Cisco PA-FE-TX and Cisco PA-FE-FX Fast Ethernet 100BASE-T Port Adapter Installation and Configuration Product Number: PA-FE-TX(=) and PA-FE-FX(=) Platforms Supported: Catalyst 5000 Family Switches with RSM/VIP2, Cisco 7100 Series, Cisco 7200 Series, Cisco uBR7200 Series, Cisco 7301 Routers, Cisco 7401ASR Routers, and VIP in the Cisco 7000 Series and Cisco 7500 Series Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
C O N T E N T S Preface vii Objectives Organization vii viii Related Documentation viii Obtaining Documentation x Cisco.com x Documentation CD-ROM x Ordering Documentation x Documentation Feedback xi Obtaining Technical Assistance xi Cisco.com xi Technical Assistance Center xi Cisco TAC Website xii Cisco TAC Escalation Center xii Obtaining Additional Publications and Information CHAPTER 1 Overview 1-1 Fast Ethernet Overview 1-1 Port Adapter Overview 1-2 IEEE 802.
Contents Interface Addresses of Cisco 7100 Series Routers 1-23 Interface Addresses of Cisco 7200 Series Routers, Cisco 7200 VXR Routers, and Cisco uBR7200 Series Routers 1-23 Interface Addresses of Cisco 7301 Router 1-23 Interface Addresses of Cisco 7401ASR Router 1-23 Interface Addresses of Cisco 7500 Series Routers with VIP 1-24 CHAPTER 2 Preparing for Installation 2-1 Required Tools and Equipment 2-1 Minimum Software and Hardware Requirements Checking Hardware and Software Compatibility 2-3 Saf
Contents CHAPTER 4 Configuring the PA-FE-TX or PA-FE-FX Using the EXEC Command Interpreter 4-1 4-1 Configuring the Interfaces 4-2 Performing a Basic Configuration 4-2 Configuring PA-FE-TX or PA-FE-FX Transmission Mode Configuring PA-FE-TX or PA-FE-FX Media Type 4-4 4-4 Checking the Configuration 4-5 Using show Commands to Verify the Interface Status 4-5 Using the show controllers Commands 4-6 Using the show protocols Command 4-6 Using the show running-config Command 4-6 Using the show startup-config
Contents Cisco PA-FE-TX and Cisco PA-FE-FX Fast Ethernet 100BASE-T Port Adapter Installation and Configuration vi OL-2899-02
Preface This preface describes the objectives and organization of this document and explains how to find additional information on related products and services.
Preface Organization Organization This document contains the following chapters: Section Title Description Chapter 1 Overview Describes the PA-FE-TX and PA-FE-FX and their LED displays, cables, and receptacles. Chapter 2 Preparing for Installation Describes safety considerations, tools required, and procedures you should perform before the actual installation.
Preface Related Documentation – For hardware installation and maintenance information (including the Cisco 7206 or Cisco 7206VXR as a router shelf in a Cisco AS5800 Universal Access Server), refer to the installation and configuration guide that shipped with your Cisco 7200 series router.
Preface Obtaining Documentation Obtaining Documentation Cisco provides several ways to obtain documentation, technical assistance, and other technical resources. These sections explain how to obtain technical information from Cisco Systems. Cisco.com You can access the most current Cisco documentation on the World Wide Web at this URL: http://www.cisco.com/univercd/home/home.htm You can access the Cisco website at this URL: http://www.cisco.
Preface Obtaining Technical Assistance Documentation Feedback You can submit comments electronically on Cisco.com. On the Cisco Documentation home page, click Feedback at the top of the page. You can e-mail your comments to bug-doc@cisco.com. You can submit your comments by mail by using the response card behind the front cover of your document or by writing to the following address: Cisco Systems Attn: Customer Document Ordering 170 West Tasman Drive San Jose, CA 95134-9883 We appreciate your comments.
