Bit values: 1 = subscribe 0, = do not subscribe.
Chapter 9 Command Reference addtmgr Usage Guidelines Network administrators can receive email notifications for up to 20 trap events. Use this command to subscribe a manager to receive notification about specific trap events. Examples The following example subscribes the manager at address 10.1.1.10 and udp port 162 to receive minor and informational messages for cards and DS1 lines.
Chapter 9 Command Reference addusp addusp Add user profile. addusp Name Access_Level Syntax Description Name The login name of the new user, expressed as a case-sensitive alphanumeric string of four to ten characters. Special characters such as @, #, and $ are allowed. Access_Level A value associated with a user profile that determines access rights to the MGX-8260 CLI and WebViewer. Defaults No default behavior or values.
Chapter 9 Command Reference addusp Examples The following example adds a user named william with Administrator level privileges. addusp william 2 Related Commands Command Description chkey Change file key delusp Delete user profile Cisco MGX 8260 Command Line Interface Guide Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference addvport addvport Add voice port. addvport SlotNum PortNum LineNum DS0Num [RepititionNum WrapNum Dejitter DejitterBufLen Maxdj Mindj PacketLoading EchoTail] Syntax Description SlotNum The logical slot number of an NSC. Values: 1 to 16 PortNum The logical port number for the new port. Values: 1 to 512 LineNum The number of the DS1/E1 line for the voice port. Values: 1 to 16 DS0Num The number of the DS0 within the DS1/E1 for the new port.
Chapter 9 Command Reference addvport DejitterBufLen: 2 Maxdj: 50 Mindj: 1 PacketLoading: 1 EchoTail: 5 Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced. 1.2 Added repetition and wrap arguments Usage Guidelines Use this command to add one or more voice ports. The DS1/E1 line must already exist before using this command.
Chapter 9 Command Reference bye bye Log out. bye Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Examples Type this command to log out from the MGX 8260 Media Gateway The following command logs out. bye Related Commands Command Description exit Logs out from the MGX 8260 Media Gateway. logout Logs out from the MGX 8260 Media Gateway.
Chapter 9 Command Reference chcdif chcdif Configure card interface. chcdif Card Mode Syntax Description Card The number of an NSC card. Mode Indicates whether the Narrowband Service Card (NSC) transmits and receives traffic through the back card or redirected through the backplane from the DC3 interface on the Distribution Matrix Card (DMC). Values: 1=back card 2=back plane 3=not applicable (no back card) Defaults No default behavior or values.
Chapter 9 Command Reference chcsbaynum chcsbaynum Change control server bay number (reserved for future use). chcsbaynum Number Syntax Description Number Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.0 This command was first introduced. A string that represents the CS bay number. Values: a string of exactly 8 characters. Usage Guidelines Configures the string that identifies the bay number of the MCS.
Chapter 9 Command Reference chcsid chcsid Change control server system ID (reserved for future use). chcsid ID Syntax Description ID Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.0 This command was first introduced. The system ID of the MCS. Value: user-defined text string, up to 24 characters Usage Guidelines Use this command to configure a user-defined identifier for the MCS.
Chapter 9 Command Reference chcsnumfor chcsnumfor Specify the MCS numbering format for modules, lines and channels (reserved for future use). chcsnumfor format Syntax Description format Specification to start module, line, and channel numbering at 0 or 1. 1 = One-based 2 = Zero-based Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.0 This command was first introduced.
Chapter 9 Command Reference chcstype chcstype Change control server type (reserved for future use). chcstype type Syntax Description type Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.0 This command was first introduced. An alphanumeric string. The string must be exactly 9 characters in length. Usage Guidelines Configures the string used to identify the manufacturer and model of the MCS.
Chapter 9 Command Reference chdate chdate Change date. chdate date Syntax Description date Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.0 This command was first introduced. The system date expressed as mm/dd/yyyy. Values: 1970 - 2099 Usage Guidelines Use this command to configure or change the system date. Examples The following example sets the system date to January 14, 2001.
Chapter 9 Command Reference chds1alm chds1alm Change DS1 alarm severity and thresholds. chds1alm Location [Red_Severity RAI_Severity Perf_Alarm_Severity LCV_15 LCV_24 LES_15 LES_ 24 LESES_15 LESES_24 SEFS_15 SEFS_24 PSAS_15 PSAS_24 UAS_15 UAS_24 PCV_15 PCV_24 PES_15 PES_24 SES_15 SES_24 BES_15 BES_24 PCSS_15 PCSS_24 Syntax Description Location The slot and line number, delimited by a period, of the DS1 line Red_Severity The near end LOF indication, either minor or major. Values: 1 or 2, respectively.
Chapter 9 Command Reference chds1alm Defaults No default behavior or values. The following defaults apply to a new DS1 line: Red_Severity: 2 RAI_Severity: 1 Perf_Alarm_Severity: 1 LCV_15: 14 LCV_24: 134 LES_15: 12 LES_24: 121 LSES_15: 10 LSES_24: 100 SEFS_15: 2 SEFS_24: 17 PSAS_15: 2 PSAS_24: 17 UAS_15: 10 UAS_24: 10 PCV_15: 35 PCV_24: 50 PES_15:35 PES_24:50 PSES_15: 35 PSES_24: 50 BES_15: 35 BES_24: 50 PCSS_15: 35 PCSS_24: 50 Command Modes Security level 2 Command History Release Modification 1.
Chapter 9 Command Reference chds1alm Examples The following example changes the 15-minute LCV thresholds for line 1 of slot 1 from the default value to 15. chds1alm 1.
Chapter 9 Command Reference chds1ln chds1ln Change DS1 (T1 or E1) lines. chds1ln Location numOfLines [LineType LineCoding SendCode LoopConfig LineSignalMode XmitClkSrc SignalBits IdleCode] Syntax Description Location The slot and line number, delimited by a period, of the new DS1 line. For example, enter slot 3 line 2 as 3.2. Valid slot numbers: • NSC: 1-8 and 11-16 • BSC: 11-16 Valid line numbers: • NSC: 1-16 • BSC: 1-168 as shown by the following table of DS1 to DS3 mappings.
Chapter 9 Command Reference chds1ln LineCoding Theline coding format. Not applicable for T1 lines added to the BSC. The valid entries are: 1=dsx1JBZS (reserved for future use) 2=dsx1B8ZS (T1 lines only) 3=dsx1HDB3 (E1 lines only) 4=dsx1ZBTSI (reserved for future use) 5=dsx1AMI 6=other (reserved for future use) SendCode The type of code being sent across the DS1 interface by the device.
Chapter 9 Command Reference chds1ln SignalBits The 4-bit signaling pattern, represented by an integer: 1=0000 2=0001 3=0010 4=0011 5=0100 6=0101 ... 16=1111 IdleCode The code that is sent on each idle DS0 within the DS1 line. Values: 0-255 Defaults No default behavior or values. Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced. 1.
Chapter 9 Command Reference chds1ln Command Description lsds1curst List DS1 line current statistics lsds1cursts List DS1 current statistics lsds1intst List DS1 interval statistics lsds1ln List DS1 line lsds1lns List DS1 lines lsds1lnst List DS1 line statistics lsds1totst List DS1 line total statistics lsds1totsts List DS1 total statistics lslns List existing lines offbertds1 Stop BERT on DS1 onbertds1 Start BERT on DS1 Cisco MGX 8260 Command Line Interface Guide Release 1.
Chapter 9 Command Reference chds1lnecho chds1lnecho Configure the echo canceller for a DS1 line. chds1lnecho Location State Syntax Description Location The slot and line number, delimited by a period, of the DS1 line. For example, enter slot 3 line 2 as 3.2. Valid slot numbers: • NSC: 1-8 and 11-16 • BSC: 11-16 Valid line numbers: • NSC: 1-16 • BSC: 1-168 as shown by the following table of DS1 to DS3 mappings.
Chapter 9 Command Reference chds1lnecho Examples The following example enables echo cancelling on slot 12, line 1 of the BSC card. chds1lnecho 12.1 1 Related Commands Command Description chipdcpssip Change IPDC primary Soft Switch IP and TCP port Cisco MGX 8260 Command Line Interface Guide Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference chds3alm chds3alm Change DS3 alarm severities and performance alarm thresholds.
Chapter 9 Command Reference chds3alm AISS15MinThreshold AISS24HrThreshold UAS15MinThreshold UAS24HrThreshold CCV15MinThreshold CCV24HrThreshold CES15MinThreshold CES24HrThreshold CSES15MinThreshold CSES24HrThreshold Defaults The threshold for alarm indication signals in a 15-minute window or sliding 24-hour window. The threshold for unavailable seconds in a 15-minute window or sliding 24-hour window. The threshold for C-bit coding violations in a 15-minute window or sliding 24-hour window.
Chapter 9 Command Reference chds3alm SEFS15MinThreshold: 10 CSES24HrThreshold: 10 Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced. 1.1 BSC card configuration - no functional change Usage Guidelines Use this command to change alarm thresholds. For details on threshold counts, refer to Table 6-3 on page 6-14. Examples The following example changes the dsx3PerfAlmSeverity at DS3 line at slot 7 line 1 to major (2). chds3alm 7.
Chapter 9 Command Reference chds3ln chds3ln Change DS3 line. chds3ln Location numOfLines [LineType LineCoding SendCode LoopConfig XmitClkSrc Cable] Syntax Description Location The slot and line number, delimited by a period, of the DS3 line. Valid slot numbers: BSC: 11-16 DMC: 7 or 8 (reserved for future use) Valid line numbers: BSC: 501-506 DMC: 1-6 (reserved for future use) numOfLines Number of lines to change. Values: 1-76.
Chapter 9 Command Reference chds3ln SendCode The type of code being sent across the DS3/E3 interface by the device. (Optional for E3 interfaces.
Chapter 9 Command Reference chds3ln Examples The following command loops line 2 on DMC slot 7: chds1ln 7.2 # # # # 2 Related Commands Command Description addds3ln Add DS3 line chds3alm Change DS3 line alarm clrds3lnst Clear statistics for DS3 line delds3ln Delete DS3 line lsds3alm List DS3 alarm lsds3lns List DS3 lines lsds3totst List DS3 total statistics Cisco MGX 8260 Command Line Interface Guide Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference che1alm15 che1alm15 Change 15-minute E1 alarm thresholds. che1alm15 Location [LCV_15 LES_15 UAS_15 FE_ESR_15 FE_SESR_15 FEBE_ESR_15 FEBE_SESR_15 CRC_ESR_15 CRC_SESR_15 ES-ESR_15 SES_ESR_15 ES_15 SES_15 BE_15 PCV_15 CSS_15] Syntax Description Defaults Location The slot and line number, delimited by a period, of the DS1 line LCV_15 The threshold for LCV (Line Code Violations). A code violation is either a bipolar violation or excessive zeroes event.
Chapter 9 Command Reference che1alm15 CRC_SESR_15: 20 ES_ESR_15:800 SES_ESR_15: 20 ES_15:35 SES_15: 35 BE_15: 35 PCV_15: 14 CSS_15: 35 Command Modes Security level 2 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to change the 15-hour thresholds for various error conditions, such as LCV, LES, and LSES. All counter thresholds are integers greater than zero.
Chapter 9 Command Reference che1alm24 che1alm24 Change 24-hour E1 alarm thresholds. che1alm24 Location [LCV_24 LES_24 UAS_24 FE_ESR_24 FE_SESR_24 FEBE_ESR_24 FEBE_SESR_24 CRC_ESR_24 CRC_SESR_24 ES-ESR_24 SES_ESR_24 ES_24 SES_24 BE_24 PCV_24 CSS_24] Syntax Description Defaults Location The slot and line number, delimited by a period, of the DS1 line LCV_24 The threshold for LCV (Line Code Violations). A code violation is either a bipolar violation or excessive zeroes event.
Chapter 9 Command Reference che1alm24 CRC_SESR_24: 20 ES_ESR_24:800 SES_ESR_24: 20 ES_24: 15: 50 SES_24: 50 BE_24: 50 PCV_24: 50 CSS_24: 50 Command Modes Security level 2 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to change the 24-hour thresholds for various error conditions, such as LCV, LES, and LSES. All counter thresholds are integers greater than zero.
Chapter 9 Command Reference che1almsev che1almsev Change E1 alarm severity. che1almsev Location [Red_Severity RAI_Severity RMAI_Severity TS16_Severity Perf_Alarm_Severity ] Syntax Description Defaults Location The slot and line number, delimited by a period, of the DS1 line Red_Severity The near end LOF indication, either minor or major. Values: 1 or 2, respectively. RAI_Severity The remote alarm indication, either minor or major. Values: 1 or 2, respectively.
Chapter 9 Command Reference che1almsev Related Commands Command Description addds1ln Add DS1 line chds1ln Change DS1 line che1alm15 Change 15-minute E1 alarm thresholds che1alm24 Change 24-hour E1 alarm thresholds clrds1lnst Clear DS1 line statistics delds1ln Delete DS1 line lse1alm List E1 alarm thresholds lse1curst List E1 line current statistics lse1cursts List E1 current statistics lse1intst List E1 interval statistics lsds1ln List DS1 line lsds1lns List DS1 lines lse1lnst
Chapter 9 Command Reference chem chem Configure email registration. chem [EmailServerDomain EmailServerIPAddr SourceEmailAddr] Syntax Description EmailServerDomain The domain name of the email server on your network. Values: A text string, maximum 30 characters. EmailServerIPAddr The IP address of the email server in standard IP dot notation. The 0.0.0.0 setting disables email notifications. Any valid IP address enables email notifications.
