Cisco MDS 9000 Fabric Manager Quick Configuration Guide May 2006 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m CONTENTS Preface vii Audience vii Organization vii Document Conventions viii Related Documentation ix Release Notes ix Compatibility Information ix Regulatory Compliance and Safety Information Hardware Installation ix Cisco Fabric Manager x Command-Line Interface x Troubleshooting and Reference x Installation and Configuration Note x Obtaining Documentation x Cisco.
Contents Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Contents Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Contents Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Preface This preface describes the audience, organization, and conventions of the Cisco MDS 9000 Family Fabric Manager Quick Configuration Guide. It also provides information on how to obtain related documentation. Audience This guide is for experienced network administrators who are responsible for configuring and maintaining the Cisco MDS 9000 Family of multilayer directors and fabric switches.
Preface Document Conventions Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Chapter Title Description Appendix B Configuring Static Domain IDs and Persistent FC IDs Provides the procedure for configuring static domain IDs and persistent FC IDs. Appendix C Configuration Files Describes how to save and copy configuration files that contain the parameters required to configure a switch.
Preface Related Documentation Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Related Documentation The documentation set for the Cisco MDS 9000 Family includes the following documents. To find a document online, use the Cisco MDS SAN-OS Documentation Locator at: http://www.cisco.com/en/US/products/ps5989/products_documentation_roadmap09186a00804500c1.html.
Preface Related Documentation Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Preface Documentation Feedback Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Cisco.com You can access the most current Cisco documentation at this URL: http://www.cisco.com/techsupport You can access the Cisco website at this URL: http://www.cisco.com You can access international Cisco websites at this URL: http://www.cisco.com/public/countries_languages.
Preface Cisco Product Security Overview Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m You can submit comments about Cisco documentation by using the response card (if present) behind the front cover of your document or by writing to the following address: Cisco Systems Attn: Customer Document Ordering 170 West Tasman Drive San Jose, CA 95134-9883 We appreciate your comments.
Preface Obtaining Technical Assistance Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m at this URL: http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html The link on this page has the current PGP key ID in use. Obtaining Technical Assistance Cisco Technical Support provides 24-hour-a-day award-winning technical assistance. The Cisco Technical Support & Documentation website on Cisco.
Preface Obtaining Additional Publications and Information Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.
Preface Obtaining Additional Publications and Information Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m • iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies learn how they can use technology to increase revenue, streamline their business, and expand services.
Preface Obtaining Additional Publications and Information Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m C H A P T E R 1 Overview The primary objective of the Cisco MDS 9000 Family Fabric Manager Quick Configuration Guide is to get you started with configuring your Cisco MDS 9000 Family switch using the Cisco Fabric Manager graphical user interface (GUI).
Chapter 1 Overview Overview of Fabric Manager Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Start the process by setting up the hardware and performing the initial switch setup using the CLI. Then install Cisco Fabric Manager, and use it to configure VSANs, interfaces, zones, and zone sets, which are the minimum requirements for creating a fabric.
Chapter 1 Overview Overview of VSANs, Interfaces, Zones, and Zone Sets Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m VSANs and zoning within the MDS 9000 Family of products aid the SAN designer in building secure and manageable networking environments while optimizing the use and cost of switching hardware.
Chapter 1 Overview Overview of VSANs, Interfaces, Zones, and Zone Sets Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m C H A P T E R 2 Initial Switch Configuration This chapter provides instructions for setting up the hardware, connecting to the console port, and initially configuring the switch from the CLI.
Chapter 2 Initial Switch Configuration Connecting the Console Port Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Connecting the Console Port This section describes how to connect the RS-232 console port to a PC. The console port allows you to perform the following functions: • Configure the switch from the CLI. • Monitor network statistics and errors. • Configure SNMP agent parameters.
Chapter 2 Initial Switch Configuration Connecting the Console Port Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Chapter 2 Initial Switch Configuration Connecting the 10/100 Ethernet Management Port Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Connecting the Console Port to a PC You can connect the console port to a PC serial port for local administrative access to the Cisco MDS 9000 Family switch. Note The PC must support VT100 terminal emulation.
Chapter 2 Initial Switch Configuration Connecting to the MGMT 10/100/1000 Ethernet Port Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m If only the active supervisor module is connected to the LAN and an event occurs that causes a system switchover (such as a software upgrade), the switch becomes unmanageable through the Ethernet port after the active supervisor module reboots and the standby supervisor module becomes the active supervisor module.
Chapter 2 Initial Switch Configuration Using the Switch Setup Utility Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m General Software Pentium III Embedded BIOS 2000 (tm) Revision 1.1.(0) (C) 2002 General Software, Inc.ware, Inc. Pentium III-1.1-6E69-AA6E +------------------------------------------------------------------------------+ | System BIOS Configuration, (C) 2002 General Software, Inc.