Preface Obtaining Technical Assistance • Priority level 3 (P3)—Your network performance is degraded. Network functionality is noticeably impaired, but most business operations continue. • Priority level 2 (P2)—Your production network is severely degraded, affecting significant aspects of business operations. No workaround is available. • Priority level 1 (P1)—Your production network is down, and a critical impact to business operations will occur if service is not restored quickly.
Preface Obtaining Additional Publications and Information Obtaining Additional Publications and Information Information about Cisco products, technologies, and network solutions is available from various online and printed sources. • The Cisco Product Catalog describes the networking products offered by Cisco Systems as well as ordering and customer support services. Access the Cisco Product Catalog at this URL: http://www.cisco.com/en/US/products/products_catalog_links_launch.
Preface Obtaining Additional Publications and Information Cisco PA-FE-TX and Cisco PA-FE-FX Fast Ethernet 100BASE-T Port Adapter Installation and Configuration xiv OL-2899-02
C H A P T E R 1 Overview This chapter describes the Cisco PA-FE-TX and Cisco PA-FE-FX port adapters and contains the following sections: • Fast Ethernet Overview, page 1-1 • Port Adapter Overview, page 1-2 • IEEE 802.
Chapter 1 Overview Port Adapter Overview • 100BASE-TX—100BASE-T, half- and full-duplex over Category 5 unshielded twishted-pair (UTP), Electronics Industry Association/Telecommunications Industry Association (EIA/TIA)–568-compliant cable • 100BASE-FX—100BASE-T, half- and full-duplex over optical fiber Each physical layer protocol has a name that summarizes its characteristics in the format speed/signaling method/segment length, where speed is the LAN speed in megabits per second (Mbps), signaling met
Chapter 1 Overview IEEE 802.3u 100BASE-T Specifications IEEE 802.3u 100BASE-T Specifications This section provides specifications for IEEE 802.3u 100BASE-T. Table 1-1 provides cabling specifications for 100BASE-TX Fast Ethernet transmission over UTP and foil twisted-pair (FTP), and 100BASE-FX Fast Ethernet over fiber-optic cables. It also summarizes IEEE 802.3u 100BASE-TX and 100BASE-FX physical characteristics. (See Figure 1-3).
Chapter 1 Overview LEDs Figure 1-3 Maximum Segment and Network Lengths—100BASE--FX adn 100BASE--TX Maximum segment length, full duplex 100 m TX DTE* DTE 2000 m FX–multimode Maximum segment length, full duplex 10,000 m FX–single mode DTE DTE Maximum segment length, half duplex 100 m TX DTE DTE 412 m FX Maximum network length, half duplex DTE 200 m TX R (Repeater) DTE **Because repeaters have more delay, total network length is shorter.
Chapter 1 Overview Cables, Connectors, and Pinouts Table 1-2 lists port LED colors and indications. Table 1-2 PA-FE-TX and PA-FE-FX LEDs LED Label Color State Meaning ENABLED Green On The PA-FE-TX or PA-FE-FX is correctly connected and receiving power, it contains a valid microcode version, and the bus recognizes the PA-FE-TX or PA-FE-FX port adapter or the PA-FE-equipped VIP or Catalyst RSM/VIP2.
Chapter 1 Overview Cables, Connectors, and Pinouts Warning Note The ports labeled “Ethernet,” “10BaseT,” “Token Ring,” “Console,” and “AUX” are safety extra-low voltage (SELV) circuits. SELV circuits should only be connected to other SELV circuits. Because the BRI circuits are treated like telephone-network voltage, avoid connecting the SELV circuit to the telephone network voltage (TNV) circuits.
Chapter 1 Overview Cables, Connectors, and Pinouts PA-FE-FX Duplex SC Connector H2214 Figure 1-9 H2399 Figure 1-10 PA-FE-FX Simplex SC Connector Depending on the type of media you use between the MII connection on the port adapter and your switch or hub, the network side of your 100BASE-T transceiver should be appropriately equipped with SC-type connectors (for optical fiber), BNC connectors, and so forth. Figure 1-11 shows the pin orientation of the female MII connector on the port adapter.
