Catalyst 4500 Series Switch Cisco IOS Command Reference Release IOS XE 3.3.0XO(15.1(1)XO) Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMA TION REGARDING TH E PRODUCT S IN TH IS MA NUAL A RE SUBJECT TO CH ANGE WITHOU T NOT ICE. AL L STAT EM ENT S, INFORMA TIO N, AND RECOM MEN DATIONS IN THIS MANUA L ARE BEL IE VED T O BE ACCURATE BU T ARE PRESE NTE D WIT HOUT WA RRAN TY OF AN Y KIN D, E XPRESS OR IMPLIED. USE RS MUST T AKE F ULL RE SPONSIBILITY FOR TH EIR APPL ICAT ION O F ANY PRODUCT S.
CH AP T E R Catalyst 4500 Series IOS Commands A Commands aaa accou nting dot1x d efault start-stop group radiu s aaa accou nting system defau lt start-stop group rad iusclear mac-ad dress-table access-group mode access-list hardware cap ture mode access-list hardware entries access-list hardware region action ap ply an cp clien t serv er an cp mode client ap ply arp access -list attach mo dule au then tication contro l-direction au then tication critical recovery delay au then tication event au then ticati
Chapter au to q os classify p olice au to q os srnd 4 au to q os trust au to q os video au to q os voip au to q os voip cisco-softphone au to-sy nc C Commands call-home (global con figuratio n) call-home req ues t call-home send call-home send alert-g roup call-home test ch ann el-gro up ch ann el-pro toco l cisp enable class-map clear counters clear errdisab le clear hw-modu le slot password clear interface gig abitethern et clear interface vlan clear ip access-template clear ip arp inspectio n log clear
Chapter clear port-security clear pppo e intermediate-agen t statistics clear qos clear vlan cou nters clear vmps statistics co ntrol-plane co unter D Commands debug ad jacen cy debug backu p debug co ndition interface debug co ndition standby debug co ndition vlan debug dot1x debug etherchn l debug interface debug ip dhcp s noopin g even t debug ip dhcp s noopin g p acket debug ip verify sou rce packet debug ipc debug lacp debug monitor debug nmsp debug nv ram debug pagp debug platform p acket protocol l
Chapter debug sw-vlan ifs debug sw-vlan n otificatio n debug sw-vlan v tp debug udld debug vqpc define in terface-range deny diagnostic fpga soft-error recover diagnostic monitor action diagnostic start dot1x auth-fail max-attempts dot1x auth-fail v lan dot1x credentials (glob al co nfigu ration) dot1x critical dot1x critical eapol dot1x critical recovery delay dot1x critical vlan dot1x control-d irectio n dot1x gu est-vlan dot1x gu est-vlan supplican t dot1x ho st-mod e dot1x initialize dot1x mac-auth-byp
Chapter F Commands flowcon trol H Commands hardware statistics hw-module beacon hw-module power hw-module system max-queue-limit I Commands instance interface interface po rt-channel interface rang e interface vlan ip admis sion pro xy http refresh-all ip arp inspectio n filter vlan ip arp inspectio n limit (interface) ip arp inspectio n lo g-bu ffer ip arp inspectio n trust ip arp inspectio n validate ip arp inspectio n v lan ip arp inspectio n v lan log ging ip cef load-sharing algorithm ip dhcp snoopi
Chapter ip igmp snoop ing ip igmp snoop ing report-sup pression ip igmp snoop ing vlan ip igmp snoop ing vlan explicit-tracking ip igmp snoop ing vlan immediate-leave ip igmp snoop ing vlan mrouter ip igmp snoop ing vlan static ip local-pro xy-arp ip mfib fastdrop ip source binding ip sticky -arp ip verify header vlan all ip verify so urce ip verify un icast source reachable-viaip wccp ip wccp check serv ices all ip wccp group -listen ip wccp red irect p wccp red irect exclu de in ipv6 mld snoo ping ipv6 m
Chapter l2protocol-tu nnel sh utdown-thresh old lacp port-p riority lacp system-p riority lldp tlv-s elect power-management logging even t trunk-status global (glob al configu ration) logging even t link -status global (glo bal configuration) logging even t trunk-status global (glob al configu ration) logging even t link -status global (glo bal configuration) logging even t link -status (in terface co nfigu ration) logging even t trunk-status (interface con figuratio n) M Commands match mac access-list ex
Chapter match flow ip md ix auto media-typ e mo de mo nitor cap ture {access-list | class-map} mo nitor cap ture [clear | export] mo nitor cap ture [interface | v lan | control-plane] mo nitor cap ture file location buffer-size mo nitor cap ture limit mo nitor cap ture mycap match mo nitor cap ture start mo nitor session mtu O Commands N Commands name P Commands pagp learn-meth od pagp po rt-prio rity p assive-interface p ermit p olicy-map port-ch ann el load-b alance p ort-ch ann el standalone-disable p
Chapter power inlin e police power red undancy -mod e pppo e intermediate-ag ent (global) pppo e intermediate-ag ent (interface) pppo e intermediate-ag ent (interface vlan-range) pppo e intermediate-ag ent format-ty pe (global) pppo e intermediate-ag ent limit rate pppo e intermediate-ag ent trust pppo e intermediate-ag ent vendor-tag strip prio rity private-vlan private-vlan mapp ing private-vlan synchro nize Q Commands qos account layer-all en capsulation qos account layer2 encapsu latio n qos tru st qu
Chapter set dscp set preced ence set qos-gro up sh ape (in terface co nfiguration) sh ell trig ger sh ow monitor capture sn mp ifindex clear sn mp ifindex persist sn mp-server enable traps sn mp-server ifindex persist sn mp-server ifindex persist co mpress sn mp trap mac-n otification change sp ann ing-tree backbonefast sp ann ing-tree bpd ufilter sp ann ing-tree bpd uguard sp ann ing-tree cost sp ann ing-tree etherchan nel gu ard misco nfig sp ann ing-tree exten d s ystem-id sp ann ing-tree guard sp ann i
Chapter storm-control storm-control b roadcas t include multicast switchport switchport access vlan switchport auto state exclude switchport block switchport mode switchport port-secu rity switchport private-vlan asso ciation tru nk switchport private-vlan host-asso ciation switchport private-vlan mapp ing switchport private-vlan trunk allowed vlan switchport private-vlan trunk n ative vlan tag switchport trun k switchport vlan mappin g system mtu Show Commands show access-g roup mo de interface show adja
Chapter sh ow environment sh ow errd isable detect sh ow errd isable recovery sh ow eth erch ann el sh ow flowcon trol sh ow idprom sh ow interfaces sh ow interfaces cap abilities sh ow interfaces counters sh ow interfaces descriptio n sh ow interfaces link sh ow interfaces mtu sh ow interfaces private-v lan mapping sh ow interfaces status sh ow interfaces switchp ort sh ow interfaces trans ceiver sh ow interfaces trunk sh ow ip arp inspectio n sh ow ip arp inspectio n lo g sh ow ip cef vlan sh ow ip dhcp
Chapter show ipv6 mld sno oping mrouter show ipv6 mld sno oping qu erier show ipv6 sn ooping coun ters show issu cap ability show issu clien ts show issu comp-matrix show issu endpo ints show issu entities show issu fsm show issu message show issu negotiated show issu rollback-timer show issu sessions show issu state show l2protocol-tunnel show lacp show mab show mac access-group interface show mac-address-tab le address show mac-address-tab le aging-time show mac-address-tab le count show mac-address-tab
Chapter sh ow pagp sh ow policy-map sh ow policy-map co ntro l-plane sh ow policy-map interface sh ow policy-map interface vlan sh ow port-secu rity sh ow power sh ow power inline police sh ow qos sh ow pppoe intermediate-ag ent interface sh ow qos sh ow qos aggregate policer sh ow qos dbl sh ow qos interface sh ow qos map s sh ow redund ancy sh ow redund ancy config-sync sh ow run ning-co nfig sh ow slavebootflash: sh ow slaveslot0: sh ow slot0: sh ow spanning-tree sh ow spanning-tree mst sh ow storm-cont
Chapter show vtp T Commands test cab le-diagnostics tdr traceroute mac traceroute mac ip trus t tx-q ueu e U Commands udld (global configuration mo de) udld (interface configu ration mode) udld reset unidirectional username V Commands verify vlan (VLAN Database mod e) vlan access-map vlan configuratio n vlan d atabase vlan d ot1q tag n ative vlan filter vlan g rou p vlan in ternal allocatio n p olicy vmps reconfirm (glo bal config uration) vmps reconfirm (privileged EXEC) vmps retry vmps server vtp (g l
Chapter v tp v 2-mo de Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
C ON TE N TS Preface xxi Audience xxi Cisco IOS Software Documentation Organization Notices xxi xxi Related Documentation Conventions xxii xxii xxiii Obtaining Documentation and Submitting a Service Request Command-Line Interface Getting Help 1-2 1-5 Using the CLI String Search 1-6 1-6 Saving Configuration Changes show platform Commands 1-11 1-11 Cisco IOS Commands for the Catalyst 4500 Series Switches #macro keywords access-group mode 2-9 access-list hardware region 2-5 2-11 2-8
Contents arp access-list 2-18 attach module 2-19 authentication control-direction 2-20 authentication critical recovery delay authentication event 2-25 authentication host-mode authentication open 2-22 2-23 authentication fallback 2-26 2-28 authentication order 2-29 authentication periodic 2-30 authentication port-control authentication priority 2-31 2-33 authentication timer 2-35 authentication violation 2-37 auto qos classify 2-39 auto qos classify police auto qos srnd4 2-43 2-47 auto
Conten ts clear errdisable 2-90 clear hw-module slot password clear interface gigabitethernet clear interface vlan 2-91 2-92 2-93 clear ip access-template 2-94 clear ip arp inspection log 2-95 clear ip arp inspection statistics clear ip dhcp snooping binding clear ip dhcp snooping database 2-96 2-97 2-99 clear ip dhcp snooping database statistics clear ip igmp group 2-101 clear ip igmp snooping membership clear ip mfib counters 2-105 2-106 clear lacp counters 2-107 clear mac-address-table
Contents debug etherchnl 2-132 debug interface 2-134 debug ipc 2-135 debug ip dhcp snooping event 2-136 debug ip dhcp snooping packet debug ip verify source packet debug lacp 2-137 2-138 2-139 debug monitor 2-140 debug nmsp 2-141 debug nvram 2-142 debug pagp 2-143 debug platform packet protocol lacp debug platform packet protocol pagp debug pm 2-144 2-145 2-146 debug port-security 2-147 debug pppoe intermediate-agent 2-148 debug redundancy 2-150 debug spanning-tree 2-151 debug spa
Conten ts diagnostic monitor action diagnostic start 2-173 2-174 dot1x auth-fail max-attempts dot1x auth-fail vlan 2-175 2-176 dot1x control-direction 2-177 dot1x credentials (global configuration) dot1x critical 2-180 2-181 2-182 dot1x guest-vlan 2-183 dot1x guest-vlan supplicant dot1x host-mode 2-187 2-188 2-189 2-190 dot1x port-control 2-191 dot1x re-authenticate 2-193 dot1x re-authentication 2-194 dot1x system-auth-control dot1x timeout duplex 2-184 2-184 dot1x initialize dot1
Contents interface port-channel interface range interface vlan 2-221 2-222 2-224 ip admission proxy http refresh-all ip arp inspection filter vlan 2-225 2-226 ip arp inspection limit (interface) 2-228 ip arp inspection log-buffer 2-230 ip arp inspection trust 2-232 ip arp inspection validate ip arp inspection vlan 2-233 2-235 ip arp inspection vlan logging 2-237 ip cef load-sharing algorithm 2-239 ip device tracking maximum ip dhcp snooping 2-241 2-242 ip dhcp snooping binding 2-243 ip
Conten ts ip multicast multipath ip source binding ip sticky-arp 2-272 2-274 2-275 ip verify header vlan all ip verify source 2-277 2-278 ip verify unicast source reachable-via ip wccp 2-280 2-281 ip wccp check services all ip wccp group-listen ip wccp redirect 2-284 2-286 2-288 p wccp redirect exclude in ipv6 mld snooping 2-290 2-291 ipv6 mld snooping last-listener-query-count ipv6 mld snooping last-listener-query-interval 2-293 2-295 ipv6 mld snooping listener-message-suppression ipv6
Contents logging event trunk-status global (global configuration) logging event trunk-status (interface configuration) mab 2-323 2-324 2-326 mac access-list extended 2-327 mac-address-table aging-time 2-330 mac-address-table dynamic group protocols mac address-table learning vlan 2-331 2-334 mac-address-table notification mac-address-table static 2-336 2-338 macro apply cisco-desktop macro apply cisco-phone 2-339 2-341 macro apply cisco-router 2-343 macro apply cisco-switch macro auto devic
Conten ts monitor capture [interface | vlan | control-plane] monitor capture file location buffer-size monitor capture limit mtu 2-381 2-382 2-385 monitor capture mycap match monitor capture start monitor session 2-386 2-388 2-393 2-398 name 2-399 nmsp 2-400 nmsp attachment suppress pagp learn-method pagp port-priority permit 2-407 police 2-409 2-402 2-403 passive-interface 2-404 police (percent) police rate 2-401 2-413 2-415 police (two rates) policy-map 2-417 2-421 port-channe
Contents pppoe intermediate-agent (interface) 2-440 pppoe intermediate-agent (interface vlan-range) 2-441 pppoe intermediate-agent format-type (global) 2-442 pppoe intermediate-agent format-type (interface) 2-444 pppoe intermediate-agent format-type (interface vlan-range) pppoe intermediate-agent limit rate pppoe intermediate-agent trust 2-445 2-446 2-447 pppoe intermediate-agent vendor-tag strip priority 2-448 2-449 private-vlan 2-451 private-vlan mapping 2-455 private-vlan synchronize prof
Conten ts service-policy (interface configuration) service-policy (policy-map class) 2-488 2-491 service-policy input (control-plane) session module set 2-493 2-495 2-497 set cos set dscp 2-499 2-501 set precedence 2-504 set qos-group 2-507 shape (class-based queueing) 2-508 shape (interface configuration) shell trigger 2-510 2-511 show access-group mode interface show adjacency 2-516 2-517 2-518 show auto install status show auto qos 2-513 2-514 show ancp multicast show arp access-l
Contents show etherchannel 2-561 show flowcontrol show idprom 2-565 2-567 show interfaces 2-573 show interfaces capabilities 2-576 show interfaces counters 2-580 show interfaces description show interfaces link 2-583 show interfaces mtu 2-584 2-582 show interfaces private-vlan mapping show interfaces status show interfaces trunk 2-588 2-590 2-595 show ip arp inspection 2-597 show ip arp inspection log show ip cef vlan 2-600 2-601 show ip dhcp snooping 2-602 show ip dhcp snooping bindin
Conten ts show ipv6 snooping counters show ipv6 mld snooping 2-641 2-642 show ipv6 mld snooping mrouter 2-644 show ipv6 mld snooping querier show issu capability show issu clients 2-645 2-647 2-649 show issu comp-matrix show issu endpoints show issu entities show issu fsm 2-651 2-655 2-656 2-657 show issu message 2-658 show issu negotiated 2-659 show issu rollback-timer show issu sessions show issu state 2-666 show mab 2-669 2-660 2-661 2-662 show l2protocol-tunnel show lacp 2-664 s
Contents show macro auto monitor device show macro auto monitor type show module 2-695 2-697 2-700 show monitor 2-702 show monitor capture 2-704 show monitor capture file show nmsp 2-710 show pagp 2-713 show policy-map 2-706 2-715 show policy-map control-plane show policy-map interface 2-716 2-719 show policy-map interface vlan show port-security show power 2-722 2-724 2-730 show power inline police 2-738 show pppoe intermediate-agent interface show qos 2-739 2-741 show qos aggregat
Conten ts show vlan 2-776 show vlan access-map show vlan counters 2-779 2-780 show vlan dot1q tag native show vlan group 2-781 2-782 show vlan internal usage show vlan mapping show vlan mtu 2-783 2-784 2-785 show vlan private-vlan 2-786 show vlan remote-span show vmps show vtp 2-788 2-789 2-790 snmp ifindex clear 2-793 snmp ifindex persist 2-794 snmp-server enable traps 2-795 snmp-server ifindex persist 2-797 snmp-server ifindex persist compress snmp trap mac-notification change so
Contents spanning-tree mst hello-time 2-817 spanning-tree mst max-age 2-818 spanning-tree mst max-hops 2-819 spanning-tree mst root 2-820 spanning-tree pathcost method 2-821 spanning-tree portfast (interface configuration mode) spanning-tree portfast bpdufilter default 2-822 2-824 spanning-tree portfast bpduguard default 2-825 spanning-tree portfast default spanning-tree port-priority 2-826 2-827 spanning-tree uplinkfast 2-828 spanning-tree vlan speed 2-830 2-832 storm-control 2-835 stor
Conten ts test cable-diagnostics tdr traceroute mac 2-882 2-884 traceroute mac ip trust 2-887 2-889 tx-queue 2-891 udld (global configuration mode) 2-893 udld (interface configuration mode) udld reset verify 2-895 2-897 unidirectional username 2-898 2-899 2-900 vlan (VLAN Database mode) vlan access-map 2-902 2-905 vlan configuration vlan database 2-906 2-908 vlan dot1q tag native vlan filter 2-910 2-911 vlan group 2-912 vlan internal allocation policy 2-913 vmps reconfirm (gl
Contents Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Preface This preface d escrib es the aud ience, organ ization, and conventions of th is p ublication , and prov ides info rmation on how to obtain related do cumentation. Cisco do cumentation and add itional literature are available in a CD-ROM p ackage, wh ich ship s with your prod uct. The Documen tation CD-ROM, a memb er of the Cisco Connection Family, is updated monthly. Therefore, it migh t be more u p to d ate than printed do cumentation.
Pre face Chapter Title Chapter 1 Command-Line Interface Describes the Catalys t 45 00 series switch CLI. Description Chapter 2 Cisco IOS Commands for Lists all Catalys t 45 00 series Cisco IOS th e Catalyst 450 0 Series co mmand s alphabetically and prov ides Switches detailed info rmation on each co mmand . Appendix A Abbreviations Defines the acronyms us ed in this publication.
Preface Table 1 Command Syntax Guide Co nvention Description ^ o r Ctrl Represen t the key labeled Control. For example, when yo u read ^D or Ctrl-D, you sh ould hold down the Control key while you p ress the D key. Examples o f information displayed on the screen. screen font boldface screen fo nt Examples o f information that y ou must en ter. < > Non printin g characters, su ch as pas swords, appear in an gled b rackets. [ ] Default respon ses to system pro mp ts appear in square brackets.
Pre face Redistribution and use in so urce an d bin ary forms, with or without mo dificatio n, are permitted provided th at the followin g cond itions are met: 1. Redistributions of so urce code must retain the co pyrig ht notice, this lis t of con ditions and the followin g d isclaimer. 2. Redistributions in bin ary fo rm must rep rod uce the ab ove copyright notice, th is lis t o f condition s, and th e following disclaimer in the documentatio n and/or oth er materials provided with the distribution.
Preface Obtaining Documentation and Submitting a Service Reque st Redis tribution an d use in source and binary forms, with or withou t modification, are permitted provid ed that the following conditions are met: 1. Redis tribution s o f source co de must retain the copyright notice, this list of condition s and the following disclaimer. 2.
Pre face Obtaining Documentation and Submitting a Service Request Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
CH AP T E R 1 Command-Line Interface This chap ter provid es information for un derstanding and using the Cisco IOS command-line in terface (CLI) on the Catalyst 4500 series switch.
Chapter 1 Command-Line In terface How to Find Command Options How to Find Command Options This section provides an examp le of h ow to d isplay s yntax for a co mmand . The syntax can consist of o ptional o r required k eywords . To d isplay keywo rds for a command, enter a question mark (?) at the command prompt or after entering part of a comman d followed by a sp ace. The Catalyst 4500 series switch software disp lays a list of available key words along with a b rief des cription of the keyword s.
Chapter 1 Command-Line Interface How to Find Command Options Table 1-2 How to Find Command Options (continued) Command Purpose Switch(config-if)#? Interface configuration commands: access-expression Build a bridge boolean access expression apollo Apollo interface subcommands appletalk Appletalk interface subcommands arp Set arp type (arpa, probe, snap) or timeout backup Modify backup parameters bandwidth Set bandwidth informational parameter bgp-policy Apply policy propogated by bgp community string b
Chapter 1 Command-Line In terface How to Find Command Options Table 1-2 How to Find Command Options (continued) Co mmand Purpo se Switch(config-if)# channel-group ? <1-256> Channel group number After you enter the g roup keyword , enter a ? to display wh at you must enter next o n th e comman d lin e. In this examp le, you must enter a channel group nu mber from 1 to 2 56.
Chapter 1 Command-Line Interface Understanding Command Modes Understanding Command Modes The Cis co IOS u ser interface on the Catalyst 4500 series switch has many different modes. Th e co mmand s that are available to you depen d on wh ich mode you are currently in . You can obtain a list of co mmand s available for each command mode b y enterin g a question mark (?) at the system p romp t. Wh en you s tart a ses sion on the Catalyst 450 0 series switch , y ou begin in user mode, often called EXEC mode.
Chapter 1 Command-Line In terface Using the No and Default Forms of Commands Table 1-3 Summary of Main Command Modes (continued) Co mmand Mode Access Method Prompt Subinterface co nfiguration From interface co nfiguration mode, specify a sub interface with an interface co mmand . Switch(config-subif)# To exit to g lo bal co nfiguration mod e, enter the exit command. ROM mo nitor From priv ileged EXEC mode, enter the relo ad EXEC command.
Chapter 1 Command-Line Interface Using the CLI String Search You can p erform three typ es of filtering: • Use the begin keyword to beg in o utput with the line that co ntain s a specified regular expressio n. • Use the include keywo rd to include o utput lines th at contain a specified regu lar expres sion. • Use the exclude keywo rd to ex clud e outp ut lin es that con tain a sp ecified regular expression . You can th en search th is filtered o utput at the --More-- prompts.
Chapter 1 Command-Line In terface Using the CLI String Search You can specify a ran ge of single-character patterns to match against command outp ut. For example, y ou can create a reg ular expression that match es a string co ntain ing o ne of th e fo llowing letters: a, e, i, o , or u. One and only one of these characters must exist in the string for pattern matching to su cceed. To sp ecify a range of single-character patterns, enclose th e single-character patterns in s quare b rack ets ([ ]).
Chapter 1 Command-Line Interface Using the CLI String Search You can create a mu ltiple-character regular expressio n con tainin g all letters , all dig its, all keybo ard ch aracters, or a combin ation of letters , digits, an d o ther keyb oard characters.
Chapter 1 Command-Line In terface Using the CLI String Search Alternation Alternation allows you to specify altern ative p atterns to match against a string. You sep arate the alternative patterns with a vertical bar (|). Exactly one of the altern atives can match the string. For example, the reg ular exp ression codex | telebit matches the string codex or the string telebit, but not bo th codex an d telebit.
Chapter 1 Command-Line Interface Saving Configuration Changes Parentheses for Recall As shown in the “Multipliers” section o n page 1-9, you use parentheses with mu ltiple-character regular exp ressions to multiply the occurrence of a pattern. You can also use p aren theses aroun d a single- or multiple-character p attern to remember a pattern for use elsewhere in the regu lar expression.
Chapter 1 Command-Line In terface show platform Commands Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.
