User guide

ManualsBrandsCisco ManualsComputer equipmentIAD2431-16FXS

Release Notes for Cisco IOS Release 12.4T

OL-8012-09 Rev. B0

Feature Support

Cisco IOS software is packaged in feature sets that consist of software images that support specific

platforms. The feature sets available for a specific platform depend on which Cisco IOS software images

are included in a release. Each feature set contains a specific set of Cisco IOS features.

Caution Cisco IOS images with strong encryption (including, but not limited to 168-bit (3DES) data encryption

feature sets) are subject to U.S. government export controls and have limited distribution. Strong

encryption images to be installed outside the United States are likely to require an export license.

Customer orders may be denied or subject to delay because of U.S. government regulations. When

applicable, the purchaser/user must obtain local import and use authorizations for all encryption

strengths. Please contact your sales representative or distributor for more information, or send an e-mail

to export@cisco.com.

The feature set tables have been removed from the Cisco IOS Release 12.4T release notes to improve the

usability of the release notes documentation. The feature-to-image mapping that was provided by the

feature set tables is available through Cisco Feature Navigator.

Cisco Feature Navigator is a web-based tool that enables you to determine which Cisco IOS software

images support a specific set of features and which features are supported in a specific Cisco IOS image.

You can search by feature or by feature set (software image). Under the release section, you can compare

Cisco IOS software releases side by side to display both the features unique to each software release and

the features that the releases have in common.

Cisco Feature Navigator is updated regularly when major Cisco IOS software releases and technology

releases occur. For the most current information, go to the Cisco Feature Navigator home page at the

following URL:

http://www.cisco.com/go/cfn

For frequently asked questions about Cisco Feature Navigator, see the FAQs at the following URL:

http://www.cisco.com/support/FeatureNav/FNFAQ.html

Determining Which Software Images (Feature Sets) Support a Specific Feature

To determine which software images (feature sets) in Cisco IOS Release 12.4T support a specific

feature, go to the Cisco Feature Navigator home page and perform the following steps.

Step 1 From the Cisco Feature Navigator home page, click Search by feature.

Step 2 To find a feature, use either “Search by full or partial feature name” or “Browse features in alphabetical

order.” Either a list of features that match the search criteria or a list of features that begin with the

number or letter chosen from the ordered list will be displayed in the Features available text box on the

left side of the web page.

Step 3 Choose a feature from the Features available text box, and click the Add button to add a feature to the

Features selected text box on the right side of the web page.

Note To learn more about a feature in the list, click the Show Description(s) button below the Features

available text box.

Repeat this step to add features. A maximum of 20 features can be chosen for a single search.

Step 4 Click Continue when you are finished choosing features.

Summary of content (94 pages)

