Catalyst Switch Cable, Connector, and AC Power Cord Guide Contents TAC Notice: What's Changing on TAC Web Help us help you. Introduction Please rate this document. Prerequisites Excellent Requirements Components Used Good Conventions Average Console and Aux Port Cables Fair Which RJ-45 Ethernet Cable Do I Use? Poor Cables to Hubs, Switches, Routers, and Workstations This document Most Common Cable Connectors solved my GBIC and SFP Connectors problem.
NetPro Discussion Forums - Featured Conversations Related Information Introduction This document is a guide to cables and connectors for Catalyst 6500/6000, 5500/5000, and 4500/4000 series switching modules and Catalyst 2900/3500 XL, 2940, 2970, 2950/2955, 3550, and 3750 series fixedconfiguration switches. AC power supplies, connectors, and cords for these switches are also covered.
Which RJ-45 Ethernet Cable Do I Use? A common question that concerns RJ-45 unshielded twisted pair (UTP) Ethernet cable concerns how to distinguish between rolled, straight-through, and crossover cables, and when to use them. Use the comparison guide found in the Types of RJ-45 Cabling section of Cabling Guide for Console and AUX Ports in order to see the difference between these cables.
This is used in order to connect to 10/100 or 10/100/1000 Ethernet ports and 1000Base-T Gigabit Interface Converter (GBIC) or small form factor pluggable (SFP) GBIC ports. 10/100/1000 Ethernet ports must use four twisted-pair Category 5, 5e or 6 cables. This is used in order to connect to 10/100BASE-TX RJ-21 telco interfaces. Use Category 5 UTP cables with male RJ-21. MT-RJ Fiber-Optic SC Fiber-Optic This is used in order to connect to 100Base-FX fiberoptic ports.
LC Fiber-Optic This is used in order to connect to SFP fiber-optic module ports. StackWise GigaStack This is used in order to connect to GigaStack GBIC ports. Cisco GigaStack technology uses proprietary GBICs and cables.
This is used in order to connect to StackWise ports on the rear panel of Catalyst 3750 switches. Cisco StackWise technology uses proprietary connectors and cables. GBIC and SFP Connectors Many Catalyst switches, Supervisor Engines and switching modules have removable Gigabit Interface Converters (GBICs) or small form factor pluggable (SFP)-type connectors. These diagrams show some of the most common GBIC and SFP connectors used on Catalyst switches.
This uses Cisco Gigastack connector and cable. Part Number: WS-X3500-XL (GigaStack GBIC) This uses LC fiber-optic connector or RJ-45 for 1000Base-T SFP. Part numbers: GLC-T (1000Base-T SFP) GLC-SXMM (1000Base-SX SFP) GLC-LH-SM (1000BaseLX/LH SFP) GLC-ZX-SM (1000Base-ZX) GBIC and SFP support depends on the platform and software version.
Refer to FlexWAN Module Port Adapter Install/Config Notes for FlexWAN port adapter cabling and specifications.
