4025561 Rev A Prisma II EMS Remote User Interface Guide - System Release 2.
For Your Safety Explanation of Warning and Caution Icons Avoid personal injury and product damage! Do not proceed beyond any symbol until you fully understand the indicated conditions. The following warning and caution icons alert you to important information about the safe operation of this product: You may find this symbol in the document that accompanies this product. This symbol indicates important operating or maintenance instructions. You may find this symbol affixed to the product.
Notices Trademark Acknowledgments Cisco, the Cisco logo, Cisco Systems, the Cisco Systems logo, Scientific Atlanta, the Scientific Atlanta logo, Prisma, Prisma II, and SciCare are trademarks or registered trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. All other trademarks mentioned in this document are property of their respective owners. Publication Disclaimer Cisco Systems, Inc.
Contents Prisma II Product Notices vii Important Safety Instructions ix Laser Safety Chapter 1 Introduction xvii 1 Related Publications ................................................................................................................ 3 What's New............................................................................................................................... 5 Chapter 2 CLI Overview 7 Prisma II Enhanced Platform Management Configuration ..................................
Contents alarm domain ......................................................................................................................... 45 alarm module ......................................................................................................................... 46 chassis ...................................................................................................................................... 47 exit............................................................................
Contents show eventlogfilter .............................................................................................................. 138 show file ................................................................................................................................ 139 show ike ................................................................................................................................ 140 show iproute......................................................................
Contents Return Product for Repair .................................................................................................. 214 Appendix A Prisma II Permitted CLI Commands 221 From CLI ............................................................................................................................... 222 From ICIM............................................................................................................................. 223 From */* MODULE ..........................
Prisma II Product Notices Prisma II Product Notices System Release The information in this guide pertains to System Release 2.04.01 of the Prisma II Enhanced Management System platform. Operating Temperature CAUTION: The warranty may be voided and the equipment damaged if you operate the equipment above the specified temperature limits (131°F/55°C for postamplifiers, 149°F/65°C for other products).
Important Safety Instructions Important Safety Instructions Read and Retain Instructions Carefully read all safety and operating instructions before operating this equipment, and retain them for future reference. Follow Instructions and Heed Warnings Follow all operating and use instructions. Pay attention to all warnings and cautions in the operating instructions, as well as those that are affixed to this equipment. Terminology The terms defined below are used in this document.
Important Safety Instructions - Only qualified service personnel are allowed to perform equipment installation or replacement. - Only qualified service personnel are allowed to remove chassis covers and access any of the components inside the chassis. Grounding - Prisma II equipment is suitable for installation as part of the common bonding network (CBN). - Do not violate the protective grounding by using an extension cable, power cable, or autotransformer without a protective ground conductor.
Important Safety Instructions Do not install near any heat sources such as radiators, heat registers, stoves, or other equipment (including amplifiers) that produce heat. Place this equipment close enough to a DC input voltage source to accommodate the length of this equipment’s power cord. Route all power cords so that people cannot walk on, place objects on, or lean objects against them. This may pinch or damage the power cords.
Important Safety Instructions CAUTION: Installation of this equipment in a rack should be such that the amount of airflow required for safe operation of this equipment is not compromised. Elevated Operating Ambient Temperature Only install this equipment in a humidity- and temperature-controlled environment that meets the requirements given in this equipment’s technical specifications.
Important Safety Instructions Connection to -48 V DC/-60 V DC Power Sources If this equipment is DC-powered, refer to the specific installation instructions in this manual or in companion manuals in this series for information on connecting this equipment to nominal -48 V DC/-60 V DC power sources. Circuit Overload Know the effects of circuit overloading before connecting this equipment to the power supply.
Important Safety Instructions Moisture - Do not allow moisture to enter this equipment. Cleaning - Use a damp cloth for cleaning. Safety Checks - After service, assemble this equipment and perform safety checks to ensure it is safe to use before putting it back into operation. Electrostatic Discharge Electrostatic discharge (ESD) results from the static electricity buildup on the human body and other objects. This static discharge can degrade components and cause failures.
Important Safety Instructions The batteries may contain substances that could be harmful to the environment Recycle or dispose of batteries in accordance with the battery manufacturer’s instructions and local/national disposal and recycling regulations. The batteries may contain perchlorate, a known hazardous substance, so special handling and disposal of this product might be necessary. For more information about perchlorate and best management practices for perchlorate-containing substance, see www.
Important Safety Instructions the cable shielding. Exceptions from this general rule will be clearly stated in the connector description for the excepted connector in question. Ethernet cables should be of single-shielded or double-shielded type. Coaxial cables should be of the double-braided shielded type.
Laser Safety Laser Safety Introduction This equipment contains an infrared laser that transmits intensity-modulated light and emits invisible radiation. Warning: Radiation WARNING: Avoid personal injury! Use of controls, adjustments, or procedures other than those specified herein may result in hazardous radiation exposure. Avoid personal injury! The laser light source on this equipment (if a transmitter) or the fiber cables connected to this equipment emit invisible laser radiation.
Laser Safety Safe Operation for Software Controlling Optical Transmission Equipment If this manual discusses software, the software described is used to monitor and/or control ours and other vendors’ electrical and optical equipment designed to transmit video, voice, or data signals. Certain safety precautions must be observed when operating equipment of this nature. For equipment specific safety requirements, refer to the appropriate section of the equipment documentation.
Laser Safety Warning Labels One or more of the labels shown below are located on Prisma II Pre-Amplifiers, PostAmplifiers, Optical Transmitters, and Optical Switches.
Laser Safety Location of Labels on Equipment The following illustrations display the typical locations of warning labels on Prisma II Pre-Amplifiers, Post-Amplifiers, Optical Transmitters, and Optical Switches.
Laser Safety 4025561 Rev A xxi
Laser Safety xxii 4025561 Rev A
1 Chapter 1 Introduction Overview The Prisma II™ Enhanced Management System Intelligent Control Interface Module 2 (ICIM2) currently supports three methods of remote user access: Command Line Interface (CLI) ICIM Web Interface Simple Network Management Protocol (SNMP) This guide describes remote user access for the ICIM2 via CLI and the ICIM Web Interface. Remote access via SNMP is described in detail in the Prisma II Enhanced Management System Guide, System Release 2.04, part number 4025559.
Qualified Personnel Only appropriately qualified and skilled personnel should attempt to install, operate, maintain, and service this product. WARNING: Allow only qualified and skilled personnel to install, operate, maintain, and service this product. Otherwise, personal injury or equipment damage may occur. Scope This guide discusses the following topics.
Related Publications Related Publications You may find the following publications useful as you implement the procedures in this document. System Release 2.04 Prisma II Enhanced Management System Guide, System Release 2.04, part number 4025559 Prisma II Enhanced Management System Troubleshooting Guide, System Release 2.04, part number 4025560 Prisma II Transport System Release 2.04 Release Notes and Installation Instructions, part number 4027218 System Release 2.
Chapter 1 Introduction Prisma II™ Enhanced Management System Troubleshooting Guide - System Release 1.01, part number 4015396 Prisma II™ Transport System Release Notes, Release 1.01.
What's New What's New This section highlights the major differences between System Release 2.04 and the earlier System Release 2.01. Optical Switch Functionality System Release 2.04 provides new optical switch module firmware that changes the default nominal input power for Port 3 and Port 4 from 19 dBm to 21 dBm. Despite this change, the module type (devtype) remains the same as before at 4011.
2 Chapter 2 CLI Overview Introduction The command-line interface (CLI) for the Prisma II Intelligent Communications Interface Module 2 (ICIM2) allows for monitoring and control of the ICIM2 domain. The ICIM2 domain includes the ICIM2 itself, the chassis in which it is installed, and all other modules installed in the chassis and any daisy-chained chassis. The CLI is designed for use by both local craft operators and remote monitoring systems.
Chapter 2 CLI Overview Prisma II Enhanced Platform Management Configuration Local or Remote PC NMS Platform NMS Application SA Remote SW Downloader App (SOUP) FTP Server ICIM IN/OUT Ports Daisy Chain multiple chassis ICIM2 Optical Module Optical Module Power Supply & Fan Tray Configuration & Management Bus Enet Ethernet Prisma II Chassis Local PC CLI Interface Hyperterm SW IP Network [Username/passwd Protection – Multiple Chassis] Com Ethernet TP386 8 4025561 Rev A
User Authorization User Authorization Access to the CLI is controlled by password-protected login. Each CLI user is granted access at one of three authorization levels: Authorization Level Description Admin Admin level users can add and delete users, change user passwords, and change IP addresses and other critical values. Readwrite Users with Readwrite access can view system parameter values as well as change most control and operating parameter values.
Chapter 2 CLI Overview CLI Login and Logout To use the CLI, you must first establish communication with a chassis in one of two ways: Use a serial connection (e.g., HyperTerminal) as described in the Prisma II Enhanced Management System Guide, System Release 2.04, part number 4025559. Use your element management system (see your network administrator for assistance).
CLI Login and Logout To Log Out To log out of the CLI and exit the session, type logout, and then press Enter. Note: The CLI recognizes the logout command at any command prompt, regardless of the current command mode. Important: For Telnet operation, the computer you are using must have a network connection through which it can reach the ICIM2 using its IP address. No more than four Telnet sessions are allowed at one time.
Chapter 2 CLI Overview CLI Command Modes All CLI interactions occur in one of four command modes. Command modes affect the scope of the commands as well as how they are interpreted. Mode Description CLI The default command mode at login, used for issuing CLI commands to perform general control and monitoring tasks. Module Used to issue Module mode commands, which are directed to a specific module or range of modules installed in the ICIM2 domain.
CLI Command Modes CLI> If desired, then change to icim command mode as follows: CLI> icim ICIM> You cannot change command modes directly, e.g., by typing terminal at the ICIM> prompt.
Chapter 2 CLI Overview Command Syntax To facilitate its use by both craft operators and remote monitoring systems, the CLI accepts commands in either of two formats: A modal command format allows craft operators to first select a command mode, and then use mode-specific commands and help screens. A non-modal command format allows an element management system (or a craft operator) to enter all command parameters, including command mode changes, on a single line.
Command Syntax 01/06 MODULE> In the first line of this example, the operator selects the Module command mode. In the next line, the prompt has changed to reflect the new command mode. The operator then selects chassis 1, slot 6 as the target for subsequent commands. On pressing Enter, the prompt then changes from */* MODULE> to 01/06 MODULE> to show the selection of chassis 1, slot 6 in effect. Next, the operator types the alarm module command.
Chapter 2 CLI Overview The CLI command line interpreter would then parse the command into the following sequence of instructions: Switch to Module command mode. Direct subsequent commands to chassis 1 in the current ICIM2 domain. Direct subsequent commands to slot 6 of the designated chassis in the current ICIM2 domain. Exit Module mode and return to CLI command mode following command execution. Display the alarm status of the specified device, i.e., the module occupying chassis 1, slot 6.
Command Syntax */* MODULE> chassis 20 slot * 20/* MODULE> show monitor outpwr MODID 20/05 20/07 20/13 NAME OutPwr OutPwr OutPwr VALUE -5.33429 10.086 -6.15736 UNITS dBm dBm dBm SUCCESS! 20/* MODULE> In the first line above, the operator changes from CLI command mode to Module command mode and specifies chassis 20, any (*) slot. In the next line, the prompt (20/* MODULE>) has changed to reflect the new command mode and chassis specification.
Chapter 2 CLI Overview General Hints and Help The CLI command information in this section applies regardless of the command or command mode currently in use. Shortcuts and Abbreviations The CLI interpreter recognizes shortcuts and abbreviations for certain commands. A shortcut is a single key or key combination (such as Ctrl-u) that is functionally equivalent to a longer command. Shortcuts are handy for craft operators because they reduce keystrokes, saving time and reducing the risk of a typing error.
General Hints and Help Shortcut Description ← Moves the cursor left. → Moves the cursor right. Note: This list can also be viewed in CLI by issuing the command help edit. An abbreviation is a truncated form of a command name. The CLI recognizes the shortest character string that uniquely identifies a command or parameter. For example, in CLI command mode, typing i (or ici, etc.) is recognized as equivalent to typing the icim command.
Chapter 2 CLI Overview Note: A summary of recognized CLI commands by command mode is provided in Prisma II Permitted CLI Commands (on page 221).
3 Chapter 3 CLI Mode Commands Introduction This chapter describes the commands that can be executed in CLI command mode. Some of the commands available in CLI command mode are global in scope, and give the same results whether entered in CLI mode or another command mode. In This Chapter 4025561 Rev A alarm ....................................................................................................... 22 clear...................................................................
Chapter 3 CLI Mode Commands alarm Syntax alarm Description The alarm command is used to display all active alarms in the domain of the ICIM2. This command produces the same results whether entered in CLI, Module, Terminal, or ICIM command mode. Note: This command is functionally equivalent to alarm domain (on page 45).
clear clear Syntax clear Description The clear command is used to clear the terminal display.