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms Table 1-3 MII Connector Pinout Pin1 In Out In/Out Description 14–17 – Yes – Transmit Data (TxD) 12 Yes – – Transmit Clock (Tx_CLK)2 11 – Yes – Transmit Error (Tx_ER) 13 – Yes – Transmit Enable (Tx_EN) 3 – Yes – MII Data Clock (MDC) 4–7 Yes – – Receive Data (RxD) 9 Yes – – Receive Clock (Rx_CLK) 10 Yes – – Receive Error (Rx_ER) 8 Yes – – Receive Data Valid (Rx_DV) 18 Yes – – Co
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms Catalyst 5000 Family Switches with RSM/VIP2 Slot Numbering The Catalyst 5000 switch chassis has five slots. (See Figure 1-12.) Slot 1 is for the supervisor engine. Slots 2 through 5 are available for modules. Figure 1-12 Catalyst 5000 Switch with Modules Installed Power supply 2 H10645 Power supply 1 Switching modules Supervisor engine The Catalyst 5500 switch chassis has 13 slots. (See Figure 1-13 on page 1-10.
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms Figure 1-13 Catalyst 5500 Switch with Modules Installed Supervisor engine modules 1 PO RT M bp s 10 0 NK M II M DI X M II 1 PO RT 10 LI NK 0 M bp s ST AT US M II M DI X M II M DI X SUPERVISOR ENGINE 2 PO RT 10 LI NK 0 M bp s PS PS 2 1 FA N SY STA STE TU M S M DI X LI SUPERVISOR ENGINE 2 PO RT 10 LI NK 0 M bp s 1% SW IT LO CH G CO NSO LE SW IT LO CH G 1% 10 0% FA N PS PS 2 1 CO NSO LE 10 0% RES
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms Figure 1-14 Catalyst 5505 Switch with Modules Installed Power supply 2 H10964 Power supply 1 Switching modules Supervisor engine The Catalyst 5509 switch chassis has nine slots. (See Figure 1-15.) Slot 1 is for the supervisor engine. Slot 2 can contain a redundant supervisor engine. If a redundant supervisor engine is not required, slots 2 through 9 are available for modules.
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms Note Refer to the Catalyst 5000 Series Route Switch Module Installation and Configuration Note for any additional slot restrictions for the Catalyst RSM/VIP2. Cisco 7000 Series Routers with VIP Slot Numbering Figure 1-16 shows a partial view of a VIP motherboard with installed modules. With the motherboard oriented as shown in Figure 1-16, the left module is in slot 0, and the right module is in slot 1.
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms Figure 1-17 Cisco 7000 Interface Slot Numbers Captive installation screw DC FA IL AC PO WE R Upper power supply I O Captive installation screw H2358 DC FA IL AC PO WE R Lower power supply I O Slot 0 1 2 3 4 SP RP or slot SSP slot Figure 1-18 Cisco 7010 Interface Slot Numbers RP slot SP or SSP slot Interface processor slot 2 Interface processor slot 1 Interface processor slot 0 H2359 Power switch Chassis ground scr
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms Cisco 7100 Series Routers Slot Numbering The PA-FE-TX and PA-FE-FX can be installed in port adapter slot 3 in Cisco 7120 series routers, and in port adapter slot 4 in Cisco 7140 series routers. Figure 1-19 shows a Cisco 7120 with a port adapter installed in slot 3. Figure 1-20 shows a Cisco 7140 with a port adapter installed in slot 4.
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms Cisco 7200 Series Routers, Cisco 7200 VXR Routers, and Cisco uBR7200 Series Routers Slot Numbering Slots in the Cisco 7202 router are numbered from left to right, slot 1 and slot 2. (See Figure 1-21.
