Technical References

D14642.13 Codec C40-C60 API Reference Guide TC6.3, NOVEMBER 2013. Copyright © 2010–2013 Cisco Systems, Inc. All rights reserved. 75
Cisco TelePresence System Codec C40/C60 API Reference Guide
xConfiguration Video Selfview
Determine if the main video source (self view) shall be displayed on screen.
This setting is obsoleted by the Video SelfviewDefault Mode setting as from TC6.0.
Requires user role: USER
Value space: <Off/On>
Off: Do not display self view on screen.
On: Display self view on screen.
Example:
xConfiguration Video Selfview: On
xConfiguration Video SelfviewPosition
Select where the small self view PiP (Picture-in-Picture) will appear on screen.
This setting is obsoleted by the Video SelfviewDefault PIPPosition setting as from TC6.0.
Requires user role: ADMIN
Value space: <UpperLeft/UpperCenter/UpperRight/CenterLeft/CenterRight/LowerLeft/LowerRight>
UpperLeft: The self view PiP will appear in the upper left corner of the screen.
UpperCenter: The self view PiP will appear in the upper center of the screen.
UpperRight: The self view PiP will appear in the upper right corner of the screen.
CenterLeft: The self view PiP will appear on the left side of the screen, in center.
CenterRight: The self view PiP will appear on the right side of the screen, in center.
LowerLeft: The self view PiP will appear in the lower left corner of the screen.
LowerRight: The self view PiP will appear in the lower right corner of the screen.
Example:
xConfiguration Video SelfviewPosition: LowerRight
xConfiguration Video SelfviewControl AutoResizing
The size of the self view frame can be configured to automatically change according to the following
rules. The size is reduced from full screen to PiP (picture-in-picture) when there is a change in a
frame that overlaps with the self view frame. The size is increased from PiP to full screen when
nothing else is displayed on the monitor. The last rule does not apply to monitors with MonitorRole
set to First.
Requires user role: ADMIN
Value space: <Off/On>
Off: Self view will not be automatically resized.
On: Self view is automatically resized as described above.
Example:
xConfiguration Video SelfviewControl AutoResizing: On
xConfiguration Video SelfviewDefault Mode
Determine if the main video source (self view) shall be displayed on screen after a call. The position
and size of the self view window is determined by the Video SelfviewDefault PIPPosition and the
Video Selfview FullscreenMode settings respectively.
This setting obsoletes the Video Selfview setting as from TC6.0.
Requires user role: ADMIN
Value space: <Off/Current/On>
Off: Self view is switched off when leaving a call.
Current: Self view is left as is, i.e. if it was on during the call, it remains on after the call; if it was off
during the call, it remains off after the call.
On: Self view is switched on when leaving a call.
Example:
xConfiguration Video SelfviewDefault Mode: Current
xConfiguration Video SelfviewDefault FullscreenMode
Determine if the main video source (self view) shall be shown in full screen or as a small picture-in-
picture (PiP) after a call. The setting only takes effect when self view is switched on (see the Video
SelfviewDefault Mode setting).
Requires user role: ADMIN
Value space: <Off/Current/On>
Off: Self view will be shown as a PiP.
Current: The size of the self view picture will be kept unchanged when leaving a call, i.e. if it was
a PiP during the call, it remains a PiP after the call; if it was fullscreen during the call, it remains
fullscreen after the call.
On: The self view picture will be shown in fullscreen.
Example:
xConfiguration Video SelfviewDefault FullscreenMode: Current
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatus
xConfigu ration