Chapter 9 Command Reference chereg chereg Change email registration. chereg Index EmailAddress Trap#1 [Trap#2 ... Trap#20] Syntax Description Index Position of the email address in the SnmpEmailRegTable. Values: integer, 1-10. EmailAddress The email address, up to 40 characters, of the person who wants to receive email about traps. Trap#n One to twenty existing trap numbers. Defaults No default behavior or values. Command Modes Security level 3 Command History Release Modification 1.
Chapter 9 Command Reference chethln chethln Change Fast Ethernet line. chethln Location [Gway_Addr RDP Mask Mode] Syntax Description Location The slot and line number, delimited by a period, of the Ethernet line. Values: Slot = 9, Line = 1-4. Gway_Addr The IP address of the primary gateway for the interface. RDP The state of the Router Discovery Protocol. Values: 1 = disabled, 2 = enabled. Mask The subnet mask in dotted notation a.b.c.d. Mode The duplex mode of the line.
Chapter 9 Command Reference chgw chgw Specify a gateway router. chgw Address Syntax Description Address Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.2 This command was first introduced. An IP address in dotted notation w.x.y.z Usage Guidelines Use this command to configure the gateway IP address for management traffic. The system uses this gateway to route management traffic outside the local subnet.
Chapter 9 Command Reference chibip chibip Configure in-band IP. chibip Address Mask Syntax Description Address An IP address in dotted notation w.x.y.z Mask A subnet mask in dotted notation a.b.c.d Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to configure the IP address and mask of the in-band system management interface.
Chapter 9 Command Reference chidletm chidletm Change idle time before session termination. chidletm idleTime Syntax Description idleTime Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. The idle time in minutes. Values: 0 - 2147483647. 0 = infinity. Usage Guidelines Use this command to change the amount of time allowed for no keyboard input. When the time expires, the session terminates.
Chapter 9 Command Reference chipdccot chipdccot Change IPDC COTs. chipdccot rcot tcot Syntax Description Defaults rcot IPDC COT receive tone. Values: co1 (2010 Hz) or co2 (1780 Hz) tcot IPDC COT transmit tone. Values: 1 = co1; 2 = co2 rcot: 1 tcot: 2 Command Modes Security level 2 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to configure IPDC COTs.
Chapter 9 Command Reference chipdccot Command Description lsipdc List IPDC Soft Switch configuration lsipdctimer List IPDC Timer Configuration chds1lnecho Configure DS1 line echo cancelling Cisco MGX 8260 Command Line Interface Guide Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference chipdcgwip chipdcgwip Change IPDC gateway IP and TCP port. chipdcgwip ip port Syntax Description ip The IP address of gateway for MSCP link. port The TCP Port number of gateway for MSCP link. This port number cannot be a well-known port number. Values: 1025 - 65535. Default: 5000 Defaults port: 5000 Command Modes Security level 2 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to configure.
Chapter 9 Command Reference chipdcgwip Command Description lsipdctimer List IPDC Timer Configuration lsipdccot List IPDC COT Configuration Cisco MGX 8260 Command Line Interface Guide Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference chipdcmaxm chipdcmaxm Change IPDC maximum modules. chipdcmaxm num Syntax Description num Defaults num: 16 Command Modes Security level 2 Command History Release Modification 1.2 This command was first introduced. Maximum number of modules (slot cards) supported. Values: integer from 1 - 16 Usage Guidelines Use this command to set the maximum number of modules. Examples The following example sets the maximum number of modules to 10.
Chapter 9 Command Reference chipdcpssip chipdcpssip Change IP Device Control (IPDC) primary Soft Switch IP and TCP port. chipdcpssip ip port Syntax Description ip The primary Soft Switch IP address. port The primary Soft Switch TCP Port. This port number cannot be a well-known port number. Values: 1025 - 65535. Default: 5000 Defaults port: 5000 Command Modes Security level 2 Command History Release Modification 1.2 This command was first introduced.
Chapter 9 Command Reference chipdcpssip Command Description lsipdctimer List IPDC Timer Configuration lsipdccot List IPDC COT Configuration Cisco MGX 8260 Command Line Interface Guide 9-80 Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference chipdcssadm chipdcssadm Change IPDC administrative status. chipdcssadm primary secondary downtime Syntax Description primary The administrative status of link with the primary Soft Switch. Values: 1=down, disconnect the current call server 2=up, connect the current call server 3=graceful disconnect, disconnect the current call server after the time specified by downtime. (reserved for future use) secondary The administrative status of link with the secondary Soft Switch.
Chapter 9 Command Reference chipdcssbaynum chipdcssbaynum Change IPDC bay number. chipdcssbaynum num Syntax Description num Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.2 This command was first introduced. The number associated with gateway being controlled. A string of exactly 8 characters. Usage Guidelines Use this command to assign a bay number to the IPDC. Examples The following example configures the bay number.
Chapter 9 Command Reference chipdcsshlth chipdcsshlth Change IPDC health check. chipdcsshlth admp adms dntime Syntax Description Defaults admp Enable or disable the link health check for the primary Soft Switch.Values: 1=enable; 2=disable adms Enable or disable the link health check for the secondary Soft Switch. Values: 1=enable; 2=disable dntime The time to wait before disabling the link health check.
Chapter 9 Command Reference chipdcsshlth Command Description chipdctimer Change IPDC Timers chipdccot Change IPDC COTs chpseudoip Change pseudo IP address lsipdc List IPDC Soft Switch configuration lsipdctimer List IPDC Timer Configuration lsipdccot List IPDC COT Configuration Cisco MGX 8260 Command Line Interface Guide 9-84 Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference chipdcssid chipdcssid Change IPDC system Id. chipdcssid ID Syntax Description ID Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.2 This command was first introduced. Identifier of the gateway being controlled by IPDC protocol, a string from 0 to 24 characters. Usage Guidelines Use this command to configure the IPDC system identifier. Examples The following example configures the IPDC system Id to 15.
Chapter 9 Command Reference chipdcssnumfor chipdcssnumfor Change IPDC numbering format. chipdcssnumfor format Syntax Description format Defaults format: 1 Command Modes Security level 2 Command History Release Modification 1.2 This command was first introduced. The format that determines the Soft Switch interpretation of module, line, and channel numbers on an MGX 8260. Values: 1= 0-base; 2=1-base. Usage Guidelines Use this command to set the IPDC numbering format.
Chapter 9 Command Reference chipdcsssip chipdcsssip Change IPDC secondary Soft Switch IP and TCP port. chipdcsssip ip port Syntax Description ip The secondary Soft Switch IP address. port The secondary Soft Switch TCP port. This port number cannot be a well-known port number. Values: 1025 - 65535. Default: 5000 Defaults port: 5000 Command Modes Security level 2 Command History Release Modification 1.2 This command was first introduced.
Chapter 9 Command Reference chipdcsssip Command Description lsipdctimer List IPDC Timer Configuration lsipdccot List IPDC COT Configuration Cisco MGX 8260 Command Line Interface Guide 9-88 Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference chipdcsstype chipdcsstype Change IPDC system type. chipdcsstype type Syntax Description type Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.2 This command was first introduced. The string of exactly 9 characters that identifies the manufacturer and model of the MGX 8260 Media Gateway. Usage Guidelines Use this command to configure the IPDC system type.
Chapter 9 Command Reference chipdctimer chipdctimer Change IPDC timers and retry counters. chipdctimer ssConnRetryTimer ssConnRetryThr tcpConnRetrTimer nsupRtxTimer lnkActiveTimer maxTcpConnRetry maxNsupRetry Syntax Description Defaults ssConnRetryTimer Minimum connection retry interval for primary or secondary Soft Switch when the link is up. The connection interval doubles with every retry attempt until the ssConnRetryThr value is reached. Values: integer 2000 to15000 msec.
Chapter 9 Command Reference chipdctimer Examples The following example sets the IPDC time to a minimum value of 5000 and a.maximum of 20000.
Chapter 9 Command Reference chkey chkey Change file key. chkey key Syntax Description key Defaults No default behavior or values. Command Modes Security level 1 Command History Release Modification 1.0 This command was first introduced. Up to 6 alphanumeric characters Usage Guidelines Use this command to configure the tftp security key for uploading and downloading files to prevent unauthorized file transfers. Examples The following example changes the security key to 323bf.
Chapter 9 Command Reference chm13 chm13 Change DS1 to DS3 map. chm13 SrcDS3LineNum SrcDS1LineNum DestDS1SlotNum DestDS1LineNum Syntax Description SrcDS3LineNum The number of the source DS3 line. Values: 1 - 6. SrcDS1LineNum The number of the DS1 line, or starting DS1 line, within the DS3 line. Values: 1 - 28. DestDS1SlotNum The logical slot number for the destination NSC (Narrowband Service Card). DestDS1LineNum The number of the DS1, or starting DS1, in the NSC. Valid entries are 1 through 16.
Chapter 9 Command Reference chmgcpcore chmgcpcore Change MGCP core parameters. chmgcpcore RequestTimeOut RequestRetries AdminStatus RestartInProgMWD RestartDelay ResponseTimeout ConnectivityTimeout Syntax Description RequestTimeOut The time in milliseconds before retransmitting an unacknowledged message. Values: 1 - 100000. RequestRetries The maximum number of retries for a request that times out. Values: 0 15. AdminStatus The desired state of the protocol.
Chapter 9 Command Reference chmgcpcore Related Commands Command Description chmgcplocaladdr1 Change the MGCP local address for network 1 chmgcplocaladdr2 Change the MGCP local address for network 2 chpmgcpaddr Change the primary Media Gateway Controller addresses chsmgcpaddr Change the secondary Media Gateway Controller addresses lsmgcp List MGCP core parameters lsmgcpdef List MGCP default parameters lsmgcpstat List MGCP statistics Cisco MGX 8260 Command Line Interface Guide Release 1.
Chapter 9 Command Reference chmgcpdname chmgcpdname Change the node domain name. chmgcpdname DomainName Syntax Description DomainName Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.0 This command was first introduced. The domain name for this node. Value: 1-64 characters Usage Guidelines Use this command to define a domain name for the MGX 8260 chassis. The domain name is an alternative to IP addressing.
Chapter 9 Command Reference chmgcplocaladdr1 chmgcplocaladdr1 Change the local MGCP address for network 1. chmgcplocaladdr1 MgcpLocalAddressNet1 MgcpLocalPrimUDPPortNet1 Syntax Description MgcpLocalAddressNet1 The IP address of the Media Gateway interface for network 1. Specify the IP address in standard dot notation. Values: string. MgcpLocalPrimUDPPortNet1 The primary UDP port of the Media Gateway interface for network 1. Values: 1025..65535. Defaults No default behavior or values.
Chapter 9 Command Reference chmgcplocaladdr2 chmgcplocaladdr2 Change the MGCP local address for network 2. chmgcplocaladdr2 MgcpLocalAddressNet2 MgcpLocalPrimUDPPortNet2 Syntax Description MgcpLocalAddressNet2 The IP address of the Media Gateway interface for network 2. Specify the IP address in standard dot notation. MgcpLocalPrimUDPPortNet2 The primary UDP port of the Media Gateway interface for network 2. Values: 1025..65535. Defaults No default behavior or values.
Chapter 9 Command Reference chmpc chmpc Configure default MPC parameters. chmpc DefTypeNetwork DefPktnPeriod DefBandwidth DefEchoCancel DefSilenceSupp DefTypeOfService DefResourceRes DefCOTReceiveTone DefCOTTransmitTone Encoding Syntax Description DefTypeNetwork The type of network. 1=voIp 2=voAtm 3=local DefPktnPeriod Packetization period in milliseconds. Value: fixed at 10 DefBandwidth The network bandwidth in kbps. Values: 8 and 64 kbps DefEchoCancel Enables or disables echo cancellation.
Chapter 9 Command Reference chmpc Defaults DefTypeNetwork: 3 DefPktnPeriod: 10 DefBandwidth: 64 DefEchoCancel: 1 DefSilenceSupp: 1 DefTypeOfService: 2 DefResourceRes: 1 DefCOTReceiveTone: 1 DefCOTTransmitTone: 2 Command Modes Security level 2 Command History Release Modification 1.1 This command was first introduced. Usage Guidelines Use this command to configure default MPC parameters. Examples The following sets the network type to local.
Chapter 9 Command Reference chndinf chndinf Configure node information. chndinf RackNum NodeName NodeNum Syntax Description RackNum Shelf number for node. Values: 1 - 100. NodeName Alphanumeric identifier for node. Values: up to 15 characters NodeNum Numeric identifier for node. Values: Integer, 1 - 1000 Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.0 This command was first introduced.
Chapter 9 Command Reference chpclksrc chpclksrc Change primary clock source. chpclksrc SlotNum LineNum ClkSrcType CardType Syntax Description SlotNum Slot number of the clock source. Values: 1 to 16 LineNum Line number of clock source. Values: NSC DS1 lines: 1 to 16 BSC DS3 lines: 501 to 506 DMC DS3 lines: 1 to 6 SCC, OC3 type: 1 to 4 SCC, BITS type: 1 ClkSrcType Type of clock source, broadband, narrowband, external, or internal. Values: 1, 2, 3, and 4 respectively.