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms The Cisco 7204VXR has four slots (slot 1 through slot 4) for modules, one slot for an input/output (I/O) controller, and one slot for a network processing engine or network services engine. You can place the modules in any of the four available slots. (See Figure 1-23.
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms Figure 1-25 Module Slots in the Cisco 7206VXR Port adapter slot 6 Port adapter slot 4 Port adapter slot 2 Blank port adapter 3 2 1 0 6 TOKEN RING 5 FAST ETHERNET 4 K RJ4 0 LIN MII 5 D LE AB EN 0 TX 2 RX 4 TX RX 3 TX RX 2 TX 1 RX TX EN ETHERNET-10BFL CD LB RC RD TC TD CD LB RC RD TC TD CD LB RC RD TC TD CD LB RC RD TC TD EN FAST SERIAL RX 3 3 2 2 1 0 LINK 1 0 3 EN AB LE D
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms Figure 1-27 shows the slot numbering of modules installed on a Cisco uBR7246 router. The slots are numbered slot 1 and slot 2 for the Cisco uBR7246 router. (Slot 0 is always reserved for the Fast Ethernet port on the I/O controller—if present.
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms Figure 1-28 Module Slots in the Cisco uBR7246VXR Port adapter slot 0 (I/O controller) Port adapter slot 1 (blank) Port adapter slot 2 uBR - CLK-T1 SEC LOS ACTIVE FAULT 5 uBR - MCI6 5 uBR - MCI6 5 uBR - MCI6 5 uBR - MCI6 D S 4 U S 3 U S 2 U S 1 U S U S D LE AB 0 D S 2 U S 1 U S U S D LE AB 0 D S 2 U S 1 U S U S D LE AB 0 31501 D S 2 U S 1 U S U S D LE AB 0 EN U S EN U S EN U S EN
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms Cisco 7401ASR Router Slot Numbering Figure 1-30 shows the front view of a Cisco 7401ASR router with a port adapter installed. There is only one port adapter slot in a Cisco 7401ASR router.
Chapter 1 Overview Identifying Interface Addresses Figure 1-32 Interface Slot Numbers—Cisco 7505 Shown CO NS OL E HA LT ROUTE SWITCH PROCESSOR RE SE T CP U EJ EC T SL SLO OT T 0 1 NO RM AL VIP in interface processor slot 3 Slot 3 Slot 2 Interface processor Slot 1 slots 29619 Slot 0 Identifying Interface Addresses This section describes how to identify interface addresses for the PA-FE-TX and PA-FE-FX in supported platforms.
Chapter 1 Overview Identifying Interface Addresses Interface Addresses of the Catalyst 5000 Family Switches with RSM/VIP2 The interface address for a module on the Catalyst 5000 family switch with RSM/VIP2 is composed of a two-part number in the format slot/port-number. The first number identifies the slot in which the module is installed. Module slots are numbered from top to bottom starting with 1. The second number identifies the physical port number on the module.
Chapter 1 Overview Identifying Interface Addresses Interface Addresses of Cisco 7100 Series Routers The interface address for a module installed on a Cisco 7100 series router is composed of a two-part number in the format slot/port-number. The first number identifies the slot of the router in which the module is installed—slot 3 on the Cisco 7120 series routers and slot 4 on the Cisco 7140 series routers. The second number identifies the physical interface port number on the module.
Chapter 1 Overview Identifying Interface Addresses Interface Addresses of Cisco 7500 Series Routers with VIP The Cisco 7500 series routers accepts modules installed with a Versatile Interface Processor (VIP). The interface address of the modules is composed of a three-part number in the format slot/bay/port-number. The first number identifies the slot of the router in which the VIP is installed (slot 0 through 12, depending on the number of slots in the router).
C H A P T E R 2 Preparing for Installation This chapter describes the general equipment, safety, and site preparation requirements for installing the PA-FE-TX or PA-FE-FX port adapter.
