Troubleshooting Guide

ManualsBrandsCisco ManualsIP phonesCisco Emergency Responder 11.5

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 1 of 73

EDCS#607132 Rev # Initial Version

Application Note

NEC IPX2400 Release 15 using T1 QSIG to Cisco Unified

Communications Manager 6.0 and Cisco Emergency Responder

2.0

Cisco Confidential

This document contains valuable trade secrets and confidential information belonging to Cisco Systems, Inc. and its suppliers. The aforementioned shall not be disclosed to any person,

organization, or entity, unless such disclosure is subject to the provisions of a written non-disclosure and proprietary rights agreement, or intellectual property license agreement,

approved by Cisco Systems, Inc. The distribution of this document does not grant any license or rights, in whole or in part, to its content, the product(s), the technology(ies), or

intellectual property, described herein.

Disclaimer

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS DOCUMENT ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,

INFORMATION, AND RECOMMENDATIONS IN THIS DOCUMENT ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,

EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE CUSTOMER ASSUMES ALL RESPONSIBILITY FOR PROPERLY CONFIGURING THE CISCO EMERGENCY RESPONDER. CISCO HEREBY DISCLAIMS ANY AND

ALL LIABILITY ARISING FROM OR IN CONNECTION WITH A USERS INABILITY TO REACH EMERGENCY SERVICE RESPONDERS (INCLUDING INABILITY TO

ACCESS A PUBLIC SAFETY ANSWERING POINT) OR THE INABILITY OF EMERGENCY SERVICE RESPONDERS TO IDENTIFY A USERS LOCATION. CISCO

STRONGLY RECOMMENDS THAT ALL CUSTOMERS VERIFY AND TEST CONFIGURATION OF THE CISCO EMERGENCY RESPONDER IMMEDIATELY FOLLOWING

INITIAL CONFIGURATION AND ON A PERIODIC BASIS THEREAFTER. CISCO FURTHER RECOMMENDS THAT ALL CUSTOMERS PROVIDE ADEQUATE TRUNK

AND BANDWIDTH CAPACITY TO ENSURE THAT AUDIO PATHS ARE AVAILABLE FOR EMERGENCY CALLS.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,

WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS PRODUCT, EVEN IF CISCO OR

ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

July 11, 2007 Initial version

Table of Contents

Introduction ..............................................................................................................................................................................................................2

Network Topology....................................................................................................................................................................................................2

Limitations................................................................................................................................................................................................................2

System Components .................................................................................................................................................................................................3

Hardware Requirements......................................................................................................................................................................................3

Software Requirements .......................................................................................................................................................................................3

Features ....................................................................................................................................................................................................................3

Features Supported..............................................................................................................................................................................................3

Configuration............................................................................................................................................................................................................4

Configuring Cisco Unified Communications Manager .......................................................................................................................................4

Configuring Cisco Emergency Responder ........................................................................................................................................................42

Configuring the NEC IPX2400 PBX.................................................................................................................................................................68

Acronyms ...............................................................................................................................................................................................................71

Summary of content (73 pages)