Chapter 9 Command Reference chpclksrc Related Commands Command Description chsclksrc Change secondary clock source swclk Switch clock lsclksrcs List all clock sources Cisco MGX 8260 Command Line Interface Guide Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference chpcs chpcs Configure primary control server. chpcs Address Interface Check Syntax Description Address Primary MCS address in dotted notation w.x.y.z. Interface Default tcp port number for primary MCS. Values: Integer > 1024. Check Enables or disables the MSCP health check. Values: 1 = enabled, 2 = disabled Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.0 This command was first introduced.
Chapter 9 Command Reference chpmgcpaddr chpmgcpaddr Change the primary Media Gateway Controller addresses. chpmgcpaddr MgcpPMGCAddressNet1 MgcpPMGCCfgUDPPortNet1 MgcpPMGCAddressNet2 MgcpPMGCCfgUDPPortNet2 Syntax Description MgcpPMGCAddressNet1 The IP address of the Primary Media Gateway Controller on network 1. Specify the IP address in standard dot notation. Values: string. MgcpPMGCCfgUDPPortNet1 The UDP port of the Media Gateway Controller on network 2. Values: 1025..65535.
Chapter 9 Command Reference chpmgcpaddr Related Commands Command Description chmgcplocaladdr1 Change the MGCP local address for network 1 chmgcplocaladdr2 Change the MGCP local address for network 2 chsmgcpaddr Change the secondary Media Gateway Controller addresses lsmgcp List MGCP core parameters lsmgcpdef List MGCP default parameters lsmgcpstat List MGCP statistics Cisco MGX 8260 Command Line Interface Guide 9-106 Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference chprotocol chprotocol Switch between MGCP and IPDC protocols. chprotocol protocol Syntax Description protocol Defaults protocol: 1 Command Modes Security level 2 Command History Release Modification 1.2 This command was first introduced. The call control protocol. Values: 1 = MGCP; 2 = IPDC Usage Guidelines The MGX 8260 Media Gateway supports two protocols for voice call control, MGCP and IPDC. Use this command to switch from one protocol to the other.
Chapter 9 Command Reference chpseudoip chpseudoip Change pseudo IP address for IPDC. chpseudoip [pseip] Syntax Description pseip Defaults No default behavior or values. Command Modes Security level Command History Release Modification 1.1 This command was first introduced. This IP address that is used to change IP address for IPDC. Usage Guidelines Use this command to configure a pseudo IP address that represents the four broadband ports.
Chapter 9 Command Reference chpseudoip Command Description lsipdctimer List IPDC Timer Configuration lsipdccot List IPDC COT Configuration Cisco MGX 8260 Command Line Interface Guide Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference chpwd chpwd Change password. chpwd Syntax Description This command has no arguments or keywords. Command Modes Security level 1-6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Examples Use this interactive command to change the password of an existing account. To use this command, you must first log onto the account you want to change. Generally, users change their own passwords with this command.
Chapter 9 Command Reference chqprf chqprf Change queue profile. chqprf Card Queue# Syntax Description Card The number of an SCC card. Queue# The ATM queue profile number. Values: 1 - 10. Defaults Queue#: 1 Command Modes Security level 2 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Specifies the ATM traffic queue profile for an entire SCC card. The MGX 8260 defines 10 profiles for different traffic types. Profile 1 is recommended.
Chapter 9 Command Reference chsclksrc chsclksrc Change secondary clock source. chsclksrc Slot Line ClkSrcType CardType Syntax Description Slot Slot number of the clock source. Line Line number of clock source. Type Type of clock source, broadband, narrowband, external, or internal. Values: 1, 2, 3, and 4 respectively. CardType Type of card, bits or OC3. Values 1 and 2, respectively. Defaults No default behavior or values.
Chapter 9 Command Reference chscs chscs Change secondary control server (reserved for future use). chscs Address Interface Check Syntax Description Address Secondary MCS IP address in dotted notation w.x.y.z Interface Secondary tcp port number for sending IP packets to the secondary MCS Check Enables or disables the MSCP health check. Values: 1 = enabled, 2 = disabled Defaults No default values or behavior. Command Modes Security level 2 Command History Release Modification 1.
Chapter 9 Command Reference chsmgcpaddr chsmgcpaddr Change the secondary Media Gateway Controller addresses. chsmgcpaddr MgcpSMGCAddressNet1 MgcpSMGCCfgUDPPortNet1 MgcpSMGCAddressNet2 MgcpSMGCCfgUDPPortNet2 Syntax Description MgcpSMGCAddressNet1 The IP address of the Secondary Media Gateway Controller on network 1. Specify the IP address in standard dot notation. Values: string. MgcpSMGCCfgUDPPortNet1 The UDP port of the Media Gateway Controller on network 1. Values: 1025..65535.
Chapter 9 Command Reference chsmgcpaddr Command Description chmgcplocaladdr1 Change the MGCP local address for network 1 chmgcplocaladdr2 Change the MGCP local address for network 2 chpmgcpaddr Change the primary Media Gateway Controller addresses lsmgcp List MGCP core parameters lsmgcpdef List MGCP default parameters lsmgcpstat List MGCP statistics Cisco MGX 8260 Command Line Interface Guide Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference chsonetalm chsonetalm Change SONET alarm thresholds.
Chapter 9 Command Reference chsonetalm PCV15MinThresh PCV24HrThresh PES15MinThresh PES24HrThresh PSES15MinThresh PSES24HrThresh PUAS15MinThresh PUAS24HrThresh Defaults The path threshold for code violations in a 15-minute or sliding 24-hour window. Code violations are Bit Interleaved Parity errors detected in the incoming signal. The path threshold for errored seconds in a 15-minute or sliding 24-hour window.
Chapter 9 Command Reference chsonetalm PUAS15MinThresh: 12 PUAS24HrThresh: 120 Command Modes Security level 3 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to enable and configure alarm thresholds for SONET lines. When a counter exceeds a threshold, the system raises the performance alarm. Examples The following example changes the threshold for code violations in a 15-minute window: chsonetalm 9.
Chapter 9 Command Reference chsonetexptrace chsonetexptrace Change expected path trace parameters for SONET lines. chsonetexptrace Location [numOfLines expTraceIdLen expTraceId expTraceIdPosition] Syntax Description Location The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 numOfLines The number of lines to add. Values: 1-4.
Chapter 9 Command Reference chsonetexptrace Examples The following example defines an expected trace identifier of hello world in a 64-byte message for line 1 of slot 9: chsonetexptrace 9.
Chapter 9 Command Reference chsonetln chsonetln Change SONET lines. chsonetln Location [numOfLines MediumType FrameType LoopConfig HCSmasking PayloadScrambling FrameScrambling TxClockSource AdminStatus] Syntax Description Location The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 numOfLines The number of lines to add. Values: 1-4.
Chapter 9 Command Reference chsonetln Command History Usage Guidelines Release Modification 1.2 This command was first introduced. Use this command to change the configuration of SONET/SDH interfaces on the OC-3 SCC and back card. Although the SCC may occupy physical slots 9 or 10, you always configure logical slot 9. This command only applies to the OC-3 SCC. You can change a single line or a range of lines with this command.
Chapter 9 Command Reference chsonetperdi chsonetperdi Change extended rdi parameters for SONET paths. chsonetperdi Location [numOfLines SupportPathERDI SignalLabel ExpectedSignalLabel] Syntax Description Location The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 numOfLines The number of lines to add. Values: 1-4.
Chapter 9 Command Reference chsonetperdi Related Commands Command Description chsonettrace Change SONET trace parameters chsonetexptrace Change SONET expected trace parameters lssonetlnerdi List E-RDI information for a SONET line lssonetlnerdis List summary E-RDI information for all SONET lines Cisco MGX 8260 Command Line Interface Guide 9-124 Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference chsonettrace chsonettrace Change path trace parameters for SONET lines. chsonettrace Location [numOfLines TraceIdLen TraceId TraceIdPosition] Syntax Description Location The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 numOfLines The number of lines to add. Values: 1-4.
Chapter 9 Command Reference chsonettrace Related Commands Command Description chsonetperdi Change SONET path e-rdi parameters chsonetexptrace Change SONET expected trace parameters lssonetlnerdi List E-RDI information for a SONET line lssonetlnerdis List summary E-RDI information for all SONET lines Cisco MGX 8260 Command Line Interface Guide 9-126 Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference chsysip1 chsysip1 Change system IP address 1. chsysip1 Address Mask Syntax Description Address An IP1 address of the management interface in dotted notation w.x.y.z. Mask A subnet mask in dotted notation a.b.c.d. Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.0 This command was first introduced.
Chapter 9 Command Reference chsysip2 chsysip2 Change system IP address 2. chsysip2 Address Mask Syntax Description Address An IP2 address of the management interface in dotted notation w.x.y.z. Mask A subnet mask in dotted notation a.b.c.d. Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.0 This command was first introduced.
Chapter 9 Command Reference chsyslnmd chsyslnmd Change the line mode to T1 or E1. chsyslnmd Mode Syntax Description Mode The line mode for the chassis. Values: 1=T1 2=E1 Defaults No default behavior or values for this command. The default mode for a new chassis is T1. Command Modes Security level 1 Command History Release Modification 1.2 This command was first introduced.
Chapter 9 Command Reference chtime chtime Change time. chtime H:M:S [Zone] Syntax Description H:M:S The system time in hours, minutes, and seconds delimited by colons. Values: 0-23 for hours and 0-60 for minutes and seconds. Zone An integer from 1 to 25, representing a zone. Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.0 This command was first introduced.
Chapter 9 Command Reference chtime Examples The following example sets the system time to noon, Eastern Standard Time. chtime 12:00:00 18 Related Commands Command Description chdate Change system date chtimezn Change system time zone lsdate List date Cisco MGX 8260 Command Line Interface Guide Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference chtimezn chtimezn Change system time zone. chtimezn number Syntax Description number Defaults No default behavior or values. Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced. The Time Zone where this MGX 8260 node is installed. Values: 1 - 25 Usage Guidelines Use this command to change the system time zone.
Chapter 9 Command Reference chtmgr chtmgr Change trap manager. chtmgr Addr Port Interface Com_String Bitmap Syntax Description Addr The address of the SNMP manager who wants to receive trap events. Port Port to which the traps are transmitted. Interface The default interface for initially sending traps if the routing table has no trap manager. Values: 1 = scc-eth-if, the default system Ethernet management interface on SCC. 2 = inband-if, the in-band management interface.
Chapter 9 Command Reference chtmgr Defaults Port: 162 Interface: 1 Com_String: “public” Bitmap: 0 Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Network administrators can receive email for up to 20 traps. Use this command to change a manager’s SNMP trap registrations. Examples The following example changes the manager at address 10.1.1.10 and udp port 162 to receive events for the traps specified by bitmap 1100110.
Chapter 9 Command Reference chvport chvport Configure voice port. chvport SlotNum PortNum RepitionNum WrapNum [Dejitter DejitteBufLen Maxdj Mindj PacketLoading EchoTail] Syntax Description SlotNum The logical slot number of an NSC. Values: 1 to 16 PortNum The logical port number. Values 1 to 512 ReptitionNum The number of ports to add. Values: 1 to 6944. This corresponds to 31 ports per line, 16 lines per NSC, and 14 NSCs. WrapNum The DS0 number at which to wrap to the next slot.
Chapter 9 Command Reference chvport Command History Release Modification 1.0 This command was first introduced. 1.2 Added repetition and wrap numbers Usage Guidelines Use this command to configure one or more voice ports. Examples The following example disables the dejitter buffer for 4 lines starting slot 1 port 1. chvport 1 1 # 384 1 The system changes the packet loading for logical port one in slot one to 20 msec.
Chapter 9 Command Reference clralmhist clralmhist Clear alarm history. clralmhist Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 4 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to delete alarm history. Examples The following example clears the alarm history.
Chapter 9 Command Reference clrcdcnf clrcdcnf Clear configuration of a card. clrcdcnf Num Syntax Description Num Defaults No default behavior or values. Command Modes Security level 1 Command History Release Modification 1.0 This command was first introduced. The slot number of the card Usage Guidelines Clears the configuration of the specified card and resets it. Examples The following example clears the configuration of the card in slot 3.
Chapter 9 Command Reference clrds1lnst clrds1lnst Clear T1 line statistics. clrds1lnst Location Stat Syntax Description Location The slot and line number, delimited by a period, of the DS1 line. Stat The statistic to clear: Values: one of the following integers. 1=No Action. 2=Clear all the counters in the ds1Stats Table and dsx1StatsPerfAlarmState. 3=Clear LCV 15 Minute counter in the dsx1CurrentTable. 4=Clear LCV 24 Hour counter in the dsx1TotalTable.
Chapter 9 Command Reference clrds1lnst Command Modes Security level 4 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to clear the specified DS1 real-time statistic. Examples The following example clears the LCV 24 Hour counter in the dsx1TotalTablefor the DS1 line at slot 1 line 1. clrds1lnst 1.
Chapter 9 Command Reference clrds3lnst clrds3lnst Clear statistics for DS3 line. clrds3lnst Index stats Syntax Description Index The slot and line number, delimited by a period, of the DS3 line. Valid slot numbers: BSC: 11-16 DMC: 7 or 8 (reserved for future use) Valid line numbers: BSC: 501-506 DMC: 1-6 (reserved for future use) stats The instruction to clear or not to clear statistics. 1=Do not clear. 2=Clear Defaults No default behavior or values.