Chapter 2 Preparing for Installation Minimum Software and Hardware Requirements Minimum Software and Hardware Requirements This section indicates the recommended minimum Cisco IOS software release required to use the PA-FE-TX and PA-FE-FX in supported platforms. For the latest releases supporting these port adapters, refer to the “Checking Hardware and Software Compatibility” section on page 2-3.
Chapter 2 Preparing for Installation Checking Hardware and Software Compatibility Checking Hardware and Software Compatibility To check the minimum software requirements of Cisco IOS software with the hardware installed on your router, Cisco maintains the Software Advisor tool on Cisco.com. This tool does not verify whether modules within a system are compatible, but it does provide the minimum IOS requirements for individual hardware modules or components.
Chapter 2 Preparing for Installation Safety Guidelines Waarschuwing BELANGRIJKE VEILIGHEIDSINSTRUCTIES Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen.
Chapter 2 Preparing for Installation Safety Guidelines Warnung WICHTIGE SICHERHEITSANWEISUNGEN Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer Körperverletzung führen könnte. Bevor Sie mit der Arbeit an irgendeinem Gerät beginnen, seien Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur Vermeidung von Unfällen bewusst.
Chapter 2 Preparing for Installation Safety Guidelines Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. O utilizador encontra-se numa situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha em atenção os perigos envolvidos no manuseamento de circuitos eléctricos e familiarize-se com as práticas habituais de prevenção de acidentes.
Chapter 2 Preparing for Installation Safety Guidelines Electrical Equipment Guidelines Follow these basic guidelines when working with any electrical equipment: • Before beginning any procedures requiring access to the chassis interior, locate the emergency power-off switch for the room in which you are working. • Disconnect all power and external cables before moving a chassis. • Do not work alone when potentially hazardous conditions exist.
Chapter 2 Preparing for Installation Laser/LED Safety Preventing Electrostatic Discharge Damage Electrostatic discharge (ESD) damage, which can occur when electronic cards or components are improperly handled, results in complete or intermittent failures. Port adapters and processor modules comprise printed circuit boards that are fixed in metal carriers. Electromagnetic interference (EMI) shielding and connectors are integral components of the carrier.
Chapter 2 Preparing for Installation FCC Class A Compliance Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. Warning Class 1 laser product. The multimode aperture contains a Class 1 LED warning label, as shown in Figure 2.
Chapter 2 Preparing for Installation FCC Class A Compliance Cisco PA-FE-TX and Cisco PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 2-10 OL-2899-02
C H A P T E R 3 Removing and Installing Port Adapters This chapter describes how to remove the PA-FE-TX and PA-FE-FX port adapters from supported platforms and also how to install a new or replacement port adapter.
Chapter 3 Removing and Installing Port Adapters Online Insertion and Removal Figure 3-1 Handling a Port Adapter Metal carrier H6420 Printed circuit board Online Insertion and Removal The Cisco 7100 series routers, Cisco 7200 series routers, Cisco 7200 VXR routers, Cisco uBR7246 router, Cisco 7301 routers, and the Cisco 7401ASR routers support the OIR of all module types. Therefore, you do not have to power down routers when removing and replacing modules in these chassis.
Chapter 3 Removing and Installing Port Adapters Port Adapter Removal and Installation Caution Warning When performing the following procedures, wear a grounding wrist strap to avoid ESD damage to the card. Some platforms have an ESD connector for attaching the wrist strap. Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when servicing.
Chapter 3 Removing and Installing Port Adapters Port Adapter Removal and Installation Catalyst 5000 Family Switches with RSM/VIP2—Removing and Installing a Port Adapter Note: You must first remove the Catalyst RSM/VIP2 from the chassis before removing a port adapter from the Catalyst RSM/VIP2. Step 1 To remove the port adapter, remove the screw that secures the port adapter (or blank port adapter). (See A.
Chapter 3 Removing and Installing Port Adapters Port Adapter Removal and Installation Cisco 7100 Series Routers—Removing and Installing a Port Adapter Step 1 To remove the port adapter, use a number 2 Phillips screwdriver to loosen the screws on the locking tab. Then slide the tab down to the unlocked position.