Chapter 2 Initial Switch Configuration Using the Switch Setup Utility Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Would you like to enter the basic configuration dialog (yes/no): yes The switch setup utility guides you through the basic configuration process. Press Ctrl-C at any prompt to end the configuration process. Step 6 Enter no (no is the default) to not create any additional accounts.
Chapter 2 Initial Switch Configuration Using the Switch Setup Utility Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Step 18 Enter on (on is the default) to configure the switch port trunk mode. Configure default switchport trunk mode (on/off/auto) [on]: on Step 19 Enter deny (deny is the default) to configure a default zone policy configuration.
Chapter 2 Initial Switch Configuration Using the Switch Setup Utility Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Step 21 Enter no (no is the default) if you are satisfied with the configuration.
Chapter 2 Initial Switch Configuration Verifying the Module Status Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Verifying the Module Status Before you proceed with further configuration of the switch, ensure that the modules in the chassis are functioning as designed. To verify the status of a module at any time, issue the show module command. All the hardware that was physically installed should be displayed.
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m C H A P T E R 3 Installing and Launching Fabric Manager Before installing Fabric Manager, make sure that the hardware setup and initial configuration using the CLI is completed. See Chapter 2, “Initial Switch Configuration,” for details. The Cisco Fabric Manager software executable files reside on every supervisor module of each Cisco MDS 9000 Family switch in your network.
Chapter 3 Installing and Launching Fabric Manager Installing Cisco Fabric Manager Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m To install Fabric Manager for the first time, or to update or reinstall the software, follow these steps: Step 1 Enter the mgmt0 IP address or host name of the supervisor module in the Address or Location field of your browser. Click the Cisco Fabric Manager link on the Cisco Fabric Manager home page shown in Figure 3-1.
Chapter 3 Installing and Launching Fabric Manager Launching Cisco Fabric Manager Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Note The Fabric Manager Server and the Fabric Manager Client must be able to communicate with each other at all times. They can be installed on different workstations or the same workstation.
Chapter 3 Installing and Launching Fabric Manager Launching Cisco Fabric Manager Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Figure 3-2 Fabric Manager Login Screen Step 3 Enter the IP address or host name in the Fabric Seed Switch field, or select an IP address from the list of previously accessed devices in the drop-down menu. Step 4 Enter a user name and password in the appropriate fields.
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m C H A P T E R 4 Configuring VSANs and Interfaces Before configuring VSANs and interfaces, make sure that you have launched and logged into Fabric Manager from your workstation. See Chapter 3, “Installing and Launching Fabric Manager,” for details. You can achieve higher security and greater stability in Fibre Channel fabrics by using virtual storage area networks (VSANs).
Chapter 4 Configuring VSANs and Interfaces Creating VSANs Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Creating VSANs VSANs help you create multiple logical SANs over a common physical infrastructure. Each VSAN can contain up to 239 switches and has an independent address space that allows identical Fibre Channel IDs (FC IDs) to be used simultaneously in different VSANs.
Chapter 4 Configuring VSANs and Interfaces Creating VSANs Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m You see the Create VSAN dialog box. (See Figure 4-3.) Figure 4-3 Step 2 Create VSAN Complete the fields in the Create VSAN dialog box. • Select the switches that you wish to assign to the VSAN. For example, in Figure 4-3, switch_name is the switch selected to be assigned to a VSAN. • Select a VSAN ID for the VSAN.
Chapter 4 Configuring VSANs and Interfaces Configuring Interfaces Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Note • Step 3 HP-UX and AIX are two operating systems that utilize the FC ID in the device path to the storage. For the switch to always assign the same FC ID to a device, persistent FC IDs and static Domain ID must be configured for the VSAN. Check the FICON check box if the VSAN is FICON-enabled. Click Create to add the VSAN.
Chapter 4 Configuring VSANs and Interfaces Configuring Interfaces Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Enabling or Disabling Interfaces Note You are not required to enable interfaces if the default state of the ports in the setup script is set to noshut. See the “Using the Switch Setup Utility” section on page 2-5.
Chapter 4 Configuring VSANs and Interfaces Configuring Interfaces Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m C H A P T E R 5 Configuring Zones and Zone Sets Before setting up zones and zone sets make sure you have configured VSANs and interfaces. See Chapter 4, “Configuring VSANs and Interfaces.” Zoning enables you to set up access control between storage devices or user groups.
Chapter 5 Configuring Zones and Zone Sets Configuring Zones Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m This chapter includes the following sections: • Configuring Zones, page 5-2 • Creating Zone Sets, page 5-4 • What’s Next?, page 5-6 Configuring Zones Zones are configured within VSANs. The Logical tab displays the VSANs configured in the currently discovered fabric.