Chapter 9 Command Reference clrds3lnst Command Description lsds3lns List DS3 lines lsds3totst List DS3 total statistics Cisco MGX 8260 Command Line Interface Guide 9-142 Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference clre1lnst clre1lnst Clear E1 line statistics. clrds1lnst Location Stat Syntax Description Location The slot and line number, delimited by a period, of the line. Stat The statistic to clear: Values: one of the following integers. 1=No Action.
Chapter 9 Command Reference clre1lnst Stat Cont. 31=Clear PCV in e1CurrentTable 32=Clear PCV in e1TotalTable 33=Clear Control Slip seconds in e1CurrentTable 34=Clear Control Slip seconds in e1TotalTable 35=Clear all counters in e1CurrentTable 36=Clear all counters in e1TotalTable Defaults No default behavior or values. Command Modes Security level 4 Command History Release Modification 1.0 This command was first introduced.
Chapter 9 Command Reference clrevt clrevt Clear event log. clrevt Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to clear the event log. Examples The following example clears the event log.
Chapter 9 Command Reference clrndcnf clrndcnf Clear node configuration and restore defaults. clrndcnf Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 1 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to clear configuration of a node and restore the default settings. Use with caution because this interrupts service and changes many parameters.
Chapter 9 Command Reference clrslinecst clrslinecst Clear current statistics for a SONET line. clrslinecst Location [Stat] Syntax Description Location The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 Stat The statistic to clear: Values: one of the following integers: 1=No Action 2=All 3=ES 4=SES 5=CV 6=UAS Defaults Stat: 1 Command Modes Security level 4 Command History Release Modification 1.2 This command was first introduced.
Chapter 9 Command Reference clrslinetst clrslinetst Clear total statistics for a SONET line. clrslinetst Location [Stat] Syntax Description Location The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 Stat The statistic to clear: Values: one of the following integers: 1=No Action 2=All 3=ES 4=SES 5=CV 6=UAS Defaults Stat: 1 Command Modes Security level 4 Command History Release Modification 1.2 This command was first introduced.
Chapter 9 Command Reference clrsonetstats clrsonetstats Clear the SONET alarm statistics. clrspathtst Location [Stat] Syntax Description Location The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9.
Chapter 9 Command Reference clrsonetstats Defaults Stat: 1 Command Modes Security level 4 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to clear the specified alarm statistic. Examples The following example clears all SONET alarm counters at slot 9 line 1. clrsonetstats 9.
Chapter 9 Command Reference clrspathcst clrspathcst Clear current statistics for a SONET path. clrspathcst Location [Stat] Syntax Description Location The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 Stat The statistic to clear: Values: one of the following integers: 1=No Action 2=All 3=ES 4=SES 5=CV 6=UAS Defaults Stat: 1 Command Modes Security level 4 Command History Release Modification 1.2 This command was first introduced.
Chapter 9 Command Reference clrspathtst clrspathtst Clear total statistics for a SONET path. clrspathtst Location [Stat] Syntax Description Location The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 Stat The statistic to clear: Values: one of the following integers: 1=No Action 2=All 3=ES 4=SES 5=CV 6=UAS Defaults Stat: 1 Command Modes Security level 4 Command History Release Modification 1.2 This command was first introduced.
Chapter 9 Command Reference clrssectioncst clrssectioncst Clear current statistics for a SONET section. clrssectioncst Location [Stat] Syntax Description Location The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 Stat The statistic to clear: Values: one of the following integers: 1=No Action 2=All 3=ES 4=SES 5=SEFS 6=CV Defaults Stat: 1 Command Modes Security level 4 Command History Release Modification 1.2 This command was first introduced.
Chapter 9 Command Reference clrssectiontst clrssectiontst Clear total statistics for a SONET section. clrssectiontst Location [Stat] Syntax Description Location The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 Stat The statistic to clear: Values: one of the following integers: 1=No Action 2=All 3=ES 4=SES 5=SEFS 6=CV Defaults Stat: 1 Command Modes Security level 4 Command History Release Modification 1.2 This command was first introduced.
Chapter 9 Command Reference clrtraps clrtraps Clear the trap log. clrtraps Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to clear the log of SNMP traps. Examples The following example clears the trap log.
Chapter 9 Command Reference dbbkup dbbkup Back up the configuration database. dbbkup Syntax Description The command has no arguments or keywords. Defaults The system defines a backup file name. Command Modes Security level 1 Command History Release Modification 1.1 This command was first introduced. Usage Guidelines Use this command to save all configuration information, such as system and line settings, to the hard drive on the SCC.
Chapter 9 Command Reference dbrstr dbrstr Restore the configuration database. dbrstr fileName Syntax Description fileName Defaults No default behavior or values. Command Modes Security level 1 Command History Release Modification 1.1 This command was first introduced. The name of the backup file, without the .cfg extension. Usage Guidelines Use this command to restore the configuration information saved by dbbkup. Use the file name assigned by dbbkup, but omit the .cfg extension.
Chapter 9 Command Reference deacannfile deacannfile Deactivate an announcement file. deacannfile fid Syntax Description fid Defaults No default behavior or values. Command Modes Security level 3 Command History Release Modification 1.2 This command was first introduced. The announcement file ID. Values: 1-100 Usage Guidelines You use this command to deactivate an announcement file. Before attempting to remove an announcement file, first deactivate the file; otherwise, removal fails.
Chapter 9 Command Reference delcms delcms Delete community string. delcms Comm_Str Addr Syntax Description Comm_Str An SNMP community string, up to 20 characters. Addr The IP address of the SNMP manager who wants to discontinue receiving trap events Defaults No default behavior or values. Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced.
Chapter 9 Command Reference deldchan deldchan Delete a D Channel. deldchan Index Repetitions Syntax Description Index The slot and line number, delimited by a period, of the D channel Repetitions The number of sequential D Channels to delete. Values: 1 to 1136. Defaults Repetitions: 1 Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced. 1.
Chapter 9 Command Reference deldlsp deldlsp Delete a DLSAP profile. deldlsp Index Syntax Description Index Defaults No default behavior or values. Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced. The identifier of a DLSAP Profile. Values: 1 - 10. Usage Guidelines Use this command to deletes a DLSAP profile from the MGX 8260 Media Gateway. Profiles used by existing D Channels should not be deleted.
Chapter 9 Command Reference delds1ln delds1ln Delete DS1(T1 or E1) lines. delds1ln Index Numlines Syntax Description Index The slot and line number, delimited by a period, of the DS1 line. For example, enter slot 3 line 2 as 3.2. Valid slot numbers: • NSC: 1-8 and 11-16 • BSC: 11-16 Valid line numbers: • NSC: 1-16 • BSC: 1-168 as shown by the following table of DS1 to DS3 mappings.
Chapter 9 Command Reference delds1ln Examples The following example deletes 3 DS1 lines beginning at line 6 from slot 13: delds1ln 13.
Chapter 9 Command Reference delds3ln delds3ln Delete a DS3 line. delds3ln Index Numlines Syntax Description Index The slot and line number, delimited by a period, of the DS3 line. Valid slot numbers: BSC: 11-16 DMC: 7 or 8 (reserved for future use) Valid line numbers: BSC: 501-506 DMC: 1-6 (reserved for future use) Numlines Number of lines to delete. Defaults Numlines: 1 Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced. 1.
Chapter 9 Command Reference delds3ln Command Description lsds3curst List DS3 current statistics lsds3intst List DS3 interval statistics lsds3ln List DS3 line lsds3lns List DS3 lines lsds3totst List DS3 total statistics Cisco MGX 8260 Command Line Interface Guide Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference delereg delereg Delete email registration. delereg Index Syntax Description Index Defaults No default behavior or values. Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced. Position of the email address in the SnmpEmailRegTable. Values: integer. Usage Guidelines Use this command to stop email notifications to the user.
Chapter 9 Command Reference delethln delethln Delete Ethernet line. delethln Location Syntax Description Location Defaults No default values or behavior. Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced. The slot and line number, delimited by a period, of the Ethernet line. Values: The slot number of the SCC, either 9 or 10; the Fast Ethernet line number, from 1 to 4.
Chapter 9 Command Reference deliproute deliproute Delete an IP route. deliproute IPRouteDest Syntax Description IPRouteDest Defaults No default behavior or values. Command Modes Security level 3 Command History Release Modification 1.2 This command was first introduced. The destination IP address of this route. An entry of 0.0.0.0 is considered a default route.
Chapter 9 Command Reference delm13 delm13 Delete DS1 to DS3 map. delm13 DS3Line DS1Line NumLines Syntax Description DS3Line The number of the source DS3 line. When deleting more than one DS1, the range may span additional DS3s. Values: 1 - 6 DS1Line The number of the DS1 line, or starting DS1 line, within the DS3 line. Values: 1 - 28 NumLines The number of map pairs to add. Values: 1 - 192, depending on the number of mappings in a contiguous sequence Defaults No default behavior or values.
Chapter 9 Command Reference delmacsapprof delmacsapprof Delete a MACSAP profile. delmacsapprof Index Syntax Description Index Defaults No default behavior or values. Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced. This object is the identifier of a MAC SAP. Values: 1 - 16. Usage Guidelines Use this command to delete a MACSAP profile from the MGX 8260 Media Gateway. Profiles used by existing D Channels should not be deleted.
Chapter 9 Command Reference delreds delreds Delete a card redundancy pair. delreds Slot1 Slot2 Syntax Description Slot1 Physical location of the primary card in the chassis. Valid settings: 1-8 and 11-16. Slot2 Physical location of the secondary card in the chassis. Valid settings: 1-8 and 11-16. Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.0 This command was first introduced.
Chapter 9 Command Reference delsess delsess Delete an MGCP session manager. delsess SessionSetId GroupId SessionId Syntax Description SessionSetId The index of the session set to which the group containing the session manager belongs. Values: 1-6. GroupId The index of the session group to which the session manager belongs. Values: 1 or 2. SessionId The index of this session. Values: 1 or 2 Defaults No default behavior or values.
Chapter 9 Command Reference delsgrp delsgrp Delete an MGCP session group delsgrp SessionSetId GroupId Repetitions Syntax Description SessionSetId The index of this session. Values: 1 or 2 GroupId The index of the session group to which the session manager belongs. Values: 1 or 2 Repetitions The number of groups to delete Defaults Repetitions: 1 Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced.
Chapter 9 Command Reference delsonetln delsonetln Delete SONET lines. delsonetln Location [numOfLines] Syntax Description Location The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 numOfLines The number of lines to delete. Values: 1-4. Defaults numOfLines: 1 Command Modes Security level 3 Command History Release Modification 1.2 This command was first introduced.
Chapter 9 Command Reference delsrt delsrt Delete a static route. delsrt Addr Location Syntax Description Addr An address in dotted notation w.x.y.z of the destination of an existing static route Location The slot and line number, delimited by a period, of the origin of the static route Defaults No default behavior or values. Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced.
Chapter 9 Command Reference delsset delsset Delete an MGCP session set. delsset SessionSetId Syntax Description SessionSetId Defaults No default behavior or values. Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced. The index of the session set to which the group containing the session manager belongs. Values: 1-6. Usage Guidelines Use this command to delete a session set.
Chapter 9 Command Reference deltmgr deltmgr Delete trap manager. deltmgr Addr Syntax Description Addr Defaults No default behavior or values. Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced. The address of the SNMP manager who wants to discontinue notification of trap events. Usage Guidelines Deletes a manager from the registered list to receive SNMP trap events.
Chapter 9 Command Reference delusp delusp Delete user profile. delusp Name Syntax Description Name Defaults No default behavior or values. Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced. The login name of a user Usage Guidelines Use this command to remove the profile of a user from the system. Examples The following example deletes a user profile for a user named booter.
Chapter 9 Command Reference delvport delvport Delete voice port delvport Slot Port RepetitionNum WrapNum Syntax Description Defaults Slot The logical slot number of an NSC Port The logical port number RepetitionNum The number of ports to add. Values: 1 to 6944. This corresponds to 31 ports per line, 16 lines per NSC, and 14 NSCs. WrapNum The DS0 number at which to wrap to the next slot. Set this to the maximum number of DS0s the NSC in your configuration.
Chapter 9 Command Reference dnethln dnethln Down Ethernet line. dnethln Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 4 Command History Release Modification 1.0 This command was first introduced. The slot and line number, delimited by a period, of the Ethernet line Usage Guidelines Deactivates an Ethernet interface.
Chapter 9 Command Reference exit exit Log out. exit Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Examples Type this command to log out from the MGX 8260 Media Gateway The following command logs out. exit Related Commands Command Description bye Logs out from the MGX 8260 Media Gateway. logout Logs out from the MGX 8260 Media Gateway.
Chapter 9 Command Reference help help Display command help. help [command] Syntax Description command Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. The command for which you want help. Usage Guidelines Use this command without an argument to list the commands available at your security level. To obtain usage information for a command, specify the command name as an argument.
Chapter 9 Command Reference htmlversion htmlversion Display the HTML version. htmlversion Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to display version information for WebViewer HTML files. Examples The following example displays the HTML version.
Chapter 9 Command Reference logout logout Logout of the MGX 8260 Media Gateway. logout Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to end the session with the MGX 8260 Media Gateway. Examples The following example logs out.