Chapter 3 CLI Mode Commands date Syntax date Description The date command is used to display the current date and time.
help help Syntax help modeOption Description The help command is used alone to display onscreen help for all CLI mode commands, or with a modeOption parameter to display help for a single command or function. Note: Typing a question mark (?) character at the CLI> command prompt gives the same result as typing help without a mode option parameter. Parameters The possible values for the modeOption parameter and their results are listed below.
Chapter 3 CLI Mode Commands Delete current character.....................Ctrl-d Delete text up to cursor.....................Ctrl-u Delete from cursor to end of line............Ctrl-k Move to beginning of line....................Ctrl-a Move to end of line..........................Ctrl-e Get prior command from history...............Ctrl-p Get next command from history................Ctrl-n Move cursor left.............................Ctrl-b Move cursor right............................
icim icim Syntax icim Description The icim command is used to change from CLI command mode to ICIM command mode. Parameters None Access Rights Required Read, ReadWrite, or Admin Examples CLI is the default command mode at login.
Chapter 3 CLI Mode Commands logout Syntax logout Description The logout command is used to terminate the current CLI session. This command is available in every command mode. Important: For Telnet operation, the computer you are using must have a network connection through which it can reach the ICIM2 using its IP address. No more than four Telnet sessions are allowed at one time. If IPsec is enabled on the ICIM2, it must also be enabled on the remote CLI user's computer.
logout logout (Terminal command mode) 4025561 Rev A 29
Chapter 3 CLI Mode Commands manual Syntax modeOption manual Description The manual command is used to display detailed help for CLI command mode, or for another command mode if specified by a preceding modeOption parameter. Parameters The possible values for the modeOption parameter and their results are listed below. modeOption Description Displays detailed help for CLI command mode. module Displays detailed help for Module command mode.
manual The interface uses modes: CLI, MODULE, TERMINAL, and ICIM. The prompt reflects the current mode. Enter the mode name to enter that mode, and use EXIT to leave the mode and return to CLI mode.
Chapter 3 CLI Mode Commands module Syntax module Description The module command is used to change from CLI command mode to Module command mode. Parameters None Access Rights Required Read, ReadWrite, or Admin Examples CLI is the default command mode at login.
terminal terminal Syntax terminal Description The terminal command is used to change from CLI command mode to Terminal command mode. Parameters None Access Rights Required Read, ReadWrite, or Admin Examples CLI is the default command mode at login.
Chapter 3 CLI Mode Commands who Syntax who Description The who command is used to display a list of the currently logged in users. Parameters None Access Rights Required Admin Example CLI> who LOGIN IDENTIFIER Administrat0r IP ADDRESS local console TYPE CLI LOGIN TIME 03/13/07 11:22:01 SUCCESS! CLI> Note: The value in the IP Address column indicates the IP address from which the remote user is connecting to the ICIM2.
whoami whoami Syntax whoami Description The whoami command is used to display the username of the current CLI user.
4 Chapter 4 Module Mode Commands Introduction This chapter describes the CLI commands that can be executed in the Module command mode.
Chapter 4 Module Mode Commands In This Chapter 38 Overview................................................................................................ 39 About Modspecs ................................................................................... 41 alarm ....................................................................................................... 44 alarm domain .........................................................................
Overview Overview Module mode commands allow for the control and monitoring of a selected module or range of modules. The scope of a Module mode command is defined using a special command called a module specification, or modspec. The Module mode command prompt always indicates the modspec currently in effect. For additional information, see About Modspecs (on page 41).
Chapter 4 Module Mode Commands To Access Module Command Mode The CLI only recognizes Module mode commands in Module command mode. Complete the following steps to enter Module command mode. 40 1 Confirm that you have logged onto CLI as explained in CLI Login and Logout (on page 10). 2 At the CLI> prompt, type Module, and then press Enter. 3 Confirm that the command prompt changes to X/Y MODULE> where X and Y are either *, a number, or a range of numbers in brackets.
About Modspecs About Modspecs Module specifications, or modspecs, are commands that specify a module or range of modules as targets for subsequent Module mode commands. The Module mode command prompt always reflects the modspec currently in effect. For this reason, the term modspec also loosely refers to the Module mode prompt itself.
Chapter 4 Module Mode Commands The following sample dialog illustrates the use of all three methods. Note how the Module mode prompt changes on each line to reflect the changing modspec. */* MODULE> chassis 10 (selects any slot in chassis 10) 10/* MODULE> chassis [2-87] (selects any slots in chassis 2-87) [02-87]/* MODULE> chassis * (selects all chassis and slots) */* MODULE> slot The slot command can be used to specify any of the following: A single slot, using the slot number (0-47).
About Modspecs Notes on Usage Modspecs stay in effect when exiting and re-entering Module command mode. However, modspecs do not affect the scope of CLI, ICIM, or Terminal mode commands. When specifying a range of chassis or slots, the specified range need not be fully populated. For example, the chassis range [1-7] is valid even if there are fewer than seven chassis within that range. In addition, all chassis within the specified range are included whether or not their chassis numbers are contiguous.
Chapter 4 Module Mode Commands alarm Syntax alarm Description The alarm command is used to display all active alarms in the domain of the ICIM2. This command produces the same results whether entered in CLI, Module, Terminal, or ICIM command mode. Note: This command is functionally equivalent to alarm domain (on page 45).
alarm domain alarm domain Syntax alarm domain Description The alarm domain command is used to display all active alarms in the domain of the ICIM2. Note: This command is functionally equivalent to the alarm command. Parameters None Access Rights Required Read, ReadWrite, or Admin Example 20/* MODULE> alarm domain No active alarms found SUCCESS! 20/* MODULE> This response indicates that no alarms are currently active anywhere in the ICIM2 domain.
Chapter 4 Module Mode Commands alarm module Syntax alarm module Description The alarm module command is used to display all active alarms in the range indicated by the Module prompt (modspec). Parameters None Access Rights Required Read, ReadWrite, or Admin Example 20/[5-7] MODULE> alarm module No active alarms found for the specified module range SUCCESS! 20/[5-7] MODULE> This response indicates that no alarms are currently active in modules 5, 6, or 7 of chassis 20 in the ICIM2 domain.
chassis chassis Syntax chassis chassisidvalue Description The chassis command is used to specify: A single chassis, using the chassis ID number (0-99). A range of chassis, using two chassis ID numbers in brackets, e.g., [2-87]. All chassis in the ICIM2 domain, using the wildcard character (*) in place of a chassis ID. Parameters The chassisidvalue parameter can be any number from 0 to 99, a bracketed pair of numbers in the same range separated by a hyphen (-), or a wildcard (*) to indicate all chassis.
Chapter 4 Module Mode Commands populated. For example, the chassis range [1-7] is valid even if there are fewer than seven chassis within that range. In addition, all chassis within the specified range are included whether or not their chassis numbers are contiguous. For an element management system or other automatic control interface, a specific chassis and slot are required for backward compatibility, and should always be specified.
exit exit Syntax exit Description The exit command is used to exit Module command mode to the CLI command mode for the purpose of entering CLI mode commands or selecting ICIM or Terminal command mode. Note: The exit command is not recognized in CLI mode and does not result in a logout. See logout (on page 60) for details.
Chapter 4 Module Mode Commands help Syntax help modeOption Description The help command is used alone to display onscreen help for all Module mode commands, or with a modeOption parameter to display help for a single command or function. Note: Typing a question mark (?) at the command prompt gives the same result as typing help without a mode option parameter. Parameters The possible values for the modeOption parameter and their results are listed below.
help module alarm chassis info logout manual modid reset set show slot - Enter module mode - Display active alarms - Set the chassis (and optionally the slot) specification for module commands - Display detailed information regarding modules - Log off this system - Show detailed help text - Set the chassis and slot ranges for module commands - Reset a module to its default values - Set a value for a module - Display the values of specified parameters.
Chapter 4 Module Mode Commands info alarm Syntax info alarm alarmName detail1 detail2 . . . detailn Description The info alarm command is used to display more detailed alarm information than is returned by using the show command. Parameters The alarmName parameter specifies the type of alarm. The allowable alarmName values vary by module because different modules have different types of alarms.
info alarm Detail parameter Description Type Alarm type (types 1, 2, and 7 are adjustable). Value Alarm state. Access Rights Required Read, ReadWrite, or Admin Example The following sample dialog illustrates the use of the info alarm command to view the thresholds of a post-amplifier output power alarm. Note that these thresholds are relative to the nominal alarm value.
Chapter 4 Module Mode Commands info control Syntax info control controlName detail1 detail2 . . . detailn Description The info control command is used to display more detailed control information than is returned by using the show command. Parameters The controlName parameter specifies the type of control. Different application modules have different types of controls, so the allowable controlName values vary by module type.
info control 20/08 MODULE> info control mode value statenames MODID 20/08 NAME Mode VALUE Auto (2) STATENAMES Cross (0), Bar (1), Auto (2) SUCCESS! 20/08 MODULE> In the example above, the control's name pattern was explicit (no wildcards). The details to be listed were Value and the available StateNames (not all controls and monitors have StateNames). In this case, the value is Auto (2).
Chapter 4 Module Mode Commands info module Syntax info module detail1 detail2 . . . detailn Description The info module command is used to display more detailed module information than is returned by using the show command. Parameters The detail parameter specifies the characteristics that can be requested for each module in the command scope, and are as follows: 56 Detail parameter Description Activerev Active software image revision for the module.
info module Detail parameter Description Selftest Status of module self test. Serial Serial number. Tos Time of service. Access Rights Required Read, ReadWrite, or Admin Example The example below shows how a network management system might construct an info module command to determine the domain of an ICIM2.
Chapter 4 Module Mode Commands info monitor Syntax info monitor monitorname detail1 detail2 . . . detailn Description The info monitor command is used to display more detailed monitor information than is returned by using the show command. Parameters The monitorname parameter specifies the type of monitored information. Because different applications modules have different types of monitored parameters, the allowable monitorname values vary by module type.
info monitor SUCCESS! 01/05 MODULE> In the example above, the monitor's name pattern was explicit (no wildcards). The details to be listed were all possible monitor details for a Transmitter Input RF monitor name.
Chapter 4 Module Mode Commands logout Syntax logout Description The logout command is used to terminate the current CLI session. This command is available in every command mode. Important: For Telnet operation, the computer you are using must have a network connection through which it can reach the ICIM2 using its IP address. No more than four Telnet sessions are allowed at one time. If IPsec is enabled on the ICIM2, it must also be enabled on the remote CLI user's computer.
manual manual Syntax manual Description The manual command is used to display detailed help for Module command mode, or for another command mode if specified while another mode is active. Parameters None Access Rights Required Read, ReadWrite, or Admin Example 20/08 MODULE> manual Try one of these help commands for details on specific modes: module manual terminal manual icim manual General Hints: Keywords can be abbreviated to a unique prefix.
Chapter 4 Module Mode Commands Use Exit to leave Module mode, or Logout to exit the CLI interface All keywords and parameters are caseless. That is, MoDuLe == MODULE == module Module Commands: alarm [parameters] Use the 'alarm' command to show all the current alarms. This command works in all modes. Using the optional parameter 'domain' is the same as not using any parameter. However, using the optional parameter 'module' will display only the alarms for the currently selected module.
manual X/Y MODULE> info monitor where is the actual monitor name such as Enable. Wildcards are allowed. For example, LasTemp* will select LasTempA and LasTempB.
Chapter 4 Module Mode Commands X/Y MODULE> set alarmparam where is the name of the alarm and is one of the following values: hysteresis - The alarm threshold hysteresis value majorhigh - The high critical alarm threshold value; must be less than or equal to the upper limit for this alarm majorlow - The low critical alarm threshold value; must be greater than or equal to the lower limit for this alarm minorhigh - The high non-critical alarm threshold value mi
modid modid Syntax modid modIdValue Description The modid command is used to specify a chassis and slot location using a single modidValue parameter. Parameters The modidValue parameter can take any of these forms: A 4-digit number signifying a single chassis and slot location, such as 0512 for chassis 5, slot 12. Bracketed numbers separated by a / symbol, representing a range of chassis and slot locations, such as [1-5]/[4-13] for chassis 1 through 5, slots 4 through 13.
Chapter 4 Module Mode Commands However, modspecs do not affect the scope of CLI, ICIM, or Terminal mode commands. When specifying a range of chassis or slots, the specified range need not be fully populated. For example, the chassis range [1-7] is valid even if there are fewer than seven chassis within that range. In addition, all chassis within the specified range are included whether or not their chassis numbers are contiguous.
reset reset Syntax reset Description The reset command is used to set all controls and alarms in a specified module to their factory defaults. Because this action has potentially severe consequences, this command can only be executed by an Admin user as explained in User Authorization (on page 9), and then only for a specific chassis and module. It is not possible to reset a range of modules, a chassis, or a range of chassis using a single reset command.
Chapter 4 Module Mode Commands set alarmparam 68 4025561 Rev A
set alarmparam set alarmparam Syntax set alarmparam alarmName alarmParamName alarmParamValue Description The set alarmparam command can be used to change the values of certain types of alarm parameters. The set alarmparam command is typically used in conjunction with the info command to first learn about alarm type and status, and then change the alarm status where appropriate and allowed. Alarm Types Alarms are classified by type to characterize their overall behavior.
