Wall Mounts • Wall Mount Kits, on page 1 • Non-Lockable Wall Mount Components for 7811, on page 2 • Non-Lockable Wall Mount Components, on page 9 • Non-Lockable Wall Mount Components for 7861, on page 17 • Adjust the Handset Rest, on page 25 Wall Mount Kits Each wall mount is unique to your phone model and cannot be used for another phone. If you are planning to attach your phone to a wall, purchase the wall mount kit specific to your phone.
Wall Mounts Non-Lockable Wall Mount Components for 7811 Non-Lockable Wall Mount Components for 7811 The following figure shows the components of the Cisco IP Phone 7811 Wall Mount Kit. Figure 1: Wall Mount Kit Components for 7811 The package includes these items: • One phone bracket • One wall bracket • Four M4 x 25-mm Phillips-head screws with four anchors • Two M3 x 7-mm Self-tapping screws • One 200-mm Ethernet cable This section describes how to install and remove the ADA nonlockable wall mount kit.
Wall Mounts Install the Non-Lockable Wall Mount Kit for 7811 Figure 3: Side View of ADA Non-Lockable Wall Mount Kit Installed on Phone Install the Non-Lockable Wall Mount Kit for 7811 The wall mount kit can be mounted on most surfaces, including concrete, brick, and similar hard surfaces. To mount the kit on concrete, brick, or similar hard surfaces, you must provide the appropriate screws and anchors for your wall surface.
Wall Mounts Install the Non-Lockable Wall Mount Kit for 7811 Figure 4: Bracket Installation Step 2 Attach the phone bracket to the IP Phone. a) Detach the power cord and other attached cords from the base of the phone, except the handset cord (and headset cord, if there is a headset). b) Attach the phone bracket by inserting the tabs into the mounting tabs on the back of the phone. The phone ports should be accessible through the holes in the bracket.
Wall Mounts Install the Non-Lockable Wall Mount Kit for 7811 Figure 5: Phone Bracket Attachment 1 Step 3 Screw holes Attach the cables to the phone: a) Attach the Ethernet cable to the 10/100/1000 SW network port and wall jack. b) (Optional) If you are connecting a network device (such as a computer) to the phone, attach the cable to the 10/100/1000 Computer (PC access) port. c) (Optional) If you use an external power supply, plug the power cord into the phone.
Wall Mounts Install the Non-Lockable Wall Mount Kit for 7811 Figure 6: Cable Attachment Step 4 1 Phone Bracket 4 Handset Port 2 Network Port 5 AC Adapter Port 3 Wall Bracket 6 Optional Power Cable Attach the phone to the wall bracket by inserting the tabs on the top of the wall bracket into the slots on the phone bracket.
Wall Mounts Remove the Phone from the Non-Lockable Wall Mount for 7811 Figure 7: Phone to Wall Bracket Attachment Step 5 Press the phone firmly into the wall bracket and slide the phone down. The tabs in the bracket click into position. Step 6 Proceed to Adjust the Handset Rest, on page 25. Remove the Phone from the Non-Lockable Wall Mount for 7811 The wall mounting plate contains two tabs to lock the plate into the phone bracket. The following figure shows the location and shape of the tabs.
Wall Mounts Remove the Phone from the Non-Lockable Wall Mount for 7811 Figure 8: Tab Location To remove the phone and mounting plate from the wall bracket, you must disengage these tabs. Before you begin You require two screwdrivers or metal rods. Procedure Step 1 Push the screwdrivers into the left and right holes in the phone mounting plate approximately 1 in. (2.5 cm). Step 2 Lift the screwdriver handles up to push down on the tabs.
Wall Mounts Non-Lockable Wall Mount Components Figure 9: Disengage Tabs Step 3 Press firmly to disengage the tabs and move the phone up at the same time to release the phone from the wall bracket. Non-Lockable Wall Mount Components The following figure shows the components of the Cisco IP Phone 7800 Series Wall Mount Kit. Figure 10: Wall Mount Kit Components The package includes these items: • One phone bracket • One wall bracket • Four M8-18 x 1.
Wall Mounts Non-Lockable Wall Mount Components • Two M2.5 x 6-mm machine screws • One 6-inch Ethernet cable This section describes how to install and remove the ADA nonlockable wall mount kit.
Wall Mounts Install the Non-Lockable Wall Mount Kit Install the Non-Lockable Wall Mount Kit The wall mount kit can be mounted on most surfaces, including concrete, brick, and similar hard surfaces. To mount the kit on concrete, brick, or similar hard surfaces, you must provide the appropriate screws and anchors for your wall surface.
Wall Mounts Install the Non-Lockable Wall Mount Kit Figure 13: Bracket Installation Step 2 Attach the phone bracket to the IP Phone. a) Detach the power cord and other attached cords from the base of the phone, except the handset cord (and headset cord, if there is a headset). b) Remove the label covers that conceal the screw holes. Note Cisco IP Phone 7811 does not have label covers. c) Attach the phone bracket by inserting the tabs into the mounting tabs on the back of the phone.
Wall Mounts Install the Non-Lockable Wall Mount Kit Figure 14: Phone Bracket Attachment 1 Step 3 Screw holes 2 Slots for mounting tabs Attach the cables to the phone: a) Attach the Ethernet cable to the 10/100/1000 SW network port and wall jack. b) (Optional) If you are connecting a network device (such as a computer) to the phone, attach the cable to the 10/100/1000 Computer (PC access) port. c) (Optional) If you use an external power supply, plug the power cord into the phone.