CH AP T E R 2 Cisco IOS Commands for the Catalyst 4500 Series Switches This chap ter con tains an alph ab etical listing of Cis co IOS commands for the Catalyst 4500 series switches. For information about Cisco IOS commands that are not included in this pub lication, refer to Cisco IOS Release 12.2 co nfigu ration guides an d command referen ces at this URL: http://www.cisco.com/en/US/p rodu cts/sw/iosswrel/ps183 5/pro ducts_product_indices_list.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches #macro keywords #macro keywords To specify the help string for the macro key words, us e the #macro keywords command. # macro keywords [keyword1] [keyword2] [keyword3] Syntax Description keyword 1 keyword 2 keyword 3 Defaults (Optio nal) Specifies a keywo rd that is needed while applying a macro to an in terface. (Optio nal) Specifies a keywo rd that is needed while applying a macro to an in terface.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches #ma cro keywords Related Commands Co mmand macro a pply cisco -desktop macro apply cisco-phone Description Enables th e Cisco-recommended features an d s etting s that are suitable for connecting a switch port to a stan dard desktop. Enables th e Cisco-recommended features an d s etting s that are suitable for connectin g a switch port to a s tand ard des ktop an d a Cisco IP ph one.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches aaa accounting dot1x default start-stop group radius aaa accounting dot1x default start-stop group radius To en able accounting for 80 2.1X au then tication sessions, use th e aaa accounting dot1x default start-sto p group radius command. To disable accou nting, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches aaa accounting system default start-stop group radius aaa accounting system default start-stop group radius To receive the session termination messages after the switch reboots , use the aaa a ccounting system default start-stop group radius co mmand . To d isable accounting , use the no fo rm of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches access-group mode access-group mode To specify the ov erride modes (for example, VACL o verrides PACL) an d th e non -override modes (for example, merg e o r strict mod e), use th e a cces s-group mode command. To return to preferred port mode, u se the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches access-group mode Related Commands Co mmand show access-group mode interface show ip interfa ce (refer to Cisco IOS documen tation ) show ma c access-gro up interface Description Displays the ACL configuration o n a Layer 2 interface. Displays the IP interface configu ration. Displays the ACL configuration o n a Layer 2 interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches access-list hardware capture mode access-list hardware capture mode To s elect the mode o f capturing con trol packets, use th e access-list hardware ca pture mode command. a cces s-list hardware capture mode {global | v lan} Syntax Description g loba l v lan Defaults The control packets are glob ally cap tured. Specifies the capture of con trol packets glob ally on all VLANs.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches access-list hardware en tries access-list hardware entries To des ig nate how ACLs are programmed in to the switch h ardware, use the access-list hardware entries co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches access-list hardware entries Switch# This example shows how to reserve space (scatter) between ACL entries in the hardware. The number of masks required to program 49 percent of the entries has decreased to 49 percent. Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches acce ss-list hardware region access-list hardware region To mod ify the b alance between TCAM regions in hard ware, use the access -list hardware region co mmand . access-list hardwa re region { feature | qos} { input | output} balance {bal-num} Syntax Description feature qos Sp ecifies adju stment of region balan ce for ACLs. Sp ecifies adju stment of region balan ce for QoS.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches action action To specify an actio n to b e taken when a match occu rs in a VACL, use the action co mmand . To remove an action clau se, use th e no form o f this co mmand . a ction { drop | fo rward} no actio n {drop | forward} Syntax Description drop Sets the action to drop packets. forward Sets the action to forward packets to their destination. Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches active active To enable the des tinatio n p rofile, use the active command. active Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings. Command Modes Usage Guidelines Examples cfg-call-h ome-profile By defau lt the profile is enabled up on creation .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ancp client port identifier ancp client port identifier To create a map ping fo r an ANCP client to iden tify an in terface on wh ich ANCP sho uld start or stop a mu lticast s tream, use th e ancp client port identifier co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ancp client server ancp client server To set the IP address of the remote ANCP server, u se the a ncp client server comman d. ancp client server ip addr of ser ver interface interface Syntax Description ipadd r o f server interface Defaults This comman d has no default settings. IP address of the ANCP server th e client must connect with TCP. Interface to use for th e connectio n.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ancp mode client ancp mode client To set the rou ter to b ecome an ANCP client, use th e ancp mo de client comman d. ancp mode client Syntax Description This command has no arguments or keywo rds. Defaults This command has no default setting s. Command Modes Global configuratio n mo de Usage Guidelines To fully activate ANCP, the ad ministrator must also set the ANCP server IP address to which th e ANCP client mu st conn ect.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches app ly apply To implement a new VLAN database, increment the config uration numb er, save the configuration number in NVRAM, and propagate the con figuratio n numb er througho ut the administrative domain, use the apply co mmand . apply Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches arp access-list arp access-list To define an ARP access list or add claus es at the en d of a predefined lis t, use the arp access -list command. a rp access-list name Syntax Description n ame Defaults This command has no default setting s. Sp ecifies the access con trol list name.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches attach module attach module To remotely connect to a sp ecific module, use the attach module configuration command. attach module mod Syntax Description mod Defaults This comman d has no default settings. Command Modes Usage Guidelines Target mod ule for the command. Privileg ed EXEC mode This comman d app lies only to the Access Gateway Mod ule on Catalys t 45 00 series switch es.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches authentication control-direction authentication control-direction To ch ang e the p ort control to un idirectional or bidirectional, us e the a uthentication control-direction command in interface config uration mode. To return to th e default settin g, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches auth entication control-direction You can verify you r settin gs by entering the show authentication privileg ed EXEC co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches authentication critical recovery delay authentication critical recovery delay To co nfigure th e 802.1X critical auth entication parameters, use the authenticatio n critical recovery delay co mmand in glo bal config uration mode. To return to th e default settin gs, us e the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches authentication event authentication event To co nfigu re the actio ns for authentication events, use th e authentication event interface config uration co mmand . To return to the defau lt settings, use th e no form of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches authentication event The authentication ev ent fail command is su pported only for 802.1X to sign al au th en tication failures. By default, th is failu re ty pe cau ses the auth entication metho d to b e retried. You can configure eith er to autho rize the po rt in th e co nfigured VLAN o r to failover to the next auth entication metho d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches authentication fallback authentication fallback To enable Web Auth fallback and to specify th e fallb ack profile to u se when failing over to WebAu th, use the authentication fallback interface command. To return to the default setting , use the no form of this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches authentication host-mode authentication host-mode To define th e classification of a ses sion that will be used to app ly th e acces s-po licies in h ost-mo de configuration , use the authentication host-mode command in in terface co nfigu ration mode. To return to the default s etting s, use the no fo rm of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches authentication host-mode web-based authentication. Furthermore, if you use d ACLs for data dev ices and n ot for vo ice d evices, when the user’s data falls back to webauth, vo ice traffic is affected by the ACL that is applied b ased on the fallback p olicy. Th erefore if webauth is con figured as a fallback on an MDA en abled port, dACL is the on ly supported enforcemen t method. Multi-auth mo de classifies the session as a MAC-based.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches authentication open authentication open To en able open access on this po rt, u se the authentication open co mmand in interface con figuratio n mo de. To disable open access on this port, us e the no form of th is command. authentication open no authenticatio n open Syntax Description This command has no arguments or keywo rds. Command Default Disabled.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches authentication order authentication order To specify the ord er in which authenticatio n metho ds should be attempted for a client on an interface, use th e authentication order command in interface configuration mod e. To return to the default settin gs, us e the no form of th is command. authentication order meth od1 [method2] [method 3] no authentication order Syntax Description method1 Authentication method to be attempted .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches authentication periodic authentication periodic To en able reauthentication for this port, us e the authentication periodic co mmand in interface configuration mod e. To disable reau th en tication fo r this port, use the no fo rm of this comman d. authentication periodic no authentication periodic Syntax Description This command has no arguments or keywo rds. Command Default Disabled.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches authentication port-control authentication port-control To config ure the po rt-co ntrol value, use th e authentication port-control command in interface co nfiguration mode. To return to the default setting, use th e no form of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches authentication port-control o f the client and begins relaying authentication messages between the clien t and the authenticatio n server. Each clien t attemp ting to access the network is uniq uely identified by the system throug h th e client’s MAC address .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches authen tication priority authentication priority To specify the prio rity of authenticatio n method s o n an interface, use the authentication priority co mmand in interface con figuratio n mo de. To retu rn to the d efau lt settings, use the no form of this co mmand . authentication priority method1 [method2] [method3] no authentication priority Syntax Description method1 Authentication method to be attempted .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches authentication priority Examples The following example shows how to specify the priority in which authenticatio n metho ds should be attempted for a client on an interface: Switch(config-if)# authentication priority mab dot1x webauth Switch(config-if)# Related Commands Command authentication order show authentication Descriptio n Specifies th e order in which auth entication meth ods sho uld be attempted for a client on an in terface
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches authentication timer authentication timer To con figure the authentication timer, use the authentication timer command in interface configuration mode. To return to the default s etting s, use the no fo rm of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches authentication timer Examples The fo llowing example shows how to sp ecify that the reauthenticatio n perio d value fo r th e client sho uld b e obtained from the authentication, authorization, and accou nting (AAA) server as Session-Timeo ut (RADIUS Attribute 2 7): Switch(config-if)# authentication timer reauthenticate server Switch(config-if)# Related Commands Command show authentication Descriptio n Displays Authenticatio n Manage
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches auth entication violation authentication violation Use the authentication vio lation interface configuration command to con figure the violation mode: restrict, shutdown, and replace. In single-ho st mode, a security violation is trigg ered when mo re than on e d evice are d etected on the data vlan. In multidomain auth entication mode, a security vio lation is trig gered when more than o ne device are detected on the d ata or voice VLAN.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches authentication violation Command Descriptio n authentication fallback authentication host-mode authentication open Con figures a p ort to use web authentication as a fallback method for clients th at do not supp ort IEEE 80 2.1x auth entication. Sets th e authorization manager mode on a port. Enab les or disab les open acces s o n a port. authentication order Sets th e order of authentication method s u sed on a port.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches auto qos classify auto qos classify To gen erate a QoS configuration for an untrusted interface, use the auto qos classify interface comman d. auto qos cla ssify Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings. Command Modes Interface con figuration mode Usage Guidelines This comman d gen erates a QoS configuration for untrusted interfaces .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches auto qos classify permit tcp any any eq 3689 permit udp any any eq 3689 permit tcp any any range 6881 6999 permit tcp any any eq 11999 permit tcp any any range 28800 29100 ip access-list extended AutoQos-4.0-ACL-Default permit ip any any class-map match-any AutoQos-4.0-VoIP-Data match dscp ef match cos 5 class-map match-all AutoQos-4.0-VoIP-Data-Cos match cos 5 class-map match-any AutoQos-4.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches auto qos classify class AutoQos-4.0-Default-Classify set dscp default set cos 0 C. Template for egress q ueu e classes along with th e SRND4 output policy that uses th e egress classes to allo cate 8 queues. This template is requ ired by all SRND4 commands: class-map match-all AutoQos-4.0-Priority-Queue match qos-group 32 class-map match-all AutoQos-4.0-Control-Mgmt-Queue match qos-group 16 class-map match-all AutoQos-4.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches auto qos classify Examples This example shows how to generate a QoS con figuratio n for the u ntrus ted interface gigabitethernet1/1: Switch(config)# interface gigabitethernet1/1 Switch(config-if)# auto qos classify Related Commands Command auto qos trust a uto qo s v oip cisco-so ftphone Descriptio n Gen erate QoS co nfigu rations fo r trus ted interfaces.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches auto qos classify police auto qos classify police To po lice traffic form an untrusted interface, use th e auto qos classify police interface command. auto qos cla ssify police Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings. Command Modes Usage Guidelines Interface con figuration mode This comman d gen erates a QoS configuration for untrusted interfaces .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches auto qos classify police permit tcp any any eq 1630 permit udp any any eq 1630 ip access-list extended AutoQos-4.0-ACL-Bulk-Data permit tcp any any eq ftp permit tcp any any eq ftp-data permit tcp any any eq 22 permit tcp any any eq smtp permit tcp any any eq 465 permit tcp any any eq 143 permit tcp any any eq 993 permit tcp any any eq pop3 permit tcp any any eq 995 permit tcp any any eq 1914 ip access-list extended AutoQos-4.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches auto qos classify police set cos 4 set qos-group 34 police cir 5000000 bc 8000 exceed-action drop class AutoQos-4.0-Signaling-Classify set dscp cs3 set cos 3 set qos-group 16 police cir 32000 bc 8000 exceed-action drop class AutoQos-4.0-Transaction-Classify set dscp af21 set cos 2 set qos-group 18 police cir 10000000 bc 8000 exceed-action set-dscp-transmit cs1 exceed-action set-cos-transmit 1 class AutoQos-4.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches auto qos classify police th eir o riginal qos-gro up classification because qos-grou ps canno t be remarked as an exceed actio n. However, becau se AutoQos-4 .0 -Scavenger-Queue is defined b efore all other queues in the ou tput po licy map, remarked p ackets fall into it, des pite retaining their original q os-g rou p labels. policy-map AutoQos-4.0-Output-Policye bandwidth remaining percent 1 class AutoQos-4.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches auto qos srnd4 auto qos srnd4 To generate QoS config urations based on so lution reference network design 4.0 , use the auto qos srnd4 global command. auto qos srnd4 Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings. Command Modes Glob al co nfigu ration Usage Guidelines This comman d is generated when any n ew auto-QoS co mmand is configu red on an in terface.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches auto qos srnd4 class-map match-all AutoQos-4.0-Internetwork-Ctrl match dscp cs6 class-map match-any AutoQos-4.0-Signaling match dscp cs3 match cos 3 class-map match-all AutoQos-4.0-Network-Mgmt match dscp cs2 class-map match-any AutoQos-4.0-Multimedia-Conf match dscp af41 match dscp af42 match dscp af43 class-map match-any AutoQos-4.0-Multimedia-Stream match dscp af31 match dscp af32 match dscp af33 class-map match-any AutoQos-4.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches auto qos srnd4 match qos-group 34 class-map match-all AutoQos-4.0-Multimedia-Stream-Queue match qos-group 26 class-map match-all AutoQos-4.0-Trans-Data-Queue match qos-group 18 class-map match-all AutoQos-4.0-Bulk-Data-Queue match qos-group 10 class-map match-any AutoQos-4.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches auto qos srnd4 Fo r interfaces with auto qos voip cisco-phone enabled —Glo ba l Level Commands Generated The glo bal templates defined in A an d B (above). —Interface Level Comma nds Genera ted For Fa/Gig Ports: Switch(config-if)# no qos trust device cisco-phone no service-policy input AutoQos-VoIP-Input-Cos-Policy no service-policy output AutoQos-VoIP-Output-Policy qos trust device cisco-phone service-policy input AutoQos-4.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches auto qos tru st auto qos trust To generate QoS configuration s for trusted interfaces, use th e auto qos trust interface command. auto qos trust Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches auto qos trust match dscp cs2 class-map match-any AutoQos-4.0-Multimedia-Conf match dscp af41 match dscp af42 match dscp af43 class-map match-any AutoQos-4.0-Multimedia-Stream match dscp af31 match dscp af32 match dscp af33 class-map match-any AutoQos-4.0-Transaction-Data match dscp af21 match dscp af22 match dscp af23 class-map match-any AutoQos-4.0-Bulk-Data match dscp af11 match dscp af12 match dscp af13 class-map match-all AutoQos-4.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches auto qos tru st match qos-group 10 class-map match-any AutoQos-4.0-Scavenger-Queue match qos-group 8 match dscp cs1 Because police comman ds execu ted in policy map configuration mod e do not allow the remarking of qos-gro ups fo r traffic flows that exceed defined rate limits, AutoQo s-4.0-Scaven ger-Queue must be co nfigured to match either qo s-group 7 or dscp af11.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches auto qos trust Command Descriptio n a uto qo s classify auto qos s rnd4 Gen erates a QoS configuration for an untrusted in terface. Gen erates QoS configu rations based o n s olution referen ce n etwo rk design 4.0. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches auto qos video auto qos video To generate QOS con figuratio n for cisco-telepresence or cisco-camera interfaces (conditio nal trust thro ugh CDP), use the auto qos video interface config uration comman d. auto qos video { cts | ip-camera } Syntax Description cts ip-camera Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches auto qos video class-map match-all AutoQos-4.0-Network-Ctrl match dscp cs7 class-map match-all AutoQos-4.0-Internetwork-Ctrl match dscp cs6 class-map match-any AutoQos-4.0-Signaling match dscp cs3 match cos 3 class-map match-all AutoQos-4.0-Network-Mgmt match dscp cs2 class-map match-any AutoQos-4.0-Multimedia-Conf match dscp af41 match dscp af42 match dscp af43 class-map match-any AutoQos-4.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches auto qos video match qos-group 16 class-map match-all AutoQos-4.0-Multimedia-Conf-Queue match qos-group 34 class-map match-all AutoQos-4.0-Multimedia-Stream-Queue match qos-group 26 class-map match-all AutoQos-4.0-Trans-Data-Queue match qos-group 18 class-map match-all AutoQos-4.0-Bulk-Data-Queue match qos-group 10 class-map match-any AutoQos-4.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches auto qos video end This example s hows how to generate QoS configuration for the cisco-camera in terface g igab itethern et1/1 : Switch(config)# interface gigabitethernet1/1 Switch(config-if)# auto qos video ip-camera Switch(config-if)# do sh running interface interface-id interface interface-id auto qos video ip-camera qos trust device ip-camera service-policy input AutoQos-4.0-Input-Policy service-policy output AutoQos-4.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches auto qos voip auto qos voip To au tomatically config ure qu ality of service (auto-QoS) fo r vo ice over IP (VoIP) with in a Qo S domain, use the a uto qos voip interface configuration comman d. To change the auto-QoS con figuratio n settings to the standard QoS d efaults , use the no form of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches auto qos voip To display the QoS configuration that is auto matically generated when au to-QoS is enabled , enab le d ebug ging (b efore you enable auto-QoS) with th e debug auto qos privileged EXEC command. To disab le au to-QoS on an interface, use th e no auto qos voip in terface con figuratio n command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches auto qos voip cisco-softphone auto qos voip cisco-softphone To generate QoS configuration for interfaces co nnected to PCs running the Cisco IP SoftPh one ap plication and mark police traffic coming from such interfaces, use the auto qos vo ip interface co nfiguration co mmand . auto qos voip cisco-softphone Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches auto qos voip cisco-softphone ip access-list extended AutoQos-4.0-ACL-Bulk-Data permit tcp any any eq ftp permit tcp any any eq ftp-data permit tcp any any eq 22 permit tcp any any eq smtp permit tcp any any eq 465 permit tcp any any eq 143 permit tcp any any eq 993 permit tcp any any eq pop3 permit tcp any any eq 995 permit tcp any any eq 1914 ip access-list extended AutoQos-4.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches auto qos voip cisco-softphone set qos-group 32 police cir 128000 bc 8000 exceed-action set-dscp-transmit cs1 exceed-action set-cos-transmit 1 class AutoQos-4.0-VoIP-Signal set dscp cs3 set cos 3 set qos-group 16 police cir 32000 bc 8000 exceed-action set-dscp-transmit cs1 exceed-action set-cos-transmit 1 class AutoQos-4.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches auto qos voip cisco-softphone match dscp cs1 Because the police commands executed in po licy map configuration mo de do no t allow remarkin g o f q os-g roup s for traffic flows that exceed defined rate limits, Auto Qos-4.0-Scavenger-Queue must be configured to match either qos-group 7 or dscp af11 .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches auto qos voip cisco-softphone Related Commands Co mmand auto qos voip cisco-softphone Description Generate QoS configuration for interfaces con nected to PCs run ning the Cisco IP SoftPho ne application and marks po lice traffic co ming from such in terfaces. auto qos cla ssify auto qos cla ssify police Generate a QoS con figuratio n for an untrusted interface. Police traffic form an un trusted interface.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches auto-sync auto-sync To enable automatic synchro nization o f the configu ration files in NVRAM , us e the auto-sync co mmand . To disable automatic syn chronization, u se the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches band width bandwidth To specify or modify the min imu m bandwidth p rovid ed to a class b elon ging to a po licy map attached to a phy sical p ort, use the bandwidth policy-map class co mmand . To return to th e default setting , use th e no form o f this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches bandwidth Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# policy-map polmap6 Switch(config-pmap)# class silver-class Switch(config-pmap-c)# bandwidth 2000 Switch(config-pmap-c)# end This example s hows how to guarantee 3 0 p ercent of th e bandwidth for class 1 and 25 percent of the b and width fo r class2 when CBWFQ is configured .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches band width Co mmand Description priority Enables th e strict priority qu eue (low-laten cy queueing [LLQ]) an d to give priority to a class o f traffic belong ing to a policy map attached to a physical po rt. Creates a serv ice policy that is a quality of serv ice (QoS) policy within a policy map. Enables traffic sh apin g a class o f traffic in a p olicy map attached to a phy sical port. Displays information about the policy map.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches call-home (global configuration) call-home (global configuration) To en ter call h ome config uration submo de, use th e call-home command in global configuration mo de. call-ho me Syntax Description This command has no arguments or keywo rds. Command Default This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches call-home (global configura tion) Examples • site-id alph anumeric—Specifies the site identificatio n for Cisco Au to Notify. You can enter up to 256 alphanumeric characters. If yo u in clud e spaces, you must enclo se you r en try in quo tes (“ ”). • street-address street-a ddress —Sp ecifies the street ad dress fo r the RMA p art sh ipmen ts. Yo u can en ter u p to 2 56 alph an umeric characters.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches call-home (global configuration) Related Commands Command a lert-group (refer to Cisco IOS documentatio n) profile (refer to Cisco IOS d ocu mentation) show call-ho me Descriptio n Enab les an alert group. Enters call-home profile co nfigu ration mode. Displays call home configuration information . Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches call-home reque st call-home request To sub mit information abou t yo ur system to Cis co for repo rt an d analysis information from the Cisco Outp ut Interpreter to ol, us e the call-home request comman d in p rivileged EXEC mode. An analysis report is sent by Cisco to a con figured contact e-mail ad dress.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches call-home request Related Commands call-ho me (global configura tion) call-ho me s end call-ho me s end a lert-group Enters call home con figuratio n mo de. Sends a CLI co mmand to be executed , with the co mmand outp ut to b e sent by e-mail. Sends a sp ecific alert group messag e. service ca ll-home (refer to Cisco IOS documentatio n) Enables or disables Call Home. show call-ho me Displays call-home configuration information .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches call-home send call-home send To execute a CLI command an d e-mail the command outpu t, use the call-home send command in privileged EXEC mod e. ca ll-home send “cli-command ” { ema il ema il-add r [service-number SR] | service-number SR} Syntax Description “cli-command ” email email-addr service-number SR Command Default Command Modes Usage Guidelines Specifies a CLI command to be executed. The command outpu t is sent by e-mail.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches call-home send alert-group call-home send alert-group To sen d a specific alert grou p message, us e the call-home s end alert-group comman d in p rivileg ed EXEC mode. call-ho me s end a lert-group {configuration | dia gnostic module nu mber | inventory} [pro file p rofile-na me] Syntax Description Command Default configuration diagnos tic module n umber Sends the configuration alert-gro up message to th e destination profile.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches call-home send alert-group service call-home (refer to Cisco IOS do cumentation) Enables or disables Call Home. show ca ll-home Disp lays call-home con figuratio n information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches call-home test call-home test To manually send a Call Ho me test mess age, use the call-home test command in privileged EXEC mo de. call-ho me test [“test-message”] profile p rofile-na me Syntax Description “test-message” profile p rofile-na me Command Default This command has no default setting s. (Optio nal) Test message text. Specifies the name of th e destination pro file.