Chapter 4 Module Mode Commands Non-Boolean alarms also have a hysteresis setting that can be used to adjust the amount of change required to switch states. For possible hysteresis values, see Module Parameter Descriptions (on page 245). For additional information, see the SNMP Management section of the Prisma II Enhanced Management System Guide, System Release 2.04, part number 4025559.
set alarmparam alarmName Description Ps3+5VDC Power supply 3 +5 V bus voltage. Ps3-5VDC Power supply 3 -5 V bus voltage. Transmitter (devtype: 1033) alarmName Description LasBias Transmitter laser bias current. LasTemp Transmitter laser temperature. ModTemp Transmitter module temperature. Psbs2G Transmitter 2 GHz SBS power level. PLLOCK Transmitter phase locked loop status. CPLock Transmitter constant power lock status. InRF Transmitter relative RF input power.
Chapter 4 Module Mode Commands alarmName Description IntPs Post-amplifier internal power supplies. Enable Post-amplifier output enable. LasTempA Post-amplifier laser temperature, top half. LasTempB Post-amplifier laser temperature, bottom half. LasBiasA Post-amplifier laser bias, top half. LasBiasB Post-amplifier laser bias, bottom half. InPwr Post-amplifier optical input power. ServiceA Post-amplifier Service Mode, top half. ServiceB Post-amplifier Service Mode, bottom half.
set alarmparam This response shows that the OutPwr, LasTemp, LasBias, and InPwr alarms all have majorlow and majorhigh parameters. However, only InPwr, OutPwr, and LasBias can be changed, as LasTemp is of type 3 rather than 1, 2, or 7. The following sample dialog shows how a craft operator would set the majorhigh parameter of outpwr to 35, and then confirm the change.
Chapter 4 Module Mode Commands set control Syntax set control controlName controlValue Description The set control command is followed by two additional arguments: controlName identifies the control parameter, and controlValue specifies the value to be assigned. Important: To avoid possible system disruption, broadcast set commands are not supported. This means that the set control command can only be applied to one module (chassis and slot number) at a time.
set control Control Description Type Possible Values LenMode Fine tunes for length. S On (1) for Super Trunk links, Off (0) for Edge Modulation links OMISet Sets the OMI level; only when AGC ON. F -6.0 dB to +1.0 dB in 0.5 dB steps CWMode CWMode ON reduces InRF monitor value by 2 dB to indicate actual modulation level. S On (1), Off (0) Mute Enables (On) or disables (Off) alarm-based muting.
Chapter 4 Module Mode Commands Optical Switch (devtype: 4011) Control Description Type Mode Selects automatic or manual switch S control. Auto (2), Bar (1), Cross (0) Wavelen Wavelength for both inputs. S 1550nm (1), 1310nm (0) NomPin3 Nominal input power at Port 3. F -8 dBm to +23 dBm in 0.1 dB steps NomPin4 Nominal input power at Port 4. F -8 dBm to +23 dBm in 0.1 dB steps Delta F Value in dB relative to nominal below which the input must fall to switch. 1 to 10 in 0.
set control This example shows what would happen if the operator had not specified the chassis number in advance: */05 MODULE> set control enable 0 Error: This command can only be used at an explicit chassis and slot prompt Set the chassis and slot to specific values before using this command */05 MODULE> Related Commands show control 4025561 Rev A 77
Chapter 4 Module Mode Commands set module Syntax set module CLLI clliString Description The set module command is used to define a Common Language Location Identifier (CLLI) code for a specified module. This helps ensure compatibility with telecommunications element management systems that use CLLI codes to identify and geographically locate devices. Once defined, the set module command can be used to refresh or modify the CLLI code for each module as needed.
set module The next example shows how an element management system might include space characters in the CLLI code shown above: */* MODULE> chassis 10 slot 5 10/05 MODULE> set module CLLI "DNVR CO 56OSW" SUCCESS! MODULE> info module clli MODID 02/11 CLLI DNVR CO 560SW SUCCESS! 02/11 MODULE> Related Commands info module 4025561 Rev A 79
Chapter 4 Module Mode Commands show alarmparam Syntax show alarmparam alarmName alarmParamName Description The show alarmparam command is used to select a particular alarm (alarmName) and display the value of a specified parameter for that alarm (alarmParamName). Alarm parameters are settings that control when an alarm occurs, its severity, and the size of the steps used to adjust alarm threshold settings.
show alarmparam Power Supply, Slot 1 (devtype: 5013) alarmName Description Ps1PwrIn Power supply 1 input power status. Ps1+24 Power supply 1 +24 V bus voltage. Ps1+5VDC Power supply 1 +5 V bus voltage. Ps1-5VDC Power supply 1 -5 V bus voltage. Power Supply, Slot 3 (devtype: 5013) alarmName Description Ps3PwrIn Power supply 3 input power status. Ps3+24 Power supply 3 +24 V bus voltage. Ps3+5VDC Power supply 3 +5 V bus voltage. Ps3-5VDC Power supply 3 -5 V bus voltage.
Chapter 4 Module Mode Commands alarmName Description LasTemp Pre-amplifier laser temperature. LasBias Pre-amplifier laser bias current. InPwr Pre-amplifier input optical power. Service Pre-amplifier Service mode. Post-Amplifier (devtype: 3031) alarmName Description PsOk Post-amplifier power supply input voltages. OutPwrA Post-amplifier optical output power, top half. OutPwrB Post-amplifier optical output power, bottom half. IntPs Post-amplifier internal power supplies.
show alarmparam Example The following example shows the kind of information returned by this command. */* MODULE> show alarmparam *pwr minorhigh MODID 20/05 20/06 20/06 NAME OutPwr InPwr MaxInPwr MINORHIGH 1 5 N/A SUCCESS! */* MODULE> Note: The returned value of N/A shown above indicates that the alarm does not have the requested parameter. Some alarm values can also be changed by a properly authorized craft operator or element management system. See set alarmparam (on page 69) for details.
Chapter 4 Module Mode Commands show alarmstate Syntax show alarmstate alarmName Description The show alarmstate command is used to display the specified states of specified active alarms. The alarmName parameter identifies the alarm or alarms to be displayed. Parameters The values possible for the alarmName parameters depends on the application module in question. The following tables identify the alarms for each application module along with their alarm types and possible alarm state values.
show alarmstate alarmName Description Ps3+24 Power supply 3 +24 V bus voltage. Ps3+5VDC Power supply 3 +5 V bus voltage. Ps3-5VDC Power supply 3 -5 V bus voltage. Transmitter (devtype: 1033) alarmName Description LasBias Transmitter laser bias current. LasTemp Transmitter laser temperature. ModTemp Transmitter module temperature. Psbs2G Transmitter 2 GHz SBS power level. PLLOCK Transmitter phase locked loop status. CPLock Transmitter constant power lock status.
Chapter 4 Module Mode Commands alarmName Description OutPwrB Post-amplifier optical output power, bottom half. IntPs Post-amplifier internal power supplies. Enable Post-amplifier output enable. LasTempA Post-amplifier laser temperature, top half. LasTempB Post-amplifier laser temperature, bottom half. LasBiasA Post-amplifier laser bias, top half. LasBiasB Post-amplifier laser bias, bottom half. InPwr Post-amplifier optical input power. ServiceA Post-amplifier Service Mode, top half.
show alarmstate Note: The information returned by the show alarmstate command includes both the state value and how to interpret it.
Chapter 4 Module Mode Commands show control Syntax show control controlName Description The show control command is used to display the values of all control parameters in the range indicated by controlName. Control Types Control parameters are classified as type F (floating-point) or type S (state) to characterize the types of variables they control. In general: Type F controls are numeric values that can vary between maximum and minimum thresholds.
show control Control Description Type Possible Values Mute Enables (On) or disables (Off) alarm-based muting. S On (1), Off (0) Pre-Amplifier (devtype: 3030) Control Description Type Possible Values Enable Enables or disables the laser. S On (1), Off (0) SetAtten Attenuates optical output power. F 0 to 3 dB in 1.0 dB steps Master When set to Master, pre-amp is controlled by Enable; if Slave, preamp is controlled by Enable and CNT_IN_1.
Chapter 4 Module Mode Commands Delta F Value in dB relative to nominal below which the input must fall to switch. 1 to 10 in 0.1 steps HystAmpl Value above which the input must F rise to start the hysteresis timer to restore the original switch position (revert in auto). 0.5 to 9.5 in 0.1 steps HystTime Length of time primary power is above the restore threshold before switch to primary (revert in auto). Revert Allows switch to revert to primary S after power is restored.
show module show module Syntax show module Description The show module command is used to generate a list of information for specific modules to help with their physical identification. Modules are specified by first changing to the desired Module prompt (modspec), and then entering the show module command. Parameters None; however, the modspec is used to specify the scope of the command within the ICIM2 domain. See About Modspecs (on page 41) for further information.
Chapter 4 Module Mode Commands show monitor Syntax show monitor monitorName Description The show monitor command is used to display the values of all active alarms in the range indicated by monitorName. Monitored Parameter Types Monitored parameters are classified as type F (floating-point) or type S (state) to characterize the types of variables they monitor. In general: Type F parameters monitor numeric values that can vary between maximum and minimum thresholds.
show monitor Parameter Description Type Possible Values Ps3Inst Power supply 3 input power status. S Yes (1), No (0) Type Possible Values Power Supply Slot 1 (devtype: 5013) Parameter Description Ps1+24V Power supply 1 +24 V bus voltage. F Analog Value Ps1+5V Power supply 1 +5 V bus voltage. F Analog Value Ps1-5V Power supply 1 -5V bus voltage. F Analog Value Ps1Temp Power supply 1 internal temperature.
Chapter 4 Module Mode Commands Pre-Amplifier (devtype: 3030) Parameter Description Type Possible Values InPwr Pre-amp optical input power. F Analog value OutPwr Pre-amp optical output power. F Analog value LasTemp Pre-amp laser temperature. F Analog value LasBias Pre-amp laser bias current. F Analog value LasLim Pre-amp laser operating current limit. F Analog value TecCur Thermoelectric cooler current. F Analog value ModTemp Module temperature.
show monitor Parameter Description Type Possible Values PwrIn4 Optical switch input power, Port 4. F Analog Value ModTemp Optical switch module temperature. F Analog Value SwTemp Optical switch switch temperature. F Analog Value Access Rights Required Read, ReadWrite, or Admin Example The following sample dialog shows how the kind of information returned by this command. */* MODULE> show monitor *pwr MODID 20/05 20/06 20/06 20/13 20/13 NAME OutPwr InPwr OutPwr InPwr OutPwr VALUE 8.29224 5.
Chapter 4 Module Mode Commands slot Syntax slot slotidValue Description The slot command is used to specify: A single slot, using the desired slot number (0-47). A range of slots, using two slot numbers in brackets, e.g., [2-18]. All slots in all chassis currently specified, using the wildcard character (*) in place of a slot number. Parameters The slotidValue parameter can be any number from 0 to 47, or a bracketed pair of numbers in this range separated by a hyphen (-).
slot commands. When specifying a range of chassis or slots, the specified range need not be fully populated. For example, the chassis range [1-7] is valid even if there are fewer than seven chassis within that range. In addition, all chassis within the specified range are included whether or not their chassis numbers are contiguous. For an element management system or other automatic control interface, a specific chassis and slot are required for backward compatibility, and should always be specified.
5 Chapter 5 ICIM Mode Commands Introduction This chapter describes the commands that can be executed in the ICIM command mode. These commands enable monitoring and control of the ICIM2 module itself as well as general parameters of the ICIM2 domain.
Chapter 5 ICIM Mode Commands In This Chapter 100 Overview.............................................................................................. 101 alarm ..................................................................................................... 103 eventlogclear........................................................................................ 104 eventlogfilter...................................................
Overview Overview ICIM mode commands provide for monitoring and control of the ICIM2 itself and for the ICIM2 domain in general. Types of ICIM Commands The following commands are recognized in ICIM command mode: The alarm command is used to display all active alarms in the ICIM2 domain. The eventlogclear command is used to clear the ICIM2 event log. The eventlogfilter command is used to change the event log filter settings. The exit command is used to exit ICIM command mode and return to CLI command mode.
Chapter 5 ICIM Mode Commands The user commands are used to add, change, and delete system user information and to unlock user accounts. This chapter describes these commands and their applications in detail. To Access ICIM Command Mode The CLI only recognizes ICIM mode commands in ICIM command mode. Complete the following steps to enter ICIM command mode. 102 1 Confirm that you have logged onto CLI as explained in CLI Login and Logout (on page 10).
alarm alarm Syntax alarm Description The alarm command is used to display all active alarms in the domain of the ICIM2. This command produces the same results whether entered in CLI, Module, Terminal, or ICIM command mode. Note: This command is functionally equivalent to alarm domain (on page 45). Parameters None Access Rights Required Read, ReadWrite, or Admin Example ICIM> alarm No active alarms found SUCCESS! ICIM> This response shows that no alarms are active in the ICIM2 domain.