Chapter 5 Configuring Zones and Zone Sets Configuring Zones Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Step 3 Click Zones then click Insert icon to make a new zone. We recommend that you use meaningful names for a zone. For example, you could use email05_HBA2_EMC_FA11a. (See Figure 5-4.) Figure 5-4 Tip Edit Local Full Zone Database Instead of configuring zones using pWWNs, you can use device aliases as zone members.
Chapter 5 Configuring Zones and Zone Sets Creating Zone Sets Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Step 4 Drag and drop devices into the zone. Once the zone is populated with the devices, the name of the zone is displayed in italics. Click Add to zone or alias to move devices up or down by alias or by zone. (See Figure 5-5.) Figure 5-5 Adding Devices to a Zone Set Creating Zone Sets A zone set consists of one or more zones.
Chapter 5 Configuring Zones and Zone Sets Creating Zone Sets Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m To create zone sets, follow these steps: Step 1 Click Zone > Edit Local Full Zone Database from the Zone menu or right-click a VSAN folder in the Logical tab and choose Edit Local Full Zone Database from the pop-up menu. Step 2 Select a VSAN and click OK. You see the VSAN you selected in the Edit Local Full Zone Database window.
Chapter 5 Configuring Zones and Zone Sets What’s Next? Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m What’s Next? After completing the procedures in this book, your Cisco MDS 9000 Family switch can provide the basic, minimal Fibre Channel services necessary to enable hosts to access their storage. Beyond this, you will want to set up security, management, and monitoring for your network. These tasks are beyond the scope of this document.
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m A P P E N D I X A Fabric Manager Client The Cisco Fabric Manager Client is a Java-based GUI application that provides easy access to Fabric Manager applications from a remote workstation.
Appendix A Fabric Manager Client Fabric Manager Client Quick Tour Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Fabric Manager Client Quick Tour This section helps you get familiar with the various icons and sections that enable navigation in the Fabric Manager Client interface, as shown in Figure A-1. Figure A-1 Fabric Manager Main Window 1 Menu bar—Provides access to options that are organized by menus.
Appendix A Fabric Manager Client Fabric Manager Client Quick Tour Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Note As of Cisco MDS SAN-OS Release 2.1(1a), advanced mode is enabled by default and provides the full suite of Fabric Manager features, including security, IVR, iSCSI, and FICON. Uncheck the Advanced check box in the upper right corner of Fabric Manager Client to simplify the user interface.
Appendix A Fabric Manager Client Fabric Manager Client Quick Tour Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m The information for both fabrics is displayed, with no need to select a seed switch. To see details of a fabric, select the tab for that fabric at the bottom of the Fabric pane, or double-click the cloud icon for the fabric in the All Fabrics tab. Contents Panes The following sections describe the panes in the Fabric Manager view.
Appendix A Fabric Manager Client Fabric Manager Client Quick Tour Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Table A-1 Fabric Manager Graphics (continued) Icon or Graphic Description Fibre Channel target (or enclosure). iSCSI host. Fibre Channel ISL and edge connection. Fibre Channel PortChannel. IP ISL and edge connection. IP PortChannel. Fibre Channel loop (storage). IP cloud (iSCSI hosts).
Appendix A Fabric Manager Client Fabric Manager Client Quick Tour Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Note When a VSAN, zone, or zone member is selected in the VSAN tree, the map highlighting changes to identify the selected objects. To remove this highlighting, click Clear Highlight on the Fabric pane toolbar or choose Clear Highlight from the pop-up menu.
Appendix A Fabric Manager Client Fabric Manager Client Quick Tour Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Table A-2 Icon Fabric Manager Client Main Toolbar (continued) Description Edits full zone database. Launches IVR zone wizard. Launches PortChannel wizard. Launches FCIP wizard. Launches iSCSI wizard. Launches QoS wizard. Configures users and roles. Launches IP-ACL wizard. Launches License Install wizard.
Appendix A Fabric Manager Client Fabric Manager Client Quick Tour Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Table A-2 Fabric Manager Client Main Toolbar (continued) Icon Description Monitor ISL performance. Show online help. Information Pane The Information pane displays tables of information associated with the option selected from the menu tree in the Logical Domains or Physical Attributes panes.
Appendix A Fabric Manager Client Fabric Manager Client Quick Tour Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Table A-3 Information Pane Toolbar (continued) Icon Description Print Table Prints the contents of the Information pane. Detach Table Displays a non-editable copy of the table in the Information pane in its own window, which you can move around the screen.
Appendix A Fabric Manager Client Fabric Manager Client Quick Tour Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m • Security—View and configure MDS management and FC-SP security. • ISLs—View and configure Inter-Switch Links. • End Devices—View and configure end devices. Status Bar The status bar at the bottom of the Fabric Manager window shows the last entry displayed by the discovery process, and the possible error message on the right side.