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches chann el-group channel-group To assign and co nfigure an EtherCh ann el interface to an EtherChannel group, u se the channel-group co mmand . To remove a channel gro up config uration from an interface, u se th e no form of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches channel-group Caution Examples Do not en able Layer 3 add resses o n th e phys ical EtherChannel in terfaces. Do not assign bridge group s o n th e phys ical EtherChannel interfaces because it creates loo ps.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches channel-protocol channel-protocol To enable LACP or PAgP on an interface, use the channel-protocol command. To disable the p roto cols, use th e no form o f this co mmand . channel-protocol {lacp | pagp} no channel-protocol { lacp | pagp} Syntax Description lacp pagp Enables LACP to manag e chan nelin g. Enables PAgP to manage channeling.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches channel-protocol Related Commands Command channel-group show etherchannel Descriptio n Assigns and co nfigu res an Eth erChan nel interface to an EtherChannel g rou p. Displays EtherChannel info rmation fo r a channel. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches cisp enable cisp enable Use the cisp enable global co nfigu ration co mmand to enable Client Information Signalling Proto col (CISP) o n a switch. cisp enable no cisp enable Syntax Description cisp ena ble Defaults Non e Command Modes Glob al co nfigu ration Usage Guidelines You mu st en able the CISP protocol (with the global cisp enable command) on b oth the au thenticator an d supplicant switch.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches class class To specify the name o f the class whose traffic policy y ou want to create or chang e, use the clas s p olicy-map configuration command. To delete an existing class from a p olicy map, u se the no form of th is command. class cla ss-n ame no class class-n ame Syntax Description Defaults class-name Name o f the p redefined traffic class fo r which you want to configu re o r modify a traffic po licy.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches class • service-policy (policy-map class) Creates a service p olicy as a quality of serv ice (QoS) policy within a policy map (called a h ierarchical service policy). For more information, see the service-policy (policy-map class) command. This command is effective on ly in a hierarchical policy map attached to an interface.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches class Related Commands Command bandwidth class-ma p dbl police Descriptio n Specifies or modifies the minimum b and width prov ided to a class b elon ging to a policy map attached to a phy sical port. Creates a class map to be used for matching packets to the class whose name you specify and to enter class-map co nfiguration mo de. Enab les active qu eue managemen t on a tran smit qu eue used by a class o f traffic.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches class-map class-map To create a class map to be us ed fo r matching packets to the class wh ose name you specify and to enter class-map config uration mode, use th e cla ss-map g lobal config uration command . To delete an existing class map and to return to global con figuratio n mo de, use th e no form of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches class-map This example s hows how to delete the class1 class map: Switch# configure terminal Switch(config)# no class-map class1 Switch# You can verify your settings by entering the show cla ss-map p rivileged EXEC command . Related Commands Command Descriptio n class Specifies the name of th e class wh ose traffic p olicy you want to create or change. Defines th e match criteria for a class map.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches clear counters clear counters To clear the interface counters, use the clea r counters co mmand . clear counters [{FastEthernet interface_nu mber} | {GigabitEthernet interface_ numb er } | {null interface_n umber} | {port-channel number } | {vla n vlan_id}] Syntax Description Defaults FastEthernet in terfa ce_number (Optional) Specifies the Fast Ethernet interface; valid values are fro m 1 to 9.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches clear errdisable clear errdisable To re-enable error-disabled VLANs on an interface, use th e clear errdisa ble co mmand . clear errdisable interface { n ame} vlan [range] Syntax Description interfa ce name Specifies the interface of the VLAN(s) to recover. v lan ran ge Specifies all VLANs o n th e interface b e recovered. (Optional) Specifies the VLAN range to be recovered. Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches cle ar hw-module slot password clear hw-module slot password To clear the password on an intellig ent line modu le, u se the clear hw-module slo t pa ssword comman d. clear hw-module slot slo t_num password Syntax Description slot_nu m Defaults The pas sword is no t cleared . Slo t o n a line mod ule. Command Modes Privileg ed EXEC mode Usage Guidelines You on ly n eed to ch ang e the p assword o nce unless the passwo rd is reset.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches clear interface gigabitethernet clear interface gigabitethernet To clear the h ardware logic from a Gigabit Ethern et IEEE 802 .3 z interface, use the clea r interface g igabitethernet co mmand . Note This command do es not increment interface resets as dis play ed with th e show interface g igabitethernet mo d/port command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches clear interface vlan clear interface vlan To clear the hardware log ic from a VLAN, use the clea r interface vla n comman d. clear interface vlan numb er Syntax Description number Defaults This comman d has no default settings. Numb er o f the VLAN interface; valid values are from 1 to 4094 .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches clear ip access-template clear ip access-template To clear the statistical information in access lists , use the clea r ip access -template command . clear ip access-template access-list Syntax Description a cces s-list Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches clear ip arp inspection log clear ip arp inspection log To clear the statu s o f the lo g bu ffer, use the clear ip arp inspection log command. clear ip arp inspection log Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches clear ip arp inspection statistics clear ip arp inspection statistics To clear the d ynamic ARP inspectio n s tatistics, us e the clear ip arp inspection sta tistics command. clear ip arp ins pection sta tistics [vlan vlan-range] Syntax Description v lan vlan-range Defaults This command has no default setting s. Command Modes Examples (Optional) Specifies the VLAN range.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches clear ip dhcp snoop ing binding clear ip dhcp snooping binding To clear the DHCP snoo ping bindin g, us e the clear ip dhcp snooping binding co mmand . clear ip dhcp snooping binding [*] [ip-ad dress ] [vlan vlan_nu m] [interface interface_ num] Syntax Description Defaults Command Modes Usage Guidelines * ip-a ddress (Op tional) Clears all DHCP snoop ing binding entries.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches clear ip dhcp snooping binding Related Commands Command ip dhcp snooping Descriptio n Globally enables DHCP snoo ping. ip dhcp snooping binding Sets up and g enerates a DHCP bind ing co nfiguration to restore binding s across reb oots. ip dhcp snoo ping informa tion option Enab les DHCP op tion 82 data insertio n. ip dhcp snooping trust ip dhcp snoo ping vlan show ip dhcp s noo ping Enab les DHCP sn ooping on a trusted VLAN.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches clear ip dh cp snooping database clear ip dhcp snooping database To clear the DHCP bind in g database, use the clea r ip dhcp snooping da tabase command . clear ip dhcp snooping database Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches clear ip dhcp snooping database statistics clear ip dhcp snooping database statistics To clear the DHCP binding databas e statistics, use th e clear ip dhcp snooping database statistics command. clear ip dhcp snooping databas e sta tistics Syntax Description This command has no arguments or keywo rds. Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches clear ip igmp group clear ip igmp group To delete the IGMP group cache entries, use th e clear ip igmp g roup command. clear ip igmp group [{fas tethernet mod /port} | {GigabitEthernet mo d/port } | {host_ name | group_a ddress } {Loopback interface_number} | {null interface_number} | {port-channel number } | {vla n vlan_id }] Syntax Description fas tethernet mod /port (Optional) Specifies the Fast Ethernet interface.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches clear ip igmp group This example s hows how to clear the IGMP group cache entries fro m a specific interface: Switch# clear ip igmp group gigabitethernet 2/2 Switch# Related Commands Command ip host (refer to Cisco IOS d ocu mentation) show ip igmp groups (refer to Cis co IOS d ocu mentation) show ip igmp interface Descriptio n Defines a static host name-to-add ress mapp ing in the hos t cache.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches clea r ip igmp snooping membership clear ip igmp snooping membership To clear the exp licit host-tracking datab ase, u se the clear ip igmp snooping membership command. clear ip igmp snooping memb ership [v lan vlan_id] Syntax Description vlan vlan _id Defaults This comman d has no default settings. Command Modes Usage Guidelines Examples (Optional) Sp ecifies a VLAN; valid values are from 1 to 10 01 and fro m 1006 to 409 4.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches clear ip mfib counters clear ip mfib counters To clear the g lobal MFIB counters and the cou nters for all active MFIB routes, u se the clear ip mfib counters command. clear ip mfib co unters Syntax Description This command has no arguments or keywo rds. Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches c lear ip mfib fastdrop clear ip mfib fastdrop To clear all the MFIB fast-dro p entries , use the clea r ip mfib fastdrop co mmand . clear ip mfib fastdrop Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings. Command Modes Usage Guidelines Examples Privileg ed EXEC mode If new fast-dropped packets arrive, the new fas t-drop entries are created .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches clear ip wccp clear ip wccp To remove Web Cache Commu nication Pro toco l (WCCP) statistics (co unts) maintained o n th e switch for a particular service, use the clear ip wccp command in privileged EXEC mode. clear ip wccp [vrf vrf-name {web-cache | s ervice-number}] [web-cache | service-nu mber] Syntax Description web-ca che (Optio nal) Directs the router to remove statistics for th e web cache service.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches clear lacp counters clear lacp counters To clear the statis tics fo r all the interfaces belong in g to a specific chan nel group, use th e clear lacp co unters co mmand . clear lacp [chann el-group] counters Syntax Description cha nnel-group Defaults This comman d has no default settings. (Optio nal) Ch ann el-group number; valid values are fro m 1 to 64.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches clear mac-address-table clear mac-address-table To clear the g lobal counter entries from the Lay er 2 M AC address table, use the clea r mac-address-table command . clear ma c-address-table {dynamic [{address mac_ addr } | {interfa ce interface}] [vlan vlan_ id] | notification} Syntax Description Defaults dynamic a ddress ma c_a ddr Specifies dynamic entry ty pes . (Optional) Specifies the MAC address .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches clear mac-address-table Related Commands Co mmand clear mac-a ddress-ta ble dy na mic mac-addres s-table aging-time Description Clears the dynamic address entries from th e Layer 2 MAC ad dress tab le. Config ures the aging time for entries in the Lay er 2 table. mac-addres s-table notification Enables M AC address no tification on a switch.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches clear mac-address-table dynamic clear mac-address-table dynamic To clear the d ynamic address entries from the Layer 2 MAC ad dress tab le, use the clear mac-address-table dynamic command. clear mac-address-table dynamic [{address mac_addr} | {interface interface}] [v la n vlan_id ] Syntax Description a ddress ma c_a ddr interfa ce interfa ce (Optional) Specifies the MAC address .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches clear nmsp statistics clear nmsp statistics To clear the Network Mobility Services Pro toco l (NMSP) statistics , use the clea r nmsp sta tistics co mmand . This command is available only wh en you r switch is run ning the cry ptograp hic (en crypted) software image. clear nmsp statistics Syntax Description This comman d has no argu ments or keyword s. Defaults No default is defined.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches clear pagp clear pagp To clear the p ort-ch ann el information, use th e clear pa gp command. clear pagp {group-number | counters } Syntax Description g rou p-n umber counters Defaults This command has no default setting s. Channel-gro up number; valid values are from 1 to 64. Clears traffic filters.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches c lear port-sec urity clear port-security To delete all co nfigu red s ecure ad dresses o r a specific dynamic or sticky secu re addres s on an interface from the MAC ad dress table, use th e clear po rt-security command. clear port-security dynamic [addres s mac-addr [vlan vla n-id]] | [interface interface-id] [vlan access | voice] Syntax Description dynamic address mac-ad dr Deletes all the dynamic secure MAC addres ses.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches clear port-security Related Commands Command show port-security Descriptio n Displays info rmation ab out the po rt-security setting . switchport po rt-security Enab les port security on an interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches clear pppoe intermediate-agent statistics clear pppoe intermediate-agent statistics To clear PPPoE Intermediate Ag en t statistics (packet counters), use the clear pppoe intermediate-agent sta tistics command. clear ppoe intermediate-agent statistics Syntax Description This comman d has no argu ments . Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches clear qos clear qos To clear the g lobal and per-interface aggregate QoS counters, use the clear qos co mmand . clear qos [a ggregate-policer [na me] | interface {{fastethernet | GigabitEthernet} {mod/interface}} | vlan {vla n_num} | port-channel {numb er }] Syntax Description a ggregate-policer name interfa ce fastethernet (Optional) Specifies an agg regate policer. (Optional) Specifies an interface.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches clear vlan counters clear vlan counters To clear the software-cached co unter values to start from zero again for a sp ecified VLAN or all existing VLANs, use th e clear vlan counters command. clear vlan [vlan-id ] co unters Syntax Description vla n-id Defaults This comman d has no default settings. (Optional) VLAN n umber; see the “Usage Guidelines” section for valid values .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches clear vmps statistics clear vmps statistics To clear the VMPS statistics , use the clea r vmps statis tics command. clear vmps statistics Syntax Description This command has no arguments or keywo rds. Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches control-plane control-plane To enter co ntro l-plane configuration mo de, which allows users to ass ociate o r modify attributes or parameters (such as a service policy) that are associated with the con trol plane o f the d evice, use th e co ntro l-plane comman d. co ntro l-plane Syntax Description This comman d has no argu ments or keyword s. Defaults Default service po lice system-cp p-p olicy is attach ed.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches control-plane Related Commands Command class class-ma p match access-group (refer to th e Cisco IOS Release 1 2.2 Comman d Referen ce) Descriptio n Specifies the name of th e class wh ose traffic p olicy you want to create or change. Creates a class map to be used for matching packets to the class whose name you specify and to enter class-map co nfiguration mo de.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches c ounter counter To assign counters to a Lay er 3 interface, u se the counter in terface co mmand . To remo ve a counter ass ignment, use the no fo rm of this command. co unter {ipv 4 | ipv6 | ipv4 ipv6 sepa rate} no counter Syntax Description Defaults ipv 4 ipv 6 Enables collectio n of IPv4 statistics o nly. Enables collectio n of IPv6 statistics o nly.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches counte r If you have already assigned the maximum n umber of counters, the counter command fails, disp layin g th e fo llowing error message: Switch# config terminal Enter configuration commands, one per line. End with CNTL/Z.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches dbl dbl To enable active queue manag ement on a transmit queue used by a class of traffic, u se th e dbl comman d. Use the no form of this comman d to return to the defau lt setting. dbl no dbl Syntax Description This comman d has no keywo rds or arg umen ts. Defaults Active queue managemen t is disabled.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug adjacency debug adjacency To display in formatio n abou t the adjacency debu gging, use the debug adjacency co mmand . To disable d ebug ging outpu t, use the no form of this comman d. debug adja cency [ipc] no debug adjacency Syntax Description ipc Defaults This command has no default setting s. Command Modes Priv ileged EXEC mo de Examples (Optio nal) Displays the IPC entries in the adjacency database.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches debug backup debug backup To debug th e backu p events , use the debug backup co mmand . To disable the debugg ing o utput, use the no form o f this co mmand . debug backup no debug backup Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug condition interface debug condition interface To limit th e debugging o utput of interface-related activities , use the debug co nditio n interface command. To disable th e debugging o utput, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches debug condition standby debug condition standby To limit the debuggin g output for th e standby state ch ang es, use the debug condition standby command. To disable the debuggin g output, use th e no form o f this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug condition standby This example s hows the d isplay if you try to turn off th e last standby d ebug cond itio n: Switch# no debug condition standby vlan 1 0 This condition is the last standby condition set. Removing all conditions may cause a flood of debugging messages to result, unless specific debugging flags are first removed.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches debug condition vlan debug condition vlan To limit the VLAN debugg ing ou tput for a specific VLAN, u se the debug condition vlan co mmand . To disable the debugging ou tput, u se the no form of th is command. debug condition vlan {vlan _id} no debug condition vlan {vlan_ id} Syntax Description vla n_id Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug condition vlan Related Commands Command undebug condition vlan (same as no debug co ndition vlan) Descriptio n Disab les debuggin g output. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches deb ug dot1x debug dot1x To enable the debu gging for the 802.1X feature, use th e debug dot1x comman d. To disable the debugging ou tput, u se the no form of this command. debug dot1x {all | erro rs | ev ents | packets | reg is try | state-machine} no debug dot1x {all | errors | events | packets | registry | state-machine} Syntax Description all erro rs Enables the debugg ing of all conditions.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug etherchnl debug etherchnl To debug EtherChannel, u se the debug etherchnl comman d. To disable the debu gging outp ut, use the no form of th is command. debug etherchnl [a ll | detail | erro r | event | idb | linecard] no debug etherchnl Syntax Description Defaults a ll detail (Optional) Display s all EtherChannel debug mess ages. (Optional) Display s th e detailed EtherCh ann el debug messag es.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches debug etherchnl Related Commands Co mmand Description undebug etherchnl (same as n o Disables d ebug ging outp ut. debug etherchn l) Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug interface debug interface To abbreviate the entry of the debug condition interface co mmand , u se the debug interface command. To disable debugg ing output, use th e no form of this command .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches debug ipc debug ipc To d ebu g the IPC activity, us e the debug ipc command. To disable th e d ebug ging ou tput, use the no form of this command. debug ipc {a ll | errors | events | headers | packets | ports | seats } no debug ipc {all | errors | events | headers | pa ckets | ports | s eats} Syntax Description all erro rs Enables all IPC d ebug ging. Enables the IPC error debu gging. events headers Enables the IPC event d ebu gging.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug ip dhcp snooping event debug ip dhcp snooping event To debug the DHCP sn ooping even ts, use the debug ip dhcp snooping event command. To dis able d ebug ging outpu t, use the no form of this comman d. debug ip dhcp snooping event no debug ip dhcp snooping event Syntax Description This command has no arguments or keywo rds. Defaults Debu gging of s noopin g event is disabled.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches debug ip dhcp snooping packet debug ip dhcp snooping packet To debug th e DHCP s nooping messag es, u se the debug ip dhcp sno oping packet co mmand . To disable the debugg ing outpu t, use th e no form of this comman d. debug ip dhcp snooping packet no debug ip dhcp snooping packet Syntax Description This comman d has no argu ments or keyword s. Defaults Debuggin g o f snoo ping packet is d isab led.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug ip verify source packet debug ip verify source packet To debug the IP sou rce gu ard messages, u se the debug ip verify source packet comman d. To disab le th e debugging o utput, u se the no form of this command. debug ip verify source pa cket no debug ip verify source packet Syntax Description This command has no arguments or keywo rds. Defaults Debu gging of s noopin g s ecurity p ackets is disabled.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches debug lacp debug lacp To debug the LACP activity, use th e debug lacp comman d. To disable th e debu gging outpu t, use the no form of this comman d. debug lacp [all | event | fsm | misc | pa cket] no debug lacp Syntax Description all event (Optional) En ables all LACP debugging . (Optional) En ables the d ebug ging of the LACP even ts. fsm misc (Optional) En ables the d ebug ging of the LACP finite state mach ine.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug monitor debug monitor To display th e monitoring activity, use th e debug monitor co mmand . To disable th e debuggin g o utput, u se the no form of th is command. debug monitor {a ll | errors | idb-update | list | notifications | platform | requests} no debug monitor {all | errors | idb-update | list | notifications | platform | requests} Syntax Description a ll errors Displays all the SPAN debu gging messag es.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches debug nmsp debug nmsp To the enable debu gging of the Netwo rk Mob ility Services Protocol (NMSP) o n the switch, use th e debug nmsp command. This command is available only when your switch is running the cry ptograp hic (encrypted) software image. Use the no form of th is command to disable debugg ing.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug nvram debug nvram To debug the NVRAM activity, use the debug nvram command. To disable the debuggin g output, use th e no form o f this co mmand . debug nvram no debug nvram Syntax Description This command has no arguments or keywo rds. Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches debug pagp debug pagp To debug th e PAgP activ ity, use th e debug pagp command. To d isable the debugging outp ut, use the no form of this comman d. debug pagp [a ll | dual-active | event | fsm | misc | pa cket] no debug pagp Syntax Description all dual-active (Optional) En ables all PAg P debuggin g. (Optional) En ables the PAgP du al-active debugg ing. event fsm (Optional) En ables the d ebug ging of the PAgP events.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug platform packet protocol lacp debug platform packet protocol lacp To debug the LACP protocol p ackets, use the debug platform pa cket protocol la cp co mmand. To d isable the debugg ing outpu t, use the no form of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches debug platform packet protocol pagp debug platform packet protocol pagp To debug the PAgP p roto col packets, use th e debug platform packet proto col pagp co mmand. To disable the debugging ou tput, u se the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug pm debug pm To debug the port man ager (PM) activity, u se the debug pm command. To disable the debugging output, u se the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches debug port-sec urity debug port-security To debu g po rt security, use the debug port-security command. To disable the debuggin g outp ut, use the no form o f this co mmand . debug port-security no debug port-security Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug pppoe intermediate-agent debug pppoe intermediate-agent To turn o n d ebug ging of th e PPPoE Intermediate Ag ent feature, use the debug pppoe intermediate-agent co mmand . To turn off debu gging, use th e no form of this command .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches d ebug p ppoe intermediate-agent Related Commands Co mmand pppoe intermediate-agent (interface) pppoe intermediate-agent limit rate pppoe intermediate-agent trust Description Enables th e PPPoE Intermediate Ag en t feature on an interface. Limits the rate of the PPPoE Discovery p ackets arriving on an interface. Sets the trust configu ration of an interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug redundancy debug redundancy To debug sup ervisor en gine redundancy, use the debug redunda ncy command. To dis able the debu gging o utput, u se the no form of this command . debug redundancy {errors | fsm | kpa | msg | prog ression | status | timer} no debug redundancy Syntax Description errors fsm Enab les the redund ancy facility for error d ebug ging. Enab les the redund ancy facility for FSM event d ebu gging.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches debug spanning-tree debug spanning-tree To debug the sp ann ing tree activities, use the debug s panning-tree comman d. To disable the debugging outpu t, use th e no form of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug spanning-tree Related Commands Command undebug s panning-tree (same as n o d ebug sp ann ing-tree) Descriptio n Disab les debuggin g output. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches debug spanning-tree backbonefa st debug spanning-tree backbonefast To enable debugg ing of the span ning tree BackboneFast events, use th e debug s panning-tree backbonefast command. To disable th e debuggin g output, use the no form o f this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug spanning-tree switch debug spanning-tree switch To en able the switch sh im debugg ing, u se the debug spanning-tree switch command. To disable the d ebug ging outpu t, use the no form of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches debug spanning-tree switch Examples This examp le shows how to enable th e transmit BPDU debugg ing on the spann in g tree switch shim: Switch# debug spanning-tree switch tx Spanning Tree Switch Shim transmit bpdu debugging is on *Sep 30 08:47:33: SP: STP SW: TX: bpdu of type ieee-st size 92 on FastEthernet5/9 303 *Sep 30 08:47:33: SP: STP SW: TX: bpdu of type ieee-st size 92 on FastEthernet5/9 304 *Sep 30 08:47:33: SP: STP SW: TX: bpdu o