Chapter 5 ICIM Mode Commands eventlogclear Syntax eventlogclear Description The eventlogclear command is used to erase the entire contents of the event log. The user is prompted for confirmation before action is taken. It is recommended that the event log be cleared after it has been copied (transferred) to a remote FTP server. See file (on page 108) for details. Note: This command performs the same function as the Clear Event Log button in the Event Log screen of the ICIM Web Interface.
eventlogfilter eventlogfilter Syntax eventlogfilter logCategory setting Description The eventlogfilter command is used to set the event log filter parameters, which select the categories of events that are saved in the ICIM2 event log. Parameters The logCategory parameter selects the event category to be changed. It can have one of the following values. logCategory Description hardware Designates hardware events, i.e., module insertion and removal events.
Chapter 5 ICIM Mode Commands show eventlogfilter 106 4025561 Rev A
exit exit Syntax exit Description The exit command is used to exit ICIM command mode to the CLI command mode for the purpose of entering CLI mode commands or selecting Module or Terminal command mode. Note: The exit command is not recognized in CLI mode and does not result in a logout. See logout (on page 120) for details.
Chapter 5 ICIM Mode Commands file Syntax file fileParameter value Description The file command is used to set the file management parameters used for FTP transfers of the event log file from the ICIM2 to a remote FTP server. Note: This command is functionally equivalent to the subset of ICIM MIB objects used for file management, as further explained in the SNMP Management section of the Prisma II Enhanced Management System Guide, System Release 2.04, part number 4025559.
file Access Rights Required ReadWrite or Admin Examples ICIM> file ip 192.28.46.118 SUCCESS! ICIM> file name eventlog.
Chapter 5 ICIM Mode Commands help Syntax help modeOption Description The help command is used alone to display onscreen help for all ICIM mode commands, or with a modeOption parameter to display help for a single command or function. Note: Typing a question mark (?) character at the ICIM> command prompt gives the same result as typing help without a mode option parameter. Parameters The possible values for the modeOption parameter and their results are listed below.
help icim alarm eventlogclear eventlogfilter file ike - info - iproute ipsec logout manual reboot set show - sntp traps user - Enter ICIM mode Display active alarms for all modules Clear the event log Set the event log filter parameters Access file related commands Access IPsec Internet key exchange protocol related commands Display information on 1 or more ICIM2 parameters. All parameters are optional and can be entered in any order.
Chapter 5 ICIM Mode Commands ike Syntax ike ikeAction IpAddress Description The ike command is used to change the internet key exchange (IKE) settings. Note: IPsec peers cannot be added or deleted through Telnet unless IPsec is enabled. Parameters The value of the ikeAction parameter can be either add to add an IPsec peer, or delete to delete an IPsec peer. In either case, the parameter is followed by the IpAddress of the peer. The IP address must be of the form 172.24.28.151.
info info Syntax info icimValue1 icimValue2 . . . icimValuen Description The info command is used to request a listing of one or more parameter values specific to the ICIM2 module itself. Any number of these values can be listed, and the output returns the values in the order requested. Parameters Each icimValue parameter can have one of the values listed below. 4025561 Rev A Argument Description ACTIVEREV Active software image revision for the ICIM2.
Chapter 5 ICIM Mode Commands Argument Description FTPSERVER IP address of FTP Server (used by SOUP). FTPUSER User name for FTP account. GATEWAY IP address of TCP/IP gateway, for packet routing. HWREV Hardware Revision. INACTIVEREV Inactive software image revision for the ICIM2. IP IP address for the ICIM2. IPSEC State of IPSecurity enable. LOCKOUT Current User Lockout interval. MAC MAC Address for the ICIM2. MANDATA Manufacturing data for the ICIM2.
info Example The sample dialog below shows how this command might be sent by an element management system. CLI> icim info IP devtype serial swrev attnstatus size exit IP DEVTYPE 172.23.200.154 5011 SERIAL AADORTI SWREV 0.00.
Chapter 5 ICIM Mode Commands iproute Syntax iproute keyWord ip_address gateWay Description The iproute command is used to add, delete, or show ICIM2 IP route definitions. Parameters Each keyWord parameter can have one of the values listed below. keyWord Description add Adds a new route to the specified destination IP address via the specified gateway IP address. delete Deletes the existing route to the specified destination IP address via the specified gateway IP address.
iproute Related Commands show iproute 4025561 Rev A 117
Chapter 5 ICIM Mode Commands ipsec Syntax ipsec ipsecValue Description The ipsec command is used to enable or disable the use of IP Security (IPsec). Note: This command is not available through Telnet. Parameters Each ipsecValue parameter can have one of the values listed below. Argument Description enable Enable IPsec. disable Disable IPsec. Access Rights Required Admin Example The sample dialog below shows how this command might be used to disable and then re-enable IPsec.
ipsec IPsec is about to be enabled or disabled. This requires enabling or disabling IPsec on all peers. Failure to do so will result in a loss of communications on some or all interfaces including [but not limited to] SNMP, telnet, web and all other IP based interfaces. If configured incorrectly, the only means of communication will be through the local craft interface. IPsec is about to be enabled/disabled. Are you sure you want to proceed (Yes/No)? yes IPsec enabled for 172.24.28.
Chapter 5 ICIM Mode Commands logout Syntax logout Description The logout command is used to terminate the current CLI session. This command is available in every command mode. Important: For Telnet operation, the computer you are using must have a network connection through which it can reach the ICIM2 using its IP address. No more than four Telnet sessions are allowed at one time. If IPsec is enabled on the ICIM2, it must also be enabled on the remote CLI user's computer.
manual manual Syntax manual Description The manual command is used to display detailed help for the ICIM command mode, or for another command mode if specified while another mode is active. Parameters None Access Rights Required Read, ReadWrite, or Admin Example ICIM> manual Try one of these help commands for details on specific modes: module manual terminal manual icim manual General Hints: Keywords can be abbreviated to a unique prefix.
Chapter 5 ICIM Mode Commands eventlogclear Use the 'eventlogclear' command to erase the entire contents of the event log. eventlogfilter Use the 'eventlogfilter' command to set the filter parameters for the event log. There are three available parameters: hardware, provisioning and system. Specify on to log events of each parameter type or off to skip logging these events.
manual info Use the 'info' command to display one or more ICIM parameter values. Any number of available parameters can be requested with the same command.
Chapter 5 ICIM Mode Commands set Use the 'set' command to set any of the user-changeable ICIM2 values.
manual user Use the 'user' command to display or modify the user table. To show the table: ICIM> show user To add a new user to the table: ICIM> user add The user_id field must be between 6 and 14 characters and contain both alpha and numeric characters. The access_level can be admin, read or readwrite. The account_status can be either enable or disable. Once the command is accepted, the user will be prompted for a new password.
Chapter 5 ICIM Mode Commands reboot Syntax reboot Description The reboot command causes the ICIM2 to be reset. Note: This command resets the ICIM2 only. To reset other modules, see reset (on page 67). Parameters None Access Rights Required Admin Example The lines shown below will be followed by the usual startup messages, and then by the login prompt. ICIM> reboot The ICIM2 is about to reboot. This will end all current login and web sessions.
set set Syntax set valueName newValue Description The set command allows a single parameter value to be set in the ICIM2 by specifying the parameter to be changed and the new value. Parameters The valueName parameter can be one of the following: valueName Description CLLI Common Language Locator ID code for the ICIM2 (up to 20 characters, no spaces). CLOCK Date and Time as maintained by the ICIM2. COMMREAD SNMP Read Community string (default prismaread).
Chapter 5 ICIM Mode Commands ICIM2 NVRAM, but do not take effect until the next reboot. Use the set tzone command carefully. Systems that use an external clock reference may periodically overwrite settings made with this command. Date, time, and timezone changes should be made to the master clock reference if one is in use. Access Rights Required Admin Example ICIM> set ip 192.0.2.12 ICIM> set gateway 192.0.2.17 ICIM> set subnet 192.0.2.
set clock set clock Syntax set clock "mm/dd/yyyy hh:mm:ss" Description The set clock command lets you set and confirm the ICIM2 real time clock (RTC) using a single command. Note: You must enclose the new date/time value in quotes. Use this command carefully. Systems that use an external clock reference may periodically overwrite settings made with this command. Make date, time, and timezone changes to the master clock reference, if one is used.
Chapter 5 ICIM Mode Commands SUCCESS! ICIM> Related Commands show clock 130 4025561 Rev A
show show Syntax show icimValue1 icimValue2 . . . icimValuen Description The show command is used to request a listing of one or more parameter values specific to the ICIM2 module itself. Multiple values may be listed, except that values returning multiple-word responses (see table below) must be listed individually. When two or more values are listed, the output returns the values in the order requested. Parameters Each icimValue parameter can have one of the values listed below.
Chapter 5 ICIM Mode Commands Argument Description DOWNLDSEM Application security semaphore (used by SOUP). DOWNLDSIG Application security information (used by SOUP). DOWNLDSTATE State machine value to indicate download progress (used by SOUP). DOWNLDTGT Module to upgrade with release image (used by SOUP). DOWNLDUSER Application User ID to ensure only one instance (used by SOUP).
show Argument Description SMC The value (Chassis * 100) + Slot for the ICIM2. SNTP 1 Parameters to synchronize the ICIM2 real time clock to an NTP server STATUSMSG Status and Error message information. SUBNET Subnet mask, such as 255.255.255.0. SWDATE Software date (obsolete). SWREV Software revision (obsolete). THRESHOLD User failed login threshold. TIMEOUT User inactivity timeout. TOS Time of Service of the ICIM2. TRAPS 1 Displays the current trap receiver table.
Chapter 5 ICIM Mode Commands show clock Syntax show clock Description The show clock command is used to display the current ICIM2 Real Time Clock (RTC) date and time settings.
show domain show domain Syntax show domain Description The show domain command is used to request information about the elements in the ICIM2 domain. This command displays a list of all of the modules in the ICIM2 domain. Parameters None Access Rights Required Read, ReadWrite, or Admin Example The sample dialog below illustrates the use of this command. ICIM> show domain MODID 20/00 20/03 20/05 20/07 20/08 DEVTYPE 5012 5013 1031 3030 3031 SERIAL ~AAOZZGM N/A 12345678 AACZOIF !AAGJUHB ACTIVEREV 1.01.
Chapter 5 ICIM Mode Commands show eventlog Syntax show eventlog Description The show eventlog command is used to display an abbreviated version of the event log. Only three columns are displayed: date/time, user, and description. This is the preferred method for viewing the event log through the CLI. For further information, see the Event Log section of the Prisma II Enhanced Management System Guide, System Release 2.04, part number 4025559.
show eventlogall show eventlogall Syntax show eventlogall Description The show eventlogall command is used to display a full version of the event log. All columns are displayed: date/time, user, user access level, log category, log action ID, and description. This method typically produces an output too wide for terminal settings, but may be useful when all log fields are needed. For further information, see the Event Log section of the Prisma II Enhanced Management System Guide, System Release 2.
Chapter 5 ICIM Mode Commands show eventlogfilter Syntax show eventlogfilter Description The show eventlogfilter command is used to display the current event log filter parameter settings. These settings determine which of three categories of events (Provisioning, Hardware, and System) are included or excluded in future event log entries. For further information, see the Event Log section of the Prisma II Enhanced Management System Guide, System Release 2.04, part number 4025559.
show file show file Syntax show file Description The show file command is used to display the current event log file management parameter settings. These settings control the FTP transfer of the event log file from the ICIM2 to a remote FTP server. Parameters None Access Rights Required ReadWrite or Admin Example The sample dialog below illustrates the use of this command. ICIM> show file File Transfer Settings: IP Address 192.15.26.102 Remote Path \ftproot File Name eventlog.
Chapter 5 ICIM Mode Commands show ike Syntax show ike Description The show ike command is used to display the current IPsec Internet Key Exchange (IKE) parameter settings. These settings include the IP peers for the ICIM2, but the preshared keys are not displayed. Parameters None Access Rights Required Admin Example The sample dialog below illustrates the use of this command. ICIM> show ike IPSec is not enabled. IKE Peer -------192.18.65.
show iproute show iproute Syntax show iproute Description The show iproute command is used to display the ICIM2 IP routing table. Parameters None Access Rights Required Read, ReadWrite, or Admin Example The sample dialog below illustrates the use of this command. ICIM> show iproute ROUTE NET TABLE destination gateway flags Refcnt Use Interface -----------------------------------------------------------------------------0.0.0.0 192.24.28.254 33619971 2 127 motfec0 192.24.28.0 192.24.28.
Chapter 5 ICIM Mode Commands show provisioning Syntax show provisioning Description The show provisioning command is used to request information about how the elements of the ICIM2 domain are currently provisioned (configured). This command displays a list of the CLI commands needed to restore any replacement modules in the ICIM2 domain to their current operating states. This list can serve as a command reference to quickly configure a replacement module so that it operates identically to the original.
show provisioning Using the list requires first locating all command lines that target the chassis and slot location of the replacement module. The commands are then sent to the replacement module one at a time in the order listed. For example, after replacing the module in chassis 20 slot 6 in the above example, the commands on lines 6-9 of the response would be sent to configure the replacement module.