PAGE 1
Feature Support Feature Support Cisco IOS software is packaged in feature sets that consist of software images that support specific platforms. The feature sets available for a specific platform depend on which Cisco IOS software images are included in a release. Each feature set contains a specific set of Cisco IOS features. Caution Cisco IOS images with strong encryption (including, but not limited to 168-bit (3DES) data encryption feature sets) are subject to U.S.
PAGE 2
Memory Recommendations Step 5 From the Major Release drop-down list, choose 12.4T. Step 6 From the Release drop-down list, choose the appropriate maintenance release. Step 7 From the Platform drop-down list, choose the appropriate hardware platform. The “Search Results” table will list all the software images (feature sets) that support the features that you chose.
PAGE 3
Memory Recommendations Determining Memory Recommendations for Software Images (Feature Sets) To determine memory recommendations for software images (feature sets) in Cisco IOS Release 12.4T, go to the Cisco Feature Navigator home page and perform the following steps. Step 1 From the Cisco Feature Navigator home page, click Search by Software/Image Name/Product Code/Platform.
PAGE 4
Platform-Specific Information Platform-Specific Information This section describes the platform-specific information for the Cisco platforms supported by Cisco IOS Release 12.4T. Each section includes memory requirements and supported features. Additional information is provided when applicable.
PAGE 5
Platform-Specific Information Cisco SOHO 90 Series Routers This section contains the following sections with information that is specific to the Cisco SOHO 90 series routers: • Memory Recommendations, page 11 • Supported Hardware, page 11 • Feature Support, page 11 Memory Recommendations For memory recommendations for the Cisco SOHO 90 series routers in Cisco IOS Release 12.4T, see the “Memory Recommendations” section on page 8. Supported Hardware Cisco IOS Release 12.
PAGE 6
Platform-Specific Information Cisco VG202 and Cisco VG204 Voice Gateways This section contains the following sections with information that is specific to the Cisco VG202 and Cisco VG204 analog voice gateways: • Introduction, page 12 • Memory Recommendations, page 12 • Supported Hardware, page 12 • Feature Support, page 12 Introduction The Cisco VG202 and Cisco VG204 voice gateways are analog voice gateways for use in the service provider, commercial and Enterprise markets.
PAGE 7
Platform-Specific Information Cisco VG224 Analog Gateways This section contains the following sections with information that is specific to the Cisco VG224 analog gateways: • Introduction, page 13 • Memory Recommendations, page 13 • Supported Hardware, page 13 • Feature Support, page 13 Introduction The Cisco VG224 series is a family of analog gateways. The Cisco VG224 has a 24-port Foreign Exchange Station (FXS) through an RJ-21 connector and two 10/100BASE-T interfaces.
PAGE 8
Platform-Specific Information Cisco VGD 1T3 Voice Gateways This section contains the following sections with information that is specific to the Cisco VG224 analog gateways: • Introduction, page 14 • Memory Recommendations, page 14 • Supported Hardware, page 14 • Feature Support, page 14 Introduction The Cisco VGD 1T3 is a high density voice gateway with up to one Channelized T3 (CT3) of voice over IP (VoIP) capacity with support for Cisco Unified Communications Manager and Cisco Voice Portal appli
PAGE 9
Platform-Specific Information Cisco Secure Router 500 Series This section contains the following sections with information that is specific to the Cisco secure router 500series: • Introduction, page 15 • Memory Recommendations, page 15 • Supported Hardware, page 15 • Feature Support, page 16 Introduction The Cisco Secure Router 520 Series routers are designed for small businesses with up to 50 users and teleworkers who want secure connectivity to corporate LANs and to the Internet.
PAGE 10
Platform-Specific Information For additional information about supported hardware for this platform and release, see the Cisco Software Advisor at the following location: http://tools.cisco.com/Support/Fusion/FusionHome.do Feature Support For feature support in Cisco IOS Release 12.4, see the “Feature Support” section on page 7. Release Notes for Cisco IOS Release 12.4T 16 OL-8012-09 Rev.
PAGE 11
Platform-Specific Information Cisco Unified Communications 500 Series This section contains the following sections with information that is specific to the Cisco unified communications 500 series: • Introduction, page 17 • Memory Recommendations, page 17 • Supported Hardware, page 17 • Feature Support, page 17 Introduction The Cisco Unified Communications 500 platform provides voice, data, voicemail, Automated Attendant, video, security, and wireless capabilities while integrating with existing des
PAGE 12
Platform-Specific Information Cisco 800 Series Routers This section contains the following sections with information that is specific to the Cisco 800 series routers: • Memory Recommendations, page 18 • Supported Hardware, page 18 • Feature Support, page 19 • Additional Notes for the Cisco 800 Series, page 19 Memory Recommendations For memory recommendations for the Cisco 800 series routers in Cisco IOS Release 12.4T, see the “Memory Recommendations” section on page 8.
PAGE 13
Platform-Specific Information Feature Support For feature support in Cisco IOS Release 12.4, see the “Feature Support” section on page 7. Additional Notes for the Cisco 800 Series This section contains important information about using the Cisco 800 series routers with Cisco IOS Release 12.4T software. ADSL2 and ADSL2+ Support Cisco IOS Release 12.4(4)T introduces ADSL2 and ADSL2+ features for the Cisco 857, Cisco 876 and Cisco 877 routers.
PAGE 14
Platform-Specific Information ! ! ip subnet-zero ip dhcp excluded-address 10.10.10.1 ! ip dhcp pool SERVER network 10.10.10.0 255.255.255.0 default-router 10.10.10.1 import all ! ! ! bridge irb ! ! ! ! interface Ethernet0 ip address 10.10.10.1 255.255.255.0 no ip directed-broadcast ip nat inside ! interface ATM0 no ip address no ip directed-broadcast no atm ilmi-keepalive bundle-enable hold-queue 208 in ! interface ATM0.