Ethernet ports (used with Supervisor 720 only) WS-X6516GE-TX 16 10/100/1000 Base-T Gigabit Ethernet ports RJ-45 (for 1000Base-T GBIC) WS-X6148RJ21V WSX6248-TEL WSX6248ATEL WSRJ-21 telco (4 X6348connectors) RJ21V WSX6548-RJ21 48 Port 10/100 Ethernet ports Category 5, 5e, or 6 UTP Category 5 UTP cable WS-X602410FL-MT 24 10BaseFL ports WS-X6224100FX-MT WS-X6324100FX-MM WS-X6324100FX-SM WS-X6524100FX-MM 24 100BaseFX ports Catalyst 6500/6000 Hardware Guide MT-RJ fiberoptic SMF/MMF fiber-optic
WS-X6416GE-MT 16 100Base-FX Gigabit Ethernet ports (1000Mbps) WS-X6408GBIC WSX6408AGBIC WSX6416GBIC WSX6516GBIC WSX6516AGBIC WSX6816GBIC 8 or 16 GBIC module slots MT-RJ fiberoptic MMF fiberoptic RJ-45 (for 1000Base-T GBIC) Category 5, 5e, 6 UTP SC fiber-optic 1 (1000BaseSX/ MMF fiberoptic LX/ZX and CWDM GBICs) WS-X650110GEX4 1 port 10Gigabit Ethernet WS-X650210GE with Optical Interface Module SC fiber-optic (OIM) 1-port 10-Gigabit Ethernet WS-X670410GE 4 port 10-Gigabit Ethernet (used with Supervisor
WS-X6724SFP 24 SFP module slots (used with Supervisor 720 only) RJ-45 (for 1000Base-T SFP) Category 5, 5e, 6 UTP LC fiber-optic (for 1000Base- SMF/MMF SX/LX/ZX fiber-optic SFPs) 1 LX/LH GBICs require a mode-conditioning patch cord between the GBIC and MMF. Refer to the ModeConditioning Patch Cord section of the document Connector and Cable Specifications for more information. Catalyst 5500/5000 Connectors and Cables Identify the switching module part number.
WS-X5203 WSX5213A 12 10/100 Ethernet ports RJ-45 or 5 UTP cable 1 WS-X5224 WSX5225R WS-X5234RJ45J45 24 10/100 Ethernet ports WS-X5012 WSX5012A WS-X5020 48 Port 10Base-T Ethernet ports RJ-21 telco Category 3 or 5 UTP cable 1 WS-X5239RJ21 48 10/100 Ethernet ports WS-X5015MT 24 10Base-FL ports MT-RJ fiberWS-X5236optic FX-MT WS-X5237FX-MT 24 100BaseFX SMF/MMF fiber-optic Catalyst 5000 Hardware Guide
WS-X5114 WS-X5201 SC fiber-optic WS(for 100BaseX5201R 12 FX) 100BaseFX ports WS-X5403 3 port GBIC modules slots WS-X5410 9 GBIC module slots SC fiber-optic (for 1000BaseSX/ LX/ZX GBICs) SMF/MMF fiber-optic SMF/MMF 2 fiber-optic 1 Category 3 UTP cable can transmit data at speeds of up to 10 Mbps and therefore is only used for 10 Mbps network devices. Catalyst 5000 10Base-T telco switching modules can use Category 3 cable, but Category 5 cable is required for all other 10/100 Base-TX switching modules.
sales representative: ● CAB-STACK-50CM= (0.
WS-C3750G12S 12 SFP module slots SFP: LC fiber-optic (for 1000BaseSX/LX) or RJ-45 (for 1000Base-T) SFP: SMF/ MMF fiberoptic, or Cat5, 5e, or 6 Catalyst 3560/3560E Connectors and Cables Identify the switch chassis part number. Use this table in order to match up the part number with the type of connector and cable used.
48PS SFP (1000BaseLH/SX/ZX) WSC3560G24TS, WSC3560G48TS, WSC3560G24PS, WSC3560G48PS WSC3560E24TD, WSC3560E24PD, WSC3560E48TD, WSC3560E48PD, WSC3560E48PD-F RJ-45 (10/100/1000) SFP (1000BaseT) SFP (1000BaseLH/SX/ZX) RJ-45 (10/100/1000) SFP (1000BaseT) LC Fiberoptic SMF/ MMF Four pair Cat 5, 5e, or 6 UTP Also refer to Cisco Small Form-Factor Pluggable (SFP) Transceiver Modules Maintenance and Troubleshooting.
CAB-SFP50CM= Cisco Catalyst 3560 SFP Interconnect Cable (50 dcm) Catalyst 3550 Connectors and Cables Identify the switch chassis part number. Use this table in order to match up the part number with the type of connector and cable used. Note: Some Catalyst 3550 switches support the GigaStack GBIC, which requires a Cisco proprietary cable of either CAB-GS-50CM (0.5-meter cable) or CAB-GS-1M (1-meter cable).