Chapter 5 ICIM Mode Commands show sntp Syntax show sntp Description The show sntp command is used to display the current settings for parameters that synchronize the ICIM2 real time clock (RTC) to a Network Time Protocol (NTP) server. For further information, see sntp and the SNTP Time Synchronization section of the Prisma II Enhanced Management System Guide, System Release 2.04, part number 4025559.
show traps show traps Syntax show traps Description The show traps command is used to request information about the traps defined in the ICIM2 Traps table. In response to this command, the system displays the current status of the Trap table.
Chapter 5 ICIM Mode Commands show user Syntax show user Description The show user command is used by an Administrator (a user with Admin level authorization) to list all the available logins and authorization levels. It does not display the passwords.
sntp sntp Syntax sntp valueName newValue Description The sntp command is used to set the individual parameters that control SNTP time synchronization by specifying the parameter to be changed and the new value. Parameters The valueName parameter can be one of the following: valueName Description INTERVAL Interval in hours (1-168) between consecutive ICIM2 time requests to the NTP server. IP IP address of the NTP server in xxx.xxx.xxx.xxx format.
Chapter 5 ICIM Mode Commands Access Rights Required Admin Example ICIM> sntp state disabled SUCCESS! ICIM> sntp mode unicast SUCCESS! ICIM> sntp timeout 5 SUCCESS! ICIM> sntp interval 1 SUCCESS! ICIM> sntp ip 123.2.23.
traps traps Syntax traps state index [IPAddress] Description The traps command allows the entries in the Trap table to be enabled or disabled, and allows the IP address of the Trap table to be set. Note: The Trap table has 10 entries, indexed 0 through 9. Each entry can be enabled by supplying a valid IP address, or if the table entry already has a valid IP address. When enabling or disabling an entry already in the Traps table, the IP address parameter is optional, so you do not have to specify it.
Chapter 5 ICIM Mode Commands user add Syntax user add username authlevel accountstatus Description The user add command is used to add a new login and password to the ICIM2 authentication table. A dialog is used to obtain and validate the password. Parameters The username, or user identifier, must be 6 to 14 characters in length and contain both letters and numbers. The username cannot include special characters. An example of a valid username is abc123.
user add Example ICIM> user add smith8 readwrite enable Please enter the password: Related Commands user change user delete user unlock show user 4025561 Rev A 151
Chapter 5 ICIM Mode Commands user change Syntax user change userparam username newvalue Description The user change command is used by the Administrator (a user with Admin authorization) to change the access rights, account status, or password of an existing user. A dialog is used to obtain and validate the new setting. Passwords must be 6 to 14 characters in length and contain both letters and numbers. Passwords may contain special characters.
user change Related Commands user add user delete user unlock show user 4025561 Rev A 153
Chapter 5 ICIM Mode Commands user delete Syntax user delete username Description The user delete command is used by an Administrator (a user with Admin level authorization) to remove an existing login and password from the ICIM2 authentication table. Note: It is not necessary to delete a user to change account settings. See user change (on page 152) for details. Deleting a user that is already logged in does not terminate their current session.
user unlock user unlock Syntax user unlock username Description The user unlock command is used by an Administrator (a user with Admin level authorization) to unlock a locked-out user before the lockout interval has expired. Note: It is not necessary to unlock a user to change account settings. See user change (on page 152) for details. Unlocking a locked-out user also resets the failed login attempts counter for that user.
Chapter 5 ICIM Mode Commands show user 156 4025561 Rev A
6 Chapter 6 Terminal Mode Commands Introduction This chapter describes the commands that can be executed in the Terminal command mode. These commands control the appearance of information displayed onscreen in response to other CLI commands. In This Chapter 4025561 Rev A Overview.............................................................................................. 158 alarm .....................................................................................................
Chapter 6 Terminal Mode Commands Overview Terminal mode commands are used to control the way that information is displayed onscreen in response to CLI commands. Types of Terminal Commands The following commands are recognized in Terminal command mode: The colsep command controls the separation between columns in a tabular information display. The exit command is used to exit Terminal command mode and return to CLI command mode.
alarm alarm Syntax alarm Description The alarm command is used to display all active alarms in the domain of the ICIM2. This command produces the same results whether entered in CLI, Module, Terminal, or ICIM command mode. Note: This command is functionally equivalent to alarm domain (on page 45). Parameters None Access Rights Required Read, ReadWrite, or Admin Example TERMINAL> alarm No active alarms found SUCCESS! TERMINAL> This response shows that no alarms are active in the ICIM2 domain.
Chapter 6 Terminal Mode Commands colsep Syntax colsep "string" Description The colsep command controls the separation between columns of output in the display. By default, output is displayed in columns only slightly wider than are needed for the longest value in the column. Adding spaces between columns can make the output more legible to a craft operator, but may make output parsing more difficult for a remote element management system.
colsep The next example shows how the output could be modified to make it more easily parsed by a program such as Microsoft Excel, which recognizes a comma-separated values (CSV) file format.
Chapter 6 Terminal Mode Commands exit Syntax exit Description The exit command is used to exit Terminal command mode to the CLI command mode for the purpose of entering CLI mode commands or selecting Module or ICIM command mode. Note: The exit command is not recognized in CLI mode and does not result in a logout. See logout (on page 167) for details.
headers headers Syntax headers digits Description The headers command is used to enable or disable the display of column headers that may appear in CLI output. Column headers are enabled by default, but may be disabled and re-enabled using the headers command. Note: This command does not affect the event log, which is always displayed without headers. Parameters The digits parameter is 0 to disable header display, and 1 to enable header display.
Chapter 6 Terminal Mode Commands 20/03 MODULE> show monitor ps*5* 20/03 20/03 20/03 20/03 Ps1+5V Ps1-5V Ps3+5V Ps3-5V 0 0 5.39218 -5.
help help Syntax help modeOption Description The help command is used alone to display onscreen help for all Terminal mode commands, or with a modeOption parameter to display help for a single command or function. Note: Typing a question mark (?) character at the TERMINAL> command prompt gives the same result as typing help without a mode option parameter. Parameters The possible values for the modeOption parameter and their results are listed below.
Chapter 6 Terminal Mode Commands TERMINAL> Related Commands help (CLI command mode) help (Module command mode) help (ICIM command mode) 166 4025561 Rev A
logout logout Syntax logout Description The logout command is used to terminate the current CLI session. This command is available in every command mode. Important: For Telnet operation, the computer you are using must have a network connection through which it can reach the ICIM2 using its IP address. No more than four Telnet sessions are allowed at one time. If IPsec is enabled on the ICIM2, it must also be enabled on the remote CLI user's computer.
Chapter 6 Terminal Mode Commands manual Syntax manual Description The manual command is used to display onscreen instructions for Terminal command mode, or for another command mode if specified while another command mode is active. Parameters None Access Rights Required Read, ReadWrite, or Admin Example TERMINAL> manual Try one of these help commands for details on specific modes: module manual terminal manual icim manual General Hints: Keywords can be abbreviated to a unique prefix.
manual Terminal Commands: alarm Use the 'alarm' command to show all the current alarms. works in all modes. This command colsep Use the 'colsep' command to set the separation character used in the CLI output. When the display is being parsed automatically rather than by a craft operator, it may be more useful to have columns that have a fixed character as a separator.
Chapter 6 Terminal Mode Commands paging Syntax paging digits Description The paging command is used to control paging behavior for long CLI output. When paging is enabled in CLI, a feature called Smart Paging attempts to determine the best Telnet window size automatically. If it cannot do so, Smart Paging uses the number of lines specified in the Paging command as the Telnet window size. Smart Paging has no effect when paging is disabled.
paging MODID 20/05 20/05 20/05 20/05 20/05 20/06 20/06 20/06 20/06 20/07 20/07 20/07 20/07 20/07 20/08 20/08 20/08 20/08 20/08 20/08 20/08 20/08 NAME Enable CwMode LoRFInh Master RFDrive Enable Master WaveLen NomPin Enable CwMode LoRFInh Master RFDrive Cross Bar Mode WaveLen NomPIn3 NomPIn4 Delta HystAmpl SETTING 1 0 0 Slave (0) 0 1 1 1550nm (1) 0 1 1 1 Master (1) 0 False (0) False (0) Auto (1) 1550nm (1) 0 0 6 3 UNITS dB dBm dB dBm dBm dB dB Press any key to continue (Q to quit) A craft operator c
Chapter 6 Terminal Mode Commands MODID 01/05 01/05 01/05 01/05 01/05 01/05 01/05 01/07 01/07 01/07 01/07 01/07 01/08 01/08 01/08 01/08 01/08 01/09 01/09 01/09 01/09 01/09 01/12 01/12 01/12 01/12 01/12 10/09 10/09 10/09 10/09 10/09 76/06 76/06 76/06 76/06 76/06 76/06 76/06 76/06 76/06 76/06 76/06 76/06 76/08 76/08 76/08 76/08 76/08 76/10 76/10 76/10 76/10 76/10 NAME Enable AGC RFDrive OMISet Master CWMode LenMode Enable SetAtten Master LoInpEna Service Enable SetAtten Master LoInpEna Service Enable SetAtten
paging show (Terminal mode) 4025561 Rev A 173
Chapter 6 Terminal Mode Commands pattern Syntax pattern patternStyle Description The pattern command is used to select one of two pattern matching styles for the names of monitor, control, and alarm parameters. This setting controls whether CLI supports Windows style pattern matching (which includes the * wildcard character as well as ? and [xyz] patterns) or POSIX regular expression (regex) pattern matching as used in many Unix and Perl programs. The default is Windows-style or wildcard pattern matching.
pattern 20/03 MODULE> show monitor ps* MODID 20/03 20/03 20/03 20/03 20/03 20/03 20/03 20/03 20/03 20/03 NAME Ps1Inst Ps1+24V Ps1+5V Ps1-5V Ps1Temp Ps3Inst Ps3+24V Ps3+5V Ps3-5V Ps3Temp VALUE 0 0 0 0 0 1 24.4629 5.39218 -5.43724 30.4215 UNITS Inst V V V degC Inst V V V degC SUCCESS! 20/03 MODULE> show monitor ps*5* MODID 20/03 20/03 20/03 20/03 NAME Ps1+5V Ps1-5V Ps3+5V Ps3-5V VALUE 0 0 5.39218 -5.
Chapter 6 Terminal Mode Commands show Syntax show Description The show command is used to display the current values for the colsep, headers, paging, and pattern terminal states. Parameters None Access Rights Required Read, ReadWrite, or Admin Example A typical response to this command is shown in the following sample craft operator dialog.
7 Chapter 7 ICIM Web Interface Introduction This chapter describes the features and operation of the Web Interface for the ICIM2 that is supported beginning with Prisma II EMS System Release 2.0. In This Chapter 4025561 Rev A Introduction ......................................................................................... 178 Installation ........................................................................................... 180 Web Browser Setup ...........................
Chapter 7 ICIM Web Interface Introduction The ICIM Web Interface is a set of HTML pages hosted by the web server in the ICIM2. These pages display information about the ICIM2 and other modules in the ICIM2 domain. For authorized users, these pages also allow for adjustment of certain parameter values. Users navigate and interact with the ICIM Web Interface through the use of menus and hyperlinks, just as with a typical web site.
Introduction Note: For security reasons, users may not have access to every page of the ICIM Web Interface. If a particular page is unavailable to a user because of access level (Read Only, ReadWrite, or Admin), the corresponding Help section may also be unavailable.
Chapter 7 ICIM Web Interface Installation The ICIM Web Interface is already resident in the ICIM2 firmware. All that is needed for access is to install an appropriate web browser and point it to the ICIM2 IP address. Your system administrator can provide the IP address for this page in your installation. Note: System Release 2.01 and later support Mozilla for Unix or Linux, Version 1.7 and Microsoft Internet Explorer for Windows, Version 6.
Web Browser Setup Web Browser Setup Before logging in, you must set up the web browser for compatibility with the ICIM Web Interface. This involves: Enabling support for JavaScript Allowing cookies to be set Disabling auto-complete Procedures for web browser setup are provided below for each of the supported web browsers. Setup for Mozilla 1.7 Complete the following steps to set up Mozilla 1.7 for compatibility with the ICIM Web Interface.
Chapter 7 ICIM Web Interface Setup for Internet Explorer 6 Complete the following steps to set up Internet Explorer 6 for compatibility with the ICIM Web Interface. Enable JavaScript Support 1 Select Tools | Internet Options. 2 Click the Security tab. 3 Click the Custom Level button. 4 Scroll down to the Scripting section. 5 Select Enable for all three scripting categories. 6 Click OK. 7 If a message appears asking you to confirm your selections, click Yes.
Login and Logout Login and Logout To use the ICIM Web Interface, you must enter a valid User ID and Password. The default User ID and Password are given below. User ID: Administrat0r Password: AdminPassw0rd Note: The default User ID and Password each have a zero (0) in place of the expected "o" character. For security reasons, it is recommended that the default user be changed immediately. For additional information, see User Management in the Prisma II Enhanced Management System Guide, System Release 2.