Chapter 9 Command Reference lsacp lsacp List information on an active call lsacp Slot Line ID Syntax Description Slot The physical source (slot number) of an active call. Values: 1-16. Line The physical source (line number) of an active call. Values: 1-16. ID The DS0 used by an active call. Values: 1-24. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced.
Chapter 9 Command Reference lsacps lsacps List all active calls by resource lsacps Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to lists active calls for all slots, lines, and DS0s. Output includes the log port, and packets received and transmitted.
Chapter 9 Command Reference lsact lsact List an active call by transaction ID. lsact ID Syntax Description ID Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. A unique identifier of an active call. Values: index number Usage Guidelines Use this command to list active call information for a specific transaction ID. The transaction ID is re-used after the current active call is torn down.
Chapter 9 Command Reference lsacts lsacts List all active call by transaction. lsacts Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Output includes the transaction number, the slot, line, and DS0 of the source, the log port, and the packets received and transmitted.
Chapter 9 Command Reference lsalms lsalms List alarms. lsalms Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Displays the status of all shelf alarms and card and software errors. For more information, see Monitoring Shelf Alarms, page 6-2. Examples The following example lists alarms.
Chapter 9 Command Reference lsannfile lsannfile List the given announcement file. lsannfile fid Syntax Description fid Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 4 Command History Release Modification 1.2 This command was first introduced. The announcement file ID. Values: 1-100 Usage Guidelines You use this command to list information about the given announcement file.
Chapter 9 Command Reference lsannfiles lsannfiles List all announcement files. lsannfiles Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 4 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines You use this command to list all announcement files. For more information, see Viewing Announcement Files, page 4-33. Examples The following command lists all announcement files.
Chapter 9 Command Reference lsbertds1 lsbertds1 List DS1 BERT results. lsbertds1 Location Syntax Description Location The slot and line number, delimited by a period, of the DS1 line. For example, enter slot 3 line 2 as 3.2. Valid slot numbers: • NSC: 1-8 and 11-16 • BSC: 11-16 Valid line numbers: • NSC: 1-16 • BSC: 1-168 as shown by the following table of DS1 to DS3 mappings.
Chapter 9 Command Reference lsbertds1 Related Commands Command Description offbertds1 Stop BERT on DS1 onbertds1 Start BERT on DS1 Cisco MGX 8260 Command Line Interface Guide Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference lscd lscd List card details. lscd CardNum Syntax Description CardNum Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. The card about which you want information. Values: 1-16.
Chapter 9 Command Reference lscds lscds List cards. lscds Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to list information on all cards. For more information, see Viewing Summary Information for Cards, page 3-7. Examples The following example lists information about all cards.
Chapter 9 Command Reference lsclksrcs lsclksrcs List all clock sources. lsclksrcs Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to display all clock sources. For more information, see Viewing Clock Parameters, page 2-13. Examples The following example lists clock sources.
Chapter 9 Command Reference lscms lscms List a community strings. lstmgr Index Syntax Description Index Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. The index number of the community string Usage Guidelines Displays information about the community string and SNMP manager IP address. For more information, see Assigning a tftp Security Key, page 2-6.
Chapter 9 Command Reference lscmss lscmss List trap managers. lscmss Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to display summary information about all community strings. For more information, see Assigning a tftp Security Key, page 2-6.
Chapter 9 Command Reference lsdate lsdate List system date, time, and time zone. lsdate Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 1 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to display the system time and date. For more information, see Viewing Node Parameters, page 2-6. Examples The following example displays node information.
Chapter 9 Command Reference lsdchan lsdchan List information about a D Channel. lsdchan Index Syntax Description Index Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. The slot and line number, delimited by a period, of the new D Channel. Usage Guidelines Use this command to list information about a D Channel, such as its frame length, DS0, retransmission count, and more.
Chapter 9 Command Reference lsdchans lsdchans List information about all D Channels. lsdchans Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to list information about all D Channels. For more information, see Viewing D Channels, page 5-26.
Chapter 9 Command Reference lsdlsapstat lsdlsapstat List statistics for a DLSAP. lsdlsapstat Index Syntax Description Index Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. The identifier of a DLSAP Profile. Values: 1 - 20.
Chapter 9 Command Reference lsdlsapstats lsdlsapstats List DLSAP statistics. lsdlsapstats Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to list summary DLSAP statistics. For more information, see Viewing DLSAP Statistics, page 5-24. Examples The following example lists DLSAP statistics.
Chapter 9 Command Reference lsdlsapstatus lsdlsapstatus List status for a DLSAP. lsdlsapstatus Location Syntax Description Location The slot and line number, delimited by a period, of the DS1 line. For example, enter slot 3 line 2 as 3.2. Valid slot numbers: • NSC: 1-8 and 11-16 • BSC: 11-16 Valid line numbers: • NSC: 1-16 • BSC: 1-168 as shown by the following table of DS1 to DS3 mappings.
Chapter 9 Command Reference lsdlsapstatus Related Commands Command Description deldlsp Delete a DLSAP profile lsdlsapstat List statistics for a DLSAP lsdlsapstats List DLSAP statistics lsdlsp List a DLSAP profile lsdlsps List DLSAP profiles Cisco MGX 8260 Command Line Interface Guide Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference lsdlsp lsdlsp List a DLSAP profile. lsdlsp Num Syntax Description Num Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. The DLSAP profile number associated with the D Channel. Values: 1-20. Usage Guidelines Use this command to list the DLSAP profile information, including frame length, window size, retranmission count, timer, modulo, DLC, and TEI information.
Chapter 9 Command Reference lsdlsps lsdlsps List summary DLSAP profile information. lsdlsps Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to list summary DLSAP information for all profiles. For more information, see Viewing DLSAP Profiles, page 5-22.
Chapter 9 Command Reference lsds0 lsds0 List a DS0 entry. lsds0 Num Syntax Description SlotNum SlotNum The slot number of the card with the DS1 line. Valid slot numbers: • NSC: 1-8 and 11-16 • BSC: 11-16 The DS1 line number with the DS0 channel. Valid line numbers: • NSC: 1-16 • BSC: 1-168 as shown by the following table of DS1 to DS3 mappings. DS3 Line Number DS0Num DS1 Line Number 501 1-28 502 29-56 503 57-84 504 85-112 505 113-140 506 141-168 The number of the DS0 channel.
Chapter 9 Command Reference lsds0s lsds0s List all DS0 entries. lsds0s Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to list all configured DS0. Examples The following example lists all DS0 entries. lsds0s Cisco MGX 8260 Command Line Interface Guide Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference lsds1alm lsds1alm List all alarm thresholds for a DS1 line. lsds1alm Location Syntax Description Location The slot and line number, delimited by a period, of the DS1 line. For example, enter slot 3 line 2 as 3.2. Valid slot numbers: • NSC: 1-8 and 11-16 • BSC: 11-16 Valid line numbers: • NSC: 1-16 • BSC: 1-168 as shown by the following table of DS1 to DS3 mappings.
Chapter 9 Command Reference lsds1curst lsds1curst List DS1 current statistics. lsds1cursts Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. The slot and line number, delimited by a period, of the DS1 line Usage Guidelines Use this command to display the performance statistics of the current 15-minute collection period for the specified DS1 line.
Chapter 9 Command Reference lsds1cursts lsds1cursts List DS1 current statistics. lsds1cursts Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to display the performance statistics of the current 15-minute collection period for all DS1 lines.
Chapter 9 Command Reference lsds1intst lsds1intst List DS1 interval statistics. lsds1intst Location Num Syntax Description Location The slot and line number, delimited by a period, of the DS1 line. For example, enter slot 3 line 2 as 3.2. Valid slot numbers: • NSC: 1-8 and 11-16 • BSC: 11-16 Valid line numbers: • NSC: 1-16 • BSC: 1-168 as shown by the following table of DS1 to DS3 mappings.
Chapter 9 Command Reference lsds1intst Related Commands Command Description addds1ln Add DS1 line chds1alm Change DS1 alarm severity and thresholds chds1ln Change DS1 line clrds1lnst Clear DS1 line statistics delds1ln Delete DS1 line lsbertds1 List DS1 BERT results lsds1alm List DS1 alarm thresholds lsds1curst List DS1 current statistics lsds1cursts List all DS1current statistics lsds1ln List DS1 line lsds1lns List DS1 lines lsds1lnst List DS1 line statistics lsds1totst List D
Chapter 9 Command Reference lsds1ln lsds1ln List DS1 line information. lsds1ln Location Syntax Description Location The slot and line number, delimited by a period, of the DS1 line. For example, enter slot 3 line 2 as 3.2. Valid slot numbers: • NSC: 1-8 and 11-16 • BSC: 11-16 Valid line numbers: • NSC: 1-16 • BSC: 1-168 as shown by the following table of DS1 to DS3 mappings.
Chapter 9 Command Reference lsds1ln Related Commands Command Description addds1ln Add DS1 line chds1alm Change DS1 alarm severity and thresholds chds1ln Change DS1 line clrds1lnst Clear DS1 line statistics delds1ln Delete DS1 line lsbertds1 List DS1 BERT results lsds1alm List DS1 alarm thresholds lsds1curst List DS1 current statistics lsds1cursts List all DS1current statistics lsds1intst List DS1 line interval statistics lsds1lns List DS1 lines lsds1lnst List DS1 line statistics
Chapter 9 Command Reference lsds1lns lsds1lns List all DS1 lines. lsds1lns Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to display the configuration and alarm information for all DS1 lines. For more information, see Viewing Summary DS1/E1 Information, page 4-6.
Chapter 9 Command Reference lsds1lnst lsds1lnst List DS1 line statistics. lsds1lnst Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. The slot and line number, delimited by a period, of the DS1 line. Usage Guidelines Use this command to display the real-time statistics of the specified DS1 line.
Chapter 9 Command Reference lsds1totst lsds1totst List DS1 total statistics. lsds1totst Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. The slot and line number, delimited by a period, of the DS1 line. Usage Guidelines Use this command to display the totals of performance statistics of the specified DS1 line gathered over the past 24 hours.
Chapter 9 Command Reference lsds1totst Command Description lsds1totsts List DS1 total statistics lslns List existing lines Cisco MGX 8260 Command Line Interface Guide 9-220 Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference lsds1totsts lsds1totsts List DS1 total statistics. lsds1totsts Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Displays totals of the performance statistics of the all DS1 lines over the past day. For more information, see Viewing Total T1 Statistics, page 7-2.
Chapter 9 Command Reference lsds3alm lsds3alm List DS3 alarm. lsds3alm Location Syntax Description Location The slot and line number, delimited by a period, of the DS3 line. Valid slot numbers: BSC: 11-16 DMC: 7 or 8 (reserved for future use) Valid line numbers: BSC: 501-506 DMC: 1-6 (reserved for future use) Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. 1.
Chapter 9 Command Reference lsds3alm Command Description lsds3lns List DS3 lines lsds3totst List DS3 total statistics Cisco MGX 8260 Command Line Interface Guide Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference lsds3curst lsds3curst List DS3 current statistics. lsds3curst Location Syntax Description Location The slot and line number, delimited by a period, of the DS3 line. Valid slot numbers: BSC: 11-16 DMC: 7 or 8 (reserved for future use) Valid line numbers: BSC: 501-506 DMC: 1-6 (reserved for future use) Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. 1.
Chapter 9 Command Reference lsds3curst Command Description lsds3intst List DS3 interval statistics lsds3lns List DS3 lines lsds3totst List DS3 total statistics Cisco MGX 8260 Command Line Interface Guide Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference lsds3cursts lsds3cursts List current statistics for all DS3 lines. lsds3cursts Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. 1.
Chapter 9 Command Reference lsds3intst lsds3intst List DS3 interval statistics. lsds3intst Location Num Syntax Description Location The slot and line number, delimited by a period, of the DS3 line.
Chapter 9 Command Reference lsds3intst Command Description delds3ln Delete DS3 line lsds3alm List DS3 alarm lsds3curst List current DS3 line statistics lsds3ln List DS3 line lsds3lns List DS3 lines lsds3totst List DS3 total statistics Cisco MGX 8260 Command Line Interface Guide 9-228 Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference lsds3ln lsds3ln List DS3 line and configuration. lsds3ln Location Syntax Description Location The slot and line number, delimited by a period, of the DS3 line. Valid slot numbers: BSC: 11-16 DMC: 7 or 8 (reserved for future use) Valid line numbers: BSC: 501-506 DMC: 1-6 (reserved for future use) Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. 1.
Chapter 9 Command Reference lsds3ln Command Description lsds3intst List DS3interval statistics lsds3lns List DS3 lines lsds3totst List DS3 total statistics Cisco MGX 8260 Command Line Interface Guide 9-230 Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference lsds3lns lsds3lns List DS3 lines. lsds3lns Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. 1.1 BSC card inclusion - no functional change Usage Guidelines Use this command to display the configuration information for all DS3 lines. For more information, see Viewing Summary DS3 Information, page 4-10.
Chapter 9 Command Reference lsds3lnst lsds3lnst List real-time statistics for a DS3 line. lsds3lnst Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. 1.
Chapter 9 Command Reference lsds3totst lsds3totst List DS3 total statistics. lsds3totst Location Syntax Description Location The slot and line number, delimited by a period, of the DS3 line. Valid slot numbers: BSC: 11-16 DMC: 7 or 8 (reserved for future use) Valid line numbers: BSC: 501-506 DMC: 1-6 (reserved for future use) Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. 1.