PAGE 15
Platform-Specific Information ! voice-port 3 timing hookflash-in 0 ! voice-port 4 timing hookflash-in 0 ! ! line con 0 exec-timeout 0 0 transport input none stopbits 1 line vty 0 4 password lab login ! scheduler max-task-time 5000 end Downloading Images Delete files in the router flash memory before attempting to download new images. Caution Use the delete command, not the erase command, to free up space. Entering the erase command removes all files, including the configuration.
PAGE 16
Platform-Specific Information PPP over AAL5SNAP Encapsulation Support PPP over AAL5SNAP encapsulation is not supported, although the context-sensitive help mentions that it can be configured. Cisco 800 Series Router Clock—CSCdp09409 To run IP Security (IPSec) successfully, the Cisco 800 series router clock needs to be set accurately. Cisco 800 series router clocks are set and maintained using Simple Network Time Protocol (SNTP).
PAGE 17
Platform-Specific Information B-Channel Activation When a call comes in, a B channel is activated. If the amount of traffic on the B channel exceeds a threshold, the other B channel is activated. If the amount of traffic falls below the threshold, one of the B channels is deactivated. The B channel that is initially activated when the call comes in is not necessarily B1, nor is the B channel that is deactivated when the traffic level lessens necessarily B2. Release Notes for Cisco IOS Release 12.
PAGE 18
Platform-Specific Information Cisco 1700 Series Routers This section contains the following sections with information that is specific to the Cisco 1700 series routers: • Memory Recommendations, page 24 • Hardware Supported, page 24 • Feature Support, page 32 • Additional Notes for the Cisco 1700 Series Routers, page 32 Memory Recommendations For memory recommendations for the Cisco 1700 series routers in Cisco IOS Release 12.4, see the “Memory Recommendations” section on page 8.
PAGE 19
Platform-Specific Information • One 10/100BASE-TX Fast Ethernet port (RJ-45) • One auxiliary (AUX) port • One console port • DRAM memory: 96 MB default, 128 MB maximum • Flash memory: 32 MB default, 32 MB maximum Cisco 1711 The Cisco 1711 router provides Internet and intranet access and includes the following features: • Support for virtual private networking • Fixed architecture • Network device integration The Cisco 1711 router has the following hardware components: • One autosensing 10/
PAGE 20
Platform-Specific Information • One auxiliary (AUX) port (up to 115.2 kbps asynchronous serial) • One console port • VPN Hardware Encryption Module • Motorola MPC862P PowerQUICC at 100 MHz.
PAGE 21
Platform-Specific Information • WIC-1B-S/T-V3: one-port ISDN WIC (dial and leased line) • WIC-1B-U-V2: one-port ISDN BRI NT-1 WIC for the Cisco 1700, 2600, 3600, and 3700 series • WIC-1DSU-56K4: one-port integrated 56/64-kbps 4-wire DSU/CSU • WIC-1DSU-T1: one-port integrated T1/fractional T1 DSU/CSU • WIC-1DSU-T1-V2: updated one-port T1/fractional T1 DSU/CSU WIC • WIC-1ENET: one-port 10BASE-T Ethernet • WIC-1SHDSL: one-port G.
PAGE 22
Platform-Specific Information • Synchronous serial interfaces on serial WICs • Asynchronous serial interfaces on serial WICs • ISDN WICs-ISDN dialup and ISDN leased line (IDSL) at 144 kbps. Encapsulation over ISDN leased line: Frame Relay and PPP • One auxiliary (AUX) port (up to 115.
PAGE 23
Platform-Specific Information The following T1/E1 multiflex VWICs are also supported on the Cisco 1751 (and shared with the Cisco 2600 and Cisco 3600 series routers) and can be used for both channelized data and voice applications: • VWIC-1MFT-E1: one-port RJ-48 multiflex trunk (E1) • VWIC-2MFT-E1: two-port RJ-48 multiflex trunk (E1) • VWIC-1MFT-G703: one-port RJ-48 multiflex trunk (G.703) • VWIC-2MFT-G703: two-port RJ-48 multiflex trunk (G.
PAGE 24
Platform-Specific Information Cisco 1760 The voice- and data-capable Cisco 1760 router provides global Internet and company intranet access, and includes the following features: • VoIP voice and data functionality; the router can carry voice traffic (for example, telephone calls and faxes) over an IP network • Support for Cisco IOS Firewall, Intrusion Detection Systems, and IPSec Virtual Private Networks • Modular architecture • Network device integration The Cisco 1760 router has the following har
PAGE 25
Platform-Specific Information • WIC-1DSU-56K4: one-port integrated 56/64-kbps 4-wire DSU/CSU • WIC-1DSU-T1: one-port integrated T1/fractional T1 DSU/CSU • WIC-1DSU-T1-V2: updated one-port T1/fractional T1 DSU/CSU WIC • WIC-1ENET: one-port 10BASE-T Ethernet • WIC-1SHDSL: one-port G.
PAGE 26
Platform-Specific Information • VIC2-2E/M • VIC2-4FXO: four-port voice interface card—FXO (universal) • VIC-2BRI-NT/TE: two-port voice/fax interface card (BRI [NT and TE]) • VPN Module: MOD1700-VPN Feature Support For feature support in Cisco IOS Release 12.4, see the “Feature Support” section on page 7. Additional Notes for the Cisco 1700 Series Routers This section contains important information about using the Cisco 1700 series routers with Cisco IOS Release 12.4T software.
PAGE 27
Platform-Specific Information Multipartition Flash Defaults When you use a multipartition Flash card, the various flash partitions are referred to as “flash:1:”, “flash:2:”, and so on. If you specify only “flash” in a multipartition flash, the parser assumes “flash:1:”. For example, if you enter the show flash all command, the parser defaults to “show flash:1: all” and only the flash information for the first partition displays.
PAGE 28
Platform-Specific Information Cisco 1800 Series Routers (Fixed Configuration and Modular) This section contains the following sections with information that is specific to the Cisco 1800 series routers: • Memory Recommendations, page 34 • Supported Hardware, page 34 • Feature Support, page 37 • Additional Notes for the Cisco 1800 Series, page 37 Memory Recommendations For memory recommendations for the Cisco 1800 series routers in Cisco IOS Release 12.
PAGE 29