Chapter 3 Removing and Installing Port Adapters Port Adapter Removal and Installation Cisco 7200 Series Routers and Cisco 7200 VXR Routers—Removing and Installing a Port Adapter Step 1 Port adapter lever (locked position) To remove the port adapter, place the port adapter lever in the unlocked position. (See A.) The port adapter lever remains in the unlocked position.
Chapter 3 Removing and Installing Port Adapters Port Adapter Removal and Installation Cisco uBR7200 Series Routers—Removing a Port Adapter Step 1 To remove the port adapter, unlock the port adapter retaining mechanism. The port adapter lever remains in the unlocked position. Port adapters Port adapter lever (locked position) A Place the port adapter lever (Cisco uBR7223, see A), or the port adapter retention clip (Cisco uBR7246 and Cisco uBR7246 VXR, see B) in the unlocked position.
Chapter 3 Removing and Installing Port Adapters Port Adapter Removal and Installation Cisco uBR7200 Series Routers—Installing a Port Adapter Step 1 To insert the port adapter, carefully align the port adapter carrier between the upper and the lower edges of the port adapter slot. Metal carrier PC board 26524 Inside slot guide Step 2 Carefully slide the new port adapter halfway into the port adapter slot.
Chapter 3 Removing and Installing Port Adapters Port Adapter Removal and Installation Cisco 7301 Router—Removing and Installing a Port Adapter Step 1 Use an ESD wrist strap to ground yourself to the router. Step 2 To remove a port adapter, use a Phillips screwdriver to turn the screw holding the port adapter latch. The screw should be loose enough to allow the latch to rotate to an unlocked position. (See A.) The latch can rotate 360˚.
Chapter 3 Removing and Installing Port Adapters Port Adapter Removal and Installation Cisco 7401ASR Router—Removing and Installing a Port Adapter Step 1 To remove the port adapter, use a number 2 Phillips screwdriver to loosen the screw on the port adapter latch. Rotate the port adapter latch until it clears the faceplate of the port adapter. (See A.) The latch can rotate 360˚.
Chapter 3 Removing and Installing Port Adapters Port Adapter Removal and Installation Cisco 7000 Series Routers and Cisco 7500 Series Routers with VIP—Removing and Installing a Single-Width Port Adapter Note: You must first remove the VIP from the chassis before removing a port adapter from the VIP4. A Step 1 To remove the port adapter, remove the screw that secures the port adapter (or blank port adapter). (See A.
Chapter 3 Removing and Installing Port Adapters Connecting PA-FE-TX and PA-FE-FX Port Adapter Interface Cables Connecting PA-FE-TX and PA-FE-FX Port Adapter Interface Cables To continue your PA-FE-TX and PA-FE-FX port adapter installation, you must install the interface cables. The following instructions apply to all supported platforms. PA-FE-TX and PA-FE-FX Port Adapter RJ-45 and MII Connections On a single PA-FE, you can use either the RJ-45 (or SC for PA-FE-FX) connection or the MII connection.
Chapter 3 Removing and Installing Port Adapters Connecting PA-FE-TX and PA-FE-FX Port Adapter Interface Cables Figure 3-2 Connecting PA-FE-TX MII or RJ-45 Cables—Horizontal Orientation Shown Without Handles 0 H5920 FAST ETHERNET MII cable To transceiver, repeater, or DTE To repeater or DTE H6018 II M ER FAST ETHERNET 0 LIN K Connecting PA-FE-FX MII or SC Cables—Horizontal Orientation Shown Without Handles FIB Figure 3-3 RJ-45 cable or MII cable or Simplex (2) To repeater To transceiv
Chapter 3 Removing and Installing Port Adapters Connecting PA-FE-TX and PA-FE-FX Port Adapter Interface Cables The ferrite bead prevents electromagnetic interference (EMI) from affecting the PA-FE-TX-equipped system and is a required component for proper system operation.