Chapter 7 ICIM Web Interface 4 Press the Enter key or click the Go button. The ICIM Login page appears. 5 Type your User ID and Password in the fields provided, and then click the Login button. The ICIM Welcome page appears. 6 Use one of the following navigation methods as appropriate: 184 Click Next to go to the System View page. Or, wait 10 seconds to be taken to System View automatically.
Login and Logout Use the menu at the left of the screen to go directly to System View or to choose another page of interest. CAUTION: Always log out of the Web Interface before closing the browser. Use the Logout link at the bottom of the navigation pane on the left side of the page. Closing the browser before logging out causes the session to "hang" for the duration of a timeout interval.
Chapter 7 ICIM Web Interface 3 Locate the original default user name in the list of users. Click the Delete button beside the default user name to delete it from the list. Important: Note your new login defaults for future reference. Failure to remember your new user ID and password may result in being locked out of the ICIM2 permanently. You cannot revert to the default user name and password once they are deleted.
Using System View Using System View The System View page displays manufacturing information for the ICIM2 and selected modules. System View also allows you to view the current alarms for the ICIM2 and any application modules in the domain. To View ICIM Information The default selection, System View, displays the following information about the ICIM2: This table contains at least one, and possibly two, hyperlinks to other pages of the interface.
Chapter 7 ICIM Web Interface To View Module Summary The Module Summary table at the bottom of the System View page lists the modules in the ICIM2 domain and identifies their chassis and slot locations, module types (if reported by the module) and devtypes, and the number of alarms currently active. Note: Clicking the Details link for a particular module displays the Module Details page, described in a later section.
Using System View Note: When troubleshooting alarms, additional diagnostic information is available from the System Settings and the Event Log pages. These pages are described in later sections of this chapter.
Chapter 7 ICIM Web Interface Using ICIM Details Clicking the ICIM Details menu option displays the ICIM Details screen. This screen includes two kinds of information: A Time and Date stamp shows when the page was last updated. An ICIM Details table displays various ICIM2 parameters, and allows you to change the CLLI Code. Time and Date Stamp The Time and Date stamp shows the time that the screen on which it appears was last updated.
Using ICIM Details To Work with ICIM Details The ICIM Details table lists the ICIM2 details that are most commonly referred to for system configuration and maintenance. As suggested by the appearance of the CLLI Code field above, the CLLI code is userconfigurable. To change this parameter, click inside the CLLI Code field, type the new entry, and then click the Apply button or press Enter. To abort the entry of a parameter, click Cancel before clicking Apply.
Chapter 7 ICIM Web Interface ICIM Web Interface Field CLI Command SNMP MIB Object IP Address ICIM> info IP p2icimIPAddr IP Subnet Mask ICIM> info subnet p2icimSubnetMask IP Gateway ICIM> info gateway p2icimGatewayAddr MAC Address ICIM> info MAC p2icimMACAddr CLLI Code ICIM> info CLLI p2icimCLLICode CLEI Code ICIM> info CLEI p2icimCLEICode Manufacture Data ICIM> info mandata p2manufactureData Serial Number ICIM> info serial p2icimSerialNumber Hardware Revision ICIM> info hwrev p2
Using Module Details Using Module Details Clicking the Module Summary menu option navigates to the lower portion of the System View screen, which contains the list of modules in the ICIM2 domain. Note: In a large system, you may have to scroll the page to view all of the modules.
Chapter 7 ICIM Web Interface To View Module Details When you click Details in the Module Summary table in System View, the Module Details screen for the corresponding module appears, as shown in the example below. Note: When viewing module details, always use the links provided on the Module Details screen. Attempts to access this information by editing the URL in the browser address bar may cause unexpected results.
Using Module Details These options are described below. To View Alarms To view the status of all alarms for the chosen module, click the Alarms submenu option. The Alarm Status table appears. To View Thresholds To view the current threshold values for all alarms for the chosen module, click the Thresholds submenu option. The Module Alarm Thresholds table appears. If any of the alarms have user-adjustable threshold values, these values are shown in ruled fields to indicate that they are editable.
Chapter 7 ICIM Web Interface To change a threshold value, click inside the field, type the desired value, and then either click the Apply button to the right of the row containing the field. Or, you may press Enter to invoke the changes on that row immediately. To abort the change, click the Cancel button before clicking Apply. Clicking Cancel reloads the page, discarding any unapplied changes. Note: Clicking Apply updates all fields in the corresponding row.
Using Module Details Cancel reloads the page, discarding any unapplied changes. Note: Clicking Apply updates all fields in the corresponding row. For this reason, double-check the values in all editable fields before applying changes. After you click Apply, a popup window appears asking you to confirm the save operation: Click OK to confirm, or click Cancel to abort. To View Monitors To review the monitor parameters for the chosen module, click the Monitors submenu option.
Chapter 7 ICIM Web Interface Module CLI and SNMP Equivalents The information displayed on this page may also be seen by entering CLI commands in the ICIM2 or by viewing the MIB objects via SNMP. The corresponding CLI commands or MIB objects are listed below.
Using Module Details ICIM Web Interface CLI Command Field (for module in chassis 3, slot 7) SNMP MIB Table Module Details / Controls 03/07 module> show control * p2moduleControlTable Module Details / Monitors 03/07 module> show monitor * p2moduleMonitorTable Current Alarms 03/07 module> alarm p2moduleCurrentAlarmTable For additional information, see the Prisma II Enhanced Management System Guide, System Release 2.04, part number 4025559.
Chapter 7 ICIM Web Interface Using System Settings The System Settings page allows users with Admin privileges to review and, where possible, change settings that control Login functionality, the event log, and SNMP traps. To change any of these settings, click in the appropriate field and type the desired setting. To save the changes, click the Apply button beneath the settings table, or press Enter. To cancel an entry and restore the previous setting, click the Cancel button before clicking Apply.
Using System Settings The inactivity timeout applies to CLI and Web sessions alike. If a Web session is improperly closed, i.e., if the browser is closed before logging out, the inactivity timeout determines how long the session will "hang." Lockout Interval - the length of time that users are prevented from logging in after they reach the maximum number of login attempts. This parameter may be set from 1 to 60 minutes, or may be set to 0 to disable User Lockout.
Chapter 7 ICIM Web Interface All trap destinations are IP addresses with SNMP Managers. SNMP Managers are entities such as notification groups, dispatch centers, and work order generation systems that take specified actions on receipt of the trap.
Using the Event Log Using the Event Log Clicking the Event Log menu item displays the event log, which lists the significant actions performed by each system user. You can view the event log and completely clear its contents, if desired. To View the Event Log To access the event log, click the Event Log menu item. If the event log contains more than one page, a page navigation control appears above the left side of the event log table. To advance in the table, click Next or a higher page number.
Chapter 7 ICIM Web Interface To return to a previous page in the table, click Previous or a lower page number. The Event Log table lists the following information. Timestamp - The time at which the event was logged. Action - The name of the event that triggered the log entry. User ID - The login name of the user who performed the action. Description - A brief description of the action that triggered the log entry. Sec Level - The security level of the user who performed the event.
User Management User Management The User Management page allows users with Admin privileges to manage ICIM2 user accounts. Users may log in through the CLI or the ICIM Web Interface. The User Management table lists all user records and their status. You can add a new user, edit the security information for an existing user, change a password, or unlock user accounts. If a user is deleted, there is no further record of the user apart from any related information saved in the event log.
Chapter 7 ICIM Web Interface Complete the following steps to fill in the New User Information form. 1 Click inside the User ID field and enter the user ID number for the user. 2 Click inside the Password field and enter a password for the new user. Note: User ID and Password security protocols are enforced. 3 Click the Security Level drop-down arrow and choose the correct security level for the new user (Read-Only, Read-Write, Admin).
User Management 3 a Open the Security Level drop-down menu and select the appropriate menu option (Read-Only, Read-Write, Admin). b Click the Save button to the right of the Security Level field to save the change, or click Cancel to abort. If necessary, change the status for the user as follows: a b 4 Open the Status drop-down menu and select one of the following menu options: – Enabled, to make the user record active immediately.
Chapter 7 ICIM Web Interface Web Interface Help The Web Interface Help page provides general help on the pages available from the web server built into the ICIM2. The left side of the page contains a navigation pane similar to that found on other pages of the ICIM Web Interface. However, there are two important differences: Rather than jump to a page in the ICIM Web Interface, the links in the Help navigation pane jump to the help section for that page.
Web Interface Help All Help sections are on a single page, so you can access a particular section either by using the navigation pane to jump to the section or simply by scrolling down the page. Help Menu Clicking the Help option opens a menu of Help subjects. This menu works like the navigation pane on all other pages, except that the links navigate not to the indicated page but to the specific Help section for that page.
8 Chapter 8 Customer Support Information Introduction This chapter contains information on obtaining product support and returning products to Scientific Atlanta. In This Chapter 4025561 Rev A Obtaining Product Support ............................................................... 212 Return Product for Repair .................................................................
Chapter 8 Customer Support Information Obtaining Product Support IF… THEN… you have general questions about this product contact your distributor or sales agent for product information or refer to product data sheets on www.cisco.com. you have technical questions about this product call the nearest Technical Service center or Scientific Atlanta office.
Obtaining Product Support Region Centers Telephone and Fax Numbers Brazil Brazil For Technical Support, call: Telephone: 55-11-3845-9154 ext 230 Fax: 55-11-3845-2514 For Customer Service or to request an RMA number, call: Telephone: 55-11-3845-9154, ext 109 Fax: 55-11-3845-2514 E-mail: luiz.fattinger@sciatl.
Chapter 8 Customer Support Information Return Product for Repair You must have a return material authorization (RMA) number to return a product. Contact the nearest customer service center and follow their instructions.
Return Product for Repair 4 In-warranty products can accrue costs through damage, misuse, cosmetics, or if no problem is found. Products incurring costs will not be returned to you without a valid purchase order number. Once an RMA number has been issued, a confirmation e-mail or fax will be sent to you detailing the RMA number, product and product quantities authorized for return, together with shipping address details and RMA terms and conditions.
Chapter 8 Customer Support Information Complete the following steps to fill out the Scientific Atlanta Transmission Networks repair tag. 1 216 Complete header information. RMA Number: Enter the RMA number provided by the Scientific Atlanta customer service representative. All RMA numbers start with “3” and are followed by 7 additional digits. An RMA number is required to return products to Scientific Atlanta. If you are the technician who is filling out this tag, you may not have the RMA number.
Return Product for Repair 2 Company and City: Enter the company name and city of the customer who owns the unit to be returned for repair. SA Part # and Serial #: Enter the part number and serial number of the unit you are returning for repair. The part number and serial number can usually be found on a bar code label on the outside of the unit. If this information can’t be found leave this blank. Product: Enter the model description of the unit you are returning for repair.
Chapter 8 Customer Support Information – If the failure happens only at specific environmental conditions (i.e., at hot temperature). – If the failure is intermittent or constant. – How you were powering the unit when it failed? (DC vs. AC, voltage levels, etc.) Important: Descriptions like “bad unit,” “failed,” or “no HBO” are not specific enough to be helpful. Technician and Phone Number: Enter the name and phone number of the technician completing the failure description information.
Return Product for Repair 3 Ship the product to the address provided by the customer service representative in the confirmation e-mail or fax. Note: Scientific Atlanta does not accept freight collect. Be sure to prepay and insure all shipments. For both in-warranty and out-of-warranty repairs, you are responsible for paying your outbound freight expense, any applicable import and/or export duties and taxes. Scientific Atlanta will pay the return freight expense for in-warranty repairs.
A Appx auto letter Appendix A Prisma II Permitted CLI Commands Introduction The following tables summarize the available CLI commands for the Prisma II Enhanced Management System Platform. Each table lists the commands available for one of the four major CLI prompts: CLI, */* MODULE, TERMINAL, and ICIM. Entries shown in parenthesis () are module-specific and must be typed in full. Hints are given to display available entries for those cases.