Platform-Specific Information • IEEE 802.11a and 802.11b/g wireless Cisco 1802 Routers The Cisco 1802 router has the following hardware components: • One Fast Ethernet port • One ADSL over ISDN port • One ISDN-BRI S/T port • Eight Fast Ethernet Switch ports Cisco 1802W Routers The Cisco 1802W router has the following hardware components: • One Fast Ethernet port • One ADSL over ISDN port • One ISDN-BRI S/T port • Eight Fast Ethernet Switch ports • IEEE 802.11a and 802.
PAGE 30
Platform-Specific Information Cisco 1812 Routers The Cisco 1812 router has the following hardware components: • Two Fast Ethernet ports • One ISDN-BRI S/T port • Eight Fast Ethernet switch ports • Two USB connectors Cisco 1841 router The Cisco 1841 router supports any combination of one or two of the following WAN interface cards (WICs) or multiflex Voice/WAN interface cards (VWICs) (data only), which are shared with the Cisco 1700, Cisco 2600, and Cisco 3600 series routers: • WIC-1T: one-port hig
PAGE 31
Platform-Specific Information • VWIC-2MFT-T1: two-port RJ-48 multiflex trunk (T1) • VWIC-2MFT-E1-DI: two-port RJ-48 multiflex trunk (E1) (with drop and insert) • VWIC-2MFT-T1-DI: two-port RJ-48 multiflex trunk (T1) (with drop and insert) • VWIC2-1MFT-T1/E1 • VWIC2-2MFT-T1/E1 • VWIC2-1MFT-G703 • VWIC2-2MFT-G703 AIM-VPN/BPII-PLUS: DES/3DES/AES VPN Encryption/Compression card is also supported on the Cisco 1841. AIM-VPN/SSL-1 Encryption Module is supported on the Cisco 1841.
PAGE 32
Platform-Specific Information Cisco 1805 Cable Router This section contains the following sections with information that is specific to the Cisco 1805 cable router: • Introduction, page 38 • Memory Recommendations, page 38 • Supported Hardware, page 38 • Feature Support, page 38 Introduction Cisco 1805 DOCSIS cable routers are fixed-configuration routers with LAN and WAN connections.
PAGE 33
Platform-Specific Information Cisco IAD2430 Series This section contains the following sections with information that is specific to the Cisco IAD2430 series routers: • Introduction, page 39 • Memory Recommendations, page 39 • Supported Hardware, page 39 • Feature Support, page 41 Introduction The Cisco IAD2430 is the next generation integrated voice and data services platform for Service Providers, building on the Cisco IAD2420 series IAD.
PAGE 34
Platform-Specific Information Table 1 Supported Interfaces on the Cisco IAD2430 Series Integrated Access Devices Interface and Port Product Description Supported IAD2430 Models 10/100BASE-T Fast Ethernet port All Cisco IAD2430 series models have two 10/100BASE-T Fast Ethernet ports except for Cisco2431-8FXS IAD, which has one. All Console and auxiliary ports One EIA/TIA-32 asynchronous serial port for connection to a console. All One EIA/TIA-32 asynchronous serial port for connection to a modem.
PAGE 35
Platform-Specific Information • VIC2-2FXS • VIC-4FXS/DID • VIC2-2BRI-NT/TE • WIC-1T • WIC-1ADSL • WIC-1SHDSL • WIC-1ADSL-DG • WIC-1SHDSL-V2 • VWIC-2MFT-T1 • VWIC-2MFT-E1 Feature Support For feature support in Cisco IOS Release 12.4T, see the “Feature Support” section on page 7. Release Notes for Cisco IOS Release 12.4T OL-8012-09 Rev.
PAGE 36
Platform-Specific Information Cisco 2600XM Series and Cisco 2691 Modular Access Routers This section contains the following sections with information that is specific to the Cisco 2600XM series and Cisco 2691 modular access routers: • Introduction, page 42 • Memory Recommendations, page 42 • Supported Hardware, page 42 • Other Firmware Code, page 49 • Feature Support, page 49 Introduction With the Cisco 2600 series modular access router family, Cisco extends enterprise-class and managed services
PAGE 37
Platform-Specific Information Table 2 lists the supported interfaces for the Cisco 2600 series routers for Cisco IOS Release 12.4T.
PAGE 38
Platform-Specific Information Table 2 Supported Interfaces for the Cisco 2600 Series Routers (Continued) Interface, Network Module, or Data Rate1 Digital T1 Packet Voice Trunk Network Modules and Spare Components Product Description Supported Platforms 1-port 24-channel T1 voice/fax module supports 24 channels All Cisco 2600 series platforms of medium-complexity codecs (G.729a/b, G.726, G.711, and fax) or 12 channels of G.726, G.729, G.723.1, G.728, G.729a/b, G.711, and fax.
PAGE 39
Platform-Specific Information Table 2 Supported Interfaces for the Cisco 2600 Series Routers (Continued) Interface, Network Module, or Data Rate1 Dial, ISDN, and Channelized Serial Network Modules Product Description Supported Platforms 1-port High Speed Serial Interface (HSSI) network module Cisco 2691 1- or 2-port channelized T1/ISDN PRI (NM-1CT1, NM-2CT1) All Cisco 2600 series platforms 1- or 2-port channelized T1/ISDN PRI with CSU (NM-1CT1-CSU, NM-2CT1-CSU) All Cisco 2600 series platforms 1-
PAGE 40
Platform-Specific Information Table 2 Supported Interfaces for the Cisco 2600 Series Routers (Continued) Interface, Network Module, or Data Rate1 T1/E1 Multiflex Voice/WAN Interface Cards3 Product Description Supported Platforms 1-port T1 multiflex trunk interface (VWIC-1MFT-T1) All Cisco 2600 series platforms 1-port E1 multiflex trunk interface (VWIC-1MFT-E1) All Cisco 2600 series platforms 2-port T1 multiflex trunk interface (VWIC-2MFT-T1) All Cisco 2600 series platforms 2-port E1 multiflex tr
PAGE 41
Platform-Specific Information Table 2 Supported Interfaces for the Cisco 2600 Series Routers (Continued) Interface, Network Module, or Data Rate1 Product Description Supported Platforms Voice/Fax Interface Cards 1- or 2-port voice/fax network module (NM-1V, NM-2V, NM-HD-1V, NM-HD-2V, NM-HD-2VE) All Cisco 2600 series platforms Cisco Unity Express voice mail network module (NM-CUE) Cisco 2610XM, Cisco 2611XM, Cisco 2620XM, Cisco 2621XM, Cisco 2650XM, Cisco 2651XM Cisco 2691 1-slot high-density T1/E1 V
PAGE 42
Platform-Specific Information Table 2 Supported Interfaces for the Cisco 2600 Series Routers (Continued) Interface, Network Module, or Data Rate1 Product Description Supported Platforms 1-port ADSL over POTS with dying gasp (WIC-1ADSL-DG) Cisco 2610XM, Cisco 2611XM, Cisco 2620XM, Cisco 2621XM, Cisco 2650XM, Cisco 2651XM Cisco 2691 Advanced Integration Module Content Engine Network Modules 1-port G.
PAGE 43