C H A P T E R 4 Configuring the PA-FE-TX or PA-FE-FX To continue your PA-FE-TX or PA-FE-FX port adapter installation, you must configure the Fast Ethernet interface. The instructions that follow apply to all supported platforms. Minor differences between the platforms—with Cisco IOS software commands—are noted.
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Configuring the Interfaces Configuring the Interfaces After you verify that the new PA-FE-TX or PA-FE-FX is installed correctly (the enabled LED goes on), use the privileged-level configure command to configure the new interfaces.
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Configuring the Interfaces Step 2 The following examples explain how to configure the Fast Ethernet interface: • For the Cisco 7100 series, Cisco 7200 series, and the Cisco uBR7200 series, at the prompt specify the first interface to configure by entering the subcommand interface, followed by the type (fastethernet) and slot/interface (port adapter slot number and interface number).
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Configuring the Interfaces Configuring PA-FE-TX or PA-FE-FX Transmission Mode Half-duplex operation is the default transmission mode for the PA-FE-TX or PA-FE-FX. Use the full-duplex command to configure full-duplex operation for the PA-FE-TX or PA-FE-FX as follows: Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z.
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Checking the Configuration Router# show interface fastethernet 4/0 FastEthernet3/0/0 is administratively up, line protocol is up (display text omitted) Encapsulation ARPA, loopback not set, keepalive not set, hdx, MII (display text omitted) Use the media-type 100 command to return the media type for the PA-FE-TX or PA-FE-FX to the RJ-45 receptacle or SC receptacle.
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Checking the Configuration Using the show controllers Commands Display all the current interface processors and their interfaces using the show controllers command. Note The outputs that appear in this document may not match the output you receive when running these commands. The outputs in this document are examples only.
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Checking the Configuration Building configuration... Current configuration: ! ! ! user add admin uid 0 capability admin-access ! ! ! hostname CR4430 ! interface ethernet 0 ip address 10.2.2.8 255.255.255.0 ip broadcast-address 10.2.2.255 exit ! interface ethernet 1 exit ! ip default-gateway 10.2.2.1 ip name-server 10.2.2.6 ip route 0.0.0.0 0.0.0.0 10.2.2.
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Checking the Configuration match address 115 ! interface Ethernet0/0 ip address 98.98.98.1 255.255.255.0 no ip directed-broadcast ! interface Ethernet0/1 ip address 99.99.99.2 255.255.255.0 no ip directed-broadcast no ip route-cache no ip mroute-cache crypto map rtp ! interface Ethernet0/2 no ip address no ip directed-broadcast shutdown ! interface Ethernet0/3 no ip address no ip directed-broadcast shutdown ! ip classless ip route 0.0.0.0 0.0.0.0 99.99.99.
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Checking the Configuration • Cisco 7301 Routers—Example Output of the show version Command, page 4-11 • Cisco 7401ASR Routers—Example Output of the show version Command, page 4-11 • Cisco 7500 Series Routers with VIP—Example Output of the show version Command, page 4-12 Catalyst 5000 Family Switches with RSM/VIP2—Example Output of the show version Command Following is an example of the show version command from a Catalyst 5000 family switch: Router# sho
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Checking the Configuration 1 ISDN Basic Rate interface(s) 32K bytes of non-volatile configuration memory.
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Checking the Configuration X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. TN3270 Emulation software (copyright 1994 by TGV INC). Chassis Interface. 4 Ethernet/IEEE 802.3 interfaces. 2 FastEthernet/IEEE 802.3 interfaces. 4 Token Ring /IEEE802.5 interfaces. 12 Serial network interfaces. 1 Compression module. 125K bytes of non-volatile configuration memory. 1024K bytes of packet SRAM memory.