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug spanning-tree uplinkfast debug spanning-tree uplinkfast To en able the debugg ing of the spanning-tree UplinkFast even ts, use the debug spanning-tree uplinkfast command. To disable th e debuggin g o utput, use the no form of this command . debug spanning-tree uplinkfast [exceptions] no debug spanning-tree uplinkfast Syntax Description exceptions Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches debug sw-vlan debug sw-vlan To debug the VLAN man ager activ ities, use the debug sw-vlan command. To disable the debugging outpu t, use th e no form of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug sw-vlan ifs debug sw-vlan ifs To en able the VLAN manager Cisco IOS file s ystem (IFS) error tests, us e the debug sw-vlan ifs command. To disable th e debugging o utput, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches debug sw-vlan ifs Related Commands Co mmand undebug sw-vlan ifs (same as no debug sw-vlan ifs) Description Disables d ebug ging outp ut. Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug sw-vlan notification debug sw-vlan notification To enable th e debug ging of the mess ages that trace th e activ ation and deactivatio n of the ISL VLAN IDs, u se the debug sw-vlan notification command. To d isable the debugging outp ut, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches debug sw-vlan vtp debug sw-vlan vtp To en able th e debugging of messages to b e gen erated by th e VTP p roto col co de, u se the debug sw-vlan vtp comman d. To disab le the d ebu gging outp ut, use the no fo rm of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug udld debug udld To en able the debugg ing of UDLD activ ity, u se the debug udld command. To disable the debugging o utput, u se the no form of this command . debug udld {events | packets | regis tries } no debug udld {events | packets | registries} Syntax Description events packets reg istries Enab les the debu gging of UDLD process events as they occur.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches debug udld Related Commands Co mmand undebug udld (same as no debug udld) Description Disables d ebug ging outp ut. Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches debug vqpc debug vqpc To debug the VLAN Query Pro toco l (VQP), u se the debug vqpc command. To disable the debu gging o utput, u se the no form of this command . debug vqpc [all | cli | events | learn | packet] no debug vqpc [all | cli | events | learn | packet] Syntax Description a ll (Optio nal) Debugs all the VQP events. cli events learn (Optio nal) Debugs the VQP co mmand -line interface. (Optio nal) Debugs the VQP events.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches define interface-range define interface-range To create a macro of in terfaces, u se the define interfa ce-range command . define interface-range macro-name interface-range Syntax Description macro-n ame interface-range Defaults This comman d has no default settings. Command Modes Usage Guidelines Name of the in terface range macro ; u p to 3 2 characters.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches deny deny To deny an ARP packet based on match es again st th e DHCP bind ings, use the deny co mmand . To remo ve the s pecified ACEs from the access list, use the no fo rm of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches deny Usage Guidelines Examples Deny clauses can be added to fo rward o r drop ARP p ackets b ased on some matching criteria. This examp le shows a host with a MAC address of 0000.000 0.abcd and an IP address of 1.1.1 .1. This example shows howto d eny bo th requests and res ponses from this h ost: Switch(config)# arp access-list static-hosts Switch(config-arp-nacl)# deny ip host 1.1.1.1 mac host 0000.0000.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches destination address destination address To con figure the des tin ation e-mail add ress or URL to wh ich Call Ho me mes sages will be sent, u se the destination address command. destination address {email email-address | http url} Syntax Description email ema il-add ress http url Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches destination message-size-limit bytes destination message-size-limit bytes To config ure a maximum destinatio n message s ize for th e destination pro file, use the des tination message-size-limit bytes command. destina tion messag e-size-limit bytes Syntax Description This comman d has no argu ments or keyword s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches destination preferred-msg-format destination preferred-msg-format To co nfigure a preferred mes sage format, use the destination preferred-msg-format co mmand. destination preferred-msg-format {long-text | short-text | xml} Syntax Description long-text short-text Sends the message in lon g-text format. Sends the message in sh ort-text format. x ml Sends the message in XML fo rmat.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches destination transport-method destination transport-method To enable the message transport metho d, use the destination transport-method command. destination transport-method {email | http} Syntax Description email http Defaults e-mail Command Modes Usage Guidelines Examples Enables e-mail as tran sport method . Enables HTTP as transport method .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches diagnostic fpga soft-error recover diagnostic fpga soft-error recover To con figure the SEU beh avio r, u se the diagnostic fpg a s oft-error recover command. To return to the d efault setting, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches diagnostic monitor action diagnostic monitor action To direct the actio n of the s witch when it detects a p acket memory failu re, use the diagnostic monitor action co mmand . diagnostic monitor action [co nservative | normal | aggressive] Syntax Description co nservative (Optional) Specifies that th e bootu p SRAM diagno stics log all failu res and remove all affected buffers from the hard ware o peration.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches diagnostic start diagnostic start To run th e specified diagno stic test, use the diagnostic start comman d. diagnos tic start {module num} {test test-id} [port num] Syntax Description Defaults module num Mo dule n umber. test test-id Specifies a test to ru n. Specifies an identificatio n n umber fo r the test to be run; can be th e cable d iagn ostic test-id, or the ca ble-tdr keywo rd.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches dot1x auth-fail max-attemp ts dot1x auth-fail max-attempts To config ure the max number of attempts before a port is moved to th e auth-fail VLAN, use the dot1x a uth-fail max-attempts command. To return to the default setting, u se the no form of this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches dot1x auth-fail vlan dot1x auth-fail vlan To enable the auth-fail VLAN on a p ort, u se the dot1x auth-fail vlan command. To return to the default setting, use th e no form of this command . dot1x auth-fail vlan vlan-id no dot1x auth-fail vlan vlan -id Syntax Description vlan-id Defaults This command has no default setting s. Command Modes Interface configuration mode Examples Specifies a VLAN in the range of 1 to 4094 .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches dot1x control-direction dot1x control-direction To enable un idirectio nal po rt co ntrol on a per-po rt basis on a switch, use the dot1 x control-direction co mmand . Use the no fo rm of this command to disable unid irectio nal port co ntrol. dot1x control-direction [in | both] no dot1x control-direction Syntax Description in both Defaults Both in-b ound and out-bound traffic will be controlled .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches dot1x credentials (global configuration) dot1x credentials (global configuration) Use the dot1x credentials global con figuratio n command to configure a pro file on a sup plicant switch. dot1x credentia ls profile no dot1x credentials profile Syntax Description p rofile Defaults No pro file is config ured for the switch . Command Modes Global configuration Specify a pro file for the supplicant switch.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches dot1x critical dot1x critical To enab le the 802.1X critical authentication on a port, use the dot1x critical command. To return to the default setting , use the no form of this comman d. dot1x critical no dot1x critical Syntax Description This comman d has no keywo rds or variables. Defaults Critical authentication is disabled. Command Modes Interface con figuration mode Examples This examp le shows how to enable 8 02.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches dot1x critical eapol dot1x critical eapol To enable sending EAPOL s uccess packets when a port is critically authorized partway th rou gh an EAP exchange, u se th e dot1x critical eapol command. To return to th e d efault setting , u se the no form of this command. dot1x critica l eapol no dot1x critical ea po l Syntax Description This command has no key words or variables.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches dot1x critical recovery delay dot1x critical recovery delay To set the time interval between po rt reinitializations, u se the dot1x critical recovery delay co mmand . To return to the default setting, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches dot1x critical vlan dot1x critical vlan To ass ign a critically authenticated port to a specific VLAN, use th e dot1 x critical vlan command. To retu rn to the defau lt setting, use th e no form o f this co mmand . dot1x critica l vla n vlan-id no dot1x critical vla n-id Syntax Description vlan-id Defaults Critical auth entication is disab led on a ports VLAN.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches dot1x guest-vlan dot1x guest-vlan To enable a guest VLAN o n a per-p ort b asis, use the dot1 x guest-vlan comman d. To retu rn to the default settin g, use the no form of th is command. dot1x g uest-vlan vlan-id no dot1x guest-vlan vlan -id Syntax Description vla n-id Defaults This comman d has no default settings.; th e guest VLAN feature is disabled .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches dot1x guest-vlan supplicant dot1x guest-vlan supplicant To place an 8 02.1X-capable su pplicant (h ost) into a guest VLAN, use th e dot1x guest-vlan s upplica nt g lobal configuration command. To return to th e default settin g, use the no fo rm of this command. dot1x quest-vlan supplicant no dot1x quest-vlan supplicant Syntax Description This command has no arguments or keywo rds. Defaults 8 02.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches dot1x host-mode no dot1x host-mode [multi-ho st | single-host | multi-do main} Syntax Description multi-host single-host En ables multiple-h osts mode on th e switch. En ables single-h ost mode o n th e switch. multi-domain En ables MDA on a switch port . Defaults The defau lt is sing le-host mode. Command Modes Interface con figuration mode Usage Guidelines Use this command to limit an IEEE 80 2.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches dot1x host-mode Switch(config-if)# end Switch# You can verify your settings by entering the show dot1x [interface interface-id] p rivileg ed EXEC command. Related Commands Command show dot1x Descriptio n Displays dot1x information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches dot1x initialize dot1x initialize To un auth orize an interface befo re reinitializing 80 2.1 X, u se the do t1x initia lize command . dot1x initialize inter face Syntax Description interface Defaults This comman d has no default settings. Number of the interface. Command Modes Privileg ed EXEC mode Usage Guidelines Use this command to initialize state machines and to set up the enviro nmen t for fresh authentication.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches dot1x mac-auth-bypass dot1x mac-auth-bypass To enable th e 802.1X MAC ad dress bypassing on a switch, use the dot1x ma c-auth-by pa ss command. Use the no form of this command to disable M AC address byp assin g. dot1x ma c-auth-by pas s [eap] no dot1 x mac-a uth-bypass [eap] Syntax Description eap Defaults There is no default setting.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches dot1x max-re auth-req dot1x max-reauth-req To set th e maximum n umber of times that the s witch will retransmit an EAP-Request/Identity frame to the clien t b efore restarting the au then tication process, use the dot1x max-reauth-req command. To return to th e default settin g, use the no fo rm of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches dot1x max-req dot1x max-req To set the maximum number of times that th e switch retransmits an Extensib le Authenticatio n Protocol (EAP)-Request frame of typ es other than EAP-Req ues t/Identity to the clien t b efore restarting the authenticatio n p rocess, us e the dot1x ma x-req comman d. To return to the default s etting , use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches dot1x port-control dot1x port-control To enab le man ual contro l of th e auth orization state o n a p ort, u se the dot1x po rt-control command. To return to th e default settin g, use the no fo rm of this command. dot1x port-control { a uto | force-a uthorized | fo rce-una uthorized} no dot1x port-control {auto | force-authorized | force-unauthorized} Syntax Description auto force-a uthorized force-unauthorized En ables 802.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches dot1x port-control Examples This example s hows how to enab le 802 .1X on Gigabit Ethern et 1/1: Switch(config)# interface gigabitethernet1/1 Switch(config-if)# dot1x port-control auto Switch# You can verify your settin gs by u sing the show dot1x all o r show do t1x interface int commands to show th e port-control status . An enabled status indicates that the port-control value is set either to auto or to force-unauthorized.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches dot1x re-authenticate dot1x re-authenticate To manually initiate a reauthenticatio n of all 80 2.1 X-enabled ports or the specified 80 2.1X-en abled po rt, use th e dot1 x re-authenticate comman d. dot1x re-authenticate [interfa ce interfa ce-id] Syntax Description interface interface-id Defaults This comman d has no default settings. (Op tio nal) Module an d p ort numb er o f the in terface.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches dot1x re-authentication dot1x re-authentication To en able the periodic reauthenticatio n of the client, u se the dot1x re-authentica tion co mmand . To retu rn to the defau lt setting, use th e no form o f this co mmand . dot1x re-authentication no dot1x re-authentication Syntax Description This command has no arguments or keywo rds. Defaults The periodic reauthenticatio n is dis abled.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches dot1x system-auth-control dot1x system-auth-control To enable 80 2.1 X au then tication on the s witch, use the dot1x system-a uth-control co mmand. To disable 80 2.1 X au then tication on the s ystem, use th e no form of this comman d. dot1x system-auth-control no dot1x system-auth-control Syntax Description This comman d has no argu ments or keyword s. Defaults The 802.1X authentication is disabled.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches dot1x timeout dot1x timeout To set the reau th en tication timer, use th e dot1x timeout command. To return to the default setting, use th e no form o f this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches dot1x timeout Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# interface fastethernet4/3 Switch(config-if)# dot1x timeout tx-period 60 Switch(config-if)# end Switch# You can verify you r settin gs by entering the show dot1x privileged EXEC command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches duplex duplex To co nfigure th e duplex operation on an interface, use th e duplex command. To retu rn to the d efau lt setting, use th e no form of this command . duplex {auto | full | half} no duplex Syntax Description Defaults a uto full Specifies the au toneg otiatio n operation. Specifies the fu ll-dup lex operation . half Specifies the half-duplex operation.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches duplex If the transmission speed on a 16-port RJ-4 5 Gigab it Ethernet port is s et to 100 0, the du plex mode is set to full. If the transmission speed is changed to 10 or 10 0, the duplex mode stays at full. You must co nfigure the correct du plex mode on th e switch wh en the transmission speed ch ang es to 10 or 100 from 1000 Mb ps.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches epm access control epm access control To co nfigure access co ntro l, use th e epm access control [open | default] command. epm access control [open | default] Syntax Description o pen default Defaults If the epm access co ntro l comman d is no t config ured, th e behav io r defaults to the epm access control default command. Nothin g is nvgened. Command Modes Con figuratio n mode Usage Guidelines Specifies op en access con trol.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches erase erase To erase a file sy stem, use the erase co mmand . erase {/all [non-default | nvram:] | ca t40 00_flash | nvram: | startup-config} Syntax Description /all nvram: /all non-default Erases everything in nvram:. Erases files an d con figuratio n in n onvolatile storage inclu ding nvram:, bootflash :, cat40 00_flas h:, and crashinfo: o f the lo cal sup ervisor eng in e.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches erase • Cisco IOS Configuration Fundamen tals Co nfiguration Command Reference, Release 12 .2 , at this URL: h ttp://www.cisco.com/en/US/docs/ios/12 _2/config fun/command/reference/ffun_ r.html Caution Examples The erase /all non-default command can erase Cisco IOS images in bootflash :.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches erase Related Commands Co mmand boot config (refer to Cisco IOS documentatio n) delete (refer to Cis co IOS documentatio n) show bootv ar Description Specifies th e dev ice and filename of the configuration file. undelete (refer to Cisco IOS documentatio n) Recovers a file marked “d eleted ” on a Class a flash file system. Deletes a file from a flash memory d evice or NVRAM. Displays BOOT en viron ment variable info rmation.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches errdisable detect errdisable detect To en able erro r-d isab le detection, use th e errdisable detect command. To disable the error-disab le d etectio n feature, use the no fo rm of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches errdisable detect Examples This examp le shows how to enable error-disable detection for the link-flap error-disable cau se: Switch(config)# errdisable detect cause link-flap Switch(config)# This examp le shows how to enable p er-VLAN error-disable d etection for BPDU guard: Switch(config)# errdisable detect cause bpduguard shutdown vlan Switch(config)# This examp le shows how to d isable error-disab le detection for DAI: Switch(config)
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches errdisable recovery errdisable recovery To configure th e recovery mech anism variab les, us e th e errdisable recovery co mmand . To return to the d efault setting, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches errdisab le recovery Defaults Error disab le recovery is disabled . The recovery interval is set to 30 0 s econds . Command Modes Glob al co nfigu ration mode Usage Guidelines A cause (bpdugu ard, dtp-flap, link -flap , pag p-flap , udld) is d efined as the reason why the erro r-disab led state occurred.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches errdisable recovery Related Commands Command show errdisable detect Descriptio n Displays the error dis able detection statu s. show errdisable recovery show interfa ces sta tus Displays erro r disable recovery timer information. Displays the interface s tatus or a list of interfaces in error-disabled state. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches flowcontrol flowcontrol To configure a Gigabit Eth ernet interface to s end or receive pause frames, use the flowcontrol command. To disable the flow con trol setting, use the no form of this command. flowco ntro l {receiv e | send} {off | on | desired} no flowcontrol {receive | s end} { o ff | on | desired} Syntax Description receive Specifies th at the in terface pro cesses p au se frames.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches flowcontrol Tab le 2-4 des cribes the guidelines for using the d ifferent config urations of the send and receive keywo rds with th e flo wcontrol command. Table 2-4 Keyword Configurations for send and receive Configuratio n Description send on En ables a local po rt to sen d pau se frames to remote ports. To o btain pred ictable results, us e send on o nly when remote ports are set to receive on o r receive desired.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches flowcontrol This examp le shows how to set receive flow contro l to desired: Switch(config-if)# flowcontrol receive desired Switch(config-if)# Related Commands Co mmand interface port-channel Description Accesses or creates a po rt-ch ann el interface. interface range show flowco ntro l Runs a command on multiple p orts at th e same time. Displays the per-interface status and statistics related to flow control.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches hardware statistics hardware statistics To en able TCAM hard ware s tatistics in y our ACLs us e the hardware statistics command. To disable TCAM hardware statistics , use the no form of this comman d. hardware statistics no hardware statistics Syntax Description This command has no arguments or keywo rds. Defaults Hardware statistics is disabled.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches hw-module beacon hw-module beacon To control the beacon LED in conjunction with the beacon button, enter the hw-module beacon co mmand : hw-module bea con [o n | off] Syntax Description on off Defaults none Command Modes Usage Guidelines Tu rns on the LED. Turns off the LED.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches hw-module power hw-module power To turn the power off on a slot or line module, use th e no hw-module power comman d. To turn the power b ack on, use the hw-module power command. hw-module [slot | module] numb er power no hw-module [slot | module] nu mber power Syntax Description Defaults slo t (Optio nal) Sp ecifies a slot on a chassis. module n umber (Optio nal) Sp ecifies a line mo dule. Slot or mo dule nu mber.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches hw-module system max-queue-limit hw-module system max-queue-limit To enable a u ser to change the qu eue limit for all interfaces glob ally use the hw-mo dule s ystem max-queue-limit comman d. To cancel the global setting, use th e no form of the command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches instance instance To map a VLAN or a set of VLANs to an MST instance, use th e instance command. To return the VLANs to the common instance default, u se the no form of this command. instance instance-id {vlans vla n-ra nge} no instance ins tance-id Syntax Description in stance-id v lans vlan-range Defaults Mappin g is dis abled.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches instance Co mmand Description show spanning-tree mst spanning-tree mst config uration Displays MST protocol in formatio n. Enters the MST con figuratio n s ubmode. Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches instance Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
22 Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches interface interface To select an in terface to con figure and to en ter in terface co nfigu ration mode, use the interfa ce co mmand . interface type nu mber Syntax Description typ e number Defaults No interface ty pes are co nfigured. Command Modes Glob al co nfigu ration mode Usage Guidelines Typ e of in terface to be configured; see Table 2-6 for valid values. Module an d p ort numb er.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches interface Examples This example s hows how to enter the interface con figuratio n mo de on the Fast Ethern et interface 2 /4: Switch(config)# interface fastethernet2/4 Switch(config-if)# Related Commands Command show interfa ces Descriptio n Displays interface information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches interface port-channel interface port-channel To access or create a port-channel interface, use th e interface port-channel command. interface port-channel channel-group Syntax Description cha nnel-group Defaults This comman d has no default settings. Command Modes Usage Guidelines Port-ch ann el group numb er; valid valu es are from 1 to 64 .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches interface range interface range To run a co mmand on multip le ports at the s ame time, u se the interface ra ng e comman d. interfa ce range {vlan vlan _id - vla n_id} {port-range | macro na me} Syntax Description v lan vlan_id - vlan_ id Specifies a VLAN range; valid values are fro m 1 to 409 4. p ort-ran ge Port rang e; fo r a list of valid valu es fo r port-range, see th e “Usage Guid elines” s ection.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches interface range • Vlan vla n_id You can not specify both a macro an d an interface range in the same command. After creating a macro, you can enter ad ditional ranges. If you have alread y entered an interface range, th e CLI do es not allow you to enter a macro. You can sp ecify a single in terface in the po rt-rang e valu e. This makes the command similar to the interface interface-number command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches interface vlan interface vlan To create or access a Lay er 3 switch virtual in terface (SVI), use the interface vla n co mmand . To delete an SVI, use the no form of this comman d. interfa ce vlan vlan_ id no interface vla n vlan_id Syntax Description vlan_ id Defaults Fast EtherChannel is no t sp ecified.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip admission proxy http refresh-all ip admission proxy http refresh-all To ensure that you see a customized WebAuth login page with the same name in the switch system directory as a same-named prior lo gin page, use th e ip a dmission proxy http refresh-a ll command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip arp inspection filter vlan ip arp inspection filter vlan To permit ARPs from hosts that are configu red for static IP when DAI is enabled and to define an ARP access list and apply it to a VLAN, use the ip arp ins pection filter v lan command. To disable this application, u se the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip arp inspection filter vlan 1 Switch# Related Commands Acl-Match Deny Co mmand Description arp access-list Defines an ARP access list or add s clauses at the end of a predefined list. Displays the status of dynamic ARP inspection for a specific range of VLANs. show ip arp inspection Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip arp inspection limit (interface) ip arp inspection limit (interface) To limit th e rate o f incoming ARP requests and res ponses on an interface an d p revent DAI from consu ming all of th e system’s resources in the even t of a Do S attack, use the ip arp inspection limit command. To release the limit, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip a rp inspection limit (interface) Examples This examp le shows how to limit the rate of th e incoming ARP requests to 25 packets per secon d: Switch# config terminal Switch(config)# interface fa6/3 Switch(config-if)# ip arp inspection limit rate 25 Switch(config-if)# end Switch# show ip arp inspection interfaces fastEthernet 6/3 Interface Trust State Rate (pps) --------------- -------------------Fa6/3 Trusted 25 Switch# This example s
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip arp inspection log-buffer ip arp inspection log-buffer To co nfigure th e parameters th at are associated with th e logg in g buffer, use th e ip a rp inspection log-buffer command. To disable the parameters, u se the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip arp insp ection log-buffer Related Commands Co mmand arp access-list show ip arp inspection Description Defines an ARP access list or add s clauses at the end of a predefined list. Displays the status of dynamic ARP inspection for a specific range of VLANs. Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip arp inspection trust ip arp inspection trust To set a p er-po rt co nfigu rable trust state that determines the set of interfaces where inco ming ARP p ackets are inspected, use the ip arp inspectio n trust command. To make the interfaces u ntru sted, use th e no form o f this co mmand . ip arp inspectio n trust no ip arp inspection trust Syntax Description This command has no arguments or keywo rds.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip arp inspection validate ip arp inspection validate To perfo rm specific ch ecks for ARP inspectio n, use th e ip arp ins pection validate command. To disable ch ecks, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip arp inspection validate Vlan ---1 Vlan ---1 Switch# Related Commands Configuration ------------Enabled Operation --------Active ACL Logging ----------Deny DHCP Logging -----------Deny ACL Match --------- Static ACL ---------- Command a rp access-list Descriptio n Defines an ARP access list or adds claus es at the en d of a p redefined list.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip arp inspection vlan ip arp inspection vlan To enable dy namic ARP in spection (DAI) on a p er-VLAN basis, use the ip arp inspection v lan co mmand . To d isable DAI, use the no fo rm of this command. ip arp inspection v lan vlan-range no ip arp inspectio n vlan vla n-ra nge Syntax Description vla n-ran ge Defaults ARP in spection is disabled on all VLANs.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip arp inspection vlan Related Commands Command a rp access-list show ip arp inspectio n Descriptio n Defines an ARP access list or adds claus es at the en d of a p redefined list. Displays the status of dy namic ARP in spection for a sp ecific range o f VLANs. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip arp inspec tion vlan logging ip arp inspection vlan logging To control the type of packets that are log ged , use the ip arp ins pection vlan logging co mmand . To disable this logg ing co ntrol, use th e no form of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip arp inspection vlan logging Switch(config)# ip arp inspection vlan 1 logging acl-match matchlog Switch(config)# end Switch# show ip arp inspection vlan 1 Source Mac Validation : Enabled Destination Mac Validation : Disabled IP Address Validation : Disabled Vlan ---1 Vlan ---1 Switch# Related Commands Configuration ------------Enabled Operation --------Active ACL Logging ----------Acl-Match DHCP Logging -----------Deny Command a