Appendix A Prisma II Permitted CLI Commands From CLI ALARM CLEAR DATE EXIT HELP ALARM CLEAR COMMANDS DATE EDIT EXIT ICIM LOGOUT MANUAL MODULE TERMINAL WHO WHOAMI ICIM LOGOUT MANUAL MODULE TERMINAL WHO WHOAMI '?' 222 4025561 Rev A
From ICIM From ICIM ALARM EVENTLOGCLEAR EVENTLOGFILTER HARDWARE ON/OFF PROVISIONING ON/OFF SYSTEM ON/OFF IP (IP_ADDRESS) NAME (FILENAME) PASSWORD (PASSWORD) PATH (PATH) USER (USERNAME) ADD (IP_ADDRESS) DELETE (IP_ADDRESS) EXIT FILE HELP IKE INFO ACTIVEREV ATTNSTATUS BOOTREV CHASSIS CLEI CLLI COMMREAD COMMTRAP COMMWRITE DEVTYPE DOWNLDCMD DOWNLDDIR DOWNLDFILE DOWNLDRESULT DOWNLDSEM DOWNLDSIG DOWNLDSTATE 4025561 Rev A 223
Appendix A Prisma II Permitted CLI Commands DOWNLDTGT DOWNLDUSER FTPSERVER FTPUSER GATEWAY HWREV INACTIVEREV IP IPSEC LOCKOUT MAC MANDATA NEXTIMAGE PREVIOUSIP SELFTEST SERIAL SIZE SLOT SMC STATUSMSG SUBNET SWDATE SWREV THRESHOLD TIMEOUT TOS TZONE UPDATEID IPROUTE ADD (DESTINATION) (GATEWAY) DELETE (DESTINATION) (GATEWAY) IPSEC 224 DISABLE 4025561 Rev A
From ICIM ENABLE LOGOUT MANUAL REBOOT SET SHOW CLLI (CLLI) CLOCK (DATE_TIME) COMMREAD (READ_STRING) COMMTRAP (TRAP_STRING) COMMWRITE (WRITE_STRING) GATEWAY (GATEWAY) IP (IP_ADDRESS) LOCKOUT (INTERVAL) STATUSMSGCLEARKEY (1) SUBNET (SUBNET_MASK) THRESHOLD (THRESHOLD) TIMEOUT (TIMEOUT) TZONE (TIMEZONE) UPDATEID (1) ACTIVEREV ATTNSTATUS BOOTREV CHASSIS CLEI CLLI CLOCK COMMREAD COMMTRAP COMMWRITE DEVTYPE DOMAIN DOWNLDCMD DOWNLDDIR DOWNLDFILE 4025561 Rev A 225
Appendix A Prisma II Permitted CLI Commands DOWNLDRESULT DOWNLDSEM DOWNLDSIG DOWNLDSTATE DOWNLDTGT DOWNLDUSER EVENTLOG EVENTLOGALL EVENTLOGFILTER FILE FTPSERVER FTPUSER GATEWAY HWREV IKE INACTIVEREV IP IPROUTE IPSEC LOCKOUT LOCKEDUSERS MAC MANDATA NEXTIMAGE PREVIOUSIP PROVISIONING SELFTEST SERIAL SIZE SLOT SMC SNTP STATUSMSG 226 4025561 Rev A
From ICIM SUBNET SWDATE SWREV THRESHOLD TIMEOUT TOS TRAPS TZONE UPDATEID USER SNTP INTERVAL IP MODE STATE TIMEOUT TRAPS DISABLE (INDEX) (IP_ADDRESS) ENABLE (INDEX) (IP_ADDRESS) USER ADD (USER_ID) ADMIN DISABLE ENABLE READ DISABLE ENABLE READWRITE DISABLE ENABLE CHANGE ACCESS_RIGHTS (USER_ID) ADMIN READ READWRITE ACCOUNT_STATUS (USER_ID) DISABLE ENABLE PASSWORD 4025561 Rev A DELETE (USER_ID) UNLOCK (USER_ID) (USER_ID) (PASSWORD) 227
Appendix A Prisma II Permitted CLI Commands '?' 228 4025561 Rev A
From */* MODULE From */* MODULE ALARM DOMAIN MODULE CHASSIS (digits) * [range] EXIT HELP INFO ALARM (ALARMNAME) HYSTERESIS use show alarms * INDEX LABEL LIMITADJUST MAJORHIGH MAJORLOW MINORHIGH MINORLOW NOMINAL RANGEHI RANGELO TYPE VALUE CONTROL (CONTROLNAME) INDEX use show control * LABEL RANGEHI RANGELO RANGESTEP STATENAMES TYPE UNITS VALUE MODULE ACTIVEREV BOOTREV CLEI 4025561 Rev A 229
Appendix A Prisma II Permitted CLI Commands CLLI CODEREV DATECODE DEVTYPE DOWNLOADABLE INACTIVEREV MANDATA MODTYPE NAME NEXTIMAGE NUMANALOGCONTROLS NUMCONTROLS NUMDIGITALCONTROLS NUMMONITS NUMOFALARMS SCRIPTREV SELFTEST SERIAL TOS MONITOR (MONITORNAME) INDEX use show mon * LABEL STATENAMES TYPE UNITS VALUE LOGOUT MANUAL MODID digits * [range] RESET SET ALARMPARAM (ALARMNAME) HYSTERESIS MAJORHIGH 230 4025561 Rev A
From */* MODULE MAJORLOW MINORHIGH MINORLOW SHOW CONTROL (CONTROLNAME) (VALUE) MODULE CLLI (CLLI) ALARMPARAM (ALARMNAME) HYSTERESIS use show alarms * MAJORHIGH MAJORLOW MINORHIGH MINORLOW ALARMSTATE (ALARMNAME) CONTROL (CONTROLNAME) MODULE MONITOR SLOT (MONITORNAME) digits * [range] '?' 4025561 Rev A 231
Appendix A Prisma II Permitted CLI Commands From TERMINAL ALARM COLSEP (string) EXIT HEADERS (digits) HELP LOGOUT MANUAL PAGING (digits) PATTERN REGEX WILDCARD SHOW '?' 232 4025561 Rev A
B Appx auto letter Appendix B Features Available via Remote User Interface Introduction This appendix lists the features of the remote user interface and identifies the availability (CLI, Web Interface, or both) and required user access level (Read-Only, Read-Write, or Admin) for each feature. In This Appendix 4025561 Rev A Overview.............................................................................................. 234 ICIM Data..............................................
Appendix B Features Available via Remote User Interface Overview The tables below list the features available via either the CLI or the Web Interface. Symbols appearing in the cells of these tables have the meanings described below. In the CLI or Web column: - An asterisk (*) indicates that the corresponding interface (CLI or Web) supports this feature. - A dash (-) indicates that the corresponding interface (CLI or Web) does not support this feature.
ICIM Data ICIM Data 4025561 Rev A Feature CLI Web Read-Only User Privilege Read-Write User Privilege Admin User Privilege IP address *1 * R R RW Active rev * * R R R Attnstatus * - R R R Boot rev * - R R R Chassis * * R R R CLEI * * R R R CLLI * * R RW RW Clock *1 * R R RW Commread * - - - RW Commwrite * - - - RW Commtrap * - - - RW DevType * - R R R Domain * * R R R Downldcmd * - R R R Downlddir * - R R R Dow
Appendix B Features Available via Remote User Interface 236 Feature CLI Web Read-Only User Privilege Read-Write User Privilege Admin User Privilege Hwrev * * R R R Inactiverev * * R R R IKE 2 * - - - RW IProute * - R R RW IPSec 3 * - R R RW LockedUsers * * - - R LockoutInterval * * R R RW MAC * * R R R Mandata * * R R R Nextimage * - R R R Previousip * - R R R Provisioning * - R R R Reboot * - - - W Selftest * * R R R
ICIM Data 4025561 Rev A Feature CLI Web Read-Only User Privilege Read-Write User Privilege Admin User Privilege sysLocation - * R R R sysUptime - * R R R Threshold *4 * R R RW Timeout *4 * R R RW TOS * * R R R Traps *4 * R R RW Timezone *1 * R R RW Updateid * - R R RW User * * - - RW 1 May be modified through the CLI but not through the ICIM Web Interface. 2 IKE Peers may be added via Telnet only if IPsec is enabled.
Appendix B Features Available via Remote User Interface Module Data 238 Feature CLI Web Read-Only User Privilege Read-Write User Privilege Admin User Privilege Active rev * * R R R Boot rev * - R R R Chassis * * R R R CLEI * * R R R CLLI * * R RW RW Device Type * * R R R Downloadable * * R R R Inactive Rev * * R R R Module Name * * R R R Module Type * * R R R Reset * - - - W Selftest * * R R R Serial * * R R R Slot * *
Current Alarms Current Alarms 4025561 Rev A Feature CLI Web Read-Only User Privilege Read-Write User Privilege Admin User Privilege Current Alarms * * R R R 239
Appendix B Features Available via Remote User Interface Module Alarms 240 Feature CLI Web Read-Only User Privilege Read-Write User Privilege Admin User Privilege Hysteresis * * R RW RW Label * * R R R MajorHigh * * R RW RW MajorLow * * R RW RW MinorHigh * * R RW RW MinorLow * * R RW RW RangeHigh * * R R R RangeLow * * R R R Type * * R R R Value * * R R R 4025561 Rev A
Module Controls Module Controls 4025561 Rev A Feature CLI Web Read-Only User Privilege Read-Write User Privilege Admin User Privilege High * * R R R Label * * R R R Low * * R R R Step * * R R R Units * * R R R Value * * R RW RW 241
Appendix B Features Available via Remote User Interface Module Monitors 242 Feature CLI Web Read-Only User Privilege Read-Write User Privilege Admin User Privilege Label * * R R R Units * * R R R Value * * R R R 4025561 Rev A
System Information System Information Feature CLI Web Read-Only User Privilege Read-Write User Privilege Admin User Privilege Event Log Filter *4 * R R RW Event Log Clear * * - - R/Clear Max Login Attempts *4 * R R RW Inactivity Timeout *4 * R R RW Lockout Interval * * R R RW Trap Receive Table *4 * R R RW 4 4025561 Rev A May be read through the CLI but not through the ICIM Web Interface.
Appendix B Features Available via Remote User Interface User Management Feature CLI Web Read-Only User Privilege Read-Write User Privilege Admin User Privilege Add user * * - - RW Change user * * - - RW Current users * * - - R Delete user * * - - RW Unlock user * -1 - - RW A user account may be unlocked through the ICIM Web Interface by enabling the account.
C Appx auto letter Appendix C Module Parameter Descriptions Introduction This appendix provides tables of manufacturing data, monitored parameters, configurable parameters, and alarms for each Prisma II application module. The values in the tables vary from module to module. The examples shown are for guidance only.
In This Appendix 246 Split and Non-Split Mode for Power Supply and Fan Tray ......... 247 Power Supply and Fan Tray Parameters (Non-Split).................... 250 Fan Tray Parameters (Split)............................................................... 253 Power Supply 1 Parameters (Split)................................................... 255 Power Supply 3 Parameters (Split)................................................... 257 Pre-Amplifier FTTP Parameters ..........................
Split and Non-Split Mode for Power Supply and Fan Tray Split and Non-Split Mode for Power Supply and Fan Tray This section explains the difference between Split and Non-Split mode reporting of Prisma II EMS power supply and fan tray module parameters. Overview All Prisma II EMS system releases associate fan tray and power supply parameters with chassis slot numbers. In System Release 1.
Appendix C Module Parameter Descriptions All changes made in System Release 1.01 to support Split mode fan tray and power supply parameters persist in System Release 2.00 and later. Alarm Parameters Alarm parameters are individual alarms that indicate the status of a single function or condition of a module. The table below lists the alarm parameters for Prisma II Enhanced Management System fan tray and power supply modules and identifies their corresponding functions.
Split and Non-Split Mode for Power Supply and Fan Tray Parameter Function Associated Slot Non-Split Mode (Release 1.00) Associated Slot Split Mode (Release 1.
Appendix C Module Parameter Descriptions Power Supply and Fan Tray Parameters (Non-Split) Power Supply/Fan Tray Alarm Data Parameters Alarm Function Major Low Threshold Minor Low Threshold Minor High Threshold Major High Threshold Hysteresis Typical Range/ Nom. Value FansOk Fan status na na na na na OK or Fault ChasTemp Fan tray temp -40 -35 60 65 1 -40°C to 65°C Ps1PwrIn Slot 1 input power na na na na na OK or Fault Ps1+24 Slot 1 +24 voltage 18.0 18.4 25.9 26.1 0.
Power Supply and Fan Tray Parameters (Non-Split) Power Supply/Fan Tray Manufacturing Data Parameter Examples Manufacturing Data Typical Values Module Name Power Supply 1 / Fan Tray Set in Manufacturing (example value shown) OR Power Supply 3 / Fan Tray Module Type 5010 Serial # [1] AALR1RL X Date Code [1] J04 X Sw Ver [1] 1.00.
Appendix C Module Parameter Descriptions Parameter Function Initial Value Operating Value (typ) ChasTemp Fan tray internal temperature 36.02°C 36.02°C FansOn 1 if fans are running, 0 if shut off 1 (ON) 1 (ON) Note: All monitored values may vary from module to module. The values shown above are examples only.
Fan Tray Parameters (Split) Fan Tray Parameters (Split) Fan Tray Alarm Data Parameters Alarm Function Major Low Threshold Minor Low Threshold Minor High Threshold Major High Threshold Hysteresis Typical Range/ Nom.
Appendix C Module Parameter Descriptions Fan Tray Monitor Parameter Examples Parameter Function Initial Value Operating Value (typ) Ps1Inst 1 if slot 1 PS installed, 0 if not 1 (Inst) 1 (Inst) Ps3Inst 1 if slot 3 PS installed, 0 if not 1 (Inst) 1 (Inst) Chas+24V chassis +24 V rail 24.14V 24.14V Chas+5V chassis +5 V rail 5.08V 5.08V Chas-5V chassis -5 V rail -5.05V -5.05V ChasTemp fan tray internal temperature 36.02°C 36.