PAGE 1
Application Note NEC IPX2400 Release 15 using T1 QSIG to Cisco Unified Communications Manager 6.0 and Cisco Emergency Responder 2.0 Cisco Confidential This document contains valuable trade secrets and confidential information belonging to Cisco Systems, Inc. and its suppliers.
PAGE 2
Introduction The following is an Application Note for E911 Interoperability of a Cisco Unified Communications Manager 6.0 and Cisco Emergency Responder 2.0 to a NEC IPX2400 PBX via a Cisco Media Module CMM T1-QSIG trunk. The CUCM system is connected to a simulated E911 PSAP (Public Safety Answering Point) via a Cisco 3845 w/ CAMA trunk registered using H323.
PAGE 3
System Components Hardware Requirements Cisco Hardware Cisco 3825 Gateway with NM-HD-V2/VIC2-4FXO (CAMA trunk) Cisco Cat6K switch Cisco Unified Communications Manager server Cisco Emergency Responder server Cisco WS-SVC-CMM-6T1 Communications Media Module (inserted into cat6K) NEC IPX2400 Software Requirements Cisco IOS Software release “c3825-ipvoice-mz.124-11.T” Cisco IOS Software release “wscmm-ipvoicek9-mz.124-11.T PBX Software: Version Release 15 Cisco Unified Communications Manager 6.
PAGE 4
Configuration Configuring Cisco Unified Communications Manager Partitions © 2007 Cisco Systems, Inc. All right reserved. Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.
PAGE 24
Note: A Backup CER server was not used during testing therefore CTI route point for 912 was not created. © 2007 Cisco Systems, Inc. All right reserved. Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.
PAGE 41
Route Pattern to QSIG Trunk Note: For detailed information regarding QSIG interoperability between CCM and NEC PBX go to: http://www.cisco.com/warp/public/779/largeent/avvid/inter_operability/flash/portal.html SNMP service must be active © 2007 Cisco Systems, Inc. All right reserved. Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.
PAGE 42
Configuring Cisco Emergency Responder Cisco Unified Communications Manager Details © 2007 Cisco Systems, Inc. All right reserved. Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.
PAGE 55
Configuring the Cisco CMM IOS Gateway MGCP for QSIG connectivity tonycmm#sh run Building configuration... Current configuration : 2077 bytes ! version 12.4 © 2007 Cisco Systems, Inc. All right reserved. Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.
PAGE 56
no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname tonycmm ! boot-start-marker boot system bootflash:wscmm-ipvoicek9-mz.124-11.T.bin boot-end-marker ! logging buffered 10000000 no logging console enable password cisco ! no aaa new-model mmi polling-interval 60 no mmi auto-configure no mmi pvc mmi snmp-timeout 180 ! ! no ip domain lookup ip host CM-BARZA 172.20.110.
PAGE 57
! ! ! ! ! ! controller T1 1/0 pri-group timeslots 1-24 service mgcp ! controller T1 1/1 ! controller T1 1/2 ! controller T1 1/3 ! controller T1 1/4 ! controller T1 1/5 ! ! ! ! interface GigabitEthernet1/0 ip address 172.20.8.253 255.255.255.
PAGE 58
no cdp enable ! ip default-gateway 172.20.8.1 ip route 0.0.0.0 0.0.0.0 172.20.8.1 ! no ip http server no ip http secure-server ! ! control-plane ! ! voice-port 1/0:23 ! ccm-manager mgcp ccm-manager music-on-hold ccm-manager config server CM-BARZA ccm-manager config ! mgcp mgcp call-agent CM-BARZA 2427 service-type mgcp version 0.
PAGE 59
! ! ! ! line con 0 password cisco transport output all line vty 0 4 exec-timeout 0 0 password cisco login transport input all transport output all ! ! end tonycmm# Cisco 3825 IOS Gateway H323 configuration for CAMA trunk connectivity CAMA_GW#sh run Building configuration... Current configuration : 1241 bytes ! version 12.
PAGE 60
enable password cisco ! no aaa new-model ip cef ! ! ! ! multilink bundle-name authenticated ! voice-card 0 no dspfarm ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! © 2007 Cisco Systems, Inc. All right reserved. Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.
PAGE 61
! interface GigabitEthernet0/0 ip address 172.20.8.26 255.255.255.0 duplex auto speed auto media-type rj45 no keepalive ! interface GigabitEthernet0/1 no ip address shutdown duplex auto speed auto media-type rj45 no keepalive ! ip route 0.0.0.0 0.0.0.0 172.20.8.1 ! ! ip http server no ip http secure-server ! ! ! ! control-plane ! ! ! voice-port 0/2/0 signal cama KP-0-NPA-NXX-XXXX-ST dial-type mf timing hookflash-out 500 description CAMA ! voice-port 0/2/1 © 2007 Cisco Systems, Inc. All right reserved.