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip cef load-sharing algorithm ip cef load-sharing algorithm To co nfigure the load-s haring h ash fu nctio n so th at the source TCP/UDP port, the destinatio n TCP/UDP port, or both ports can be inclu ded in th e hash in additio n to the source and destin ation IP addresses , use the ip cef load-sharing algo rithm command. To revert back to the defau lt, wh ich does not include the ports, use the no fo rm of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip cef load-sharing algorithm This ex ample shows how to co nfigu re the IP CEF load-sharing algo rithm that includes Layer 4 tunneling p orts: Switch(config)# ip cef load-sharing algorithm include-ports tunnel Switch(config)# Related Commands Command show ip cef v lan Descriptio n Displays the IP CEF VLAN interface status and configuration information . Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip device tracking maximum ip device tracking maximum To enable IP po rt security binding tracking o n a Layer 2 port, use the ip device tracking maximum co mmand . To disable IP port security o n un trusted Layer 2 interfaces, use the no form of th is comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip dhcp snooping ip dhcp snooping To en able DHCP snoo ping globally, use the ip dhcp snooping co mmand . To d isable DHCP snoo ping, u se the no form of th is command. ip dhcp snooping no ip dhcp snooping Syntax Description This command has no arguments or keywo rds. Defaults DHCP snoopin g is disabled.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip dhcp snoop ing binding ip dhcp snooping binding To set u p and generate a DHCP bind ing configuration to restore binding s across reb oots, use the ip dhcp snooping binding command. To disable the bindin g configuration , use the no fo rm of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip dhcp snooping database ip dhcp snooping database To store the b indings that are generated b y DHCP snoopin g, use the ip dhcp snooping database command. To either reset the timeou t, reset the write-delay, or delete the agent specified by the URL, u se the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip dh cp snooping database Examples This examp le shows how to sto re a datab ase file with th e IP address 10.1.1.1 within a directory called directory. A file named file must be present on the TFTP server. Switch# config terminal Switch(config)# ip dhcp snooping database tftp://10.1.1.1/directory/file Switch(config)# end Switch# show ip dhcp snooping database Agent URL : tftp://10.1.1.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip dhcp snooping information option ip dhcp snooping information option To enable DHCP op tion 8 2 data insertion, use the ip dhcp snoo ping information o ption command. To d isable DHCP option 8 2 d ata insertion, use th e no form o f this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip dhcp snooping information option Switch(config-if)# ip dhcp snooping vlan 555 information option format-type circuit-id string customer-500 Switch(config)# end Related Commands Co mmand ip dhcp snooping Description Glob ally enables DHCP sn ooping . ip dhcp snooping binding Sets up and generates a DHCP b inding config uration to restore bind ings across reboots. Enables DHCP option 82 data in sertion.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip dhcp snooping information option allow-untrusted ip dhcp snooping information option allow-untrusted To allow DHCP packets with option 82 data inserted to be received from a snoop ing u ntru sted port, use th e ip dhcp snooping information option allow-untrusted co mmand . To d isallow receipt of these DHCP packets, use the no fo rm of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip dhcp snoop ing limit rate ip dhcp snooping limit rate To con figure th e n umber of the DHCP messages that an interface can receive per second, use the ip dhcp snooping limit rate co mmand . To d isable the DHCP s noopin g rate limiting, use the no form of this co mmand . ip dhcp snooping limit rate rate no ip dhcp s noo ping limit ra te Syntax Description rate Number of DHCP messages a switch can receive per second .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip dhcp snooping trust ip dhcp snooping trust To co nfigure an interface as trusted fo r DHCP sno oping purposes, use the ip dhcp snooping trust command. To config ure an interface as untrusted, us e the no form of th is command. ip dhcp snooping trust no ip dhcp snooping trust Syntax Description This command has no arguments or keywo rds. Defaults DHCP snoopin g trust is disabled .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip dhcp snooping vlan ip dhcp snooping vlan Use the ip dhcp snooping vlan command to enab le DHCP sno oping on a VLAN. To disable DHCP snoop ing on a VLAN, use the no fo rm of this command. ip dhcp snooping [vlan number ] no ip dhcp s nooping [vlan n umber] Syntax Description Defaults Command Modes Usage Guidelines Examples vlan numb er (Optional) Single VLAN number or a rang e of VLANs; valid values are from 1 to 4094.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip dhcp snooping vlan Related Commands Command ip dhcp snooping Descriptio n Globally enables DHCP snoo ping. ip dhcp snoo ping informa tion option ip dhcp snoo ping limit ra te Enab les DHCP op tion 82 data insertio n. Con figures the number of the DHCP messages th at an in terface can receive p er s econd.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip dhcp snoo ping vlan information option format-type circuit-id string ip dhcp snooping vlan information option format-type circuit-id string To enable circuit-id (a sub option of DHCP sn ooping op tion 82) on a VLAN, u se the ip dhcp snooping vlan information optio n format-type circuit-id string co mmand . To disable circuit-id o n a VLAN, use the no fo rm of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip dhcp snooping vlan information option format-type circuit-id string Switch(config-if)# ip dhcp snooping vlan 250 information option format-type circuit-id override string testcustomer You can verify your settings by entering the show ip dhcp snoo ping user EXEC command. Note Related Commands The show ip dhcp snooping u ser EXEC command only displays the global command output, in clud ing a remote-ID co nfigu ration.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip igmp filter ip igmp filter To co ntrol whether all h osts on a Layer 2 interface can join one or more IP multicast gro ups by applying an IGMP p rofile to th e interface, use the ip igmp filter co mmand. To remove a p rofile fro m the in terface, use th e no form o f this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip igmp max-groups ip igmp max-groups To set the maximu m nu mber of IGMP gro ups that a Layer 2 in terface can join, use th e ip igmp max-gro ups comman d. To set the maximum back to th e default, u se the no form of th is command. ip igmp ma x-g roups numb er no ip ig mp max -groups Syntax Description n umber M aximu m number of IGMP gro ups that an interface can join; valid valu es are from 0 to 4 29496 7294.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip igmp profile ip igmp profile To create an IGMP profile, use the ip igmp profile command . To d elete the IGMP profile, u se the no form of this comman d. ip igmp profile p rofile n umber no ip igmp profile profile number Syntax Description profile number Defaults No profile created. Command Modes IGMP pro file nu mber bein g con figured ; valid values are fro m 1 to 42 949672 95.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip igmp query-interval ip igmp query-interval To co nfigure th e frequency that the switch sends the IGMP hos t-query messages, us e the ip igmp query-interval command. To return to the default freq uency, use the no fo rm of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip igmp query-interval Co mmand Description ip pim query-interval (refer to Cisco Config ures the frequency o f Proto col Indepen den t IOS do cumentation) Multicast (PIM) router query messages.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip igmp snooping ip igmp snooping To enable IGMP sn ooping , use the ip ig mp snoo ping co mmand. To disable IGMP sno oping, u se the no form of this command. ip igmp snooping [tcn {floo d query count coun t | query solicit}] no ip ig mp sno oping [tcn {flood query count count | query solicit}] Syntax Description Defaults tcn flood (Optio nal) Sp ecifies the top ology chan ge config urations.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip igmp snooping Switch(config)# no ip igmp snooping tcn flood Switch(config)# This examp le shows how to enable an IGMP g eneral query : Switch(config)# ip igmp snooping tcn query solicit Switch(config)# This examp le shows how to d isable an IGMP general q uery: Switch(config)# no ip igmp snooping tcn query solicit Switch(config)# Related Commands Co mmand Description ip igmp snooping v lan immedia te-leave Enable IGMP immed iate-lea
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip igmp snooping report-suppression ip igmp snooping report-suppression To en able report suppress io n, us e the ip igmp snooping repo rt-suppression command. To dis able report sup pression and fo rward the repo rts to the multicast d evices , use the no form of this comman d. ip igmp snooping report-suppression no igmp snooping report-suppression Syntax Description This command has no arguments or keywo rds.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip igmp snooping report-suppression Related Commands Co mmand Description ip igmp snooping v lan immedia te-leave Enable IGMP immed iate-leav e processing . ip igmp snoo ping vlan mrouter Config ures a Layer 2 interface as a multicast router interface for a VLAN. ip igmp snoo ping vlan sta tic Config ures a Layer 2 interface as a member of a g rou p. Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip igmp snooping vlan ip igmp snooping vlan To en able IGMP sn ooping for a VLAN, u se the ip igmp snooping vlan command. To disable IGMP sn ooping , use the no fo rm of this comman d. ip igmp snooping vlan vlan-id no ip ig mp sno oping vla n vlan-id Syntax Description vlan-id Defaults IGMP snoo ping is disab led.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip igmp snooping vlan explicit-tracking ip igmp snooping vlan explicit-tracking To enable per-VLAN explicit host tracking, use the ip igmp snooping vlan explicit-tracking command. To disable explicit host tracking, use the no form of this command. ip igmp snoo ping vlan vla n-id explicit-tracking no ip igmp snooping vlan vlan-id ex plicit-tracking Syntax Description vla n_id Defaults Explicit host tracking is en abled.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip igmp snooping vlan immediate-leave ip igmp snooping vlan immediate-leave To en able IGMP immediate-leave process ing, u se the ip igmp snooping vlan immediate-leave command. To disable immediate-leave p rocessing, u se the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip igmp snooping vlan mrouter ip igmp snooping vlan mrouter To statically configu re an Layer 2 interface as a multicas t router interface for a VLAN, use the ip igmp snoo ping vlan mrouter command. To remove th e configu ration, use the no form of this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip igmp snooping vlan mrouter This example s hows how to specify the mu lticast switch learn ing metho d: Switch(config-if)# ip igmp snooping 400 mrouter learn cgmp Switch(config-if)# Related Commands Command ip igmp snooping Description En able IGMP sn ooping. ip igmp snooping vlan immediate-leave En able IGMP immediate-leave process ing. ip igmp snooping vlan static Configures a Layer 2 interface as a member of a group.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip igmp snooping vlan static ip igmp snooping vlan static To config ure a Layer 2 interface as a member of a grou p, us e the ip igmp snooping vlan static co mmand . To remove the configuratio n, use the no fo rm of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip local-proxy-arp ip local-proxy-arp To enable the local pro xy ARP feature, use the ip local-pro xy-arp command. To disable the local proxy ARP feature, use the no form o f this co mmand . ip local-proxy-arp no ip lo cal-prox y-arp Syntax Description This command has no arguments or keywo rds. Defaults Local proxy ARP is d is abled.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip mfib fastdrop ip mfib fastdrop To enable MFIB fast drop, u se the ip mfib fastdrop command. To disable M FIB fas t drop, use th e no form of this comman d. ip mfib fastdrop no ip mfib fastdrop Syntax Description This comman d has no argu ments or keyword s. Defaults MFIB fast drop is enabled.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip multicast multipath ip multicast multipath To en able load s plitting of IP multicast traffic over Equal Cost Multip ath (ECMP), use the ip multicast multipath co mmand in global configuration mode. To dis able this functionality, us e th e no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip multicast multipath If the ip multicast multipath comman d is configured with th e s-g-hash key word and multip le eq ual-cost path s exist, lo ad splittin g will o ccur across equal-cost paths based on so urce and group ad dress or on so urce, g rou p, and next-hop add ress.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip source binding ip source binding To ad d o r delete a static IP source bind ing entry, use th e ip s ource binding co mmand . To d elete the correspon ding IP source bindin g entry, use th e no form o f this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip sticky-arp ip sticky-arp To enable sticky ARP, use the ip sticky -arp command. Use th e no form of this comman d to d is able sticky ARP. ip sticky-arp no ip sticky-a rp Syntax Description This comman d has no argu ments or keyword s. Defaults Enabled Command Modes Glob al co nfigu ration mode Usage Guidelines This comman d is su pported on PVLANs o nly.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip sticky-arp Related Commands Command a rp (refer to Cisco IOS d ocu mentation) Descriptio n Enab les Address Res olution Proto col (ARP) entries for static rou ting over th e Switched Multimegabit Data Serv ice (SMDS) network. show a rp (refer to Cisco IOS d ocu mentation) Displays ARP in formatio n. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip verify head er vlan all ip verify header vlan all To enable IP header validation for Layer 2-switched IPv4 pack ets, use the ip verify hea der vla n all co mmand . To d isable the IP header valid ation , use the no form of this comman d. ip verify hea der vla n all no ip verify header vlan all Syntax Description This comman d has no default settings. Defaults The IP header is valid ated for brid ged and routed IPv4 packets.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip verify source ip verify source To enable IP source gu ard on u ntru sted Lay er 2 interfaces, use the ip verify so urce command. To disab le IP so urce g uard on untrusted Layer 2 in terfaces, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip verify source You can verify you r settin gs by entering the show ip verify so urce privileged EXEC command. Related Commands Co mmand ip dev ice tracking ma ximum ip dhcp snooping Description Enables IP port secu rity binding tracking on a Layer 2 p ort. Glob ally enables DHCP sn ooping . ip dhcp snooping info rmatio n option Enables DHCP option 82 data in sertion.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip verify unicast source reachable-via ip verify unicast source reachable-via To en able an d configure unicast RPF checks on a IPv 4 in terface, use the ip verify unicast s ource reachable-via command. To disable un icast RPF, use the no form o f this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip wccp ip wccp To enable sup port of the specified Web Cache Co mmunication Protocol (WCCP) service for participatio n in a service group, u se the ip wccp comman d in global con figuratio n mod e. To d isable th e service group, use th e no form of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip wccp Usage Guidelines This command instru cts a rou ter to en able o r disab le the supp ort for th e specified service number or the web -cache service name. A service n umber can be from 0 to 25 4. Once the service number or name is enabled, the rou ter can participate in the estab lishment o f a serv ice grou p.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip wccp up to a maximum of eight characters. Messages that d o n ot authenticate when authenticatio n is en abled on the router are discarded. Th e default is for n o auth entication pas sword to b e config ured an d for au then tication to be dis abled. Examples The following example sh ows how to co nfigu re a rou ter to run WCCP rev erse-proxy service, using the multicast address of 2 39.0.0.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip wccp check services all ip wccp check services all To enable all Web Cach e Commu nication Protocol (WCCP) services, use the ip wccp check serv ices all command in global con figuratio n mode. To d isable all serv ices, us e the no form of th is command. ip wccp check serv ices all no ip wccp check services all Syntax Description This command has no arguments or keywo rds. Defaults WCCP serv ices are no t enabled o n th e router.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip wccp check services all Related Commands Co mmand ip wccp ip wccp group -listen ip wccp red irect Description Enables suppo rt of the sp ecified WCCP service for participation in a service gro up. Config ures an interface o n a rou ter to enable or d isab le the reception of IP multicast packets fo r Web Cach e Communicatio n Protocol (WCCP).
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip wccp group-listen ip wccp group-listen To co nfigure an interface on a router to enab le or dis able the reception of IP multicas t packets for Web Cach e Communication Protocol (WCCP), u se the ip wccp group-listen co mmand in interface configuration mode. To disab le the reception of IP multicast packets for WCCP, u se the no form o f this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip wcc p group-listen Co mmand Description ip wccp red irect exclu de in Configures an interface to ex clud e packets received on an interface from b eing check ed for redirection . Specifies which vers io n of WCCP you wish to u se on you r router. ip wccp version Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ip wccp redirect ip wccp redirect To en able packet redirection on an in bound or outbou nd interface usin g Web Cache Co mmunication Protocol (WCCP), use the ip wccp redirect command in interface configuration mod e. To disable WCCP red irection , use the no fo rm of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip wccp redirect The following example shows how to config ure a session in which HTTP traffic arriving on GigabitEth ernet interface 3/1 is redirected to a Cach e Eng ine: Switch(config)# ip wccp web-cache Switch(config)# interface gigabitethernet 3/1 Switch(config-if)# ip wccp web-cache redirect in Related Commands Co mmand ip wccp check serv ices all Description Configures an interface on a router to enab le or d isab le the receptio
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches p wccp redirect exclude in p wccp redirect exclude in To config ure an interface to exclu de p ackets received on an interface from b eing checked for redirection , u se the ip wccp redirect exclude in command in interface configu ration mode. To disable the ability of a rou ter to exclude p ackets fro m red irectio n checks, us e the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ipv6 mld snooping ipv6 mld snooping To enable IP version 6 (IPv6 ) Multicast Listener Discov ery (MLD) snoo ping glo bally or on the specified VLAN, u se the ipv6 mld snooping command withou t keywords. To dis able MLD snoopin g on a switch or the VLAN, use the no form o f this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ipv6 mld snooping Related Commands Command show ipv6 mld snooping Descriptio n Displays IP version 6 (IPv6) Mu lticast Listener Discovery (MLD) snoop ing con figuratio n o f the switch or the VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ipv6 mld snooping last-listener-query-count ipv6 mld snooping last-listener-query-count To config ure IP version 6 (IPv6) M ulticast Listener Discovery Mulitcast Address Specific Qu eries (MASQs) that will be sent before aging ou t a client, u se the ipv 6 mld snoo ping last-listener-query-count command. To reset the qu ery count to the default setting s, use the no form of this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ipv6 mld snooping last-listener-query-count You can verify your settings by entering the show ipv 6 mld sno oping [vlan vlan -id] u ser EXEC command. Related Commands Command ipv6 mld snooping la st-listener-query-interval Descriptio n Con figures IP vers ion 6 (IPv 6) Multicas t Lis tener Disco very (MLD) sno oping last-listener query in terval on th e switch or on a VLAN.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ip v6 mld snooping last-listener-query-interval ipv6 mld snooping last-listener-query-interval To config ure IP version 6 (IPv6) M ulticast Listener Discovery (MLD) snoopin g last-listen er q uery interval o n th e switch or o n a VLAN, use th e ipv6 mld sno oping las t-listener-query-interval co mmand . To reset the q uery time to the defau lt settings, use th e no form of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ipv6 mld snooping last-listener-query-interval Switch(config)# end Switch# You can verify your settings by entering the show ipv 6 MLD snooping [v lan vlan-id] user EXEC command. Related Commands Command ipv6 mld snooping last-listener-query-count Descriptio n Con figures IP vers ion 6 (IPv 6) Multicas t Lis tener Disco very Mulitcast Add ress Sp ecific Queries (MASQs) th at will be s ent befo re aging o ut a client.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ipv6 mld snoop ing listener-message-suppression ipv6 mld snooping listener-message-suppression To enable IP versio n 6 (IPv6 ) Multicast Listener Discovery (MLD) snoo ping listener message suppression, use the ipv6 mld s nooping listener-message-suppression command. To dis able MLD snoop ing listen er message su ppressio n, use the no fo rm of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ipv6 mld snooping robustness-variable ipv6 mld snooping robustness-variable To co nfigure th e number of IP version 6 (IPv6) Mu lticast Listener Discovery (MLD) queries th at the switch sends before deleting a lis tener that does not respond , or to enter a VLAN ID to config ure the n umber of queries per VLAN, use th e ipv6 mld sno oping robustness-variable comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ipv6 mld sn ooping ro bustne ss-variable Switch(config)# end Switch# You can verify you r settin gs by entering the show ipv6 MLD sno oping [vlan vlan -id] user EXEC co mmand . Related Commands Co mmand ipv 6 mld sno oping last-listener-query-count Description Config ures IP version 6 (IPv6) Mu lticast Listener Discovery Mulitcast Address Specific Qu eries (MASQs) that will be sent b efore ag ing out a clien t.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ipv6 mld snooping tcn ipv6 mld snooping tcn To co nfigure IP version 6 (IPv 6) Multicast Listener Disco very (MLD) Topolog y Ch ang e No tifications (TCNs ), us e the ipv6 mld snooping tcn co mmand s. To reset the defau lt settings, us e the no form of the commands.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches ipv6 mld snooping vlan ipv6 mld snooping vlan To config ure IP version 6 (IPv6) M ulticast Listener Discovery (MLD) snoopin g parameters on the VLAN interface, use the ipv6 mld snooping vlan command. To reset the parameters to the default settin gs, us e the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches ipv6 mld snooping vlan This example s hows how to disable MLD Immediate-Leave pro cessing on VLAN 1: Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# no ipv6 mld snooping vlan 1 immediate-leave Switch(config)# end Switch# This example s hows how to config ure a port as a multicast s witch p ort: Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches issu abortversion issu abortversion To cancel the ISSU up grade or the down grade process in progress an d to res to re the Catalyst 4500 series switch to its state b efore the start of the process , use the issue a bortversion co mmand . issu a bo rtversion active-slo t [active-image-new] Syntax Description active-slo t active-image-new Specifies the slot nu mber for the current s tand by s uperviso r en gine.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches issu acceptversion issu acceptversion To halt the rollb ack timer and to ensure that the new Cisco IOS software image is no t automatically sto pped durin g the ISSU process , use the issu acceptvers ion command. iss u acceptversion a ctive-slot [active-ima ge-new] Syntax Description a ctive-slot Specifies the slot number for the currently active superviso r engine.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches issu acceptversion Co mmand Description issu runvers ion Fo rces a change from the active s uperviso r en gine to the stan dby superv isor engine an d causes th e newly active superv isor engine to run the new image s pecified. Configures the In Service Software Upgrade (ISSU) rollb ack timer value. Displays the ISSU state an d current booted image name during the ISSU p rocess.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches issu commitversion issu commitversion To load th e new Cisco IOS software image into the new stand by superviso r engine, use the issu commitversion co mmand . iss u commitversion s tandby-s lot [stand by-imag e-new ] Syntax Description sta ndby-slo t Specifies the slot number for the currently active superviso r engine. sta ndby-image-new (Optio nal) Name of the new image on the cu rrently active superv isor eng ine.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches issu commitversion Co mmand Description issu runvers ion Fo rces a change from the active s uperviso r en gine to the stan dby superv isor engine an d causes th e newly active superv isor engine to run the new image s pecified. Displays the ISSU state an d current booted image name during the ISSU p rocess. show issu s tate Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches issu loadversion issu loadversion To start the ISSU p rocess, use the issu loadversio n comman d. iss u loadvers ion active-slot active-image-new sta ndby-slo t sta ndby-image-new [force] Syntax Description a ctive-slot a ctive-imag e-new sta ndby-slo t Defaults Specifies the slot nu mber for the currently active supervisor engin e. Specifies th e name o f th e new image on the cu rrently active supervisor engine.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches issu loadversion Co mmand Description issu runvers ion Fo rces a change from the active s uperviso r en gine to the stan dby superv isor engine an d causes th e newly active superv isor engine to run the new image s pecified. Displays the ISSU state an d current booted image name during the ISSU p rocess. show issu s tate Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches issu runversion issu runversion To force a change from th e active su pervisor eng ine to the stand by supervis or engine and to cau se the n ewly active s uperviso r engine to run th e n ew image specified in the issu loadversion co mmand , u se th e iss u runversion co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches issu set rollba ck-timer issu set rollback-timer To config ure the In Service Software Up grade (ISSU) rollb ack timer value, u se the issu set rollback-timer co mmand . issu set rollback-timer secon ds Syntax Description secon ds Specfies th e rollb ack timer value, in seconds. The valid timer valu e range is from 0 to 720 0 seco nds (2 h ours ). A value o f 0 secon ds disables the rollback timer.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches l2protocol-tunnel l2protocol-tunnel To en able pro toco l tu nneling on an interface, us e the l2 protoco l-tunnel command. You can enab le tu nneling for the Cisco Discovery Protocol (CDP), Spannin g Tree Proto col (STP), o r VLAN Trunking Protocol (VTP) packets. To disable tun nelin g o n the interface, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches l2protocol-tu nnel cos l2protocol-tunnel cos To config ure the class o f service (CoS) valu e fo r all tun neled Layer 2 pro toco l p ackets, use the l2protocol-tunnel co s co mmand . To return to the default value of zero, use the no fo rm of this comman d. l2protocol-tunnel cos value no l2protocol-tunnel cos Syntax Description va lue Specifies the CoS priority value fo r tu nneled Layer 2 protocol p ackets.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches l2protocol-tunnel drop-threshold l2protocol-tunnel drop-threshold To set a d rop threshold for the maximum rate of Layer 2 protocol packets p er second to be received b efore an interface drops packets, use the I2protocol-tunnel dro p-threshold command. You can s et th e d rop threshold fo r the Cisco Discovery Pro toco l (CDP), Sp an ning Tree Protocol (STP), or VLAN Trunkin g Pro toco l (VTP) packets.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches l2protocol-tunnel shutdown-threshold l2protocol-tunnel shutdown-threshold To con figure the protocol tunneling en capsulation rate, use the I2protocol-tunnel shutdown-threshold co mmand . You can set the encapsulation rate for the Cisco Discovery Protocol (CDP), Spanning Tree Protocol (STP), or VLAN Tru nking Proto co l (VTP) p ackets. To d isab le the encapsulation rate on the interface, use th e no form of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches l2protocol-tunnel shutdown-threshold Command Descriptio n l2 proto col-tunnel cos Con figures the class of service (CoS) value for all tunneled Layer 2 protocol packets. Sets a drop threshold for the max imum rate of Lay er 2 p rotocol pack ets per seco nd to be received before an in terface dro ps packets. l2protocol-tunnel drop-threshold Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches lacp port-priority lacp port-priority To set the LACP prio rity for the p hysical interfaces, use the lacp po rt-priority co mmand . lacp port-priority pr iority Syntax Description priority Defaults Priority is set to 32768 . Priority for the phy sical interfaces; valid values are from 1 to 6553 5.