DC-SMI WSC3550-48SMI WSC3550-24EMI WSC3550-48EMI 24 or 48 10/100 Ethernet GBIC: RJ-45 ports and 2 for 1000BaseGBIC T GBIC or module slots SC fiberoptic (for WS-C35501000Base-SX/ 24PWR-SMI LX/ZX and WS-C3550CWDM 24PWRGBICs) or EMI Gigastack 2410/100 GBIC inline-power Ethernet ports and 2 GBIC module slots WS-C355024-FX-SMI 24 100BaseFX ports and 2 GBIC module slots GBIC: Cat 5, 5e, 6 UTP or MMF/SMF fiber-optic or GigaStack cable MT-RJ fiberoptic (for 100Base-FX ports) MMF fiberoptic GBIC: RJ-45 for 1000
Catalyst 2970 Connectors and Cables Part Number Connector Type WS-C2970G24T 24 RJ-45 10/100/1000 Ethernet WS-C2970G24TS 24 10/100/1000 and 4 SFP module slots Cable Type Cable/ Connector Specifications Category 5, 5e, or 6 UTP RJ-45 (for 10/100/1000 ports) Category 5, 5e, or 6 UTP SFP: RJ-45 (for 1000Base-T) or LC fiberoptic (for 1000Base-SX/ LX/ZX) SFP: Cat5, 5e, or 6 UTP or SMF/ MMF fiberoptic Catalyst 2970 Hardware Guide Catalyst 2950/2955 Connectors and Cables Identify the switch chassis part
WS-C2950-12 and WSC2950-24 12 or 24 10/100 Ethernet ports WS-C2955C12 and WSC2950C-24 12 or 24 10/100 Ethernet ports and 2 100BASEFX ports WS-C2950G12-EI, WSC2950G-24EI, WSC2950G-24-EIDC, and WSC2950G-48-EI 12, 24, or 48 10/100 Ethernet ports and 2 GBIC module slots WS-C2950SX24 and WSC2950SX-48SI 24 or 48 10/100 Ethernet ports and 2 1000BASESX ports RJ-45 Category 5, 5e, or 6 UTP cable RJ-45 (for 10/100 ports) Category 5, 5e, or 6 UTP cable MT-RJ fiber-optic MMF fiberoptic RJ-45 (for 10/100 ports)
WS-C2955T12 WSC2950T-24 WS-C2950T48-SI 12, 24 or 48 10/100 Ethernet ports and 2 10/100/1000 Ethernet ports WS-C2955S12 12 10/100 Ethernet ports and 2 100BaseLX ports RJ-45 Category 5, 5e, or 6 UTP cable RJ-45 (for 10/100 ports) Category 5, 5e, or 6 UTP MT-RJ fiber-optic SMF fiberoptic Catalyst 2940 Connectors and Cables Identify the switch chassis part number. Use this table in order to match up the part number with the type of connector and cable used.
SFP module slot SFP: RJ-45 (for 1000Base-T) or LC fiberoptic (for 1000BaseX) SFP: Cat5, 5e, or 6 UTP or SMF/ MMF fiber-optic Catalyst 2900/3500 XL Connectors and Cables Identify the switch chassis or expansion module part number. Use this table in order to match up the part number with the type of connector and cable used. Note: This guide does not cover the WS-C2912-LRE-XL or WS-C2912-LRE-XL switches.