Chapter 9 Command Reference lsds3totst Command Description lsds3curst List current DS3 line statistics lsds3intst List DS3interval statistics lsds3lns List DS3 line lsds3ln List DS3 lines Cisco MGX 8260 Command Line Interface Guide 9-234 Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference lsdsps lsdsps List DSP multiservice modules. lsdsps Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to list all DSP multiservice modules (MSMs) and their operational status. For more information, see Viewing MSM Configuration and Status, page 3-7.
Chapter 9 Command Reference lsdurationif lsdurationif List duration information about announcement files. lsdurationif Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines You use this command to list the maximum, current, and available duration of announcement files.
Chapter 9 Command Reference lse1alm lse1alm List all alarm thresholds for a E1 line. lse1alm Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. The slot and line number, delimited by a period, of the line. Valid slots: 1-8 and 11-16. Valid lines: 1-16 Usage Guidelines Use this command to list E1 line alarm thresholds, such as Red, RAI, and Perf Alarm Severity.
Chapter 9 Command Reference lse1alrm lse1alrm List all alarms for a E1 line. lse1alrm Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. The slot and line number, delimited by a period, of the line. Valid slots: 1-8 and 11-16. Valid lines: 1-16 Usage Guidelines Use this command to list E1 line alarms, such as Red, RAI, and Perf Alarm Severity.
Chapter 9 Command Reference lse1curst lse1curst List current E1 current statistics. lse1curst Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. The slot and line number, delimited by a period, of the line. Valid slots: 1-8 and 11-16.
Chapter 9 Command Reference lse1cursts lse1cursts List all E1 current statistics. lse1curst Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to display all E1 performance statistics for the current 15-minute collection period. This command only applies to BSC lines.
Chapter 9 Command Reference lse1intst lse1intst List E1 interval statistics. lse1intst Location Num Syntax Description Location The slot and line number, delimited by a period, of the line. Valid slots: 1-8 and 11-16. Valid lines: 1-16 Num A number specifying an interval, where 1 is the most recently completed 15 minute interval and 96 is the oldest 15 minutes interval (assuming that all 96 intervals are valid). Values: 1-96. Defaults No default behavior or values.
Chapter 9 Command Reference lse1lnst lse1lnst List real-time E1 line statistics. lse1lnst Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. The slot and line number, delimited by a period, of the line. Valid slots: 1-8 and 11-16. Valid lines: 1-16 Usage Guidelines Use this command to display the real-time statistics and alarms for the specified E1 line.
Chapter 9 Command Reference lse1lnsts lse1lnsts List all real-time E1 line statistics. lse1lnsts Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to display the real-time statistics and alarms for the specified E1 line. This command only applies to BSC lines.
Chapter 9 Command Reference lse1perf15 lse1perf15 List 15-minute performance alarms for an E1 line. lse1perf15 Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. The slot and line number, delimited by a period, of the line. Valid slots: 1-8 and 11-16. Valid lines: 1-16 Usage Guidelines Use this command to display 15-minute performance alarms for an E1 line.
Chapter 9 Command Reference lse1perf24 lse1perf24 List 24-hour performance alarms for an E1 line. lse1perf24 Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. The slot and line number, delimited by a period, of the line. Valid slots: 1-8 and 11-16. Valid lines: 1-16 Usage Guidelines Use this command to display 24-hour performance alarms for an E1 line.
Chapter 9 Command Reference lse1totst lse1totst List total statistics. lse1totst Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. The slot and line number, delimited by a period, of the line. Valid slots: 1-8 and 11-16.
Chapter 9 Command Reference lse1totsts lse1totsts List total statistics for all E1 lines. lse1totsts Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to display performance statistics totals gathered over the past 24 hours for all lines. This command only applies to BSC lines.
Chapter 9 Command Reference lsem lsem List email server. lsem Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to list email server information and source email addresses. For more information, see Listing Email Server and Email Alert Registrations, page 6-26.
Chapter 9 Command Reference lsemm lsemm List sensor environmental monitoring data. lsemm UnitID SensorType SensorID Syntax Description UnitID The unit identifier: 1=slot1 2=slot2 3=slot3 4=slot4 5=slot5 6=slot6 7=slot7 8=slot8 9=slot9 10=slot10 11=slot11 12=slot12 13=slot13 14=slot14 15=slot15 16=slot16 100=chassis SensorType Temperature, fan, or voltage sensor. Values: 1 - 3, respectively. Fan (3) is valid only with the chassis unit ID (100).
Chapter 9 Command Reference lsemm Usage Guidelines Use this command to display the specified environmental measurement taken by a single sensor. Sensors measure the following conditions: temperature of the chassis, Switch Control Card (SCC) and Narrowband Service Card (NSC); the voltage of the chassis and all cards, SCC, NSC, and Distribution Matrix Card (DMC); the fan speed of the chassis.
Chapter 9 Command Reference lsemms lsemms List environmental monitoring sensors. lsemms Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced.
Chapter 9 Command Reference lsereg lsereg List entry registered. lsereg Index Syntax Description Index Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Position of the email address in the SnmpEmailRegTable. Values: integer. Usage Guidelines Lists an entry registered for email alerts. For more information, see Listing Email Server and Email Alert Registrations, page 6-26.
Chapter 9 Command Reference lseregs lseregs List registered email alerts. lseregs Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to display list all entries registered for email alerts. For more information, see Listing Email Server and Email Alert Registrations, page 6-26.
Chapter 9 Command Reference lsethln lsethln List Ethernet line. lsethln Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. The slot and line number, delimited by a period, of the Ethernet line. Valid slots: 9 or 10. Valid lines: 1-4. Usage Guidelines Use this command to display the configuration information for the Ethernet interface at the line specified.
Chapter 9 Command Reference lsethlns lsethlns List Ethernet lines. lsethlns Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to display the configuration information for all Ethernet interfaces. For more information, see Viewing Fast Ethernet Configuration and Status, page 4-14.
Chapter 9 Command Reference lsevt lsevt List event log. lsevt Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to display the date and time of the event, a description of the event, and active alarms. For more information, see Examples The following example lists the event log.
Chapter 9 Command Reference lssgrp lssgrp List information for an RUDP session group. lssgrp SetID GroupID Syntax Description SetID Session set identifier. Value: integer. GroupID Session group identifier. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines A session group consists of one or more RUDP sessions.
Chapter 9 Command Reference lssgrps lssgrps List detailed information for all RUDP session groups. lssgrps Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines A session group consists of one or more RUDP sessions. A session represents the ‘physical’ connection between the media gateway and media gateway controller.
Chapter 9 Command Reference lsgroupstat lsgroupstat List statistics for an RUDP session group. lsgroupstat Index Syntax Description Index Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Session group identifier. Use lsgroups to determine valid identifiers. Value: integer. Usage Guidelines A session group consists of or more RUDP sessions.
Chapter 9 Command Reference lsipdc lsipdc List IPDC Soft Switch configuration. lsipdc Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to list the IPDC Soft Switch configuration. For more information, see Viewing IPDC Settings, page 5-33.
Chapter 9 Command Reference lsipdccot lsipdccot List IPDC COT configuration. lsipdccot Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command list the IPDC COT configuration. For more information, see Viewing IPDC COT Information, page 5-36. Examples The following example lists the IPDC COT configuration.
Chapter 9 Command Reference lsipdctimer lsipdctimer List IPDC timer configuration. lsipdctimer Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to list the IPDC timer configuration. For more information, see Viewing IPDC Timer and Retry Counter Information, page 5-35.
Chapter 9 Command Reference lsiproute lsiproute List IP route lsiproute Dest Syntax Description Dest Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. The destination IP address of this route. An entry of 0.0.0.0 is considered a default route. Usage Guidelines Use this command to list an IP route. For more information, see Viewing IP Routes, page 2-10.
Chapter 9 Command Reference lsiproutes lsiproutes List IP routes lsiproutes Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to list the destination, gateway (next hop), interface index, and mask of IP routes. For more information, see Viewing IP Routes, page 2-10.
Chapter 9 Command Reference lskey lskey Display file key. lskey Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to display the tftp security key. This key authenticates users when uploading and downloading files. For more information, see Assigning a tftp Security Key, page 2-6.
Chapter 9 Command Reference lslapd lslapd List general LAPD information for a card. lslapd Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. The slot number of the card. Values: 9-16. Usage Guidelines Use this command to display the number of physical links, DLCs, DLCs per SAP, and ASP links. For more information, see Viewing LAPD Parameters, page 5-30.
Chapter 9 Command Reference lslapds lslapds List information about all LAPD cards. lslapds Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Displays the card number, physical links, number of DLCs, LD links, and ASP links. For more information, see Viewing LAPD Parameters, page 5-30.
Chapter 9 Command Reference lslgcd lslgcd List upgrade information. lslgcd upgdLogicalCardIndex Syntax Description upgdLogicalCardIndex Defaults No default behavior or values. Command Modes Security level 1 Command History Release Modification 1.1.3 This command was first introduced. The logical number of the card to upgrade. Values: 1-16. Usage Guidelines Use this command to list upgrade information for a card.
Chapter 9 Command Reference lslgcds lslgcds List upgrade information for all cards. lslgcd Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 1 Command History Release Modification 1.1.3 This command was first introduced. Usage Guidelines Use this command to list upgrade information for all cards.
Chapter 9 Command Reference lslns lslns List all lines. lslns Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to display the slot number, line number, and line type for each DS1, DS3, and Fast Ethernet line. For more information, see Viewing All MGX 8260 Lines, page 4-1.
Chapter 9 Command Reference lslns Command Description lsds1lns List DS1 lines lsds1lnst List DS1 line statistics lsds1totst List DS1 total statistics lsds1totsts List DS1 total statistics lsds3ln List DS3 line lsds3lns List DS3 lines Cisco MGX 8260 Command Line Interface Guide Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference lslogicalcarddchan lslogicalcarddchan List bulk D Channel usage for a card. lslogicalcarddchan Location Syntax Description Location The slot and line number, delimited by a period, of the DS1 line. For example, enter slot 3 line 2 as 3.2. Valid slot numbers: • NSC: 1-8 and 11-16 • BSC: 11-16 Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced.
Chapter 9 Command Reference lslogicalcarddchans lslogicalcarddchans List D Channel capacity for the chassis. lslogicalcarddchans Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to list bulk D Channel capacity. For more information, see Viewing D Channels, page 5-26.
Chapter 9 Command Reference lslogin lslogin List login information. lslogin Index Syntax Description Index Defaults No default behavior or values. Command Modes Security level 1 Command History Release Modification 1.2 This command was first introduced. The index number of the user account. Values: 1 - 20. Usage Guidelines Displays details about a current login, including the account name, source IP address, and the date and time the session started.
Chapter 9 Command Reference lslogins lslogins List all active logins. lslogins Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 1 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Displays information about all current logins, including the account names, source IP addresses, and the date and time the sessions started.
Chapter 9 Command Reference lsm13 lsm13 List DS3-to-DS1 mapping. lsm13 DS3Line DS1Line Syntax Description DS3Line The number of the source DS3 line. Values: 1 - 6. DS1Line The number of the DS1 line, or starting DS1 line, within the DS3 line. Values: 1 - 28. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Displays the DS3-to-DS1 mapping.
Chapter 9 Command Reference lsm13s lsm13s List DS3-to-DS1 mappings. lsm13s Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Displays all DS3-to-DS1 mapping. For more information, see Viewing Map Tables, page 4-13. Examples The following example displays all DS3-to-DS1 mapping.
Chapter 9 Command Reference lsmacsapprof lsmacsapprof List information about a MACSAP profile. lsmacsapprof Index Syntax Description Index Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. The identifier of a MAC SAP. Values: 1 - 16. Usage Guidelines Displays the interface, arbitration, LAPD type, and N202. For more information, see Viewing MACSAP Profiles, page 5-20.
Chapter 9 Command Reference lsmacsapprofs lsmacsapprofs List all MACSAP profiles. lsmacsapprofs Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to list summary information about MACSAP interfaces, including the MACSAP profile number, the interface, arbitration, LAPD type, and N202.
Chapter 9 Command Reference lsmacsapstat lsmacsapstat List statistics for a MACSAP interface. lsmacsapstat Index Syntax Description Index Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. The slot and line number, delimited by a period, of the MACSAP interface. Usage Guidelines Use this command to display received frames, transmitted frames, and received bytes for a MACSAP interface.
Chapter 9 Command Reference lsmacsapstats lsmacsapstats List MACSAP statistics for all interfaces. lsmacsapstats Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Displays statistics for MACSAP, including the location of each MACSAP, received frames, transmitted frames, and received bytes.
Chapter 9 Command Reference lsmgcp lsmgcp List MGCP core parameters. lsmgcp Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to display the MGCP protocol parameters. For more information, see Viewing MGCP Status Information, page 5-8. Examples The following example lists MGCP core parameters.
Chapter 9 Command Reference lsmgcpdef lsmgcpdef List MGCP default parameters. lsmgcpdef Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Displays the MGCP protocol default parameters. For more information, see Viewing MGCP Settings, page 5-5.
Chapter 9 Command Reference lsmgcpstat lsmgcpstat List MGCP statistics. lsmgcpstat Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to display statistics for the MGCP protocol stack. For more information, see Viewing MGCP Protocol Statistics, page 5-9.
Chapter 9 Command Reference lsmgcpvoice lsmgcpvoice List MGCP voice parameters lsmgcpvoice Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to display voice parameters for the MGCP protocol.