PAGE 62
! voice-port 0/3/0 ! voice-port 0/3/1 ! ! ! ! ! dial-peer voice 911 pots destination-pattern 911 no digit-strip port 0/2/0 forward-digits all ! dial-peer voice 999 voip description Call-in PSTN simulation destination-pattern .T session target ipv4:172.20.110.254 ! ! ! line con 0 password cisco login stopbits 1 line aux 0 stopbits 1 line vty 0 4 password cisco login ! scheduler allocate 20000 1000 ! end © 2007 Cisco Systems, Inc. All right reserved.
PAGE 64
CAMA voice-port config CAMA_GW#sh voice port 0/2/0 Foreign Exchange Office 0/2/0 Slot is 0, Sub-unit is 2, Port is 0 Type of VoicePort is FXO Operation State is DORMANT Administrative State is UP The Last Interface Down Failure Cause is Administrative Shutdown Description is CAMA Noise Regeneration is enabled Non Linear Processing is enabled Non Linear Mute is disabled Non Linear Threshold is -21 dB Music On Hold Threshold is Set to -38 dBm In Gain is Set to 0 dB Out Attenuation is Set to 3 dB Echo Cancell
PAGE 65
Interdigit Time Out is set to 10 s Call Disconnect Time Out is set to 60 s Ringing Time Out is set to 180 s Wait Release Time Out is set to 30 s Companding Type is u-law Region Tone is set for US Analog Info Follows: Currently processing none Maintenance Mode Set to None (not in mtc mode) Number of signaling protocol errors are 0 Impedance is set to 600r Ohm Station name None, Station number None Translation profile (Incoming): Translation profile (Outgoing): Voice card specific Info Follows: Signal Type
PAGE 66
InterDigit Duration Timing is set to 65 ms Pulse Rate Timing is set to 10 pulses/second InterDigit Pulse Duration Timing is set to 750 ms Percent Break of Pulse is 60 percent GuardOut timer is 2000 ms Minimum ring duration timer is 125 ms Hookflash-in Timing is set to 600 ms Hookflash-out Timing is set to 500 ms Supervisory Disconnnct Timing is set to 350 ms OPX Ring Wait Timing is set to 6000 ms CAMA_GW# CAT6k configuration Console> (enable) sh snmp SNMP: Enabled RMON: Disabled Extended RMON Netflow E
PAGE 67
Message Interval : 60 Hold Time Version : 180 : V2 Device Id Format : Other Console> (enable) set interface sc0 109 172.20.8.20/255.255.255.0 172.20.8.255 © 2007 Cisco Systems, Inc. All right reserved. Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.
PAGE 68
Configuring the NEC IPX2400 PBX The NEC requires a substantial amount of programming and circuit card switch settings to properly install T1 PRI. It is beyond the scope of this document to provide the entire configuration, therefore the NEC information below is directed to NEC techs The switch settings and software references in this document assume a familiarity with the NEC 2400. It is highly recommended to have a NEC ISDN certified technician setup the NEC portion.
PAGE 69
8 1 2 SW4 Fixed On Fixed Off (Protocol Selection) ON = User OFF = Network Dch Signal Logic Dch Speed Selection Dch Speed Selection Fixed On Fixed On Fixed On PAD PAD PAD PAD PAD PAD PAD Idle Code 3 4 5 6 7 8 1 2 3 4 5 6 7 8 SW5 ON OFF ON OFF ON ON ON ON ON ON ON ON ON ON ON ON OFF Route (ARTD) Configuration [IPX-R15_IP::LRTD] January 27,2006 * Route Class Data List * Starting RT RT CDN 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029
PAGE 70
033 034 035 036 037 038 039 040 041 042 RT CDN 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 HD GUARD WINK VAD CLD FA BC TCM TDMQ TRSC 0 1 0 0 0 0 0 0 0 0 075 076 077 078 079 080 081 082 083 084 STC MC2 MT TONE PPTM MPTM LPTM RSAX CST CSEG 0 0 0 0 0 0 0 0 0 0 117 118 119 120 121 122 123 124 125 DFS BOB HO1CH IFR CONV ORRT CNI AOC MGCOT 0 0 0 0 0 0 0 0 0 OSGS ONSG ISGS INSG TF TC
PAGE 71
Get: Main Memory +-------------+---------+-----------+------------+ | Type Version Issue Date | +-------------+---------+-----------+------------+ |Main Memory | 15 | 02.00 | 2003/10/09 | |Boot ROM | H | 02.00 | 2002/11/20 | |IP | | | | |ACDP | | | | |MAT | 15 | 02.00 | 2003/09/05 | |TCP/IP | 5 | 01.00 | 2003/09/04 | |PHDP | 2 | 02.
PAGE 72
Important Information THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
PAGE 73
Corporate Headquarters European Headquarters Americas Headquarters Asia Pacific Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Cisco Systems International BV Haarlerbergpark Haarlerbergweg 13-19 1101 CH Amsterdam The Netherlands www-europe.cisco.com Tel: 31 0 20 357 1000 Fax: 31 0 20 357 1100 Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA www.cisco.