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Checking the Configuration System restarted by reload System image file is “slot0:c7401ASR-j-mz.960421”, booted via slot0 cisco 7401ASR (R4700) processor with 22528K/10240K bytes of memory. R4700 processor, Implementation 33, Revision 1.0 (Level 2 Cache) Last reset from power-on Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. Chassis Interface. 4 Ethernet/IEEE 802.3 interfaces. 2 FastEthernet/IEEE 802.3 interfaces.
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Checking the Configuration Using the show diag Command Display the types of port adapters installed in your system (and specific information about each) using the show diag slot command, where slot is the port adapter slot. Note The outputs that appear in this document may not match the output you receive when running these commands. The outputs in this document are examples only.
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Checking the Configuration Cisco 7000 Series Routers—Example Output of the show diag Command Following is an example of the show diag command from a Cisco 7000 router that shows two modules installed in slot 0 and slot 1 on a VIP2 in interface processor slot 3: Router# show diag 3 Slot 3: Physical slot 3, ~physical slot 0x7, logical slot 3, CBus 0 Microcode Status 0x4 Master Enable, LED, WCS Loaded Board is analyzed Pending I/O Status: None EEPROM format ver
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Checking the Configuration Cisco 7200 Series Routers, Cisco 7200 VXR Routers, and Cisco uBR7200 Series Routers—Example Output of the show diag Command Following is an example of the show diag slot command that shows a module in slot 1 of a Cisco 7200 series router: Router# show diag 1 Slot 1: Mueslix serial (RS232) module, 8 ports module is analyzed module insertion time 2d09h ago Hardware revision 255.
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Checking the Configuration Cisco 7401ASR Routers—Example Output of the show diag Command Following is an example of the show diag slot command that shows a port adapter in slot 1 of a Cisco 7401ASR router: Router# show diag 1 Slot 1: Fast-ethernet port adapter, 1 port Port adapter is analyzed Port adapter insertion time 2d09h ago Hardware revision 255.
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Checking the Configuration Using the show interfaces Command The show interfaces command displays status information (including the physical slot and interface address) for the interfaces you specify. For complete descriptions of interface commands and the configuration options available for specific interfaces, refer to the publications listed in the “Related Documentation” section on page viii.
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Checking the Configuration Cisco 7000 Series Routers—Example Output of the show interfaces Command Using the show interfaces type interface-processor-slot-number/module-slot-number/ interface-port-number command displays the status information about a specific type of interface —in this example, a FDDI interface—on a Cisco 7000 series router. Following is an example showing of the show interfaces command with a VIP2.
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Checking the Configuration Encapsulation HDLC, loopback not set, keepalive set (10 sec) [Additional display text omitted from this example] Router# show interfaces serial 3/2 Serial3/2 is up, line protocol is up Hardware is M8T-RS232 Internet address is 10.0.0.
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Checking the Configuration Cisco 7301 Routers—Example Output of the show interfaces Command Using the show interfaces type slot-number/interface-port-number command displays status information about a specific type of interface—in this example, GigE interfaces—on a Cisco 7301 router. Following is an example of the show interfaces command for a Cisco 7301 router. In this example, the three GigE interfaces (0 through 2) are on a module in slot 1.
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Checking the Configuration Cisco 7401ASR Routers—Example Output of the show interfaces Command Using the show interfaces type slot-number/interface-port-number command displays status information about a specific type of interface—in this example, ATM interfaces—on a Cisco 7401ASR router. Following is an example of the show interfaces command for a Cisco 7401ASR router. In this example, the eight ATM interfaces (0 through 7) are on a module in slot 1.
Chapter 4 Configuring the PA-FE-TX or PA-FE-FX Checking the Configuration Router# show interfaces serial 3/1/1 Serial3/1/1 is up, line protocol is up Hardware is cyBus Serial Internet address is 10.0.0.1 MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely 255/255, load 1/255 Encapsulation HDLC, loopback not set, keepalive not set [Additional display text omitted from this example] Router# show interfaces serial 3/1/2 Serial3/1/2 is up, line protocol is up Hardware is cyBus Serial Internet address is 10.0.