Chapter 9 Command Reference lsmgips lsmgips List management IP addresses. lsmgips Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to display all management IP addresses and related information. For more information, see Viewing Management Port Parameters, page 2-8.
Chapter 9 Command Reference lsmpc lsmpc List MPC parameters. lsmpc Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced.
Chapter 9 Command Reference lsmsms lsmsms List multiservice modules. lsmsms Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to list all multiservice modules (MSMs) and their operational status. For more information, see Viewing MSM Configuration and Status, page 3-7.
Chapter 9 Command Reference lsndinf lsndinf List node information. lsndinf Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to display the rack number for this node, the node name and number, and the type and serial number of the back plane. For more information, see Viewing Node Parameters, page 2-6.
Chapter 9 Command Reference lsports lsports List all ports. lsports Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to display information about all ports. Examples The following example displays information about ports. lsports Cisco MGX 8260 Command Line Interface Guide 9-290 Release 1.
Chapter 9 Command Reference lsreds lsreds List redundancy pairs. lsreds Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to display card redundancy pairs. For more information, see Viewing BSC and NSC Redundancy, page 3-15. Examples The following example lists card redundancy pairs.
Chapter 9 Command Reference lsrudpconnstats lsrudpconnstats List statistics for an RUDP connection. lsrudpconnstats ID Syntax Description ID Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. RUDP session identifier. Value: integer Usage Guidelines The communications link between the media gateway and media gateway controller uses a Reliable UDP connection.
Chapter 9 Command Reference lsrudpgblstats lsrudpgblstats List global statistics for RUDP lsrudpgblstats Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines The communications link between the media gateway and media gateway controller uses Reliable UDP connections.
Chapter 9 Command Reference lsrudptxstats lsrudptxstats List RUDP transport statistics. lsrudptxstats SessionSetId GroupId SessionId Syntax Description SessionSetId The index of the session set to which the group containing the session manager belongs. Values: 1-6. GroupId The index of the session group to which the session manager belongs. Values: 1 or 2. SessionId The index of this session. Values: 1 or 2 Defaults No default behavior or values.
Chapter 9 Command Reference lssession lssession List RUDP session information. lssession SetID GroupID SessionID Syntax Description SetID The session set identifier. Use lssessions to determine valid identifiers. Value: integer. GroupID The session group identifier. Value: integer. SessionID The session identifier. Value: integer Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced.
Chapter 9 Command Reference lssessions lssessions List all RUDP sessions. lssessions Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines A session represents a ‘physical’ connection between the media gateway and media gateway controller. This command lists summary information for a all RUDP sessions.
Chapter 9 Command Reference lssessstats lssessstats List session statistics. lssessstats SessionSetId GroupId SessionId Syntax Description SessionSetId The index of the session set to which the group containing the session manager belongs. Values: 1-6. GroupId The index of the session group to which the session manager belongs. Values: 1 or 2. SessionId The index of this session. Values: 1 or 2 Defaults No default behavior or values.
Chapter 9 Command Reference lssessstatslr lssessstatslr List session statistics since last reset. lssessstatslr SessionSetId GroupId SessionId Syntax Description SessionSetId The index of the session set to which the group containing the session manager belongs. Values: 1-6. GroupId The index of the session group to which the session manager belongs. Values: 1 or 2. SessionId The index of this session. Values: 1 or 2 Syntax Description The command has no arguments or keywords.
Chapter 9 Command Reference lsset lsset List RUDP session set information. lsset Index Syntax Description Index Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. The session set identifier. Use lssets to determine valid identifiers. Value: integer 1-6. Usage Guidelines A session set is a collection of session groups, each connecting to a different media gateway controller.
Chapter 9 Command Reference lssets lssets List all RUDP session sets. lssets Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines A session set is a collection of session groups, each connecting to a different media gateway controller. Use session sets for redundant media gateway controller architectures.
Chapter 9 Command Reference lsslinecst lsslinecst List current statistics for a SONET line. lsslinecst Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 Usage Guidelines Use this command to display current ES, SES, CV, and UAS statistics for a SONET line.
Chapter 9 Command Reference lsslinecst Command Description lsslinetst List total statistics for a SONET line lsslinetsts List total statistics for all SONET lines lsslineist List interval statistics for a SONET line lsslineists List interval statistics for all SONET lines lsspathcst List current statistics for a SONET path lsspathcsts List current statistics for all SONET paths lsspathtst List total statistics for a SONET path lsspathtsts List total statistics for all SONET paths lsspat
Chapter 9 Command Reference lsslinecsts lsslinecsts List current statistics for all SONET lines. lsslinecsts Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to display current ES, SES, CV, and UAS statistics for all SONET lines. For more information, see Viewing Line Current Statistics, page 7-17.
Chapter 9 Command Reference lsslinecsts Command Description lsspathcsts List current statistics for all SONET paths lsspathtst List total statistics for a SONET path lsspathtsts List total statistics for all SONET paths lsspathist List interval statistics for a SONET path lsspathists List interval statistics for all SONET paths lssonetstat List alarm statistics for an OC-3 line lssonetstats List alarm statistics for all OC-3 lines Cisco MGX 8260 Command Line Interface Guide 9-304 Releas
Chapter 9 Command Reference lsslineist lsslineist List interval statistics for a SONET line. lsslineist Location Interval Syntax Description Location The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 Interval The measurement interval of interest. Values: 1-96, where 1 is the most recent interval Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced.
Chapter 9 Command Reference lsslineist Command Description lsssectionists List interval statistics for all SONET sections lsslinecst List current statistics for a SONET line lsslinecsts List current statistics for all SONET lines lsslinetst List total statistics for a SONET line lsslinetsts List total statistics for all SONET lines lsslineists List interval statistics for all SONET lines lsspathcst List current statistics for a SONET path lsspathcsts List current statistics for all SONET
Chapter 9 Command Reference lsslineists lsslineists List interval statistics for all SONET lines. lsslineists Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to display interval ES, SES, CV, and UAS statistics for all SONET lines. For more information, see Viewing Line Interval Statistics, page 7-18.
Chapter 9 Command Reference lsslineists Command Description lsspathcsts List current statistics for all SONET paths lsspathtst List total statistics for a SONET path lsspathtsts List total statistics for all SONET paths lsspathist List interval statistics for a SONET path lsspathists List interval statistics for all SONET paths lssonetstat List alarm statistics for an OC-3 line lssonetstats List alarm statistics for all OC-3 lines Cisco MGX 8260 Command Line Interface Guide 9-308 Releas
Chapter 9 Command Reference lsslinetst lsslinetst List total statistics for a SONET line. lsslinetst Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 Usage Guidelines Use this command to display total ES, SES, CV, and UAS statistics for a SONET line.
Chapter 9 Command Reference lsslinetst Command Description lsslinecsts List current statistics for all SONET lines lsslinetsts List total statistics for all SONET lines lsslineist List interval statistics for a SONET line lsslineists List interval statistics for all SONET lines lsspathcst List current statistics for a SONET path lsspathcsts List current statistics for all SONET paths lsspathtst List total statistics for a SONET path lsspathtsts List total statistics for all SONET paths
Chapter 9 Command Reference lsslinetsts lsslinetsts List total statistics for all SONET lines. lsslinetsts Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to display total ES, SES, CV, and UAS statistics for all SONET lines. For more information, see Viewing Line Total Statistics, page 7-18.
Chapter 9 Command Reference lsslinetsts Command Description lsspathtst List total statistics for a SONET path lsspathtsts List total statistics for all SONET paths lsspathist List interval statistics for a SONET path lsspathists List interval statistics for all SONET paths lssonetstat List alarm statistics for an OC-3 line lssonetstats List alarm statistics for all OC-3 lines Cisco MGX 8260 Command Line Interface Guide 9-312 Release 1.2, Part Number 78-10987-01 Rev.
Chapter 9 Command Reference lssonetalm lssonetalm List SONET alarm thresholds. lssonetalm Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. The slot and line number, delimited by a period, of the SONET line. Valid slot: 9. Valid lines: 1-4 Usage Guidelines Use this command to display SONET alarm thresholds.
Chapter 9 Command Reference lssonetalms lssonetalms List SONET alarms. lssonetalms Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to display to view red, yellow, and performance alarms for SONET lines. For more information, see Viewing OC-3 Alarms, page 6-15.
Chapter 9 Command Reference lssonetln lssonetln List SONET line. lssonetln Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 Usage Guidelines Use this command to display the status and configuration information for the specified SONET line.
Chapter 9 Command Reference lssonetlns lssonetlns List SONET lines. lssonetlns Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to display status and configuration information for all SONET lines.
Chapter 9 Command Reference lssonetlnerdi lssonetlnerdi List SONET line extended remote defect indication. lssonetlnerdi Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9.
Chapter 9 Command Reference lssonetlnerdis lssonetlnerdis List E-RDI information for all lines. lssonetlnerdis Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to display E-RDI information for all SONET lines. For more information, see Viewing E-RDI Configuration and Status, page 4-22.
Chapter 9 Command Reference lssonetstat lssonetstat List SONET alarm statistics. lssonetstat Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 Usage Guidelines Use this command to display SONET alarm statistics.
Chapter 9 Command Reference lssonetstat Command Description lsslinecsts List current statistics for all SONET lines lsslinetst List total statistics for a SONET line lsslinetsts List total statistics for all SONET lines lsslineist List interval statistics for a SONET line lsslineists List interval statistics for all SONET lines lsspathcst List current statistics for a SONET path lsspathcsts List current statistics for all SONET paths lsspathtst List total statistics for a SONET path lss
Chapter 9 Command Reference lssonetstats lssonetstats List all SONET alarm statistics. lssonetstats Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to display all SONET alarm statistics and states. For more information, see Monitoring SONET Alarm Statistics, page 7-23.
Chapter 9 Command Reference lssonetstats Command Description lsspathcst List current statistics for a SONET path lsspathcsts List current statistics for all SONET paths lsspathtst List total statistics for a SONET path lsspathtsts List total statistics for all SONET paths lsspathist List interval statistics for a SONET path lsspathists List interval statistics for all SONET paths lssonetstat List alarm statistics for an OC-3 line lssonetstats List alarm statistics for all OC-3 lines Cis
Chapter 9 Command Reference lsspathcst lsspathcst List current statistics for a SONET path. lsspathcst Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 Usage Guidelines Use this command to display current ES, SES, CV, and UAS statistics for a SONET path.
Chapter 9 Command Reference lsspathcst Command Description lsslinecsts List current statistics for all SONET lines lsslinetst List total statistics for a SONET line lsslinetsts List total statistics for all SONET lines lsslineist List interval statistics for a SONET line lsslineists List interval statistics for all SONET lines lsspathcsts List current statistics for all SONET paths lsspathtst List total statistics for a SONET path lsspathtsts List total statistics for all SONET paths ls
Chapter 9 Command Reference lsspathcsts lsspathcsts List current statistics for all SONET paths. lsspathcsts Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to display current ES, SES, CV, and UAS statistics for all SONET paths. For more information, see Viewing Path Current Statistics, page 7-20.
Chapter 9 Command Reference lsspathcsts Command Description lsspathcst List current statistics for a SONET path lsspathtst List total statistics for a SONET path lsspathtsts List total statistics for all SONET paths lsspathist List interval statistics for a SONET path lsspathists List interval statistics for all SONET paths lssonetstat List alarm statistics for an OC-3 line lssonetstats List alarm statistics for all OC-3 lines Cisco MGX 8260 Command Line Interface Guide 9-326 Release 1.
Chapter 9 Command Reference lsspathist lsspathist List interval statistics for a SONET path. lsspathist Location Interval Syntax Description Location The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 Interval The measurement interval of interest. Values: 1-96, where 1 is the most recent interval Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced.
Chapter 9 Command Reference lsspathist Command Description lsssectionists List interval statistics for all SONET sections lsslinecst List current statistics for a SONET line lsslinecsts List current statistics for all SONET lines lsslinetst List total statistics for a SONET line lsslinetsts List total statistics for all SONET lines lsslineist List interval statistics for a SONET line lsslineists List interval statistics for all SONET lines lsspathcst List current statistics for a SONET p
Chapter 9 Command Reference lsspathists lsspathists List interval statistics for all SONET paths. lsspathists Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to display interval ES, SES, CV, and UAS statistics for all SONET paths. For more information, see Viewing Path Interval Statistics, page 7-21.
Chapter 9 Command Reference lsspathists Command Description lsspathcst List current statistics for a SONET path lsspathcsts List current statistics for all SONET paths lsspathtst List total statistics for a SONET path lsspathtsts List total statistics for all SONET paths lsspathist List interval statistics for a SONET path lssonetstat List alarm statistics for an OC-3 line lssonetstats List alarm statistics for all OC-3 lines Cisco MGX 8260 Command Line Interface Guide 9-330 Release 1.
Chapter 9 Command Reference lsspathtst lsspathtst List total statistics for a SONET path. lsspathtst Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 Usage Guidelines Use this command to display total ES, SES, CV, and UAS statistics for a SONET path.
Chapter 9 Command Reference lsspathtst Command Description lsslinecsts List current statistics for all SONET lines lsslinetst List total statistics for a SONET line lsslinetsts List total statistics for all SONET lines lsslineist List interval statistics for a SONET line lsslineists List interval statistics for all SONET lines lsspathcst List current statistics for a SONET path lsspathcsts List current statistics for all SONET paths lsspathtsts List total statistics for all SONET paths
Chapter 9 Command Reference lsspathtsts lsspathtsts List total statistics for all SONET paths. lsspathtsts Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to display total ES, SES, CV, and UAS statistics for all SONET paths. For more information, see Viewing Path Total Statistics, page 7-21.