Platform-Specific Information 4. Uses the VWIC-MFT T1/E1 interface cards. 5. Requires the NM-1V or NM-2V network module. Other Firmware Code The latest version of analog modem firmware for the Cisco 2600 series supports the internal analog modems (both NM-16AM and NM-8AM) in a wide range of countries, starting with Cisco IOS Release 11.3(5)T. The latest firmware (version 1.2.0) also supports dial-out and fax-out. Additional information can be found on Cisco.
PAGE 44
Platform-Specific Information Cisco 2800 Series Routers This section contains the following sections with information that is specific to the Cisco 2800 series routers: • Introduction, page 50 • Memory Recommendations, page 50 • Supported Hardware, page 50 • Feature Support, page 57 • Additional Notes for the Cisco 2800 Series Routers, page 57 Introduction Cisco IOS Release 12.4T supports the Cisco 2800 series integrated services routers.
PAGE 45
Platform-Specific Information • Cisco 2811 • Cisco 2821 • Cisco 2851 For detailed descriptions of the new hardware features, see the “New and Changed Information” section on page 101. For additional information about supported hardware for this platform and release, see the Cisco Software Advisor at the following location: http://tools.cisco.com/Support/Fusion/FusionHome.do Table 3 lists the supported interfaces for the Cisco 2800 series routers for Cisco IOS Release 12.4 T.
PAGE 46
Platform-Specific Information Table 3 Supported Modules and Interface Cards for the Cisco 2800 Series Routers (Continued) Network Module Product Description Supported Platforms NM-4A/S 4-port asynchronous/synchronous serial network module Cisco 2811, Cisco 2821, Cisco 2851 NM-8A/S 8-port asynchronous/synchronous serial network module Cisco 2811, Cisco 2821, Cisco 2851 NM-16A/S 16-port asynchronous/synchronous serial network module Cisco 2811, Cisco 2821, Cisco 2851 NM-16A 16-port asynchronou
PAGE 47
Platform-Specific Information Table 3 Supported Modules and Interface Cards for the Cisco 2800 Series Routers (Continued) Network Module Product Description Supported Platforms NM-HDV2 IP communications high-density voice and fax network module Cisco 2811, Cisco 2821, Cisco 2851 NM-HDV2-1T1/E1 1-port T1/E1 IP communications high-density voice and fax Cisco 2811, Cisco 2821, network module Cisco 2851 NM-HDV2-2T1/E1 2-port T1/E1 IP communications high-density voice and fax Cisco 2811, Cisco 2821,
PAGE 48
Platform-Specific Information Table 3 Supported Modules and Interface Cards for the Cisco 2800 Series Routers (Continued) Network Module Product Description Supported Platforms NM-CUE Cisco Unity Express voice-mail network module Cisco 2811, Cisco 2821, Cisco 2851 NM-NAM Cisco 2600, 3660, 3700 series network analysis module Cisco 2811, Cisco 2821, Cisco 2851 Alarm Monitoring and Control Network Modules and Accessories NM-AIC-64 Alarm monitoring and control network module Cisco 2811, Cisco 282
PAGE 49
Platform-Specific Information Table 3 Supported Modules and Interface Cards for the Cisco 2800 Series Routers (Continued) Network Module Product Description Supported Platforms WIC-1B-U-V2 1-port ISDN BRI with integrated NT1 (U interface) All Cisco 2800 series platforms WIC-1B-S/T-V3 1-port ISDN BRI with S/T interface All Cisco 2800 series platforms WIC-1ADSL 1-port asymmetric DSL (ADSL) over POTS service WIC All Cisco 2800 series platforms WIC-1ADSL-DG 1-port ADSL over basic telephone servi
PAGE 50
Platform-Specific Information Table 3 Supported Modules and Interface Cards for the Cisco 2800 Series Routers (Continued) Network Module Product Description Supported Platforms VIC-1J1 1-port digital VIC 1J1 for Japan Cisco 2811, Cisco 2821, Cisco 2851 VIC-4FXS/DID 4-port FXS or DID VIC All Cisco 2800 series platforms VIC2-2FXS 2-port VIC-FXS All Cisco 2800 series platforms VIC2-2FXO 2-port VIC-FXO (universal) All Cisco 2800 series platforms VIC2-4FXO 4-port VIC-FXO (universal) All Cisco
PAGE 51
Platform-Specific Information Feature Support For feature support in Cisco IOS Release 12.4T, see the “Feature Support” section on page 7. Additional Notes for the Cisco 2800 Series Routers This section contains important information about using the Cisco 2800 series routers with Cisco IOS Release 12.4T software. BGP in IP Base BGP is available in the “IP base” software package for Cisco 1841, Cisco 2800 family, and Cisco 3800 family routers. Release Notes for Cisco IOS Release 12.4T OL-8012-09 Rev.
PAGE 52
Platform-Specific Information Cisco 3200 Series Rugged Integrated Service Routers This section contains the following sections with information that is specific to the Cisco 3200 series rugged integrated service routers (ISR): • Introduction, page 58 • Memory Recommendations, page 58 • Supported Hardware, page 58 • Feature Support, page 59 • Additional Notes for the Cisco 3200 Series Rugged Integrated Service Routers, page 59 Introduction The Cisco 3200 series rugged integrated service routers (f
PAGE 53
Platform-Specific Information The following Cisco cards are supported on the Cisco 3200 series routers: • The Mobile Access Router Card (MARC), which includes the host processor, memory, one 10/100 Ethernet port, one console port, and one auxiliary port. • The Serial Mobile Interface Card (SMIC), which supports either two or four synchronous/asynchronous serial ports. • The Fast Ethernet Switch Mobile Interface Card (FESMIC), which supports either two or four autosensing switched ports and LEDs.
PAGE 54
Platform-Specific Information Cisco 3600 Series Routers This section contains the following sections with information that is specific to the Cisco 3600 series routers: • Introduction, page 60 • Memory Recommendations, page 60 • Supported Hardware, page 60 • Feature Support, page 66 • Additional Notes for the Cisco 3600 Series Routers, page 66 Introduction The Cisco 3600 series comprises the Cisco 3631and Cisco 3660 routers.
PAGE 55
Platform-Specific Information Table 4 Supported Interfaces for the Cisco 3600 Series Routers Interface, Network Module, or Data Rate Dial Access Network Modules LAN Interfaces Fast Ethernet Switch Network Modules Product Description Supported Platforms 16- and 32-port asynchronous (NM-16A and NM-32A) Cisco 3631and Cisco 3660 4- and 8-port synchronous/asynchronous (NM-4A/S and NM-8A/S) Cisco 3631and Cisco 3660 6- to 30-port integrated digital modems network modules (NM-6DM, NM-12-DM, NM-18DM, NM-
