Datasheet
Table Of Contents
- Regulatory Compliance and Safety Information for the Cisco Secure ACS Solution Engine Release 4.0
- Documentation Road Map
- General Precautions
- Maintaining Safety with Electricity
- Preparing Your Site for Installation
- Regulatory Standards Compliance
- Safety Information
- Statement 1-Power Disconnection Warning
- Statement 12-Power Supply Disconnection Warning
- Statement 19-TN Power Warning
- Statement 22-SELV Circuit Warning
- Statement 88-Service Personnel Warning
- Statement 106-More Than One Power Cord
- Statement 117-Safety Cover Requirement
- Statement 119-Unit Short Circuit Protection
- Statement 12-Power Supply Disconnection Warning
- Statement 331-Power Supply Installation Warning
- Statement 1001-Work During Lightning Activity
- Statement 1004-Installation Instructions
- Statement 1005-Circuit Breaker
- Statement 1006-Chassis Warning for Rack-Mounting and Servicing
- Statement 1015-Battery Handling
- Statement 1041-Disconnecting Telephone-Network Cables
- Statement 1064-Grounded Equipment
- Statement 1074-Comply with Local and National Electrical Codes
- Statement 1017-Restricted Area
- Statement 1019-Main Disconnecting Device
- Statement 1021-SELV Circuit
- Statement 1024-Ground Conductor
- Statement 1028-More Than One Power Supply
- Statement 1029-Blank Faceplates and Cover Panels
- Statement 1030-Equipment Installation
- Statement 1040-Product Disposal
- Obtaining Documentation
- Documentation Feedback
- Cisco Product Security Overview
- Obtaining Technical Assistance
- Obtaining Additional Publications and Information

35
Regulatory Compliance and Safety Information for the Cisco Secure ACS Solution Engine Release 4.0
78-17259-02
Safety Information
Statement 1006—Chassis Warning for Rack-Mounting and
Servicing
Warning
To prevent bodily injury when mounting or servicing this unit in a rack, you
must take special precautions to ensure that the system remains stable. The
following guidelines are provided to ensure your safety:
• This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
• When mounting this unit in a partially filled rack, load the rack from the bottom to the
top with the heaviest component at the bottom of the rack.
• If the rack is provided with stabilizing devices, install the stabilizers before mounting
or servicing the unit in the rack.
Waarschuwing
Om lichamelijk letsel te voorkomen wanneer u dit toestel in een rek monteert
of het daar een servicebeurt geeft, moet u speciale voorzorgsmaatregelen
nemen om ervoor te zorgen dat het toestel stabiel blijft. De onderstaande
richtlijnen worden verstrekt om uw veiligheid te verzekeren:
• Dit toestel dient onderaan in het rek gemonteerd te worden als het toestel het enige
in het rek is.
• Wanneer u dit toestel in een gedeeltelijk gevuld rek monteert, dient u het rek van
onderen naar boven te laden met het zwaarste onderdeel onderaan in het rek.
• Als het rek voorzien is van stabiliseringshulpmiddelen, dient u de stabilisatoren te
monteren voordat u het toestel in het rek monteert of het daar een servicebeurt geeft.
Varoitus
Kun laite asetetaan telineeseen tai huolletaan sen ollessa telineessä, on
noudatettava erityisiä varotoimia järjestelmän vakavuuden säilyttämiseksi,
jotta vältytään loukkaantumiselta. Noudata seuraavia turvallisuusohjeita:
• Jos telineessä ei ole muita laitteita, aseta laite telineen alaosaan.
• Jos laite asetetaan osaksi täytettyyn telineeseen, aloita kuormittaminen sen
alaosasta kaikkein raskaimmalla esineellä ja siirry sitten sen yläosaan.
• Jos telinettä varten on vakaimet, asenna ne ennen laitteen asettamista telineeseen
tai sen huoltamista siinä.