Chapter 9 Command Reference lsspathtsts Command Description lsspathcst List current statistics for a SONET path lsspathcsts List current statistics for all SONET paths lsspathtst List total statistics for a SONET path lsspathist List interval statistics for a SONET path lsspathists List interval statistics for all SONET paths lssonetstat List alarm statistics for an OC-3 line lssonetstats List alarm statistics for all OC-3 lines Cisco MGX 8260 Command Line Interface Guide 9-334 Release
Chapter 9 Command Reference lssrt lssrt List static route lssrt Address Location Syntax Description Address An address in dotted notation w.x.y.z that has the last byte set to 0. Location The slot and line number, delimited by a period, of the origin of the static route. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced.
Chapter 9 Command Reference lssrts lssrts List static routes. lssrts Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Displays information about all static routes. Examples The following example displays information about all static routes.
Chapter 9 Command Reference lsssectioncst lsssectioncst List current statistics for a SONET section. lsssectioncst Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9.
Chapter 9 Command Reference lsssectioncst Command Description lsslinetst List total statistics for a SONET line lsslinetsts List total statistics for all SONET lines lsslineist List interval statistics for a SONET line lsslineists List interval statistics for all SONET lines lsspathcst List current statistics for a SONET path lsspathcsts List current statistics for all SONET paths lsspathtst List total statistics for a SONET path lsspathtsts List total statistics for all SONET paths lss
Chapter 9 Command Reference lsssectioncsts lsssectioncsts List current statistics for all SONET sections. lsssectioncsts Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to display current ES, SES, SEFS, and CV statistics for all SONET sections.
Chapter 9 Command Reference lsssectioncsts Command Description lsspathcsts List current statistics for all SONET paths lsspathtst List total statistics for a SONET path lsspathtsts List total statistics for all SONET paths lsspathist List interval statistics for a SONET path lsspathists List interval statistics for all SONET paths lssonetstat List alarm statistics for an OC-3 line lssonetstats List alarm statistics for all OC-3 lines Cisco MGX 8260 Command Line Interface Guide 9-340 Rel
Chapter 9 Command Reference lsssectionist lsssectionist List interval statistics for a SONET section. lsssectionist Location Interval Syntax Description Location The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9. Valid lines: 1-4 Interval The measurement interval of interest. Values: 1-96, where 1 is the most recent interval Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.
Chapter 9 Command Reference lsssectionist Command Description lsslinecst List current statistics for a SONET line lsslinecsts List current statistics for all SONET lines lsslinetst List total statistics for a SONET line lsslinetsts List total statistics for all SONET lines lsslineist List interval statistics for a SONET line lsslineists List interval statistics for all SONET lines lsspathcst List current statistics for a SONET path lsspathcsts List current statistics for all SONET paths
Chapter 9 Command Reference lsssectionists lsssectionists List interval statistics for all SONET sections. lsssectionists Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to display interval ES, SES, SEFS, and CV statistics for all SONET sections.
Chapter 9 Command Reference lsssectionists Command Description lsspathcsts List current statistics for all SONET paths lsspathtst List total statistics for a SONET path lsspathtsts List total statistics for all SONET paths lsspathist List interval statistics for a SONET path lsspathists List interval statistics for all SONET paths lssonetstat List alarm statistics for an OC-3 line lssonetstats List alarm statistics for all OC-3 lines Cisco MGX 8260 Command Line Interface Guide 9-344 Rel
Chapter 9 Command Reference lsssectiontst lsssectiontst List total statistics for a SONET section. lsssectiontst Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. The slot and line number, delimited by a period, of the OC-3 line. Valid slot: 9.
Chapter 9 Command Reference lsssectiontst Command Description lsslinetst List total statistics for a SONET line lsslinetsts List total statistics for all SONET lines lsslineist List interval statistics for a SONET line lsslineists List interval statistics for all SONET lines lsspathcst List current statistics for a SONET path lsspathcsts List current statistics for all SONET paths lsspathtst List total statistics for a SONET path lsspathtsts List total statistics for all SONET paths lss
Chapter 9 Command Reference lsssectiontsts lsssectiontsts List total statistics for all SONET sections. lsssectiontsts Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.2 This command was first introduced. Usage Guidelines Use this command to display total ES, SES, SEFS, and CV statistics for all SONET sections.
Chapter 9 Command Reference lsssectiontsts Command Description lsspathcsts List current statistics for all SONET paths lsspathtst List total statistics for a SONET path lsspathtsts List total statistics for all SONET paths lsspathist List interval statistics for a SONET path lsspathists List interval statistics for all SONET paths lssonetstat List alarm statistics for an OC-3 line lssonetstats List alarm statistics for all OC-3 lines Cisco MGX 8260 Command Line Interface Guide 9-348 Rel
Chapter 9 Command Reference lstmgr lstmgr List trap manager. lstmgr Addr Syntax Description Addr Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. The IP address of the manager Usage Guidelines Displays information in the trap registration list about the manager at the specified address. For more information, see Viewing SNMP Trap Registrations, page 6-30.
Chapter 9 Command Reference lstmgrs lstmgrs List trap managers. lstmgrs Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to display information about all managers in the trap registration list. For more information, see Viewing SNMP Trap Registrations, page 6-30.
Chapter 9 Command Reference lstraps lstraps List the trap log. lstraps Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to display the date and time of each trap and alarms associated with them. Examples The following example displays information about all traps.
Chapter 9 Command Reference lsusp lsusp List a user profile. lsusp Index Syntax Description Index Defaults No default behavior or values. Command Modes Security level 1 Command History Release Modification 1.0 This command was first introduced. A userProfileTable index number. Values: 1 - 20. Usage Guidelines Use this command to list the specified user profile by index. To determine the index, use lsusps. For more information, see Viewing User Profiles, page 2-2.
Chapter 9 Command Reference lsusps lsusps List all user profiles. lsusps Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 1 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to list the user identifier and security level for all user profiles. For more information, see Viewing User Profiles, page 2-2.
Chapter 9 Command Reference lsvport lsvport List voice port lsusp Slot Port Syntax Description Slot The logical slot number of an NSC Port The logical port number Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Displays information about the specified voice port. Examples The following example displays information about the voice port at slot 1, port 3.
Chapter 9 Command Reference lsvports lsvports List voice ports lsvports Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 5 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to list information about all voice ports. Examples The following example lists information about all voice ports.
Chapter 9 Command Reference offbertds1 offbertds1 Stop BERT on DS1. offbertds1 Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced. The slot and line number, delimited by a period, of the DS1 line Usage Guidelines Use this command to stop the BERT on the specified DS1 line.
Chapter 9 Command Reference onbertds1 onbertds1 Start BERT on DS1. onbertds1 Location Pattern Rate DS0 StateCtrl Syntax Description Location The slot and line number, delimited by a period, of the DS1 line. Pattern One of the following patterns. Values: 1-13.
Chapter 9 Command Reference onbertds1 Command Modes Security level 3 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to start the BERT on the specified DS1 line. To specify which DS0s participate in a Bert test, use the Ds0 parameter. For example, 0000000000110101 specifies that the DS0 number 1, 3, 5 and 6 are participating. Convert this binary number to a decimal number and then enter that number on this option.
Chapter 9 Command Reference rmannfile rmannfile Remove an announcement file. rmannfile fid Syntax Description fid Defaults No default behavior or values Command Modes Security level Command History Release Modification 1.2 This command was first introduced. The announcement file ID. Values: 1-100 Usage Guidelines You use this command to remove an announcement file. Before attempting to remove an announcement file, first deactivate the file; otherwise, removal fails.
Chapter 9 Command Reference resetcd resetcd Reset card. resetcd Card Syntax Description Card Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.0 This command was first introduced. The number of the card to reset Usage Guidelines Use this command to specify a card to reset. Examples The following example resets card 1.
Chapter 9 Command Reference resetnd resetnd Reset node, including all processor and service modules. resetnd Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to reset the node. Examples The following example resets the node.
Chapter 9 Command Reference swcd swcd Switch to redundant NSC. swcd Card Syntax Description Card Defaults No default behavior or values. Command Modes Security level 4 Command History Release Modification 1.0 This command was first introduced. The slot number of active card to switch for the standby redundant card Usage Guidelines Use this command to switch between the active and standby cards of a redundant pair.
Chapter 9 Command Reference swclk swclk Switch clock. swclk Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 2 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to switch from the current clock source to the standby clock source. Examples The following example switches to the standby clock.
Chapter 9 Command Reference upethln upethln Activate Ethernet line. upethln Location Syntax Description Location Defaults No default behavior or values. Command Modes Security level 4 Command History Release Modification 1.0 This command was first introduced. The slot and line number, delimited by a period, of the Ethernet line Usage Guidelines Use this command to bring up an Ethernet interface. Examples The following example brings up the Ethernet interface at slot 9 line 1, address 10.
Chapter 9 Command Reference upgd upgd Upgrade the software image. upgd upgdLogicalCardIndex upgdFileName Syntax Description upgdLogicalCardIndex The logical number of the card to upgrade. Values: 1-16. upgdFileName The file name of the upgrade image. Values: SCC image: SCC_<9-character string>.fw NSC image: NSC_<9-character string>.fw BSC image: BSC_<9-character string>.fw Defaults No default behavior or values. Command Modes Security level 1 Command History Release Modification 1.1.
Chapter 9 Command Reference upgdcancel upgdcancel Cancel a software image upgrade. upgdcancel upgdLogicalCardIndex Syntax Description upgdLogicalCardIndex Defaults No default behavior or values. Command Modes Security level 1 Command History Release Modification 1.1.3 This command was first introduced. The logical number of the card to upgrade. Values: 1-16. Usage Guidelines Use this command to gracefully cancel a software image upgrade in a redundant system.
Chapter 9 Command Reference upgdcmit upgdcmit Commit the new software image. upgdcmit upgdLogicalCardIndex Syntax Description upgdLogicalCardIndex Defaults No default behavior or values. Command Modes Security level 1 Command History Release Modification 1.1.3 This command was first introduced. The logical number of the card to upgrade. Values: 1-16. Usage Guidelines Use this command to commit the new software image. The system sends a confirmation message on successful completion.
Chapter 9 Command Reference version version Show the software version. version Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to display the version information about the MGX 8260 Media Gateway. Examples The following example displays the software version.
Chapter 9 Command Reference whoami whoami List the name of the user who is currently logged in. whoami Syntax Description The command has no arguments or keywords. Defaults No default behavior or values. Command Modes Security level 6 Command History Release Modification 1.0 This command was first introduced. Usage Guidelines Use this command to determine who is logged in. Examples The following example displays the name of the user who is logged in.
Chapter 9 Command Reference whoami Cisco MGX 8260 Command Line Interface Guide 9-370 Release 1.2, Part Number 78-10987-01 Rev.
I N D E X upgrading A 3-23, 3-24 cards alarms configuration tasks card 6-4 configuring configuration tasks 6-24 resetting DS1/E1 Alarms Viewing DS3 E1 clearing alarms 6-8 card environmental shelf 3-11 viewing summary information 6-12, 6-15 OC-3c 3-1, 3-2 viewing configuration and status 6-5 6-19 Fast Ethernet 6-15 8-6 environmental Fast Ethernet surveillance tasks 6-1 SONET CLI reference setting DS1 6-7 configurations setting DS3 6-19 backing up 6-19 restoring viewi
Index adding deleting 5-22 E 5-22 DLSAP statistics viewing E1 performance Alarms 5-24 clearing real-time 5-23 viewing current dmc lines, mapping 4-11 4-3 bert test Viewing Total deleting changing 4-7 configuring deleting listing listing summary information 4-3, 4-6 8-2 6-25 6-26 6-26 registering 6-25 email server viewing configuration and status 4-2, 4-3 DS1 statistics registering 6-25 e-rdi and trace parameters clearing real-Time clearing real-time 7-5 7-1 viewing inter
Index system deleting entries 1-5 IPDC viewing activating the Link Health Check core settings 5-33 core parameters timers and counters ip addresses 5-33 5-5 status information, viewing IPDC to MGCP, switching from voice parameters, viewing 5-3 5-4 5-4 settings, viewing 5-36 5-33 ip routes, configuring 5-4 default call setup parameters 5-32 viewing cot information viewing settings 4-13 MGCP 5-32 soft switch ip addresses 4-13 5-8 5-6 MGCP to IPDC, switching from 2-10 5-31 m
Index configuring R deleting redundancy 6-29 registering adding bsc 3-17 adding nsc 3-16 configuring deleting 6-28 viewing 6-28 6-30 software 3-15 upgrading 3-17 3-21 SONET invoking a switchback 3-18 alarm statistics physical and logical slot numbers understanding 3-11 line statistics 3-11 loopback 7-23 7-17 8-4 using 1 to 1 3-13 path statistics using 1 to n 3-12 performance alarm statistics, clearing viewing 3-15 7-20 section statistics rudp 7-25 7-14 static rout
Index V voice port viewing configuration and status 4-27 voice ports adding changing deleting 4-26 4-27 4-27 Cisco MGX 8260 Command Line Interface Guide Release 1.2, Part Number 78-10987-01 Rev.
Index Cisco MGX 8260 Command Line Interface Guide 6 Release 1.2, Part Number 78-10987-01 Rev.