XL 12, 24 or 48 10/100 or 10/100 inline power Ethernet ports and 2 GBIC module slots GBIC: SC fiber-optic (for 1000BaseSX/LX/ZX GBICs) or Gigastack GBIC Catalyst 3500XL Hardware GBIC: MMF/ Guide SMF fiberoptic or Catalyst GigaStack cable 2900XL Hardware Guide WS-C2912XL WSC2924-XL RJ-45 12 or 24 10/100 Ethernet ports Category 5 UTP WSC2924CXL 22 10/100 Ethernet ports and 2 100BaseFX ports MMF fiberoptic SC fiberoptic (for 100Base-FX ports) Catalyst 2900XL Switches with Expansion Slots Switch Chassis
Hardware Guide WSC2912MFXL 12 100BaseFX ports and 2 expansion slots SC fiberoptic (for 100Base-FX ports) MMF fiberoptic Catalyst 2900XL Expansion Modules Switch Chassis Part Number WS-X2914XL WSX2914-XLV 4 10/100 Ethernet ports Connector Type RJ-45 Cable Description Cable/ Connector Specifications Category 5 UTP WS-X2922XL 2 10/100 Ethernet ports WS-X2922XL-V 2 100BaseSC fiberFX ports optic (for 100 BaseWS-X2924FX) XL-V 4 100BaseFX ports MMF fiberoptic SC fiberWS-X2931optic (for XL 1 GBIC SX/LX
WS-X2932- RJ-45 (for XL 1 GBIC 1000Base-T module slot GBIC) WS-X2951RJ-45 (for Category 5 XL 1 ATMATM-OC-3) UTP OC-3 WS-X2961- SC fiberMMF fiberXL 1 ATM- optic (for optic OC-3 ATM-OC-3) WS-X2971SC fiberXL WSSMF fiberX2972-XL optic (for optic 1 ATM-OC- ATM-OC-3) 3 AC Power Supplies, Connectors, and Cords for Catalyst Switches In this section you see the summary of AC power supplies, power connectors, and cords for Catalyst 6500/6000, 5500/5000 and 4500/4000 series, and Catalyst 3750, 2950, 2940, and 2900/35
● ● ● ● ● The 950W (PWR-950-AC), 950W DC (PWR-950-DC) and 1400W AC (PWR-1400-AC) are used only with the Catalyst 6503 and Catalyst 6503-E Switches. The Power supplies 1000W and 1300W can be used only with Catalyst 6506, 6509, and 6509-NEBA switches. The Supervisor Engines SUP32 and SUP720 are incompatible when 1000W and 1300W power supplies are used. With a fully populated Catalyst 6513 switch, two 2500 W power supplies are not fully redundant.
AC Input 1 110Vac, 16A Net Power Supply Output AC Input 2 Not Connected No Power Output Not Connected 110Vac, 16A No Power Output 110Vac, 16A 110Vac, 16A 2900W 220Vac, 16A Not Connected 2900W Not Connected 220Vac, 16A 2900W 110Vac, 16A 220Vac, 16A 2900W 220Vac, 16A 110Vac, 16A 2900W 220Vac, 16A 220Vac, 16A 6000W Note: If you have 110Vac power inputs, you have to connect both the AC inputs of the 6000W power supply in order to power on the switch.
PWR950-AC 950W CABpower 7KAC-15 supply AC Power Cord WSNorth CAC1000W America, 1000W 15A power supply WSCAC1300W 1300W Power Supply CAB7513AC AC Power Cord North America (110Vac, 20A) CAB7513AC= AC Power Cord North America (110Vac, 20A) PWR1400AC 1400W Power Supply CAB-AC2500WUS1= 250Vac 16A, straightblade NEMA 620 plug
CAB-ACC6KTWLK= 250Vac 16A, twist-lock NEMA L6-20 plug CAB7513AC AC Power Cord North America (110Vac, 20A) WSCAC2500W 2500W AC Power Supply CAB-AC2500WUS1 250Vac 16A, straightblade NEMA 620 plug CAB-ACC6KTWLK 250Vac 16A, twist-lock NEMA L6-20 plug Catalyst 6500/6000
PWR2700AC/4 2700W AC Power Supply CAB7513AC AC Power Cord North America (110Vac, 20A) CAB-AC2500WUS1 250Vac 16A, straightblade NEMA 620 plug CAB-ACC6KTWLK 250Vac 16A, twist-lock NEMA L6-20 plug CAB7513AC= 110Vac 20A, NEMA 520 plug WSCAC3000W 3000 W ACinput power
supply CAB-AC2500WUS1= 250Vac 16A, straightblade NEMA 620 plug CAB-ACC6KTWLK= 250Vac 16A, twist-lock NEMA L6-20 plug WSCAC4000WUS 4000W AC Power Supply Cableattached to the power supply 250Vac 30A CAB7513AC= 110Vac 20A, NEMA 520 plug WSCAC6000W 6000W AC Power supply CAB-AC2500WUS1= 250Vac 16A, straightblade NEMA 620 plug
CAB-ACC6KTWLK= 250Vac 16A, twist-lock NEMA L6-20 plug Catalyst 5500/5000 Series Switch Power Supplies and Cables This table has a quick reference for the available power supplies and the Power cord part number.