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches lacp system-priority lacp system-priority To set the prio rity of th e system for LACP, use th e lacp sys tem-priority command. la cp system-priority priority Syntax Description p riority Defaults Priority is set to 32 768. Priority of the system; valid values are from 1 to 65535 .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches lldp tlv-select po wer-management lldp tlv-select power-management To to enab le power n ego tiation through LLDP, u se the lldp tlv-select power-ma na gement in terface co mmand . lldp tlv -select power-management Syntax Description This comman d has no argu ments or keyword s. Defaults Enabled on POEP ports Command Modes Interface level Command History Re lea se 12.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches logging event link-status global (global configuration) logging event link-status global (global configuration) To ch ang e the d efau lt switch -wid e glob al link-statu s even t messaging settings, use the lo gging event link-status global command. Use the no form of this comman d to disable the link-status even t messaging.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches logging event link-status (interface configura tion) logging event link-status (interface configuration) To enab le the link -status event messaging on an interface, use the logging ev ent link-status co mmand . Use the no form of this comman d to d isab le link-statu s even t messaging. Use the logging ev ent link-status use-global comman d to apply th e global link-statu s setting.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches logging event link-status (interface configuration) Related Commands Command Descriptio n lo gging event link-status global (global Changes the d efault switch-wid e global link-statu s even t configuration) messaging settings. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches logg ing event trunk -status global (global configura tion) logging event trunk-status global (global configuration) To enable the trun k-status event mes sag in g globally, use the logging event trunk-status global co mmand . Use the no fo rm of this command to disable trunk-statu s even t messaging. logging ev ent trunk-status global no lo gging event trunk-status global Syntax Description This comman d has no argu ments or keyword s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches logging event trunk-status (interface configuration) logging event trunk-status (interface configuration) To en able the trunk-status event messaging on an interface, use th e logg ing event trunk-status command. Use th e no form o f this co mmand to dis able the trunk-statu s event messaging. Use the lo gging event trunk-status use-global command to apply the g lobal trunk-status setting .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches logging event trunk-status (interface configura tion) Related Commands Co mmand logging ev ent trunk-status global (glo ba l configuratio n) Description Enables th e trunk-statu s even t messaging on an interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches mab mab To enable and con figure MAC au thorization byp ass (MAB) on a po rt, use the mab command in interface configuration mod e. To disable MAB, us e the no form of th is command. mab [eap] no mab [ea p] Note The mab command is totally ind epend ent of th e effect o f the dot1x system-a uth control command .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches mac access-list extended mac access-list extended To define the extended MAC access lists, use the mac acces s-list extended comman d. To remove the MAC access lists, u se the no form of th is command. mac access-list extended n ame no mac access-list extended na me Syntax Description name Defaults MAC access lists are no t defin ed.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches mac access-list extended Table 2-7 mac access-list extended Subcommands (continued) Subcommand Description n ame-coded ethertype (Optional) Denotes a predefined name-coded ethertyp e for common protocols : aarp—Ap pleTalk ARP amb er—DEC-Amb er ap pletalk—AppleTalk/Eth erTalk dec-spanning— DEC-Span ning-Tree decnet-iv— DECnet Phase IV diagnostic—DEC-Diagn ostic dsm—DEC-DSM ety pe-600 0—0x6 000 ety pe-804 2—0x8 042 lat— DEC-LAT lavc-s
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches mac access-list extended Table 2-8 Mapping an Ethernet Packet to a Protocol Family Protocol Family Ethertype in Pack et Header Ipv 6 0x86 DD Rarp-Ipv4 0x80 35 and p rotocol head er of Rarp is Ipv 4 Rarp-Non-Ip v4 0x80 35 and p rotocol head er of Rarp is a non -Ipv4 protocol family Vines 0x0BAD, 0x0 BAE, 0 x0BAF Xns 0x06 00, 0 x0807 Wh en yo u enter the src-mac mask or dest-mac mask value, follow these gu idelin es: • • Enter
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches mac-address-table aging-time mac-address-table aging-time To con figure the agin g time for th e en tries in the Layer 2 table, use the mac-address-table aging-time command. To reset the seco nds valu e to the default setting, u se the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches mac-address-table dynamic grou p protoco ls mac-address-table dynamic group protocols To en able th e learn in g of MAC add resses in b oth th e “ip” and “o th er” protocol buckets, even tho ugh the incoming packet may belong to on ly o ne of the protocol buckets, use th e mac-addres s-table dy na mic group protocols command. To disable grouped learnin g, use th e no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches mac-address-table dynamic group protocols 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Switch# 0004.5a5f.06f7 0004.5a5f.072f 0004.5a5f.08f6 0004.5a5f.090b 0004.5a88.b075 0004.c1bd.1b40 0004.c1d8.b3c0 0004.c1d8.bd00 0007.e997.74dd 0007.e997.7e8f 0007.e9ad.5e24 000b.5f0a.f1d8 000b.fdf3.c498 0010.7be8.3794 0012.436f.c07f 0050.0407.5fe1 0050.6901.65af 0050.da6c.81cb 0050.dad0.af07 00a0.ccd7.20ac 00b0.64fd.1c23 00b0.64fd.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches mac-address-table dynamic grou p protoco ls 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Switch# 0004.c1bd.1b40 0004.c1d8.b3c0 0004.c1d8.bd00 0005.dce0.7c0a 0007.e997.74dd 0007.e997.7e8f 0007.e9ad.5e24 0007.e9c9.0bc9 000b.5f0a.f1d8 000b.fdf3.c498 0012.436f.c07f 0050.0407.5fe1 0050.6901.65af 0050.da6c.81cb 0050.dad0.af07 00a0.ccd7.20ac 00b0.64fd.1b84 00d0.b775.c8bc 00d0.b775.c8ee 00d0.b79e.de1d 00e0.4c79.1939 00e0.4c7b.d765 00e0.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches mac address-table learning vlan mac address-table learning vlan To enable MAC addres s learning on a VLAN, use the mac address-table learning glo bal co nfigu ration command. Use th e no form o f this co mmand to dis able MAC address learnin g o n a VLAN to control which VLANs can learn MAC addresses.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches mac address-table le arning vlan Examples This examp le shows how to d isable MAC add ress learn ing on VLAN 200 3: Switch(config)# no mac address-table learning vlan 2003 Related Commands Co mmand show mac address-table learning Descriptio n Displays the MAC ad dress learning statu s o n all VLANs or o n th e specified VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches mac-address-table notification mac-address-table notification To enable MAC address notification on a s witch, use the mac-address-table notification command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches mac-add ress-table notification Command Modes Glob al co nfigu ration mode Usage Guidelines You can en able the MAC change no tification feature u sing th e mac-addres s-table notification change co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches mac-address-table static mac-address-table static To con figure the static M AC addresses fo r a VLAN interface o r dro p u nicast traffic for a MAC address for a VLAN interface, use the mac-address-table static comman d. To remove the static MAC addres s configuration s, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches macro apply cisco-desktop macro apply cisco-desktop To en ab le the Cisco-recommended features an d settings that are suitable for connectin g a switch port to a standard deskto p, use the macro apply cisco-deskto p comman d. macro apply cisco-desktop $AVID a cces s_vla nid Syntax Description $AVID access_vlanid Defaults This comman d has no default settings. Specifies an access VLAN ID.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches macro apply cisco-desktop Related Commands Command macro apply cisco-phone Descriptio n Enab les the Cisco-recommen ded features and settin gs th at are suitable for connecting a switch port to a standard d eskto p and a Cis co IP pho ne. macro apply cisco-router Enab les the Cisco-recommen ded features and settin gs th at are suitable for connecting a switch port to a ro uter.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches macro apply cisco-phone macro apply cisco-phone To en ab le the Cisco-recommended features an d settings that are suitable for connectin g a switch port to a standard deskto p and a Cisco IP pho ne, use th e ma cro apply cisco-phone comman d. macro apply cisco-phone $AVI D access_vlanid $VVID voice_ vlan id Syntax Description $AVID access_vlanid $VVID voice_vlanid Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches macro apply cisco-phone Related Commands Command macro apply cisco-deskto p Descriptio n Enab les the Cisco-recommen ded features and settin gs th at are suitable for connecting a switch port to a standard d eskto p. macro apply cisco-router Enab les the Cisco-recommen ded features and settin gs th at are suitable for connecting a switch port to a ro uter.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches macro apply cisco-router macro apply cisco-router To en ab le the Cisco-recommended features an d settings that are suitable for connectin g a switch port to a router, use the macro apply cisco-router command. macro a pply cisco -router $NVID na tive_vlanid Syntax Description $NVID native_vla nid Defaults This comman d has no default settings. Specifies a n ative VLAN ID.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches macro apply cisco-router Related Commands Command macro apply cisco-deskto p Descriptio n Enab les the Cisco-recommen ded features and settin gs th at are suitable for connecting a switch port to a standard d eskto p. macro apply cisco-phone Enab les the Cisco-recommen ded features and settin gs th at are suitable for connecting a switch port to a standard d eskto p and a Cis co IP pho ne.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches macro a pply cisco-switch macro apply cisco-switch To en ab le the Cisco-recommended features an d settings that are suitable for connectin g a switch port to an other switch, use the macro a pply cisco-switch command. macro a pply cisco -switch $NVID n ative_vlanid Syntax Description $NVID native_vla nid Defaults This comman d has no default settings. Specifies a native VLAN ID.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches macro apply cisco-switch Related Commands Command macro apply cisco-deskto p Descriptio n Enab les the Cisco-recommen ded features and settin gs th at are suitable for connecting a switch port to a standard d eskto p. macro apply cisco-phone Enab les the Cisco-recommen ded features and settin gs th at are suitable for connecting a switch port to a standard d eskto p and a Cis co IP pho ne.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches macro auto device macro auto device Use th e ma cro a uto device co mmand to simplify changing the p arameters fo r a built-in functions for a dev ice ty pe. Use the no fo rm of this command to rev ert to the intial parameter values. macro a uto device device_type [params values] no macro auto device device_ type [p arams values] Syntax Description device_ type Specifies the device type.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches macro auto device Command Description macro auto s ticky Specifies not to remove configuratio ns app lied by ASP acro ss lin k flaps and dev ice removal. shell trigger Creates a u ser defined trigger. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches macro auto execute (b uilt-in func tion) macro auto execute (built-in function) Use the macro auto execute configuration command to change built-in fun ction default values or to map user-defined triggers to built-in fun ction s and to pass the parameter values. Use th e no form of this co mmand to un map the trigger.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches macro auto execute (built-in function) Usage Guidelines The switch auto matically map s from builtin even t trig gers to builtin fun ction s. The builtin fu nctio ns are sy stem-defined fun ction s in the software image. Use th e macro a uto execute glob al configuration command to replace the builtin fu nctio n default valu es with values specific to your switch.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches macro auto execute (b uilt-in func tion) Related Commands Co mmand macro a uto device macro a uto ex ecute (remotely-defined trigger) macro a uto ex ecute (user-defined function) Descriptio n Simplifies chan ging the p arameters for a built-in fu nctio ns for a d evice typ e. Maps a trigger to a remotely defin ed functions. Maps a trigger to a u ser-defin ed function. macro a uto global processing Enables Auto Smartports on a switch.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches macro auto execute (remotely-defined trigger) macro auto execute (remotely-defined trigger) Use the macro a uto ex ecute con figuratio n command to map a trigg er to a remotely d efined function. Use the no form of this command to unmap the trigger. macro auto execute trigger_n ame remote url no macro auto execute trigger_name remote url Syntax Description trigg er_ name u rl Specifies the trigg er name.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches macro auto execute (user-defined func tion) macro auto execute (user-defined function) Use the macro auto execute configu ration command to map a trigger to a user-defined fun ction . Us e the no fo rm of this command to unmap th e trig ger.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches macro auto execute (user-defined function) exit fi if [[ $LINKUP -eq NO ]]; then conf t interface $INTERFACE no macro description $TRIGGER no switchport access vlan 1 if [[ $AUTH_ENABLED -eq NO ]]; then no switchport mode access fi no switchport port-security no switchport port-security maximum 1 no switchport port-security violation restrict no switchport port-security aging time 2 no switchport port-security aging type inactivity no sp
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches macro auto global processing macro auto global processing Use the macro auto glo ba l pro cessing global con figuratio n command to enab le Au to SmartPorts macros on the switch. Use the no fo rm of this command to d isab le Au to SmartPorts (ASP) macros globally. macro a uto global processing [cdp | lldp] no macro auto g lobal processing [ cdp | ldp] Note Syntax Description Starting with Release 15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches macro auto global processing The macro auto global processing cdp an d macro auto glo ba l processing lldp commands enables ASP g lobally if it is not already en abled, and set the fallback to CDP or LLDP, respectively. However, the no macro auto global processing [cdp | lldp] command only removes the fallback mechanism. It do es not d isable ASP g lobally; o nly the no ma cro auto global processing command disables ASP glob ally.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches macro auto mac-address-group macro auto mac-address-group Use th e ma cro a uto mac-a ddress-group co mmand to configu re a grou p o f MAC-address or OUIs as a trigg er. Use th e no form of this comman d to u nco nfigure the group. macro a uto ma c-address-group gr p_name no macro auto mac-a ddress-group grp_ namel Syntax Description grp_n ame Command Modes Glob al co nfigu ration Usage Guidelines Specifies the group name.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches macro auto monitor macro auto monitor To enable the device classifier, use th e macro auto monitor glo bal co nfigu ration command. Use the no form of this command to disable th e device classifier. macro auto monitor no macro auto monitor Syntax Description This command has no arguments or keywo rds. Command Default Device classifier is enabled.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches macro auto processing macro auto processing Note Only us e this co mmand when Auto SmartPorts (ASP) is enabled globally; when ASP is dis abled globally, interface-level co ntro l has no effect. Use the macro auto pro cessing interface config uration comman d to enable ASP macros on a specific interface. Use the no form of this command to disable ASP on a sp ecific interface before ASP is enabled globally.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches macro auto processing Command Description macro auto execute (remo tely-defined trigg er) macro auto execute (user-defined function) Maps a trigger to a remotely defined fun ction s. Maps a trigger to a user-defined fun ction . macro auto glo bal processing En ables Auto Smartports on a switch . Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches macro auto sticky macro auto sticky Use the macro auto sticky con figuratio n to s pecify not to remove config urations app lied by ASP across link flaps and device removal. macro a uto sticky Syntax Description This comman d has no argu ments or keyword s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches macro global apply cisco-global macro global apply cisco-global To ap ply the sys tem-defined defau lt template to the switch , use the macro global apply cisco-global g lobal configuration command on the switch stack or on a standalone switch. macro global apply cisco-global Syntax Description This command has no key words or variables. Defaults This command has no default setting .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches macro global apply system-cpp macro global apply system-cpp To apply the con trol plane p olicing d efault template to the switch , use the macro global apply system-cpp glo bal config uration comman d on the switch stack o r on a standalone switch. macro g lobal a pply system-cpp Syntax Description This comman d has no keywo rds or variables. Defaults This comman d has no default setting.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches macro global description macro global description To enter a d escrip tion abou t the macros that are applied to the switch, use the macro global description g lobal configuration command on the switch stack or on a standalone switch. Use th e no form o f this command to remove the description.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches main-cpu main-cpu To enter the main CPU submode an d manually synchronize the co nfigurations on the two superviso r en gines, use the main-cpu comman d. main-cpu Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings. Command Modes Redu ndancy mod e Usage Guidelines The main CPU submod e is used to manually synchronize the con figurations on the two s uperviso r en gines.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches match match To specify a match clau se by selecting one or more ACLs for a VLAN access-map s equ ence, use the match subcommand. To remove th e match claus e, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches match (class-map configura tion) match (class-map configuration) To define the match criteria for a class map, use the ma tch clas s-map con figuratio n command. To remove the match criteria, us e the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches match (class-map configuration) Usage Guidelines Before entering the match command, y ou must firs t en ter the class-map g lobal co nfigu ration command to specify the name of th e class who se match criteria you want to establish. The match comman d is used to sp ecify which fields in the packets are examin ed to classify the packets .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches match (class-map configura tion) This example shows h ow to specify a class-map that applies only to IPv6 traffic o n a Superv isor Eng ine 6-E: Switch# configure terminal Switch(config)# class-map match all ipv6 only Switch(config-cmap)# match dscp af21 Switch(config-cmap)# match protocol ipv6 Switch(config-cmap)# exit Switch# You can verify you r settin gs by entering the show class-map priv ileged EXEC command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches match flow ip match flow ip To sp ecify match criteria to treat flows with a uniq ue source or destination address as new flows, use the match flow ip co mmand . To d isab le this fu nctio n, use the no fo rm of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches match flow ip This examp le shows how to create a flow-based class map associated with a d estination address: Switch(config)# class-map match-all c1 Switch(config-cmap)# match flow ip destination-address Switch(config-cmap)# end Switch# Switch# show class-map c1 Class Map match-all c1 (id 2) Match flow ip destination-address Switch# Assu me there are two active flows on th e Fast Ethernet interface 6 /1 with source ad dresses 192.168 .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches match flow ip Switch(config-if)# end Switch# write memory Switch# show policy-map interface FastEthernet6/1 Service-policy input: p1 Class-map: c1 (match-all) 2965072 packets Match: flow ip destination-address police: Per-interface Conform: 6105636 bytes Exceed: 476652528 bytes Class-map: class-default (match-any) 0 packets Match: any 0 packets Switch# Assume th ere are two active flows as sh own below on the Fast Ethernet in terface 6/
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches match flow ip Switch# show class-map c1 Class Map match-all c1 (id 2) Match flow ip source-address ip destination-address ip protocol l4 source-port l4 destination-port Switch# show policy-map p1 Policy Map p1 Class c1 police 1000000 bps 9000 byte conform-action transmit exceed-action drop Switch# show policy-map interface FastEthernet6/1 Service-policy input: p1 Class-map: c1 (match-all) 15432182 packets Match: flow ip source-address ip d
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches mdix auto mdix auto To en able the automatic medium-dep en den t interface crossover (auto -MDIX) feature on the interface, u se the mdix auto comman d. When auto -MDIX is enabled , the in terface au tomatically d etects th e required cable co nnection typ e (straight-thro ugh or cro ssover) and config ures the connection appropriately. Use the no form of th is command to disable auto-MDIX.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches mdix auto Co mmand Description show interfaces capabilities Displays the interface capabilities for an interface o r fo r all the interfaces on a switch. Displays the interface status. show interfaces status Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches media-type media-type To select th e connecto r fo r a du al-mode capab le port, us e the media-type co mmand . media-type {rj45 | sfp} Syntax Description rj45 sfp Defaults sfp Command Modes Usage Guidelines Uses the RJ-45 conn ector. Uses the SFP co nnector. Interface configuration mod e This command is supp orted on all po rts on the WS-X4306 -GB-T modu le an d ports 1/4 5-4 8 o n the WS-X4948 chassis.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches mode mode To set the redu ndancy mod e, use the mode command. mode {rpr | sso } Syntax Description rpr sso Defaults If you are up grading the cu rren t su pervisor eng ine from Cisco IOS Release 12.2(18)EW o r an earlier release to 12.2(20)EWA, and the RPR mod e has been saved to the startup configuration , b oth sup ervisor en gines will contin ue to operate in RPR mode after the software u pgrade.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches mode Command Descriptio n show redundancy show running-co nfig Displays redund ancy facility informatio n. Displays the running configuration of a switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches monitor capture {access-list | class-map} monitor capture {access-list | class-map} To specify an access list or clas s map as the co re filter, use the monitor capture {access -list | cla ss-map} command. To remove the filter, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches monitor capture [clear | export] monitor capture [clear | export] To clear cap tu re buffer con tents or to sto re the packets to a file, use the monitor capture [clea r | export filename] command. monitor capture name [clea r] [export filename] Syntax Description n ame clear Specifies a cap ture point. Clears all the packets in the capture buffer. export filen ame Store all the p ackets in capture buffer to a .pcap file.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches monitor ca pture [interface | vlan | control-plane] monitor capture [interface | vlan | control-plane] To specify on e or more attachment points with d irectio n, use the monito r ca pture [interface | vla n | co ntro l-plane] command. To remove the attachment point, use th e no form o f this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches monitor capture file location buffer-size monitor capture file location buffer-size To specify the capture destinatio n, use the monitor capture command. To remove the details, use the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches monitor capture file location buffer-size If the cap ture destination is a buffer, you mu st use the show comman d to d ecode and display the packets from the buffer. If the circular op tion is s pecified, capture continues until you explicitly is sue the sto p co mmand . If no space exists in the buffer, oldest p acket(s) are removed to accommodate the new on es.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches monitor capture file location buffer-size Source: 00:00:00:00:03:01 (00:00:00:00:03:01) Address: 00:00:00:00:03:01 (00:00:00:00:03:01) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default) … Switch# sh monitor capture mycap buffer dump 0.000000 10.1.1.164 -> 20.1.1.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches monitor capture limit monitor capture limit To specify cap ture limits, use the monitor capture limit comman d. To remove the limits, use the no form of this comman d. monitor capture name limit {duration seconds] [packet-leng th size] [packets n um] no monitor capture name limit [duration] [packet-length] [packets ] Syntax Description name duration seconds Specifies a capture poin t. Specifies du ration in second s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches monitor capture mycap match monitor capture mycap match To define an ex pliciti in-line core filter, u se the monitor capture mycap match command. To remove it, use th e no form o f this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches monitor capture mycap match Usage Guidelines You can sp ecify the co re filter as a class map, access list, or an explicit in-lin e filter. If the filter has already been specified wh en yo u enter this comman d, it replaces the o lder one. The explicit, in -line filter is in tend ed as a simple way to sp ecify a core filter.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches monitor capture start monitor capture start To start or stop a capture poin t, use the monitor ca pture command. monitor capture name start [capture-filter filter-string] [display [display-filter filter-strin g]] [brief | detailed | dump | stop] Syntax Description n ame start Specifies a cap ture point. Starts th e Wiresh ark ses sion an d captures live traffic. capture-filter filter-str in g Specifies the capture filter.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches monitor capture start 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 10.1.1.13 -> 20.1.1.2 10.1.1.14 -> 20.1.1.2 10.1.1.15 -> 20.1.1.2 10.1.1.16 -> 20.1.1.2 10.1.1.17 -> 20.1.1.2 10.1.1.18 -> 20.1.1.2 10.1.1.19 -> 20.1.1.2 10.1.1.20 -> 20.1.1.2 10.1.1.21 -> 20.1.1.2 10.1.1.22 -> 20.1.1.2 10.1.1.23 -> 20.1.1.2 10.1.1.24 -> 20.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches monitor capture start .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default) Source: 00:00:00:00:03:01 (00:00:00:00:03:01) Address: 00:00:00:00:03:01 (00:00:00:00:03:01) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default) Switch# monitor capture mycap start capture-filter "udp.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches monitor capture start 0060 0070 0080 0090 00a0 00b0 00c0 00d0 00e0 00f0 36 37 38 39 3a 3b 3c 3d 3e 3f 40 41 42 43 44 45 46 47 48 49 4a 4b 4c 4d 4e 4f 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f 60 61 62 63 64 65 66 67 68 69 6a 6b 6c 6d 6e 6f 70 71 72 73 74 75 76 77 78 79 7a 7b 7c 7d 7e 7f 80 81 82 83 84 85 86 87 88 89 8a 8b 8c 8d 8e 8f 90 91 92 93 94 95 96 97 98 99 9a 9b 9c 9d 9e 9f a0 a1 a2 a3 a4 a5 a6 a7 a8 a9 aa ab ac ad ae af b0 b
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches monitor capture start Frame Number: 1 Frame Length: 256 bytes (2048 bits) Capture Length: 256 bytes (2048 bits) [Frame is marked: False] [Frame is ignored: False] [Protocols in frame: eth:ip:udp:data] Ethernet II, Src: 00:00:00:00:03:01 (00:00:00:00:03:01), Dst: 54:75:d0:3a:85:3f (54:75:d0:3a:85:3f) Destination: 54:75:d0:3a:85:3f (54:75:d0:3a:85:3f) Address: 54:75:d0:3a:85:3f (54:75:d0:3a:85:3f) .... ...0 .... .... .... ....
