Data Sheet

Data Sheet
© 1992-2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information. Page 12 of 15
Feature
Description
●
OLD-CISCO-TS-MIB
●
RFC1213-MIB
●
RFC1398-MIB
●
RMON-MIB
●
RMON2-MIB
●
SMON-MIB
●
SNMP-FRAMEWORK-MIB
●
SNMP-MPD-MIB
●
SNMP-TARGET-MIB
●
SNMPv2-MIB
●
TCP-MIB
●
UDP-MIB
Standards
●
IEEE 802.1x support
●
IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
●
IEEE 802.1s Multiple Spanning Tree Protocol (MSTP)
●
IEEE 802.3x full duplex on 10BASE-T, 100BASE-TX, and 1000BASE-T ports
●
IEEE 802.1D Spanning-Tree Protocol
●
IEEE 802.1p CoS prioritization
●
IEEE 802.1Q VLAN
●
IEEE 802.3 10BASE-T specification
●
IEEE 802.3u 100BASE-TX specification
●
IEEE 802.3ab 1000BASE-T specification
●
IEEE 802.3ad Link Aggregation Control Protocol (LACP)
●
IEEE 802.3ah Ethernet in the First Mile (EFM)
●
RMON I and II standards
●
SNMPv1, SNMPv2c, and SNMPv3
Connectors and cabling
●
10BASE-T/100BASE-TX ports: RJ-45 connectors; four-pair Category 5 UTP
cabling
●
1000BASE-T ports: RJ-45 connectors; four-pair Category 5 UTP cabling
●
100BASE-FX ports: MT-RJ connectors; 50/125 or 62.5/125 micron multimode
fiber-optic cabling
●
100BASE-LX ports: LC connectors; 9/125 micron single-mode fiber-optic cabling
●
Management console port: 8-pin RJ-45 connector, RJ-45-to-RJ-45 rollover cable
with RJ-45-to-DB9 adapter for PC connections; for terminal connections, use RJ-
45-to-DB25 female data-terminal-equipment (DTE) adapter (can be ordered
separately from Cisco, part number ACS-DSBUASYN=)
MT-RJ patch cables for
Cisco Catalyst 2955
Type of cable, Cisco part number
●
One-meter, MT-RJ-to-SC multimode cable, CAB-MTRJ-SC-MM-1M **
●
Three-meter, MT-RJ-to-SC multimode cable, CAB-MTRJ-SC-MM-3M
●
Five-meter, MT-RJ-to-SC multimode cable, CAB-MTRJ-SC-MM-5M
●
One-meter, MT-RJ-to-ST multimode cable, CAB-MTRJ-ST-MM-1M
●
Three-meter, MT-RJ-to-ST multimode cable, CAB-MTRJ-ST-MM-3M
●
Five-meter, MT-RJ-to-ST multimode cable, CAB-MTRJ-ST-MM-5M
●
Two-meter, LC to SC single-mode cable, CAB-CP-LCSC-2M
** The port on the switch is a receptacle (female) it requires a cable with male plug
connector with two pin holes on it.
Indicators
●
Per-port status LEDs: Link integrity, disabled, activity, and indications
●
Dual-power-supply indicators
●
Major and minor alarm-relay indicators
Dimensions and weight
(HxWxD)
●
3.78x8.07x5.03 in. (9.60x20.50x12.78 cm): Connectors facing forward
●
5.03x8.07x3.78 in. (12.78x20.50x9.60 cm): Connectors facing downward
●
3.0 lb (1.4 kg)
Relay contacts
●
Surge withstand between open contacts: 1500V, FCC Part 68
●
Surge withstand between contact and coil: 2500V, Bellcore
●
Maximum switching capacity: 1A @ 30 VDC
●
Maximum switching voltage: .3A @ 125 VAC