CAB7KAC WSC5518 (Catalyst 5509) CAB7513AC Catalyst 4500/4000 Series Switch Power Supplies and Cables Refer to the Power Connection Guidelines for AC-Powered Systems section in Catalyst 4500 Series Hardware Installation Guide - Preparing for Installation for the list of Power supplies, cables and the corresponding part numbers. Refer to Catalyst 4000 Series Installation Guide - Site Planning for the list of Catalyst 4000 Power supplies, cables and the corresponding part numbers.
Power Supply Part Number Power Cord Part Number Connector Type Internal nonCABreplaceable AC= AC power supply Power Installation Guidelines N/A RJ-21 to RJ-45 Pin-Out Pattern All Catalyst family 10/100TX telco switching modules incorporate industry-standard RJ-21 connectors and require compatible Category 5 cabling systems to achieve 100 Mbps data rates. Category 5 telco cables can be ordered directly from Cisco. Refer to Cisco.com for ordering information.
RJ-21 Pin Number RJ-45 Pin Number Wire Color 26 White/Blue 1 1 Blue/White 2 27 White/ Orange 3 2 Orange/ White 6 28 White/Green 1 3 Green/White 2 29 White/ Brown 3 4 Brown/ White 6 30 White/Slate 1 5 Slate/White 2 31 Red/Blue 3 6 Blue/Red 6 32 Red/Orange 1 7 Orange/Red 2 33 Red/Green 3 8 Green/Red 6 34 Red/Brown 1 9 Brown/Red 2 35 Red/Slate 3 10 Slate/Red 6 36 Black/Blue 1 11 Blue/Black 2 Port Number 1 2 3 4 5 6
37 Black/ Orange 3 12 Orange/ Black 6 38 Black/Green 1 13 Green/Black 2 39 Black/ Brown 3 14 Brown/ Black 6 40 Black/Slate 1 15 Slate/Black 2 41 Yellow/Blue 3 16 Blue/Yellow 6 42 Yellow/ Orange 1 17 Orange/ Yellow 2 43 Yellow/ Green 3 18 Green/ Yellow 6 44 Yellow/ Brown 1 19 Brown/ Yellow 2 45 Yellow/Slate 3 20 Slate/Yellow 6 46 Violet/Blue 1 21 Blue/Violet 2 47 Violet/ Orange 3 7 8 9 10 11
22 Orange/ Violet 48 Violet/Green 1 23 Green/Violet 2 49 Violet/ Brown 3 24 Brown/ Violet 6 50 Violet/Slate NA NA 25 Slate/Violet NA NA 6 12 NetPro Discussion Forums - Featured Conversations Networking Professionals Connection is a forum for networking professionals to share questions, suggestions, and information about networking solutions, products, and technologies. The featured links are some of the most recent conversations available in this technology.
● Technical Support & Documentation - Cisco Systems Contacts & Feedback | Help | Site Map © 2008 - 2009 Cisco Systems, Inc. All rights reserved. Terms & Conditions | Privacy Statement | Cookie Policy | Trademarks of Cisco Systems, Inc.