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches monitor session monitor session To enable the SPAN ses sions on interfaces o r VLANs, use th e mo nitor s essio n command. To remove one o r more source or d estination interfaces from a SPAN session, or a so urce VLAN from a SPAN ses sion, u se the no form of this command .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches monitor session learning (Optional) Enables host learning on ingress-enabled destinatio n ports. remote vlan vla n_id so urce Port-channel interface-numb er cpu Specifies an RSPAN so urce or destinatio n s essio n o n a switch. Specifies a SPAN so urce. Specifies a po rt-ch ann el in terface; valid values are from 1 to 64. Cau ses traffic received or sen t from the CPU to be copied to the destination of the sessio n.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches monitor session l3-forward (Optio nal) Layer 3 p ackets. forward Specifies special Layer 3 fo rwards tunnel encapsulation. glean receive Specifies special Layer 3 fo rwards glean. Specifies packets address ed to a po rt. co ntro l-packet (Optio nal) ESMP packets. (Optio nal) Outpu t Layer 3 interface MTU exceeded . Specifies Layer 3 routed packets. Specifies packets address ed to a po rt.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches monitor session Usage Guidelines Only one SPAN destinatio n for a SPAN session is supported. If you attemp t to add another destination in terface to a session th at already has a destination interface that is config ured, you will get an error. You mu st first remove a SPAN destination interface befo re changin g th e SPAN destination to a different in terface. Beginning in Cisco IOS Release 12 .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches monitor session This examp le shows how to configure the sources with different directio ns within a SPAN sessio n: Switch# configure terminal Switch(config)# monitor session 1 source interface fa2/3 rx Switch(config)# monitor session 1 source interface fa2/2 tx Switch(config)# end This examp le shows how to remove a so urce interface from a SPAN session: Switch# configure terminal Switch(config)# no monitor session 1 source interface fa2
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches mtu mtu To en able jumbo frames on an interface by adjusting the maximu m size o f a packet or maximum tran smission unit (MTU), use the mtu command. To retu rn to the default setting , use the no form of this command. mtu bytes no mtu Syntax Description Defaults b ytes Byte size; valid values are from 1500 to 91 98.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches na me name To set the MST region name, use the name comman d. To return to the defau lt name, use the no form of this co mmand . name name no name na me Syntax Description name Specifies th e name of the MST region . The n ame can b e any string with a max imu m len gth of 32 characters. Defaults The MST reg ion name is not set.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches nmsp nmsp To con figure Network M obility Serv ices Protocol (NMSP) on the switch, us e the nmsp command. This command is available o nly when your s witch is running the cryptographic (en crypted) software image. Use the no form of this command to return to the default setting.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches nmsp attachment suppress nmsp attachment suppress To sup press reporting attachment information from a specified interface, u se the nmsp attachment suppress interface command. This co mmand is available on ly when your s witch is running th e cryptog raphic (encrypted) software image. Use the no fo rm of this command to report attachment information.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches pagp learn-method pagp learn-method To learn the input in terface o f the in comin g pack ets, us e th e pagp learn-method command. To return to th e default value, u se the no form of this command. pagp learn-method {aggregatio n-port | physical-po rt} no pagp learn-method Syntax Description a ggregation-port Specifies learning the address o n th e port channel.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches pagp port-priority pagp port-priority To select a port in h ot s tand by mode, use the pagp port-priority command. To return to the default value, use th e no form of this command . pagp port-prio rity priority no pagp port-priority Syntax Description priority Defaults Port priority is set to 12 8. Command Modes Interface con figuration mode Port priority nu mber; valid values are from 1 to 2 55.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches passive-interface passive-interface To dis able sending ro uting u pdates o n an interface, use the passive-interface comman d. To reen ab le th e sendin g of ro uting upd ates, us e the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches passive-interface You can not specify both a macro an d an interface range in the same command. After creating a macro, you can enter ad ditional ranges. If you have alread y entered an interface range, th e CLI do es not allow you to enter a macro. You can sp ecify a single in terface in the range ran ge value. This makes the co mmand similar to the passive-interface interface-nu mber command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches passive-interface Switch(config-router)# no passive-interface ethernet0 Switch(config-router)# network 10.108.0.1 0.0.0.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches permit permit To permit an ARP p acket based on matches against the DHCP binding s, use the permit comman d. To remove a specified ACE from an access list, us e the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches permit Usage Guidelines Examples Permit clauses can be add ed to forward or drop ARP packets bas ed on some matching criteria. This example s hows a ho st with a MAC add ress of 00 00.0000.abcd and an IP ad dress of 1.1.1.1. This example shows how to permit both requ ests and respon ses from this host: Switch(config)# arp access-list static-hosts Switch(config-arp-nacl)# permit ip host 1.1.1.1 mac host 0000.0000.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches police police To configu re the Traffic Policing feature, use th e police QoS po licy-map class config uration co mmand . To remove the Traffic Policing feature from the configuration, use th e no form of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches police Traffic p olicin g will not be executed for traffic that passes throu gh an interface. S pecifying Multiple Actions The police co mmand allows you to specify multiple policing actio ns. When sp ecify ing multiple policing actions when configu ring the police command, note the following po ints: • You can specify a maximum of four actions at on e time.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches police The token arrival rate is calculated as fo llows: (time between pack ets * policer rate)/8 bytes Examples • If th e numb er o f bytes in th e co nfo rm bucket - B is greater th an or equ al to 0, th e packet co nforms an d the conform action is tak en on the packet. If the packet conforms , B bytes are removed from the co nfo rm bucket and the conform actio n is taken.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches police Switch(config-pmap-c)# police 8000 1000 1000 conform-action transmit exceed-action set-qos-transmit 1 violate-action drop Switch(config-pmap-c)# exit Switch(config-pmap)# exit Switch(config)# interface gigabitethernet 6/1 Switch(config-if)# service-policy output police-setting Switch(config-if)# end In this example, the initial to ken buckets starts full at 1000 bytes .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches p olice (percent) police (percent) To co nfigu re traffic policing o n the b asis of a percen tage o f ban dwidth availab le on an interface, u se the police command in Qo S policy-map clas s configuration mod e. To remove traffic policing from the co nfiguration, u se the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches police (percent) Command Modes Policy-map class config uration mode Usage Guidelines This command calculates the CIR an d PIR on th e basis of a p ercentage o f the maximum amount of b and width available o n the interface.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches police rate police rate To con figure s ingle or d ual rate p olicer, use the police rate command in po licy-map con figuration mode. To remove traffic policing from the configuration , use the no form of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches police rate Command Modes Usage Guidelines Policy-map config uration mode Use the po lice rate command to limit traffic o n th e basis of pps , bps, or a percentage of interface b and width. If the police rate co mmand is issued, but the a rate is not specified, traffic that is destined will be p oliced o n th e basis of bps .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches police (two rate s) police (two rates) To config ure traffic policing using two rates, the committed in formatio n rate (CIR) and the peak information rate (PIR), use the police comman d in policy-map con figuratio n mod e. To remo ve two-rate traffic policing from the configuration , use the no form of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches police (two rates) Usage Guidelines Refer to RFC 2 698-Two Rate Th ree Color Marker. Two-rate traffic p olicin g uses two to ken buckets—Tc an d Tp—for policing traffic at two independent rates. Note the following po ints abo ut th e two token buckets : • The Tc token buck et is updated at the CIR value each time a packet arrives at the two-rate policer. The Tc token buck et can contain up to the confirm burst (Bc) value.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches police (two rate s) Figure 2-1 Marking Packets and Assigning Actions with the Two-Rate Policer PIR CIR Be B > Tp No Bc B > Tc No Packet of size B Yes Violate Exceed Conform Action Action Action 60515 Yes Examples This examp le shows how to configure two-rate traffic policing on a class to limit traffic to an averag e co mmitted rate o f 500 kb ps and a peak rate o f 1 Mbps: Switch# configure terminal Enter configuration
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches police (two rates) Service-policy output: policy1 Class-map: police (match all) 148803 packets, 36605538 bytes 30 second offered rate 1249000 bps, drop rate 249000 bps Match: access-group 101 police: cir 500000 bps, conform-burst 10000, pir 1000000, peak-burst 100000 conformed 59538 packets, 14646348 bytes; action: transmit exceeded 59538 packets, 14646348 bytes; action: set-prec-transmit 2 violated 29731 packets, 7313826 bytes; action:
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches policy-map policy-map To create or mo dify a p olicy map that can b e attached to mu ltip le ports to specify a service po licy and to enter po licy-map configuration mod e, use th e policy -map g lo bal configuration command. To delete an existing policy map and to return to global configuratio n mo de, use th e no form of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches policy-map Switch(config-pmap-c)# exit Switch(config-pmap)# class class3 Switch(config-pmap-c)# set dscp cs3 Switch(config-pmap-c)# exit Switch# This example s hows how to delete the po licy map called po licymap2: Switch# configure terminal Switch(config)# no policy-map policymap2 Switch# You can verify your settings by entering the show policy -map privileg ed EXEC command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches port-channel load-balance port-channel load-balance To set the load-distrib ution meth od amon g the ports in the bu ndle, use the port-channel load-balance co mmand . To reset the load distribution to the default, use the no fo rm of this command. port-channel load-balance method no port-cha nnel lo ad-balance Syntax Description method Specifies the load distribution meth od. See the “Usag e Gu idelin es” section for more information.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches port-channel standalone-disable port-channel standalone-disable To disab le the EtherChannel stand alon e optio n in a port channel, use the port-channel standalone-disable comman d in in terface config uration mode. To enable this option, use th e no fo rm o f this co mmand . port-channel s tandalone-disable no port-channel standalone-dis able Syntax Description This command has no arguments or keywo rds.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches port-security mac-address port-security mac-address To config ure a secu re add ress on an interface for a specific VLAN or VLAN rang e, use the port-security mac-address command. port-security mac-address mac_ address Syntax Description mac_ad dress Command Modes VLAN-range interface sub mode Usage Guidelines Examples The M AC-address that needs to be secured.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches port-security mac-address sticky port-security mac-address sticky To co nfigure a sticky address o n an interface for a specific VLAN or VLAN range, u se the port-security mac-address sticky command. port-security mac-address sticky mac_address Syntax Description mac_address Command Modes VLAN-range in terface submod e Usage Guidelines Usage Guidelines The MAC-add ress that needs to b e secu red.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches p ort-security maximum port-security maximum To config ure the maximum number o f ad dresses on an interface for a specific VLAN or VLAN range, use th e port-security max imum command. port-security maximum ma x_value Syntax Description max_value Command Modes VLAN-range interface sub mode Usage Guidelines The maximum nu mb er of MAC-add resses .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches power dc input power dc input To configure th e p ower DC inpu t parameters on th e s witch, use the power dc input command. To return to the default p ower settings, u se the no form of this command. power dc input watts no power dc input Syntax Description watts Sets the total capacity of the external DC so urce in watts; valid values are from 300 to 850 0. Defaults DC p ower input is 2500 W.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches power efficient-ethernet auto power efficient-ethernet auto To enable EEE, u se the power efficient-ethernet auto command. To disable EEE, use th e no form o f this co mmand . power efficient-ethernet auto no power efficient-ethernet auto Syntax Description This comman d has no argu ments or keyword s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches power inline power inline To set the inline-power state for the inline-po wer-capable interfaces, use the po wer inline co mmand . To retu rn to the defau lt values, use the no fo rm of this command. power inline { a uto [max milliwatt] | never | static [max milliwatt] | cons umption milliwatt} no power inline Syntax Description a uto max milliwatt Sets th e Power over Ethernet state to auto mode for in line-power-capable in terfaces.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches power inline This examp le shows how to d isable the inlin e-power detection and power for th e inline-p ower-capable interfaces: Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches power inline consumption power inline consumption To set the default power that is allocated to an in terface fo r all the inline-po wer-capable interfaces on th e switch, use the power inline consumption co mmand . To return to the default values, u se the no form o f this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches power inline four-pair forced power inline four-pair forced To automatically enable p ower on b oth signal and spare pairs from a switch po rt, prov ided th e end-dev ice is PoE capab le o n both signal and spare p airs but do es not sup port the CDP or LLDP extensions required for UPOE, use the power inline fo ur-pair forced command. power inline four-pair fo rced Syntax Description This comman d has no argu ments or keyword s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches power inline logging global power inline logging global To en able co nsole messages th at show when a Po E device h as been d etected and to show wh en a PoE d evice has been removed, use the po wer inline logging global comman d. power inline lo gging global Syntax Description This command has no arguments or keywo rds.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches power inline police power inline police To config ure Power over Ethern et policing on a p articular in terface, u se the power inline po lice co mmand . The no form o f the command disables PoE po licing o n an interface.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches power inline police Related Commands Command errdisable recovery Descriptio n Enab les errdisable autorecovery; the port automatically restarts itself after go ing to the errdisable state after its errdisable autorecovery timer expires. show power inline police Displays the PoE policing status of an interface, module, o r chassis. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches power redundancy-mode power redundancy-mode To config ure the power settings for the chassis, u se the power redundancy-mo de command. To return to the default setting, u se the default form o f this co mmand . power redundancy-mode {redundant | combined} default power redundancy-mode Syntax Description Defaults redundant co mbined Con figures the switch to redund ant power managemen t mo de.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches power redundancy-mode Command Descriptio n show power Displays info rmation ab out the power status . Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches pp poe intermediate-agent (global) pppoe intermediate-agent (global) To en able th e PPPoE Intermediate Ag ent feature on a switch, u se the pppoe intermediate-agent glo bal co nfiguration co mmand . To d is able the feature, use th e no form o f this co mmand . pppoe intermediate-agent no pppoe intermediate-agent Syntax Description This comman d has no argu ments or keyword s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches pppoe intermediate-agent (interface) pppoe intermediate-agent (interface) Note This command takes effect only if yo u enable th e pppoe intermediate-agent glob al comman d. To enable the PPPoE Intermediate Agent feature on an interface, use the pppoe intermediate-agent command. To disable th e feature, u se the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches pppoe intermediate-agent (interface vla n-range) pppoe intermediate-agent (interface vlan-range) Note This comman d takes effect only if you en able the pppoe intermediate-agent g lobal command. To enable PPPo E Intermediate Ag ent on an interface VLAN rang e, use the pppoe intermediate-agent global command. To dis able the feature, use th e no form o f this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches pppoe intermediate-agent format-type (global) pppoe intermediate-agent format-type (global) To set the access nod e identifier, g eneric error message, an d id entifier string for the switch, u se the pppoe intermediate-agent format-type (global) command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches pppoe inte rmediate-age nt format-type (global) Examples This examp le shows how to set an access-node-id entifier: Switch(config)# pppoe intermediate-agent format-type access-node-identifier string switch-abc-123 This examp le shows how to u nset a gen eric-error-message: Switch(config)# no pppoe intermediate-agent format-type generic-error-message Related Commands Co mmand show pppoe intermediate-agent interface Description Displays
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches pppoe intermediate-agent format-type (interface) pppoe intermediate-agent format-type (interface) Note This command takes effect only if yo u enable th e pppoe intermediate-agent interface configuration command. To set circuit-id o r remote-id for an interface, use th e pppoe intermediate-agent format-type command. To unset the parameters, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches pppoe intermediate-agent format-type (interface vla n-range) pppoe intermediate-agent format-type (interface vlan-range) Note This comman d takes effect only if you en able the pppoe intermediate-agent in terface vlan-range co nfiguration mode command. To set circu it-id or remo te-id for an interface vlan -rang e, use the pppoe intermediate-a gent fo rmat-ty pe in terface v lan-range mo de command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches pppoe intermediate-agent limit rate pppoe intermediate-agent limit rate To limit the rate of the PPPoE Discovery packets arriving on an interface, use the pppoe intermediate-agent limit rate comman d. To d isab le the feature, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches pppoe intermediate-agent tru st pppoe intermediate-agent trust To set the trus t co nfigu ration o f an in terface, use the pppoe intermediate-agent trust g lobal comman d. To un set the trust parameter, use the no form o f this co mmand . pppoe intermediate-agent trust no pppoe intermediate-agent trus t Syntax Description This comman d has no argu ments or keyword s. Defaults All interfaces are untrusted.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches pppoe intermediate-agent vendor-tag strip pppoe intermediate-agent vendor-tag strip Note This command takes effect only if yo u enable th e pppoe intermediate-agent interface configuration command and the pppoe intermediate-agent trust command. To en able ven dor-tag strippin g o n PPPoE Discovery packets from PPPo E Server (or BRAS), us e the pppoe intermediate-agent vendor-tag strip co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches priority priority To en able th e strict priority qu eue (low-latency qu eueing [LLQ]) an d to give prio rity to a class of traffic belonging to a p olicy map attached to a p hysical port, u se the priority policy-map clas s configuration co mmand . To return to the defau lt setting, use th e no form o f this co mmand . priority no priority Syntax Description This comman d has no argu ments or keyword s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches priority Related Commands Command bandwidth class dbl Descriptio n Specifies or modifies the minimum b and width prov ided to a class b elon ging to a policy map attached to a phy sical port. Specifies the name of th e class wh ose traffic p olicy you want to create or change. Enab les dyn amic buffer limitin g for traffic h itting this class.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches private-vlan private-vlan To config ure private VLANs and the associatio n b etween a private VLAN and a secondary VLAN, use the private-vlan command. To return to the default valu e, use the no form o f this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches private-vlan An isolated VLAN is a VLAN that is used by the isolated ports to communicate with the pro miscuo us p orts. The isolated VLAN traffic is blocked on all other p rivate ports in the same VLAN and can be received only by the standard tru nking po rts an d the promiscuous ports that are ass igned to th e correspon ding primary VLAN.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches private-vlan 303 440 community isolated This examp le shows how to create a p rivate VLAN relationsh ip among the primary VLAN 14, the isolated VLAN 1 9, and community VLANs 20 and 21 : Switch(config)# vlan 19 Switch(config-vlan) # private-vlan isolated Switch(config)# vlan 14 Switch(config-vlan)# private-vlan primary Switch(config-vlan)# private-vlan association 19 This examp le shows how to remove a private VLAN relationship and delet
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches private-vlan This example s hows how to config ure interface FastEthernet 5 /1 as a PVLAN ho st p ort and verify th e configuration : Switch# configure terminal Switch(config)# interface fastethernet 5/1 Switch(config-if)# switchport mode private-vlan host Switch(config-if)# switchport private-vlan host-association 202 440 Switch(co nfig-if)# end Switch# show interfaces fastethernet 5/1 switchport Name: Fa5/1 Switchport: Enabled Adminis
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches private-vlan mapping private-vlan mapping To create a mapp ing between the primary and th e secondary VLANs so that both share the same primary VLAN SVI, u se the private-vla n mapping command. To remove all PVLAN mappings from an SVI, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches private-vlan mapping Switch(config)# interface vlan 202 Switch(config-if)# private-vlan mapping add 303-307,309,440 Switch(config-if)# end Switch# show interfaces private-vlan mapping Interface Secondary VLAN Type --------- -------------- ----------------vlan202 303 isolated vlan202 304 isolated vlan202 305 isolated vlan202 306 isolated vlan202 307 isolated vlan202 309 isolated vlan202 440 isolated Switch# This example shows the disp la
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches p rivate-vlan synchronize private-vlan synchronize To map the secondary VLANs to th e same instance as th e primary VLAN, use the private-vlan synchronize command. private-vlan synchronize Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches profile profile To enter profile call-home configuration submo de, u se the profile co mmand in call-ho me co nfiguration mo de, use th e profile command . profile p rofile_name Syntax Description p rofile_name Defaults This command has no default setting s. Specifies the profile n ame.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches profile Related Commands Co mmand destination address destina tion preferred-msg -format Description Config ures the d estination e-mail add ress or URL to which Call Ho me mes sages will be s ent. Config ures a maximum des tinatio n message size for th e destinatio n profile. Config ures a preferred message format. destination transport-method subscribe-to-alert-g roup a ll Enables th e messag e transp ort method.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches qos account layer-all encapsulation qos account layer-all encapsulation To accou nt fo r Lay er 1 header length of 20 bytes in QoS p olicing features, use the qos a ccount lay er-all enca psulation command. To disable the use of additional bytes, use the no fo rm of this command. qos account la yer-all encapsulation no qos account layer-all encapsulation Syntax Description This command has no arguments or keywo rds.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches qos accou nt layer2 encapsulatio n qos account layer2 encapsulation To include ad ditional by tes to be acco unted by th e QoS features, use the qo s a ccount layer2 encapsulation comman d. To disab le the u se of add itio nal bytes, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches qos account layer2 encapsulatio n Related Commands Command show interfa ces Descriptio n Displays traffic on a specific interface. switchport Mo difies the switchin g characteristics of a Layer 2 switch in terface. switchport block Prevents the un known multicast o r unicas t packets from being forwarded. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches qos tru st qos trust To set the trusted state o f an in terface (for examp le, whether the p ackets arriving at an interface are trus ted to carry the correct CoS, ToS, an d DSCP classifications), use th e qos trus t command. To set an interface to the u ntru sted state, use the no form of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches qos trust This example s hows how to set th e tru sted state of an interface to DSCP: Switch(config-if)# qos trust dscp Switch(config-if)# This example s hows how to set th e PVID CoS level to 6: Switch(config-if)# qos trust extend cos 6 Switch(config-if)# This example s hows how to set th e Cisco p hone as the trust dev ice: Switch(config-if)# qos trust device cisco-phone Switch(config-if)# Related Commands Command queue-limit Desc
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches queue-limit queue-limit To specify or mod ify the maximum number of p ackets the queue can ho ld for a class p olicy config ured in a policy map, use the queue-limit command. To remove th e queue p acket limit from a class, use the no form o f this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches queue-limit Related Commands Command bandwidth class policy-map shape (class-bas ed queueing) Descriptio n Specifies or modifies the minimum b and width prov ided to a class b elon ging to a policy map attached to a phy sical port. Specifies the name of th e class wh ose traffic p olicy you want to create or change.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches re dundancy redundancy To en ter the redundancy configuration mode, use the redundancy command in th e global config uration mode. redundancy Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings. Command Modes Glob al co nfigu ration mode Usage Guidelines The redund ancy co nfiguration mode is used to enter the main CPU su bmode.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches redundancy config-sync mismatched-commands redundancy config-sync mismatched-commands To move the active su pervisor engine into the Mismatch ed Comman d List (MCL) and resets the stan dby su pervisor en gine, use the redundancy config-sync mismatched-commands command. If your active and stan dby su pervisors engines are running different versions of Cis co IOS, some of their CLIs will not be compatible.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches redundancy config-sync mismatched-commands If SSO mod e cann ot b e establish ed between the active and standby su pervisor eng ines becau se of an incompatibility in th e configu ration file, a mis matched command list (MCL) is gen erated at the active superv isor engine and a reload into RPR mo de is forced for th e stan dby superviso r eng ine.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches redundancy force-switchover redundancy force-switchover To force a switch over from th e active to the stan dby superv isor engine, u se the redundancy force-switcho ver command. redundancy force-switchover Syntax Description This command has no arguments or keywo rds. Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches redundancy reload redundancy reload To force a reload of one or bo th s uperviso r en gines, use the redunda ncy reload co mmand . redundancy reload {peer | shelf} Syntax Description peer shelf Defaults This comman d has no default settings. Command Modes Usage Guidelines Reload s th e peer unit. Reboots both su pervisor eng ines .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches remote login module remote login module To remotely con nect to a specific mod ule, use th e remo te login module configu ration co mmand . remote login module mod Syntax Description mod Defaults This command has no default setting s. Command Modes Usage Guidelines Targ et module for the command. Priv ileged EXEC mo de This command applies only to the Access Gateway Module on Catalyst 4500 series switches.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches remote-span remote-span To convert a VLAN into an RSPAN VLAN, use th e remote-s pan comman d. To convert an RSPAN VLAN to a VLAN, use the no fo rm of this command. remote-span no remote-span Syntax Description This comman d has no argu ments or keyword s. Defaults RSPAN is disabled.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches renew ip dhcp snooping database renew ip dhcp snooping database To renew the DHCP bin ding datab ase, u se the renew ip dhcp snooping da tabase co mmand . renew ip dhcp snooping database [validation no ne] [url] Syntax Description va lida tion no ne Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches rep ad min vlan rep admin vlan Use the rep admin vlan glob al configuration command to co nfigure a Resilien t Ethern et Pro tocol (REP) ad ministrative VLAN for REP to transmit hardware flo od layer (HFL) messag es. Us e the no form of this co mmand to return to the default config uration with VLAN 1 as the administrative VLAN. rep admin vla n vlan-id no rep admin vlan Syntax Description vla n-id Th e VLAN ID range is from 1 to 40 94.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches rep block port rep block port Use the rep block port interface configuratio n command on the REP primary edge port to configu re Resilient Eth ernet Pro to co l (REP) VLAN lo ad balancing. Use the no fo rm of this command to retu rn to th e default con figuratio n.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches rep block port Neighbor Offset Numbers in a REP Segment Uplink switch C Forwarding (51-100) Forwarding (1-50) gi2/0/6 gi2/0/8 Switch A Note 201398 Figure 2-2 Uplink switch B You wo uld never enter an o ffs et valu e of 1 becau se that is the offset nu mber of the primary edge port itself.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches rep block port Port Role: Open Blocked Vlan: Admin-vlan: 1 Preempt Delay Timer: 35 sec Load-balancing block port: none Load-balancing block vlan: none STCN Propagate to: PDU/TLV statistics: LSL PDU rx: 107122, tx: 192493 Switch B# config t Switch (config)# interface gigabitethernet1/0/1 Switch (config-if)# rep block port id 0080001647FB1780 vlan 1-100 Switch (config-if)# exit This examp le sh ows how to configure VLAN load b ala
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches rep lsl-a ge-timer rep lsl-age-timer Use the rep lsl-age-timer interface config uration command on a Resilien t Ethern et Protocol (REP) port to con figure the Link Statu s Lay er (LSL) age timer for th e time period that the REP in terface remain s up witho ut receiving a hello from the REP neighbo r. Use the no form of th is command to return to the default time.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches rep preempt delay rep preempt delay Use the rep preempt delay interface con figuratio n co mmand on the REP primary edge port to configure a waiting period after a s egment port failu re and recovery befo re Resilient Ethernet Protocol (REP) VLAN load b alancing is triggered. Use the no form of this comman d to remove the con figured delay.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches rep preempt segment rep preempt segment Use the rep preempt segment p rivileg ed EXEC co mmand to manually start Resilient Ethernet Pro toco l (REP) VLAN load b alancing on a segment. rep preempt segment segment_id Syntax Description segmen t-id Defaults Man ual preemptio n is the default b ehavior. Command Modes Usage Guidelines ID of the REP segment. The ran ge is from 1 to 1024.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches rep segment rep segment Use the rep segment interface co nfiguration command to enab le Resilient Eth ernet Pro toco l (REP) on th e interface and to as sign a segmen t ID to it. Use the no form of this command to disable REP on the in terface. rep segment segment-id [edge [no-neighbor] [primary]] [preferred] no rep segment Syntax Description segment-id Assig n a seg ment ID to the interface. Th e range is from 1 to 10 24.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches rep segment • REP p orts follow these rules: – There is n o limit to the nu mber of REP ports on a switch; h owever, only two ports o n a switch can belong to the same REP segmen t. – If only one port on a switch is configured in a segment, the port sh ould be an edge p ort.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches rep segment Related Commands Command show interfa ces rep [detail] show rep to po logy [detail] Descriptio n Displays REP configuration and status for all interfaces or the sp ecified in terface. Displays information about all ports in the seg ment, including which one was configured and selected as the primary edge p ort. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches rep stcn rep stcn Use the rep stcn interface con figuratio n command on a Resilien t Eth ernet Protocol (REP) edge p ort to co nfigure the port to sen d REP seg ment topolo gy change notificatio ns (STCNs) to another interface, to other segmen ts, or to Spanning Tree Proto col (STP) network s. Use the no form of th is command to disable the sen ding of STCNs to the interface, seg ment, or STP network.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches reset reset To leave the pro posed new VLAN database but remain in VLAN configu ration mode and res et the p ropo sed new datab ase to be identical to the VLAN database currently implemen ted, use th e reset command. res et Syntax Description This command has no arguments or keywo rds. Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches revision revision To s et the MST config uration revisio n number, use the rev ision command. To return to the default settings, use the no form of this command. revision version no revision Syntax Description version Defaults Revision version is s et to 0. Configuration revis io n number; valid values are from 0 to 6553 5.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches service-policy (interface configuration) service-policy (interface configuration) To attach a policy map to an in terface or to apply different QoS policies on VLANs that an interface b elon gs to, use the service-po licy command. To remove a po licy map from an interface, use the no form o f this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches servic e-policy (interface configura tion) Switch(config-if-vlan-range)# exit Switch(config-if)# vlan-range 300-301 Switch(config-if-vlan-range)# service-policy output p2 Switch(config-if-vlan-range)# end Switch# show policy-map interface gigabitEthernet 6/1 vlan 20 GigabitEthernet6/1 vlan 20 Service-policy input: p1 Class-map: class-default (match-any) 0 packets Match: any 0 packets police: Per-interface Conform: 0 bytes Exceed: 0 bytes S
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches service-policy (interface configuration) Switch(config)#vlan configuration 20 Switch(config-vlan-config)#service-policy out policy-vlan Switch(config-vlan-config)#end Switch# Related Commands Command class-ma p Descriptio n Creates a class map to be used for matching packets to the class whose name you specify and to enter class-map co nfiguration mo de.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches service-policy (policy-map class) service-policy (policy-map class) To create a serv ice policy th at is a quality of service (QoS) policy within a po licy map (called a hierarchical service po licy), u se th e service-po licy p olicy-map class configuration command. To disable the service policy within a po licy map, use the no fo rm of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches service-policy (policy-map class) Related Commands Command bandwidth class dbl Descriptio n Creates a signaling class structu re th at can be referred to b y its n ame. Specifies the name of th e class wh ose traffic p olicy you want to create or change. Enab les active qu eue managemen t on a tran smit qu eue used by a class o f traffic.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches se rvice-polic y input (control-plane) service-policy input (control-plane) To attach a po licy map to a co ntrol plane for aggreg ate con trol plane services, use the service-policy input command. Use the no form o f this co mmand to remove a service p olicy from a control plane.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches service-policy input (control-plane) Related Commands Command control-pla ne Descriptio n Enters co ntro l-plane configuration mod e. macro global apply sy stem-cpp Applies th e contro l plane policing defau lt template to the switch. policy-map Creates a policy map that can be attached to multiple po rts to sp ecify a service policy an d to enter policy-map config uration mo de.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches session module session module Note This comman d is on ly supported in SSO mode an d d oes no t work in RPR mod e. To log in to the s tand by sup ervisor engine usin g a virtual co nsole, use the session module configuration co mmand . ses sion module mod Syntax Description mod Target module for the command. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches session module You exit the virtual console with the exit or quit commands. When the inactivity perio d o f the terminal o n th e active su pervisor eng ine where y ou logged in exceeds the co nfigured id le time, you are automatically logg ed ou t of the terminal on the active superv isor engine. In such a case, the virtu al conso le session is also termin ated.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches set set To mark IP traffic by setting a class o f service (CoS), a Differentiated Services Cod e Point (DSCP), or IP-precedence in th e packet, use the set policy-map class configuration co mmand . To remove the traffic classification, u se the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches set Switch(config)# policy-map p1 Switch(config-pmap)# class voice Switch(config-pmap-c)# set cos 1 Switch(config-pmap)# exit Switch(config-pmap)# class video-data Switch(config-pmap-c)# set cos 2 Switch(config-pmap)# exit Switch# You can verify your settings by entering the show policy -map privileg ed EXEC command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches set cos set cos To set the Layer 2 class of service (CoS) valu e of a packet, use the set cos co mmand in p olicy-map class co nfiguration mode. To remove a sp ecific Co S value setting, use the no form o f this co mmand . set co s { cos-va lue | from-field [table ta ble-map -na me]} no set cos {cos-value | from-field [table table-map-name]} Syntax Description co s-value Specific IEEE 802.1Q CoS valu e from 0 to 7.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches set cos Note If you con figure the set cos dscp command, on ly the first th ree bits (the clas s selector bits) of the DSCP field are used. Note If you configure the set cos qos gro up command , only th e three least significant b its o f the q os grou p field are used. Examples This example s hows how to config ure a policy map called cos-set an d assig n d ifferent CoS values for d ifferent types of traffic.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches set dscp set dscp To mark a packet by setting the differen tiated services code point (DSCP) value in th e type of service (ToS) byte, use the set dscp comman d in policy-map class co nfiguration mo de. To remove a p rev iously set DSCP value, u se the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches set dscp • Preceden ce • Differen tiated services code point (DSCP) If you sp ecify a “fro m-field” catego ry but do not specify the table k eyword and the applicable ta ble-map -na me argu ment, the default action will be to cop y the value asso ciated with the “fro m-field” category as th e DSCP value. For instance, if yo u configure the set dscp cos comman d, the CoS value will b e copied and used as th e DSCP value.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches set dscp Related Commands Co mmand match (clas s-map co nfiguration) policy-map Description Defines the match criteria fo r a class map. service-policy (policy-map cla ss) Creates a serv ice policy that is a quality of serv ice (QoS) policy within a policy map. set co s Creates or modifies a policy map that can be attach ed to mu ltiple ports to sp ecify a service policy an d to enter policy-map co nfiguration mode.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches set precedence set precedence To set the precedence valu e in the pack et header, u se the set precedence command in p olicy-map class configuration mod e. To remove the precedence valu e, use the no form o f this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches set precedence If you specify a “from-field ” category bu t d o n ot specify th e table key word and the ap plicable table-map-name argument, the d efault action will be to copy the value associated with the “from-field ” categ ory as the precedence valu e. For instance, if you configu re the set precedence cos comman d, the CoS value will b e copied and us ed as th e preceden ce value.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches set precedence Command Descriptio n service-po licy (po licy-ma p class) set cos Creates a service po licy that is a q uality o f service (QoS) po licy within a po licy map . Sets IP traffic by s etting a class of serv ice (CoS). set dscp Marks a packet by settin g th e differentiated serv ices cod e p oint (DSCP) value in the type o f service (ToS) by te.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches set qos-group set qos-group To set a quality o f service (QoS) group identifier (ID) that can be used later to classify packets, use th e set qo s-group command in policy-map class configu ration mode. To remove the gro up ID, use the no form of this comman d. set qo s-group g rou p-id no set qos-group group-id Syntax Description Command Default group-id Group ID number in the range fro m 0 to 63. The gro up ID is set to 0.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches shape (class-based queueing) shape (class-based queueing) To en able traffic shaping a class o f traffic in a po licy map attached to a ph ysical port, use the shape average p olicy-map class command. Traffic shaping limits the data transmission rate. To return to the d efault setting, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches shape (class-based queueing) Switch(config-pmap-c)# shape average 256000 Switch(config-pmap-c)# exit Switch(config-pmap)# exit Switch(config)# interface gigabitethernet1/1 Switch(config-if)# service-policy output policy1 Switch(config-if)# end You can verify you r settin gs by entering the show policy-map privileged EXEC comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches shape (interface configuration) shape (interface configuration) To specify traffic shaping on an interface, use the shape comman d. To remove traffic shaping , use the no form of th is command shape [rate] [percent] no shape [rate] [percent] Syntax Description rate percent Defaults (Optio nal) Sp ecifies an av erag e rate for traffic shaping ; the range is 1 6000 to 1 00000 0000.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches shell trigger shell trigger Use the s hell trig ger global config uration co mmand to create a user defined trigger. Use th e no form of this co mmand to delete the trigger. shell trigger id entifier descriptio n no shell trigger identifier description Syntax Description identifier Specifies the event trigger identifier. The identifier s hould have no spaces or hyp hen s b etween words. Specifies the event trigger descriptio n text.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches shell trigger Related Commands Command Desc ription macro auto g lobal processing Enables Auto Smartports o n a switch. macro auto processing show shell Enable Auto SmartPo rts macros on a specific interface. Displays information about event trig gers an d macros. macro auto device Simp lifies changing the parameters for a bu ilt-in functions for a device ty pe.
