Datasheet

203
Release Notes for Cisco IOS Release 12.1E on the Catalyst 6500 and Cisco 7600 Supervisor Engine and MSFC
OL-2310-11
Caveats
• Sessions to linecards will fail if you enter the ip telnet source-interface command and the specified
interface is an up/up state. This problem is resolved in Release 12.1(20)E. (CSCea36425)
• Layer 2 and Layer 3 switched counters remain at 0 after you enter the show interface vlan
command. This problem is resolved in Release 12.1(20)E. (CSCea69116)
• The stack-mib portname command for switchport-configured physical interfaces gets erased from
the startup configuration after a reboot. This problem is resolved in Release 12.1(20)E.
(CSCea83414)
• NetFlow v5 cannot be exported from a Catalyst 7600 series router through the POS interface. NDE
sends ARP requests for the NetFlow export destination. This problem is resolved in
Release 12.1(20)E. (CSCea83603)
• A Catalyst 6500 series switch cannot reliably ping the Gigabit Ethernet interface of another directly
connected Catalyst 6500 series switch when the same access list is applied to both the Gigabit
Ethernet and ATM FlexWAN interfaces. This problem is resolved in Release 12.1(20)E.
(CSCea86443)
• When you disconnect the cable between a WS-X6348-RJ-21V module and an IBM FE Open
Systems Adapter Express (OSA/E), and then reconnect the cable, the link does not come back up.
This problem is resolved in Release 12.1(20)E. (CSCea90470)
• A global command is needed for enabling link state messages on interfaces. This problem is resolved
in Release 12.1(20)E. (CSCeb06765)
• When Cisco IOS Server Load Balancing (SLB) is configured, the following message may be
generated when a Response Time Reporter (RTR) HTTP probe runs:
IDMGR-3-INVALID_ID: bad id in id_to_ptr
This problem is resolved in Release 12.1(20)E. (CSCeb19074)
• The ENTITY-MIB entPhysicalIsFRU displays “false” (2) for all field replaceable units. This problem is
resolved in Release 12.1(20)E. (CSCeb21058)
• If the TCAM is full and the entries are being switched by software, a Catalyst 6500 series switch or
Cisco 7600 series router may reload and display the following error message:
%SYS-SP-2-WATCHDOG: Process aborted on watchdog timeout, process = FIB Control Task
This problem is resolved in Release 12.1(20)E. (CSCeb36253)
• On a system with redundant Supervisor Engines running Cisco IOS Release 12.1(19)E that is
functioning as an external router to a Cisco 5000 series switch, FCP messages similar to this may
be displayed:
FCP: shortcut ack msg for different router XXXX.XXXX.XXXX
These messages are informational only. This problem is resolved in Release 12.1(20)E.
(CSCeb44823)
• The system resets when the AAA protocol is configured for accounting. This problem is resolved in
Release 12.1(20)E. (CSCeb42177)
• The following message might be followed by a reload:
%ALIGN-1-FATAL: Corrupted program counter pc=0xX, ra=0xXXXXXXXX, sp=0xXXXXXXXX
This problem is resolved in Release 12.1(20)E. (CSCeb48670)
• When you enter the show policy-map interface [interface] command on a system with a Supervisor
Engine 2 and MSFC2, a system reload may occur. This problem is resolved in Release 12.1(20)E.
(CSCeb49634)