PAGE 56
Platform-Specific Information Table 4 Supported Interfaces for the Cisco 3600 Series Routers (Continued) Interface, Network Module, or Data Rate Product Description Supported Platforms Mixed Media Network Modules 1-port 10/100BASE-TX with 1-port channelized/PRI/E1 balanced mode (NM-1FE1CE1B) Cisco 3660 only 1-port 10/100BASE-TX with 1-port channelized/PRI/E1 unbalanced mode (NM-1FE1CE1U) Cisco 3660 only 1-port 10/100BASE-TX with 1-port channelized/PRI/T1 (NM-1FE1CT1) Cisco 3660 only 1-port 10/1
PAGE 57
Platform-Specific Information Table 4 Supported Interfaces for the Cisco 3600 Series Routers (Continued) Interface, Network Module, or Data Rate Multiport T1/E1 ATM Network Modules with Inverse Multiplexing over ATM (IMA)2 Product Description Supported Platforms 1-port ATM-25 network modules (NM-1ATM-25) 1-port ATM T3 network module (NM-1A-T3) 2 Cisco 3660 only 2 Cisco 3660 only 4-port T1 ATM network module with IMA (NM-4T1-IMA) Cisco 3631 and Cisco 3660 4-port E1 ATM network module with IMA (N
PAGE 58
Platform-Specific Information Table 4 Supported Interfaces for the Cisco 3600 Series Routers (Continued) Interface, Network Module, or Data Rate Digital T1/E1 Packet Voice Trunk Network Modules and Spare Components Product Description Supported Platforms 1-port, 24-channel T1 voice/fax module supports 24 channels Cisco 3660 only of medium-complexity codecs: G.729a/b, G.726, G.711, and fax; or 12 channels of G.726, G.729, G.723.1, G.728, G.729a/b, G.711, and fax.
PAGE 59
Platform-Specific Information Table 4 Supported Interfaces for the Cisco 3600 Series Routers (Continued) Interface, Network Module, or Data Rate T1/E1 Multiflex Voice/WAN Interface Cards Voice/Fax Interfaces and Network Modules3 WAN Data Rates ISDN Channelized and Serial Network Modules Product Description Supported Platforms 1-port T1 multiflex trunk interface (VWIC-1MFT-T1) Cisco 3631 and Cisco 3660 1-port E1 multiflex trunk interface (VWIC-1MFT-E1) Cisco 3631 and Cisco 3660 2-port T1 multifl
PAGE 60
Platform-Specific Information Table 4 Supported Interfaces for the Cisco 3600 Series Routers (Continued) Interface, Network Module, or Data Rate Product Description Supported Platforms WAN Interface Cards 1-Port ADSL WAN interface card (WIC) Cisco 3660 only 1-port T1/fractional T1/DSU/CSU WIC (WIC-1DSU-T1) Cisco 3660 only 1-port T1/fractional T1 56/64-kbps DSU/CSU WIC (WIC-1DSU-56K4) Cisco 3631 and Cisco 3660 1-port ISDN with NT-1 WIC (BRI WIC)6 Cisco 3631 and Cisco 3660 1-port ISDN WIC (WIC-
PAGE 61
Platform-Specific Information behaviors are xxx000, with the values of xxx ranging from 1 to 7 and the code points called Class Selector Code Points (cs1-cs7 in the command shown above). The default value is 000000 for media and signaling. Two other RFCs have also defined PHBs. RFC 2597 defines the Assured Forwarding PHB Group. With Assured Forwarding (af11-af43), bits 0 to 2 represent the class of traffic stream, and bits 3 to 5 represent the drop priority of a traffic stream.
PAGE 62
Platform-Specific Information Cisco 3700 Series Routers This section contains the following sections with information that is specific to the Cisco 3700 series routers: • Memory Recommendations, page 68 • Supported Hardware, page 68 • Feature Support, page 72 Memory Recommendations For memory recommendations for the Cisco 3700 series routers in Cisco IOS Release 12.4T, see the “Memory Recommendations” section on page 8. Supported Hardware Cisco IOS Release 12.
PAGE 63
Platform-Specific Information Table 5 Supported Interfaces for the Cisco 3700 Series Routers (Continued) Network Modules, VICs, and AIMs Product Description Supported Platforms NM-2FE2W 2-port 10/100 Ethernet 2 WAN card slot network module All Cisco 3700 series platforms 1-port Fast Ethernet network module (10/100BASE fiber only) All Cisco 3700 series platforms NM-1FE-FX 1 Digital Packet Voice and Fax Trunk Network Modules NM-HDV-1T1-12 High density voice network module, with 1 VWIC-1MFT-T1 A
PAGE 64
Platform-Specific Information Table 5 Supported Interfaces for the Cisco 3700 Series Routers (Continued) Network Modules, VICs, and AIMs Product Description Supported Platforms AIM-VPN/SSL-3 Encryption module support All Cisco 3700 series platforms AIM-VOICE-30 30-channel DSP AIM All Cisco 3700 series platforms AIM-ATM-VOICE-30 ATM SAR with 30-channel DSP AIM All Cisco 3700 series platforms Analog Packet Voice and Fax Trunk NM-1V 1-slot voice and fax network module All Cisco 3700 series pl
PAGE 65
Platform-Specific Information Table 5 Supported Interfaces for the Cisco 3700 Series Routers (Continued) Network Modules, VICs, and AIMs Product Description Supported Platforms WIC-1T 1-port serial All Cisco 3700 series platforms WIC-2T 2-port serial All Cisco 3700 series platforms WIC-2-A/S 2-port synchronous/asynchronous (maximum speed 128 kbps) All Cisco 3700 series platforms WIC-1DSU-56K4 1-port, 4-wire 56/64-kbps with CSU/DSU All Cisco 3700 series platforms WIC-1DSU-T1 1-port T1 CSU/
PAGE 66
Platform-Specific Information Table 5 Supported Interfaces for the Cisco 3700 Series Routers (Continued) Network Modules, VICs, and AIMs Product Description Supported Platforms NM-8B-S/T 8-port ISDN BRI network module (S/T interface) All Cisco 3700 series platforms NM-8B-U 8-port ISDN BRI with NT1 network module (U interface) All Cisco 3700 series platforms WIC-1AM 1-port analog modem WIC All Cisco 3700 series platforms WIC-2AM 2-port analog modem WIC All Cisco 3700 series platforms NM-6DM
PAGE 67
Platform-Specific Information Cisco 3800 Series Routers This section contains the following sections with information that is specific to the Cisco 3800 series routers: • Introduction, page 73 • Memory Recommendations, page 74 • Supported Hardware, page 74 • Feature Support, page 80 • Additional Notes for the Cisco 3800 Series Routers, page 81 Introduction Cisco 3800 series integrated services routers are part of a new generation of routers that incorporate high-performance integrated data, voice
PAGE 68