Wall Mounts Install the Non-Lockable Wall Mount Kit Figure 15: Cable Attachment Step 4 1 Phone Bracket 4 Handset Port 2 Network Port 5 AC Adapter Port 3 Wall Bracket 6 Optional Power Cable Attach the phone to the wall bracket by inserting the tabs on the top of the wall bracket into the slots on the phone bracket.
Wall Mounts Remove the Phone from the Non-Lockable Wall Mount Figure 16: Phone to Wall Bracket Attachment Step 5 Press the phone firmly into the wall bracket and slide the phone down. The tabs in the bracket click into position. Step 6 Proceed to Adjust the Handset Rest, on page 25. Remove the Phone from the Non-Lockable Wall Mount The phone mounting plate contains two tabs to lock the plate into the wall bracket. The following figure shows the location and shape of the tabs.
Wall Mounts Remove the Phone from the Non-Lockable Wall Mount Figure 17: Tab Location To remove the phone and mounting plate from the wall bracket, you must disengage these tabs. Before you begin You require two screwdrivers or metal rods. Procedure Step 1 Push the screwdrivers into the left and right holes in the phone mounting plate approximately 1 in. (2.5 cm). Step 2 Lift the screwdriver handles up to push down on the tabs.
Wall Mounts Non-Lockable Wall Mount Components for 7861 Figure 18: Disengage Tabs Step 3 Press firmly to disengage the tabs and move the phone up at the same time to release the phone from the wall bracket. Non-Lockable Wall Mount Components for 7861 The following figure shows the components of the Cisco IP Phone 7861 Wall Mount Kit.
Wall Mounts Non-Lockable Wall Mount Components for 7861 • Four M4 x 25-mm Phillips-head screws with four anchors • Two M3 x 7-mm Self-tapping screws • One 200-mm Ethernet cable This section describes how to install and remove the ADA nonlockable wall mount kit.
Wall Mounts Install the Non-Lockable Wall Mount Kit for 7861 Figure 21: Side View of ADA Non-Lockable Wall Mount Kit Installed on Phone Install the Non-Lockable Wall Mount Kit for 7861 The wall mount kit can be mounted on most surfaces, including concrete, brick, and similar hard surfaces. To mount the kit on concrete, brick, or similar hard surfaces, you must provide the appropriate screws and anchors for your wall surface.
Wall Mounts Install the Non-Lockable Wall Mount Kit for 7861 a) Hold the bracket on the wall and place it so that the arrow on the back of the bracket points up. b) Use the level to ensure that the bracket is level and use a pencil to mark the screw holes. c) Using a #2 Phillips-head screwdriver, carefully center the anchor over the pencil mark and press the anchor into the wall. d) Screw the anchor clockwise into the wall until it is seated flush.
Wall Mounts Install the Non-Lockable Wall Mount Kit for 7861 Figure 23: Phone Bracket Attachment Step 3 1 Screw holes 2 Slot for Mounting Tabs Attach the cables to the phone: a) Attach the Ethernet cable to the 10/100/1000 SW network port and wall jack. b) (Optional) If you are connecting a network device (such as a computer) to the phone, attach the cable to the 10/100/1000 Computer (PC access) port. c) (Optional) If you use an external power supply, plug the power cord into the phone.
Wall Mounts Install the Non-Lockable Wall Mount Kit for 7861 Figure 24: Cable Attachment Step 4 1 Phone Bracket 4 Handset Port 2 Network Port 5 AC Adapter Port 3 Wall Bracket 6 Optional Power Cable Attach the phone to the wall bracket by inserting the tabs on the top of the wall bracket into the slots on the phone bracket.
Wall Mounts Remove the Phone from the Non-Lockable Wall Mount Figure 25: Phone to Wall Bracket Attachment Step 5 Press the phone firmly into the wall bracket and slide the phone down. The tabs in the bracket click into position. Step 6 Proceed to Adjust the Handset Rest, on page 25. Remove the Phone from the Non-Lockable Wall Mount The wall mounting plate contains two tabs to lock the plate into the phone bracket. The following figure shows the location and shape of the tabs.
Wall Mounts Remove the Phone from the Non-Lockable Wall Mount Figure 26: Tab Location To remove the phone and mounting plate from the wall bracket, you must disengage these tabs. Before you begin You require two screwdrivers or metal rods. Procedure Step 1 Push the screwdrivers into the left and right holes in the phone mounting plate approximately 1 in. (2.5 cm). Step 2 Lift the screwdriver handles up to push down on the tabs.
Wall Mounts Adjust the Handset Rest Figure 27: Disengage Tabs Step 3 Press firmly to disengage the tabs and move the phone up at the same time to release the phone from the wall bracket. Adjust the Handset Rest If your phone is wall-mounted or if the handset slips out of the cradle too easily, you may need to adjust the handset rest to ensure that the receiver does not slip out of the cradle.
Wall Mounts Adjust the Handset Rest Procedure Step 1 Remove the handset from the cradle and pull the plastic tab from the handset rest. Step 2 Rotate the tab 180 degrees. Step 3 Hold the tab between two fingers, with the corner notches facing you. Step 4 Line up the tab with the slot in the cradle and press the tab evenly into the slot. An extension protrudes from the top of the rotated tab. Step 5 Return the handset to the handset rest.