Power Supply 1 Parameters (Split) Power Supply 1 Parameters (Split) Power Supply 1 Alarm Data Parameters Alarm Function Major Low Threshold Minor Low Threshold Minor High Threshold Major High Threshold Hysteresis Typical Range/ Nom. Value Ps1PwrIn Slot 1 input power na na na na na OK or Fault Ps1+24 Slot 1 +24 voltage 18.0 18.4 25.9 26.1 0.1 23.8 to 25.6 VDC Ps1+5VDC Slot 1 +5 voltage 3.6 3.7 5.9 6.1 0.1 4.9 to 5.3 VDC Ps1-5VDC Slot 1 -5 voltage -5.6 -5.5 -4.6 -4.5 0.
Appendix C Module Parameter Descriptions Note: [1] These values are not visible from the ICIM2 front panel. Power Supply 1 Monitor Parameter Examples Parameter Function Initial Value Operating Value (typ) Ps1+24V measured +24 V DC of slot 1 24.97V 24.97V Ps1+5V measured +5 V DC of slot 1 5.38V 5.38V Ps1-5V measured -5 V DC of slot 1 -5.42V -5.42V Ps1Temp internal slot 1 PS temperature 32.7°C 32.7°C Note: All monitored values may vary from module to module.
Power Supply 3 Parameters (Split) Power Supply 3 Parameters (Split) Power Supply 3 Alarm Data Parameters Alarm Function Major Low Threshold Minor Low Threshold Minor High Threshold Major High Threshold Hysteresis Typical Range/ Nom. Value Ps3PwrIn Slot 3 input power na na na na na OK or Fault Ps3+24 Slot 3 +24 voltage 18.0 18.4 25.9 26.1 0.1 23.8 to 25.6 VDC Ps3+5VDC Slot 3 +5 voltage 3.6 3.7 5.9 6.1 0.1 4.9 to 5.3 VDC Ps3-5VDC Slot 3 -5 voltage -5.6 -5.5 -4.6 -4.5 0.
Appendix C Module Parameter Descriptions Note: [1] These values are not visible from the ICIM2 front panel. Power Supply 3 Monitor Parameter Examples Parameter Function Initial Value Operating Value (typ) Ps3+24V measured +24 V DC of slot 3 25.03V 25.03V Ps3+5V measured +5 V DC of slot 3 5.38V 5.38V Ps3-5V measured -5 V DC of slot 3 -5.43V -5.43V Ps3Temp internal slot 3 PS temperature 28.7°C 28.7°C Note: All monitored values may vary from module to module.
Pre-Amplifier FTTP Parameters Pre-Amplifier FTTP Parameters Pre-Amplifier Nominal Alarm Values The table below lists the OutPwr nominal alarm values for this module. Nominal alarm values cannot be changed by the user. Model Nominal Alarm Value Attenuator Setting Prisma II Pre-Amplifier FTTP (1 x 19 dBm) 19.0 dBm 0 Prisma II Pre-Amplifier FTTP (2 x 17 dBm) 17.0 dBm 0 Prisma II Pre-Amplifier FTTP (2 x 19 dBm) 19.0 dBm 0 Prisma II Pre-Amplifier FTTP (1 x 21.5 dBm) 21.
Appendix C Module Parameter Descriptions [1] This alarm threshold value is relative to the nominal alarm value. [2] This value depends on the pre-amplifier type. See Pre-Amplifier Nominal Alarm Values (on page 259) for possible types and values. [3] This value is set in manufacturing based on the characteristics of the laser diode, and may vary from module to module. Pre-Amplifier Module Alarm Data Parameters Module alarms are set at the factory and may not be adjusted by the user.
Pre-Amplifier FTTP Parameters Pre-Amplifier Control Parameters Control Function Possible Values Default Enable Turns optical amplifier ON or OFF ON (1) OFF (0) OFF (0) SetAtten Optical power attenuation 0 to 3 dB in 1.
Appendix C Module Parameter Descriptions Manufacturing Data Typical Values Set in Manufacturing (Example value shown) VLPIS0TDAA (1 x 21.5 dBm module) VLPIS0SDAA (2 x 17 dBm module) CLLI Code [1] [2] (blank) Note: [1] These values may vary from module to module. The values shown above are examples only. [2] These values are not visible from the ICIM2 front panel.
Post-Amplifier FTTP Parameters Post-Amplifier FTTP Parameters Post-Amplifier Nominal Alarm Values The table below lists the OutPwrA and OutPwrB nominal alarm values for this module. Nominal alarm values cannot be changed by the user. Model Nominal Alarm Value Attenuator Setting Prisma II Post-Amplifier FTTP (18 x 18.9 dBm) 18.90 dBm 0 Prisma II Post-Amplifier FTTP (22 x 18.1 dBm) 18.10 dBm 0 Prisma II Post-Amplifier FTTP (24 x 17.65 dBm) 17.
Appendix C Module Parameter Descriptions Alarm Function Major Low Threshold Minor Low Threshold Minor High Threshold Major High Threshold Hysteresis Typical Range/ Nom. Value LasBiasA Laser bias current A [1] -8.0 -8.0 -0.1 -0.01 0.001 3.7 to 5.0 A [3] LasBiasB Laser bias current B [1] -8.0 -8.0 -0.1 -0.01 0.001 3.7 to 5.0 A [3] Note: [1] This alarm threshold value is relative to the nominal alarm value.
Post-Amplifier FTTP Parameters Alarm Function Major Low Threshold Minor Low Threshold Minor High Threshold Major High Threshold Hysteresis Typical Range/ Nom. Value ServiceB Service mode B na na na na na OK or Fault [4] Note: [1] This alarm threshold value is relative to the nominal alarm value. [2] This alarm sets the unit to the safe state, in which the optical input is disabled.
Appendix C Module Parameter Descriptions Set in Manufacturing (example value shown) Manufacturing Data Typical Values Module Type 3031 Serial # [1] AAFHJLT X Date Code [1] K05 X Sw Ver [1] 1.01.04 In Service Hours [1] 0 (initial value) X Spec Data (MANDATA) [1] 24 x 17.65 X 22 x 18.10 18 x 18.90 CLEI Code [1] [2] X VLPIR0NDAA (24 x 17.65 dBm module) VLPIR0MDAA (22 x 18.1 dBm module) VLPIR0LDAA (18 x 18.
Post-Amplifier FTTP Parameters Parameter Function Initial Value (no input) Operating Value (typ) LasLimA Laser operating current limit A 6.3 A 6.3 A LasLimB Laser operating current limit B 6.3 A 6.3 A ModTemp Module temperature 27°C 30°C LaserOn Laser in service hours 0 hrs (increments) Note: All monitored values may vary from module to module. The values shown above are examples only.
Appendix C Module Parameter Descriptions Optical Transmitter FTTP Parameters Optical Transmitter Alarm Data Parameters Alarm Function Major Low Threshold Minor Low Threshold Minor High Threshold Major High Threshold Hysteresis Typical Range/ Nom. Value InRF RF input power level [1] -2 -1 1 3 0.1 0.0 dBm OutPwr Optical output power [1] -1.5 -1.1 1.1 1.5 0.1 8.
Optical Transmitter FTTP Parameters [1] This alarm threshold value is relative to the nominal alarm value. [2] This alarm threshold value is absolute to the nominal alarm value. [3] This value is set in manufacturing based on the characteristics of the laser diode, and may vary from module to module. [4] This alarm sets the unit to the safe state, in which the lasers are turned off to disable optical output. [5] The alarm values OK and Fault correspond to the control values ON and OFF, respectively.
Appendix C Module Parameter Descriptions Set in Manufacturing (example value shown) Manufacturing Data Typical Values In Service Hours [1] 0 (initial value) X Spec Data (MANDATA) [1] (blank) X CLEI Code [1] [2] VLT3F0HDAD X CLLI Code [1] [2] (blank) Note: [1] These values may vary from module to module. The values shown above are examples only. [2] These values are not visible from the ICIM2 front panel.
Optical Switch FTTP Parameters Optical Switch FTTP Parameters Optical Switch User Alarm Data Parameters User alarms have thresholds that can be set by the user. The default user alarm data for this module is shown below. Low Threshold High Threshold Hysteresis Typical Range/ Nom.
Appendix C Module Parameter Descriptions Optical Switch Control Parameters Parameter Function Possible Values Default Mode Selects Cross, Bar, or Auto mode Cross (0) Auto (2) Bar (1) Auto (2) WaveLen Selects wavelength of input for both inputs 1310 nm (0) 1550 nm (1) NomPin3 Nominal input power at Port 3 in dBm -8.0 to 23.0 dBm, 0.1 dB steps 21.0 dBm NomPin4 Nominal input power at Port 4 in dBm -8.0 to 23.0 dBm, 0.1 dB steps 21.
Optical Switch FTTP Parameters Set in Manufacturing (example value shown) Manufacturing Data Typical Values Sw Ver [1] 1.01.04 In Service Hours [1] 0 (initial value) X Spec Data (MANDATA) [1] (blank) X CLEI Code [1] [2] VLCMKL0EAB X CLLI Code [1] [2] (blank) Note: [1] These values may vary from module to module. The values shown above are examples only. [2] These values are not visible from the ICIM2 front panel.
Glossary A ac, AC alternating current. An electric current that reverses its direction at regularly recurring intervals. AGC automatic gain control. A process or means by which gain is automatically adjusted in a specified manner as a function of input level or other specified parameters. B binding A parameter representing the physical or logical objects associated with a trap. C CAT5 category 5 Ethernet cable. CDE common desktop environment. CLEI common language equipment identifier.
Glossary which fields are separated by commas. Also referred to as comma delimited. D DB-37 37-pin D-sub connector. dc, DC direct current. An electric current flowing in one direction only and substantially constant in value. E EIA Electronic Industries Association. A United States association that provides standards for use between manufacturers and purchasers of electronic products. EMC electromagnetic compatibility. A measure of equipment tolerance to external electromagnetic fields.
Glossary ICIM intelligent communications interface module. IP Internet protocol. A standard that was originally developed by the United States Department of Defense to support the internetworking of dissimilar computers across a network. IP is perhaps the most important of the protocols on which the Internet is based. It is the standard that describes software that keeps track of the internetwork addresses for different nodes, routes, and outgoing/incoming messages on a network.
Glossary P PLL phase lock loop. An electronic servo system controlling an oscillator to maintain a constant phase angle relative to a reference signal. polling In a transmission network system, the active sampling of the status of network devices by a control and monitoring program. R RF radio frequency. The frequency in the portion of the electromagnetic spectrum that is above the audio frequencies and below the infrared frequencies, used in radio transmission systems.
Glossary SNMP simple network management protocol. A protocol that governs network management and the monitoring of network devices and their functions. SOUP software upgrade program. A utility used to update firmware in Prisma II EMS application modules. T TEC thermoelectric cooler. A device used to dissipate heat in electronic assemblies. Telco telephone company.
Index A About Modspecs • 41 ac, AC • 275 AGC • 275 alarm • 22, 44, 103, 159 alarm domain • 45 alarm module • 46 Alarm Parameters • 248 B binding • 275 C CAT5 • 275 CDE • 275 chassis • 47 clear • 23 CLEI • 275 CLI • 275 CLI Command Modes • 12 CLI Login and Logout • 10 CLI Mode Commands • 21 CLI Overview • 7 CLLI • 275 colsep • 160 Command Syntax • 14 Completing the Scientific Atlanta Transmission Networks Repair Tag • 215 Control Parameters • 249 CSV • 276 Current Alarms • 239 Customer Support Information
Index info monitor • 58 Installation • 180 Introduction • 1, 178 IP • 277 iproute • 116 ipsec • 118 ISO • 277 L LCD • 277 LED • 277 Login and Logout • 183 logout • 28, 60, 120, 167 M manual • 30, 61, 121, 168 MIB • 277 modid • 65 module • 32 Module Alarms • 240 Module CLI and SNMP Equivalents • 198 Module Controls • 241 Module Data • 238 Module Mode Commands • 37 Module Monitors • 242 Monitor Parameters • 248 N nm • 277 NMS • 277 O Obtaining an RMA Number and Shipping Address • 214 Obtaining Product Su
Index Pre-Amplifier Manufacturing Data Parameter Examples • 261 Pre-Amplifier Module Alarm Data Parameters • 260 Pre-Amplifier Nominal Alarm Values • 259 Pre-Amplifier User Alarm Data Parameters • 259 Prisma II Enhanced Platform Management Configuration • 8 R reboot • 126 Related Publications • 3 reset • 67 Return Product for Repair • 214 RF • 278 RMA • 278 RT • 278 RTC • 278 RX • 278 S SBS • 278 semaphore • 278 set • 127 set alarmparam • 69 set clock • 129 set control • 74 set module • 78 show • 131, 17
Scientific Atlanta, A Cisco Company 5030 Sugarloaf Parkway, Box 465447 Lawrenceville, GA 30042 678.277.1000 www.scientificatlanta.com This document includes various trademarks of Cisco Systems, Inc. Please see the Notices section of this document for a list of Cisco Systems, Inc., trademarks used in this document. Product and service availability are subject to change without notice. © 2008 Cisco Systems, Inc. All rights reserved.