Platform-Specific Information Memory Recommendations For memory recommendations for the Cisco Catalyst 4224 Access Gateway Switch in Cisco IOS Release 12.4T, see the “Memory Recommendations” section on page 8. Supported Hardware Cisco IOS Release 12.4T supports the following Cisco 3800 series routers: • Cisco 3825 • Cisco 3845 For detailed descriptions of the new hardware features, see the “New and Changed Information” section on page 101.
PAGE 69
Platform-Specific Information Table 6 WAN, LAN, and Voice Connections for the Cisco 3800 Series Routers (Continued) Port or Connection Port Type Connected To T1/FT1 CSU/DSU 8-pin modular RJ-48C interface Gigabit Ethernet SFP, optical LC 1000BASE-SX, -LX, -LH, -ZX, -CWDM Table 7 lists the supported interfaces for the Cisco 3800 series routers for Cisco IOS Release 12.4T.
PAGE 70
Platform-Specific Information Table 7 Supported Interfaces for the Cisco 3800 Series Routers (Continued) Network Module, WIC, VWIC, VIC, AIM, or PVDM Product Description Supported Platforms ILPM4 In-line power daughter card for the HWIC-4ESW with 802.3af All Cisco 3800 series platforms capability ILPM8 In-line power daughter card for the HWIC-9ESW with 802.
PAGE 71
Platform-Specific Information Table 7 Supported Interfaces for the Cisco 3800 Series Routers (Continued) Network Module, WIC, VWIC, VIC, AIM, or PVDM Product Description Supported Platforms Analog Dialup and Remote Access Network Modules NM-8AM-V2 8-port analog modem network module with v.92 All Cisco 3800 series platforms NM-16AM-V2 16-port analog modem network module with v.
PAGE 72
Platform-Specific Information Table 7 Supported Interfaces for the Cisco 3800 Series Routers (Continued) Network Module, WIC, VWIC, VIC, AIM, or PVDM Product Description Supported Platforms NM-HDV-2E1-60 2-port 60-channel E1 voice and fax network module; bundle: NM-HDV with 1 VWIC-2MFT-E1-DI and 5 PVDM-12s All Cisco 3800 series platforms NM-HDV-1J1-30 1-port 30-channel J1 high-density voice network module; bundle: NM-HDV with 3 PVDM-12s and 1 VIC-1J1 All Cisco 3800 series platforms NM-HDV-1J1-30E
PAGE 73
Platform-Specific Information Table 7 Supported Interfaces for the Cisco 3800 Series Routers (Continued) Network Module, WIC, VWIC, VIC, AIM, or PVDM Product Description Supported Platforms Channel Service Unit/Data Service Unit (CSU/DSU) WICs WIC-1DSU-T1-V2 1-port T1/Fractional-T1 DSU/CSU WIC All Cisco 3800 series platforms WIC-1DSU-56K4 1-port 4-wire 56-/64-kbps CSU/DSU WIC All Cisco 3800 series platforms WIC-1B-S/T-V3 1-port ISDN BRI WIC for dial and lease line All Cisco 3800 series platfor
PAGE 74
Platform-Specific Information Table 7 Supported Interfaces for the Cisco 3800 Series Routers (Continued) Network Module, WIC, VWIC, VIC, AIM, or PVDM Product Description Supported Platforms EC-MFT-32 32-channel multiflex trunk dedicated ECAN module All Cisco 3800 series platforms EC-MFT-64 64-channel multiflex trunk dedicated ECAN module All Cisco 3800 series platforms Gigabit Ethernet High-Speed WIC HWIC-1GE-SFP Cisco Gigabit Ethernet high-speed interface card All Cisco 3800 series platforms
PAGE 75
Platform-Specific Information Additional Notes for the Cisco 3800 Series Routers This section contains important information about using the Cisco 3800 series routers with Cisco IOS Release 12.4T software. BGP in IP Base BGP is available in the “IP base” software package for Cisco 1841, Cisco 2800 family, and Cisco 3800 family routers. Release Notes for Cisco IOS Release 12.4T OL-8012-09 Rev.
PAGE 76
Platform-Specific Information Cisco AS5350 and Cisco AS5350XM Universal Gateways This section contains the following sections with information that is specific to the Cisco AS5350 and Cisco AS5350XM universal gateways: • Introduction, page 82 • Memory Recommendations, page 82 • Supported Hardware, page 82 • Feature Support, page 83 Introduction The Cisco AS5350 universal gateway is the only one-rack unit, two-, four-, or eight- PRI gateway that provides universal services—data, voice, and fax servi
PAGE 77
Platform-Specific Information Table 8 Supported Interfaces for the Cisco AS5350 Universal Gateways (Continued) Interfaces and Dial Feature Cards Product Description Trunk/Backhaul Interface Options CT3 DFC 2PRI CT1/CE1 DFC, 4PRI CT1/CE1 DFC, 8PRI CT1/CE1 DFC Two 8-MB serial ports 1. The dial-only dial feature card (DFC) is supported on the Cisco AS5xxxXM gateways only. 2. The Cisco AS5xxxXM gateways support the Gigabit Ethernet Interface. Feature Support For feature support in Cisco IOS Release 12.
PAGE 78
Platform-Specific Information Cisco AS5400, Cisco AS5400HPX, and AS5400XM Universal Gateways This section contains the following sections with information that is specific to the Cisco AS5400, Cisco AS5400HPX, and Cisco AS5400XM universal gateways: • Introduction, page 84 • Memory Recommendations, page 84 • Supported Hardware, page 84 • Feature Support, page 85 Introduction The Cisco AS5400 universal gateway is a two-rack unit, 8-, 12-, or 16-T1/E1, 1-CT3 gateway that provides universal port data,
PAGE 79
Platform-Specific Information Table 9 Supported Interfaces for the Cisco AS5400 Universal Gateways (Continued) Interfaces and Dial Feature Cards Product Description LAN Interfaces Fast Ethernet 10/100BASE-T (RJ-45) Gigabit Ethernet 10/100/1000BASE-T (RJ-45)2 Trunk/Backhaul Interface Options 2PRI CT1/CE1 DFC, 4PRI CT1/CE1 DFC, 8PRI CT1/CE1 DFC CT3 DFC 2 serial ports on the motherboard 1. The dial-only dial feature card (DFC) is supported on the Cisco AS5xxxXM gateways only. 2.
PAGE 80
Platform-Specific Information Cisco AS5850 Universal Gateways This section contains the following sections with information that is specific to the Cisco AS5850 universal gateway: • Introduction, page 86 • Memory Recommendations, page 86 • Supported Hardware, page 86 • Feature Support, page 87 Introduction The Cisco AS5850 universal gateway provides the highest concentration of port and ISDN terminations available in a single remote access server product.
PAGE 81
