Datasheet

© 2015 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information. Page 3 of 6
Module
SFP
Wavelength
(nm)
Fiber/Cable
Type
Core Size
(micron)
Model Bandwidth
(MHz/km)
Cable Distance
C6800-48P-SFP and
C6800-48P-SFP-XL
1000BASE-T
-
Category 5
-
-
100 m (328 ft)
*
Mode-conditioning patch is required. Using an ordinary patch cord with MMF, 1000BASE-LX/LH SFP/GBICs, and a short link distance (10s of
meters) can cause transceiver saturation resulting in an elevated bit error rate (BER). In addition, when using the LX/LH SFP/GBIC with 62.5
micron diameter MMF, you must install a mode-conditioning patch cord between the SFP and the MMF cable on both the transmit and receive
ends of the link. The mode-conditioning patch cord is required for link distances greater than 300 m (984 ft).
**
1000BASE-ZX-SFP can reach up to 100 km by using dispersion-shifted SMF or low attenuation SMF; the distance depends on fiber quality,
number of splices and connectors.
For complete list of transceivers supported by the C6800 1 Gigabit Fiber modules please refer to “Cisco Gigabit
Ethernet Transceiver Modules Compatibility Matrix” at
http://www.cisco.com/c/en/us/td/docs/interfaces_modules/transceiver_modules/compatibility/matrix/GE_Tx_Matrix.
html.
Platform Support/Compatibility
Table 3 describes platform support and compatibility for the 48-port 6800 Gigabit Ethernet modules.
Table 3. Platform Support/Compatibility
Feature
48-Port 6800 Series Gigabit Ethernet Fiber Modules
48-Port 6800 Series Gigabit Ethernet Copper Modules
Supervisor
engines supported
Cisco Catalyst 6500 Supervisor Engine 2T and 2TXL
Cisco Catalyst 6500 Supervisor Engine 2T and 2TXL
Chassis supported
● Any Cisco Catalyst 6807-XL, 6500 E-Series chassis,
including 6503-E, 6504-E, 6506-E, 6509-E, 6509-V-E
(NEBS compliant) and 6513-E chassis
● Not supported in non-E Series chassis
● Any Cisco Catalyst 6807-XL, 6500 E-Series chassis,
including 6503-E, 6504-E, 6506-E, 6509-E, 6509-V-E
(NEBS compliant) and 6513-E chassis
● Not supported in non-E Series chassis
Slot requirements
● Can occupy slots 1-3 and 6-7 in a Cisco Catalyst
6807-XL chassis
● Can occupy slots 1-6 and 9-13 in a Cisco Catalyst
6513-E chassis
● Can occupy any slot in any Cisco Catalyst 6503-E,
6504-E, 6506-E, 6509-E or 6509-V-E or chassis
● Can occupy slots 1-3 and 6-7 in a Cisco Catalyst
6807-XL chassis
● Can occupy slots 1-6 and 9-13 in a Cisco Catalyst
6513-E chassis
● Can occupy any slot in any Cisco Catalyst 6503-E,
6504-E, 6506-E, 6509-E or 6509-V-E or chassis
Product Specifications
Table 4 lists product specifications of the C6800 Series Gigabit Ethernet Fiber and Copper Modules.
Table 4. Product Specifications
Item
Specification(s)
Standard protocols
● IEEE 802.1d, IEEE 802.1p, IEEE 802.1q, IEEE 802.1s, IEEE 802.1w, IEEE 802.3x, IEEE 802.3z, IEEE 802.3ab,
and IEEE 802.3ad
● 1000BASE-T, 1000BASE-X (GBIC), 1000BASE-SX, 1000BASE-LX/LH, 1000BASE-ZX, CWDM
Physical specifications
● Occupies one slot in the Cisco Catalyst 6807-XL or one slot in the 6500 E-Series chassis
● Dimensions (H x W x D): 1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm)
Environmental
conditions
Temperature:
● Operating temperature: 32 to 104°F (0 to 40°C)
● Storage temperature: -40 to 167°F (-40 to 75°C)
● Relative humidity 10 to 90% noncondensing
Operating altitude:
● Agency-certified for operation: -500 to 6500 ft (-150 to 2000m)
● Designed and tested for operation -500 to 10000 ft (-150 to 3000m)
NEBS criteria levels
SR-3580 Issue 3, June 2007 (GR-63-CORE, issue 3, and GR-1089-CORE, issue 4)
ETSI
● ETS 300 019-2-1, Class 1.1 Storage
● ETS 300 019-2-2, Class 2.1 and 2.2 Transportation
● ETS 300 019-2-3, Class 3.1E Stationary Use