Appendix A Fabric Manager Client Fabric Manager Wizards Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Detachable Tables As of Cisco MDS SAN-OS Release 2.0(2b), Fabric Manager Client has detachable tables. You can detach tables and move them to different areas on your desktop so that you can compare similar tables from different VSANs, or you can keep informational tables open from one view while you examine a different area in Fabric Manager.
Appendix A Fabric Manager Client Fabric Manager Wizards Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m . A P P E N D I X B Configuring Static Domain IDs and Persistent FC IDs The domain manager on the principal switch in a VSAN assigns a domain ID to a switch that is joining the fabric. When a switch boots up or joins a new fabric, it can request a specific domain ID or take any available domain ID.
Appendix B Configuring Static Domain IDs and Persistent FC IDs S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m . In the following procedure, the existing VSAN has a switch C-186 with a domain ID of 209. In Fabric Manager, the VSAN is statically configured and a persistent FC ID is enabled. This procedure does not alter the running domain ID.
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m . A P P E N D I X C Configuration Files Configuration files can contain some or all of the commands needed to configure one or more switches. For example, you might want to download the same configuration file to several switches that have the same hardware configuration so that they have identical module and port configurations.
Appendix C Configuration Files Saving the Configuration File S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m . To copy the configuration file, follow these steps: Step 1 In the Physical Attributes pane, expand Switches > Copy Configuration. Step 2 Check the check box for each switch configuration that you want to save. Set the From and To fields for each switch. Step 3 Click Apply.
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Index REVIEW DRAFT—CISCO CONFIDENTIAL Cisco MDS 9100 Series switch (figure 2-3) 2-3 End Devices folder Cisco MDS 9200 Series switch (figure 2-2) 2-3 Events folder Cisco MDS 9500 Series Supervisor-2 Module (figure 2-1) 2-2 Cisco MDS 9500 Series switch (figure 2-1) connecting the RS-232 cable connecting to a PC Copy/Ctrl+C icon 5 Export icon 8 2-2 F 2-4 Fabric Manager 8 Create VSAN icon 9 2-2 8 Create Row icon Events tab advanced mode 6 browsers creating unique user names for each user
Index REVIEW DRAFT—CISCO CONFIDENTIAL Fabric pane Fabric tab 3 I B-1 configuring FC IDs and domain IDs (tip) Fibre Channel IDs. overview B-1 Fabric pane 11 toolbar 9 4 4 6 Information pane Fibre Channel ISL and Edge Connection icon Fibre Channel Loop icon 5 Fibre Channel Target icon 5 5 installation and configuration flowchart (figure) interfaces 5 2-7 2 installation folder Fibre Channel PortChannel icon 4-5 adding 4-4 configuring 5 enabling or disabling 6 mgmt 0 FMPersist.
Index REVIEW DRAFT—CISCO CONFIDENTIAL modules J verifying status J 2-4 Java 2-10 monitored fabrics 1 Monitor ISL Performance icon Mozilla LAN switch 2-4 large fabrics, viewing 3 N 5 Launch DPVM Wizard icon Launch FCIP Wizard icon 6 Netscape 7 Launch IP-ACL Wizard icon Launch iSCSI Wizard icon 7 preparing 7 Launch PortChannel Wizard icon 2-1 Non-director Class MDS 9000 Switch icon 7 noshut state Launch License Install Wizard icon Launch QoS Wizard icon 3-1 network connections La
Index REVIEW DRAFT—CISCO CONFIDENTIAL enabling B-2 S Physical Attributes pane overview 2, 10 scripts 9 physical connections ping command PortChannels security 2-5 serial port 3-3 service 10 PortChannel wizard 2-4 3-3 shell scripts 4-4 prerequisites for initial configuration 2-1 B-1 pWWN mappings show module command 2-10 Show Online Help icon 8 SNMP 5-3 2-7 community strings Q 2-7 connecting the console port QoS wizard traps 10 3-4 Software Install wizard R Solaris R
Index REVIEW DRAFT—CISCO CONFIDENTIAL configure the interfaces 4-4 minimum configuration 1-2 move ports U uninstalling Fabric Manager 4-4 switch(boot) prompt upgrading 2-5 3-2 3-2 switch configuration commands CLI and Fabric Manager Switches folder 1-2 Switch Setup Utility default gateway VSANs 2-5 advanced IP options adding 2-7 default zone policy 4-2 configuring 2-7 default switch port interface overview 2-6 first-time configuration 2-6 full zone set distribution 2-8 4-3 VS
Index REVIEW DRAFT—CISCO CONFIDENTIAL rules 5-4 Cisco MDS 9000 Family Fabric Manager Quick Configuration Guide OL-7765-02 IN-9
Index REVIEW DRAFT—CISCO CONFIDENTIAL Cisco MDS 9000 Family Fabric Manager Quick Configuration Guide IN-10 OL-7765-02