Platform-Specific Information Table 10 Supported Feature Boards for the Cisco AS5850 Universal Gateway (Continued) Feature Boards Product Description WAN Interface Options Channelized T1 (AS58-24CT1) Channelized T3 (AS58-1CT3/216U) Channelized E1 (AS58-24CE1) Channelized STM1 (AS58-STM1) 1. The Fast Ethernet is for management purposes only. Feature Support For feature support in Cisco IOS Release 12.4T, see the “Feature Support” section on page 7. Release Notes for Cisco IOS Release 12.
PAGE 82
Platform-Specific Information Cisco Catalyst 6000/Cisco 7600 Multiprocessor WAN Application Module This section contains the following sections with information that is specific to the Cisco Catalyst 6000/Cisco 7600 multiprocessor WAN application module: • Introduction, page 88 • Memory Recommendations, page 88 • Supported Hardware, page 88 • Feature Support, page 88 Introduction The Cisco multiprocessor WAN application module (MWAM) provides three processor complexes with dual processors used in t
PAGE 83
Platform-Specific Information Cisco Catalyst 6500/Cisco 7600 Communication Media Module This section contains the following sections with information that is specific to the Cisco Catalyst 6500/Cisco 7600 communication media module: • Introduction, page 89 • Memory Recommendations, page 89 • Supported Hardware, page 89 • Feature Support, page 91 • Additional Notes for the Cisco Catalyst 6500/Cisco 7600 Communication Media Module, page 91 Introduction Cisco communication media module voice feature
PAGE 84
Platform-Specific Information Cisco IOS Support Note • CMM has its own software image; the image is not bundled with the supervisor engine or MSFC images. See the “Additional Notes for the Cisco Catalyst 6500/Cisco 7600 Communication Media Module” section on page 91 for instructions on downloading the image to the CMM flash memory. • Supervisor Engine 720 requires the CMM to run Cisco IOS Release 12.3(8)XY4 or a later release.
PAGE 85
Platform-Specific Information Feature Support For feature support in Cisco IOS Release 12.4T, see the “Feature Support” section on page 7. Additional Notes for the Cisco Catalyst 6500/Cisco 7600 Communication Media Module This section contains important information about using the Cisco Catalyst 6500/Cisco 7600 Communication Media Module with Cisco IOS Release 12.4T software. Release Upgrade Notice The CMM wscmm-i6s-mz.123-14.T image contains a new bundle 4.4.X DSPware infrastructure.
PAGE 86
Platform-Specific Information Cisco 7000 Series Routers This section contains the following sections with information that is specific to the Cisco 7000 series router: • Memory Recommendations, page 92 • Supported Hardware, page 92 • Feature Support, page 92 Memory Recommendations For memory recommendations for the Cisco 7000 series routers in Cisco IOS Release 12.4T, see the “Memory Recommendations” section on page 8. Supported Hardware Cisco IOS Release 12.
PAGE 87
Platform-Specific Information Cisco 7600 Service and Application Module for IP (SAMI) This section contains the following sections with information that is specific to the Cisco 7600 SAMI: • Introduction, page 93 • Memory Recommendations, page 93 • Supported Hardware, page 93 • Feature Support, page 93 Introduction The Cisco Service and Application Module for IP (SAMI) is a high performance, Cisco IOS software application module that occupies one slot in the Cisco 7600 series router platform.
PAGE 88
Platform-Specific Information Cisco IGX 8400 Series URM This section contains the following sections with information that is specific to the Cisco IGX 8400 series Universal Router Module (URM): • Introduction, page 94 • Memory Recommendations, page 94 • Supported Hardware, page 94 • Feature Support, page 96 Introduction Cisco has supported the Cisco IGX 8400 series platforms since Cisco IOS Release 12.1(5)YA.
PAGE 89
Platform-Specific Information IGX Switches Like other Cisco WAN switches, the IGX switch operates in public or private WANs. An IGX switch can support OC-3, T3, E3, T1, E1, inverse multiplexing over ATM (IMA) for T1 or E1, fractional T1 or E1, or subrate digital transmission facilities. The IGX cell relay technology provides maximum throughput with minimum delays.
PAGE 90
Platform-Specific Information The following option is for a data-only back card: – BC-URI-2FE, providing two 10/100BASE-T Fast Ethernet ports (RJ-45) and one console port (RJ-45) The URM can connect to another Cisco router in the following ways: • Through its 155-Mbps ATM interface to the IGX backplane (ATM-to-ATM [URM-to-UXM] or ATM/FR SIW [URM-to-UFM] connections can be established with SWSW) • Through its two Fast Ethernet ports • Through its two T1 or E1 ports (only on the data/voice back cards)
PAGE 91
Platform-Specific Information Cisco MGX 8850 Route Processor Modules (RPM-PR and RPM-XF) This section contains the following sections with information that is specific to the Cisco MGX 8850 Route Processor Module: • Memory Recommendations, page 97 • Feature Support, page 97 Memory Recommendations For memory recommendations for the Cisco MGX 8850 in Cisco IOS Release 12.4T, see the “Memory Recommendations” section on page 8. Feature Support For feature support in Cisco IOS Release 12.
PAGE 92
Platform-Specific Information Cisco Signaling Link Terminals This section contains the following sections with information that is specific to the Cisco Signaling Link Terminal: • Introduction, page 98 • Memory Recommendations, page 99 • Supported Hardware, page 99 • Feature Support, page 100 Introduction The Cisco Signaling Link Terminal (SLT) enables service providers to reliably transport Signaling System 7 (SS7) protocols across an IP network.
PAGE 93
Platform-Specific Information Memory Recommendations For memory recommendations for the Cisco Signaling Link Terminal in Cisco IOS Release 12.4T, see the “Memory Recommendations” section on page 8. Supported Hardware The Cisco SLT feature in Cisco IOS Release 12.4T supports the Cisco 2611XM and Cisco 2651XM routers exclusively. The Cisco SLT feature is not supported with any other Cisco 2600 series chassis. For more information about the Cisco 2600 series in Cisco IOS Release 12.
PAGE 94
Platform-Specific Information Feature Support For feature support in Cisco IOS Release 12.4T, see the “Feature Support” section on page 7. Release Notes for Cisco IOS Release 12.4T 100 OL-8012-09 Rev.