Installation guide
Table Of Contents
- Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)
- Contents
- Introduction
- Components Supported
- MDS 9000 Chassis and Module Support
- Software Download Process
- Determining the Software Version
- Determining Software Version Compatibility
- Downloading Software
- Selecting the Correct Software Image for an MDS 9100 Series Switch
- Selecting the Correct Software Image for an MDS 9200 Series Switch
- Selecting the Correct Software Image for an MDS 9500 Series Switch
- NPE Software Images
- Upgrading Your Cisco MDS NX-OS Software Image
- Downgrading Your Cisco MDS SAN-OS Software Image
- New Features in Cisco MDS NX-OS Release 5.2
- New Features in Cisco MDS NX-OS Release 5.2(8c)
- Cisco MDS NX-OS Release 5.2(8c) is a maintenance release that includes bug fixes. It does not include new features.
- New Features in Cisco MDS NX-OS Release 5.2(8b)
- New Features in Cisco MDS NX-OS Release 5.2(8a)
- New Features in Cisco MDS NX-OS Release 5.2(8)
- New Features in Cisco MDS NX-OS Release 5.2(6b)
- New Features in Cisco MDS NX-OS Release 5.2(6a)
- New Features in Cisco MDS NX-OS Release 5.2(6)
- New Features in Cisco MDS NX-OS Release 5.2(2d)
- New Features in Cisco MDS NX-OS Release 5.2(2a)
- New Features in Cisco MDS NX-OS Release 5.2(2)
- New Features in Cisco MDS NX-OS Release 5.2(1)
- New Hardware in Cisco MDS NX-OS Release 5.2(1)
- Licensed Cisco NX-OS Software Packages
- Deprecated Features
- Limitations and Restrictions
- SME Quorum
- OUI Mismatch for SME Tape Targets
- FCIP Performance Drop
- FCoE Module
- IPv6
- User Roles
- Schedule Job Configurations
- Maximum Number of Zones Supported in Interop Mode 4
- InterVSAN Routing
- Java Web Start
- VRRP Availability
- Using a RSA Version 1 Key for SSH Following an Upgrade
- CFS Cannot Distribute All Call Home Information
- Availability of F Port Trunking and F Port Channels
- Reserved VSAN Range and Isolated VSAN Range Guidelines
- Applying Zone Configurations to VSAN 1
- Running Storage Applications on the MSM-18/4
- RSPAN Traffic Not Supported on CTS Ports on 8-Gbps Switching Modules
- I/O Accelerator Feature Limitations
- Support for FCIP Compression Modes
- Saving Copies of the Running Kickstart and System Images
- Configuring Buffer Credits on a Generation 2 or Generation 3 Module
- Features Not Supported on the Cisco MDS 9148 Switch
- PPRC Not Supported with FCIP Write Acceleration
- Configuring a Persistent FCID in an IVR Configuration with Brocade Switches
- Caveats
- Related Documentation
- Obtaining Documentation and Submitting a Service Request
44
Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)
OL-27554-07
Caveats
Symptom: Some Fibre Channel Routing (FCR) peers might get out of sync with the master switch
FCR peer after an Inter-Switch Link (ISL) flap. This might cause the intelligent application flows
not to come online or to get deleted.
Workaround: This issue might occur when using any of the following FCR intelligent applications:
–
Storage Media Encryption (SME)
–
I/O Acceleration (IOA)
–
Data Mobility Manager (DMM)
Workaround: Check the intelligent applications to verify whether any flows are deleted on the
problematic switch. If they did, you must recreate flows again through the application CLI or the
Cisco Fabric Manager or Cisco Data Center Network Manager (DCNM)-SAN interface.
Enter the following supervisor CLI commands on the problematic FCR switch that triggers it to
resync its configuration with the rest of the fabric.
For a single switch, use the following command:
test fc-redirect config sync-with-fabric
If more than one peer is affected by this issue, use the following command:
test fc-redirect config sync-with-fabric all-peers
• CSCtr50223
Symptom: On the MDS 9513 switch, when an MSM-18/4 module boots up, it sends a request to the
supervisor module to mount the modflash on the MSM-18/4 module. If there is a timeout or error in
response, the following syslog message displays:
2011 Jul 14 01:18:13 sw-dc5-br2-12 %LC_MNT_MGR-SLOT3-2-LC_MNT_MGR_ERROR: SUP mount
failed. MTS receive timedout
2011 Jul 14 01:19:06 sw-dc5-br2-12 %PROC_MGR-SLOT3-2-ERR_MSG: ERROR: PID 1144
(lc_mnt_mgr) exited abnormally, exit status (0xa)
2011 Jul 14 01:19:06 sw-dc5-br2-12 %MODULE-2-MOD_MINORSWFAIL: Module 3 (serial:
JAE1141ZB43) reported a failure in service lc_mnt_mgr
This issue might be seen when the supervisor module is unusually busy and cannot process the
mount request from the MSM-18/4 module, or the actual mount command on the supervisor takes a
long time.
Workaround: Reload the MSM-18/4 module in the same slot/module where the modflash mount
failed. A request will be sent to the supervisor to mount the modflash.
• CSCty82821
Symptom: After creating an SME cluster, adding disks to a disk group, changing some disk states,
and starting the master key rekey, the key creation date is invalid.
Workaround: None.