22 Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show acc ess-group mode interface show access-group mode interface To disp lay the ACL con figuratio n o n a Layer 2 interface, use th e show access-group mo de interface co mmand . show access-group mode interface [interface interface-nu mber] Syntax Description interface interface-numb er (Option al) Interface ty pe; valid values are ethernet, fastethernet, gig abitethernet, tengig abitethernet, a nd port-channel.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show adjacency show adjacency To d isplay information about th e Layer 3 switching adjacency table, u se the show adjacency command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show adjacency Examples This examp le shows how to d isplay adjacency info rmation: Switch# show adjacency Protocol Interface IP FastEthernet2/3 IP FastEthernet2/3 Switch# Address 172.20.52.1(3045) 172.20.52.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ancp multicast show ancp multicast To display multicast streams activated by Access Nod e Control Protocol (ANCP), use the show ancp multicast command. show a ncp multicast [group groupa ddr] [source so urceaddr] | [ interface in terfacename] Syntax Description group g rou paddr so urce sourcead dr (Optional) Specifies a multicast gro up ad dress. (Optional) Specifies a multicast source ad dress.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show arp access-list show arp access-list To disp lay detailed information on an ARP access list, u se the s how arp co mmand . show arp access-list Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings. Command Modes Examples EXEC This examp le shows how to d isplay th e ARP ACL in formation for a switch: Switch# show arp access-list ARP access list rose permit ip 10.101.1.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show authentication show authentication To display the Auth Man ager in formatio n, use the show authentication command in EXEC o r Priv ileged EXEC mo de.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show authentication Table 2-10 Field Idle Running show authentication Command Output Description Th e session has been initialized an d no metho ds have run yet. A method is ru nning for this session. No methods No method h as provided a result for this session. Auth c Success A method has resulted in auth entication success fo r this sess ion. Auth c Failed A method has resulted in auth entication fail for th is session .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show authentication 3 0 dot1x Runnable methods list: Handle Priority Name 3 0 dot1x Switch# The following example shows how to display all Au th M anager sessions on the switch: Switch# show authentication sessions Interface MAC Address Method Domain Gi3/45 (unknown) N/A DATA Gi3/46 (unknown) N/A DATA Status Authz Failed Authz Success Session ID 0908140400000007003651EC 09081404000000080057C274 The following example shows how to disp
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show authentication IPv6 Address: IPv4 Address: User-Name: Status: Domain: Security Policy: Security Status: Oper host mode: Oper control dir: Session timeout: Common Session ID: Acct Session ID: Handle: Current Policy: Unknown Unknown gupn Authorized DATA Should Secure Unsecure multi-host both N/A 0D0102330000000D0003329A Unknown 0x6F000002 POLICY_Et0/0 Local Policies: Template: SVC_1 (priority 10) Idle timeout: 500 sec TAG: blue URL Re
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show authentication Command Descriptio n authentication periodic authentication port-control authentication priority Enab les reauthentication for th is po rt. Con figures the port-control value. Specifies the priority of auth entication metho ds on an interface. authentication timer Con figures the au then tication timer. a uthentication v iolation Specifies the action to be taken when a security vio lation exists o n a port.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show auto install status show auto install status To disp lay the statu s of an automatic installation, u se the show auto insta ll status comman d. show auto install status Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show auto qos show auto qos To display th e au tomatic quality o f service (auto-Qo S) configuration that is applied, u se the show auto qos user EXEC co mmand . show a uto qos [interface [interface-id]] [{begin | exclude | include} expression] Syntax Description Command Modes Usage Guidelines interfa ce interfa ce-id (Optio nal) Displays auto-QoS information for the specified in terface or for all interfaces.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show bootflash: show bootflash: To disp lay information about the bootflash : file system, us e the s how boo tflash: comman d. show bootfla sh: [all | chips | filesys] Syntax Description all chips (Option al) Displays all pos sible Flas h in formatio n. (Option al) Displays Flash chip information. filesys (Option al) Displays file sy stem information. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show bootflash: This example s hows how to display all bo otflash information: Switch> show bootflash: all -# - ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name 1 .. image 8C5A393A 237E3C 14 2063804 Aug 23 1999 16:18:45 c4-bootmz 2 .. image D86EE0AD 957CE8 9 7470636 Sep 20 1999 13:48:49 rp.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show bootvar show bootvar To disp lay BOOT en viro nmen t variable info rmation, use the show bo otva r comman d. show bootvar Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show cable-diagnostics tdr show cable-diagnostics tdr To d isplay the test res ults for the TDR cable d iagn ostics , use the show ca ble-dia gno stics tdr command. show cable-diagnostics tdr {interface {interface interface-number}} Note Syntax Description This command will be deprecated in future Cisco IOS releases; use the diagnostic start comman d in stead.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show cable-diagnostics tdr Table 2-12 Field Related Commands show cable-diagnostics tdr Command Output Fields Description Interface Interface tested . Speed Current line sp eed. Pair Cable Length Local pair name. Distance to the fault in meters (m). Chan nel Pair des ignatio n (A, B, C, o r D). Status Pair status dis play ed is one of the following: • Terminated —The link is u p.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show call-home show call-home To display the config ured CallHome information, use the sho w call-home command in p rivileg ed EXEC mo de. show call-ho me [alert-group | detail | mail-s erver | profile {all | n ame} | s tatistics] Syntax Description a lert-group detail mail-server (Optio nal) Displays the available alert group. (Optio nal) Displays the CallHo me co nfigu ration in detail.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show call-ho me Profile Name: CiscoTAC-1 Switch# Config ured CallHome Info rmation in Detail Switch# show call-home detail Current call home settings: call home feature : disable call home message's from address: switch@example.com call home message's reply-to address: support@example.com vrf for call-home messages: Not yet set up contact person's email address: technical@example.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show call-home Alert-group -----------------------diagnostic environment inventory Severity -----------minor warning normal Syslog-Pattern -----------------------.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show call-ho me Periodic configuration info message is scheduled every 1 day of the month at 09:27 Periodic inventory info message is scheduled every 1 day of the month at 09:12 Alert-group Severity ------------------------ -----------diagnostic minor environment warning inventory normal Syslog-Pattern -----------------------.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show call-home 0 0 0 0 0 0 Total Failed 0 Config 0 Diagnostic 0 Environment 0 Inventory 0 SysLog 0 Test 0 Request 0 Send-CLI 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Total Ratelimit -dropped 0 Config 0 Diagnostic 0 Environment 0 Inventory 0 SysLog 0 Test 0 Request 0 Send-CLI 0 Request Send-CLI 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Last call-home message sent time: n/a Related Commands Command call-ho me (global configura tion) cal
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show cdp neighbors show cdp neighbors To display detailed information about the neighbo ring dev ices th at are discovered throug h CDP, use th e show cdp neighbors command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show cdp neighbors Tab le 2-13 describes th e fields that are shown in th e ex ample. Table 2-13 show cdp neighbors Field Descriptions Field Defin ition Device ID Con figured ID (name), MAC address, or serial nu mb er of th e neighbor d evice. Local In trfce (Local Interface) The pro toco l that is u sed by the co nnectivity media.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show cdp neighbors Table 2 -14 describes the field s th at are sh own in the example. Table 2-14 show cdp neighbors detail Field Descriptions Field Defin ition Device ID Name of the neighbor device and either the MAC address o r the serial numb er o f this dev ice. Entry add ress(es) List o f network add resses o f neighbor devices. [netwo rk protocol] address Network address of the n eigh bor device.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show class-map show class-map To display class map in formatio n, use the show class-ma p comman d. show class-ma p class_na me Syntax Description class_ name Defaults This command has no default setting s. Command Modes Examples Name of the class map.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show class-map Switch(config-pmap-c)# police 1000000 9000 Switch(config-pmap-c)# exit Switch(config-pmap)# exit Switch(config)# interface fastEthernet 6/1 Switch(config-if)# service-policy input p1 Switch(config-if)# end Switch# write memory Switch# show policy-map interface FastEthernet6/1 class-map c1 match flow ip source-address ip destination-address ip protocol l4 source-port l4 destination-port ! policy-map p1 class c1 police 1000000
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show diagnostic content show diagnostic content To display test in formatio n abou t the test ID, test attributes, and supported coverage test levels for each test an d for all modules, u se the sho w dia gnostic co ntent command. show diagnos tic content module {all | n um} Syntax Description a ll n um Defaults This command has no default setting s. Command Modes EXEC Examples Disp lays all th e modules on the chassis.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show diagnostic content Testing Interval ID Test Name Attributes (day hh:mm:ss.ms) ==== ========================================== ============ ================= 1) linecard-online-diag --------------------> **D****I** not configured Switch# Related Commands Co mmand Description show dia gnostic result module Displays the module-based diagnostic test results.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show diagnostic result module show diagnostic result module To display the mod ule-based d iagn ostic test results, u se the sho w dia gnostic result mo dule command. show diagnos tic result module [slot-n um | all] [test [test-id | test-id -rang e | all]] [detail] Syntax Description slo t-nu m a ll test (Optio nal) Sp ecifies the slot on which diagno stics are displayed. (Optio nal) Displays the d iagn ostics for all slots.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show diagnostic result module Test results: (. = Pass, F = Fail, U = Untested) 1) linecard-online-diag --------------------> . module 6: Overall diagnostic result: PASS Diagnostic level at card bootup: minimal Test results: (. = Pass, F = Fail, U = Untested) 1) linecard-online-diag --------------------> .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show diagnostic result module 12: . 13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: . 24: . 25: . 26: . 27: . 28: . 29: . 30: . 31: . au: . Switch Subsystem Memory ... 1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: . 9: . 10: . 11: . 12: . 13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: . 24: . 25: . 26: . 27: . 28: . 29: . 30: . 31: . 32: . 33: . 34: . 35: . 36: . 37: . 38: . 39: . 40: . 41: . 42: . 43: . 44: .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show diagnostic result module 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Per hour in the last day: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Per day in the last 30 days: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Direct memory test failures per minute in the last hour: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show diagnostic result module test show diagnostic result module test To display the resu lts o f the b ootup pack et memo ry test, use the show diag nos tic res ult module test command. The o utput indicates whether the test passed, failed, or was not ru n. show diagnos tic result module [N | all] [test test-id] [deta il] Syntax Description N a ll (Op tional) Specifies the mod ule nu mber. (Op tional) Specifies all modu les.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show diagno stic result module te st Slot Ports Card Type Diag Status Diag Details ---- ----- -------------------------------------- ---------------- -----------6 48 10/100/1000BaseT (RJ45)V, Cisco/IEEE Passed None Detailed Status --------------. = Pass L = Loopback failure I = Ilc failure E = SEEPROM failure U = Unknown S = Stub failure P = Port failure G = GBIC integrity check failure Ports 1 . 2 . 3 . 4 . 5 . 6 . 7 . 8 . 9 .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show diagnostic result module test 2 show diagnostic result module test 2 To display the results of the boo tup packet memory test, use the sho w dia gno stic result module test 2 command. The o utput indicates whether the test passed, failed, or was not ru n. show diagnos tic result module N test 2 [detail] Syntax Description N detail Defaults Non-detailed results. Command Modes EXEC mode Specifies th e modu le number.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show diagnostic result module test 2 bad buffers: 0 (0.0%) good buffers: 65536 (100.0%) Bootup test results: No errors. Related Commands Co mmand diagnostic monitor action Description Directs the action of th e switch when it detects a pack et memory failure. show diagnostic result mo dule Displays the results from the on going packet memory test. test 3 Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show diagnostic result module test 3 show diagnostic result module test 3 To display the resu lts fro m th e ongo ing packet memory tes t, use th e show diagnostic result module test 3 co mmand . The outpu t ind icates wheth er the test p assed, failed , or was not run. show diagnos tic result module N test 3 [detail] Syntax Description N detail Defaults Non-detailed results. Command Modes EXEC mode M odule n umber.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show diagnostic result module test 3 Per minute in the last hour: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Per hour in the last day: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Per day in the last 30 days: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Direct memory test failures per minute in the last hour: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show dot1x show dot1x To display the 80 2.1X statis tics and operational status for the entire switch or for a specified interface, u se the s how dot1x command. show dot1x [interface interface-id] | [s tatistics [interfa ce interfa ce-id]] | [all] Syntax Description interfa ce interfa ce-id (Op tional) Disp lays the 802.1X status fo r the sp ecified port. statistics a ll (Op tional) Displays 80 2.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show dot1x Examples This examp le shows how to d isplay th e outpu t fro m the show dot1x command: Switch# show dot1x Sysauthcontrol = Disabled Dot1x Protocol Version = 2 Dot1x Oper Controlled Directions = Both Dot1x Admin Controlled Directions = Both Critical Recovery Delay = 500 Critical EAP = Enabled Switch# This examp le shows how to d isplay th e 802.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show dot1x Table 2-15 show dot1x interface Field Description Field Description PortStatus Status of th e port (authorized or u nau thorized). The statu s o f a po rt is displayed as au thorized if the dot1x port-control interface configu ration co mmand is set to a uto an d h as successfully completed authentication . Port Co ntrol Setting of the dot1x port-control interface config uration command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show dot1x Related Commands Co mmand dot1x critical Description Enables th e 802 .1X critical auth en tication on a po rt. dot1x critical eapol Enables s end ing EAPOL success packets when a po rt is critically authorized partway through an EAP ex chang e. dot1x critical recov ery delay Sets the time interval between port rein itializatio ns.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show environment show environment To display the enviro nmen t alarm, o peratio nal status, and current read ing for the chassis, use the show env ironment command. show env ironment [alarm] | [sta tus [chassis | fantray | powersupply | supervisor]] | [temperature] Syntax Description Defaults (Optional) Specifies the alarm status of the chassis. (Optional) Specifies the operational status information.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show environment Power supplies currently available : 1 Chassis Type : WS-C4507R+E Power consumed by backplane : 40 Watts Switch Bandwidth Utilization : 0% Supervisor Led Color : Green Module Module Module Module 1 Status Led Color 3 Status Led Color 4 Status Led Color 7 Status Led Color : Green : Orange : Green : Green PoE Led Color : Green PoE Led Color : Green Beacon Led Status : off Fantray : Good Fantray removal timeout : 30 Pow
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show environment Fantray : good Power consumed by Fantray : 50 Watts Switch# This example s hows how to display information about the p ower supp ly: Switch# show environment status powersupply Power Supply Model No Type Status ------ --------------- --------- ------PS1 WS-X4008 AC 400W good PS2 WS-X4008 AC 400W good PS3 none --Switch# Fan Sensor -----good good -- This example s hows how to display information about the s uperviso r e
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show errdisable detect show errdisable detect To disp lay the erro r disable detection status, use the show errdisable detect command. show errdis able detect Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show errdisable recovery show errdisable recovery To display erro r disable recovery timer information, use th e show errdisable recovery command. show errdisable recovery Syntax Description This command has no arguments or keywo rds. Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show etherchannel show etherchannel To disp lay Eth erChan nel information for a channel, u se the show etherchannel comman d. show etherchannel [chann el-group] {port-channel | brief | detail | s umma ry | port | load-ba lance | protoco l} Syntax Description cha nnel-group port-channel brief (Optional) Number of the ch ann el group; valid values are from 1 to 64. Displays port-channel info rmation.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show etherchannel Source XOR Destination mac address Switch# This example s hows how to display a su mmary of information for a sp ecific gro up: Switch# show etherchannel 1 brief Group state = L3 Ports: 2 Maxports = 8 port-channels: 1 Max port-channels = 1 Switch# This example s hows how to display detailed information for a sp ecific g rou p: Switch# show etherchannel 1 detail Group state = L3 Ports: 2 Maxports = 8 Port-channels: 1 M
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show etherchannel Logical slot/port GC Passive port list Port state = 10/1 Number of ports in agport = 0 = 0x00000000 HotStandBy port = null = Fa5/4 Fa5/5 = Port-channel L3-Ag Ag-Not-Inuse Ports in the Port-channel: Index Load Port ------------------Switch# This examp le shows how to d isplay a one-line summary per channel group : Switch# show etherchannel summary Flags: D - down P - bundled in port-channel I - stand-alone s - suspended
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show etherchannel Port state = EC-Enbld Down Not-in-Bndl Usr-Config Channel group = 1 Mode = Desirable Gcchange = 0 Port-channel = null GC = 0x00000000 Psudo-agport = Po1 Port indx = 0 Load = 0x00 Flags: S - Device is sending Slow hello. A - Device is in Auto mode. Timers: H - Hello timer is running. S - Switching timer is running. C - Device is in Consistent state. P - Device learns on physical port. Q - Quit timer is running.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show flowcontrol show flowcontrol To disp lay the per-in terface statu s and statistics related to flow contro l, use the show flowcontrol co mmand . show flowco ntro l [module slo t | interface in terface] Syntax Description module slo t interface interface Defaults This comman d has no default settings. Command Modes Privileg ed EXEC mode Usage Guidelines (Optional) Limits the display to in terfaces on a sp ecific mo dule.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show flowcontrol Gi1/4 Gi1/5 Gi1/6 Gi3/1 Gi3/2 Gi3/3 Gi3/4 Gi3/5 Gi3/6 Switch# off off off off off off off off off off off off off off off off off off desired desired desired desired desired desired desired desired desired on on on off off off off off off 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 This example s hows how to display the flow control s tatus on mod ule 1: Switch# show flowcontrol module 1 Port Send FlowControl Receive Flow
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show idprom show idprom To disp lay the IDPROMs for the chassis, s uperviso r en gine, modu le, power sup plies, fan trays, clock module, and multiplexer (mux ) buffer, use the show idprom command. show idprom {all | cha ssis | module [mod] | interfa ce int_name | supervisor | power-supply number | fan-tray } Syntax Description Defaults all chass is Display s in formatio n for all IDPROMs .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show idprom Linecard Block Version = 1 Linecard Block Length = 24 Linecard Block Checksum = 658 Feature Bits = 0x0000000000000000 Card Feature Index = 50 MAC Base = 0010.7bab.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show idprom 0x0020 52 20 20 20 00 00 90 65 46 54 52 2D 30 31 31 39 0x0030 2D 43 53 43 20 20 20 20 42 20 20 20 00 00 00 1A 0x0040 00 1A 00 00 4B 31 32 37 33 44 48 20 20 20 20 20 0x0050 20 20 20 20 30 33 30 34 30 39 20 20 64 00 00 B2 0x0060 29 00 02 80 22 33 38 3D C7 67 83 E8 DF 65 6A AF 0x0070 1A 80 ED 00 00 00 00 00 00 00 00 00 38 23 3C 1B Switch# R ..^PeFTR-0119 -CSC B .... ....K1273DH 030409 d..2 )..^@"38=Gg^C._ej. .^@m.........8#<.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show idprom 0x00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x30: 00 00 00 00 11 E2 69 A9 2F 95 C6 EE D2 DA B3 FD 0x40: 9A 34 4A 24 CB 00 00 00 00 00 00 00 00 00 EF FC 0x50: F4 AC 1A D7 11 08 01 36 00 Switch# This example s hows how to display IDPROM in formatio n for th e supervisor engine: Switch# show idprom supervisor Su
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show idprom Chassis Block Signature = 0x4001 Chassis Block Version = 1 Chassis Block Length = 22 Chassis Block Checksum = 421 Feature Bits = 0x0000000000000000 MAC Base = 0004.dd42.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show idprom Snmp OID = 65535.65535.65535.65535.65535.65535.65535.65535 Power Consumption = -1 RMA Failure Code = 255 255 255 255 Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show interfaces show interfaces To disp lay traffic on a specific interface, use th e show interfaces command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show interfaces Keepalive set (10 sec) Full-duplex, 1000Mb/s ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output never, output hang never Last clearing of "show interface" counters never Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 1000 bits/sec, 2 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec L2 Switched: ucast: 8199 pkt, 1362060 bytes - mcast: 6980 pkt, 3719
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show interfaces FastEthernet6/3 is up, line protocol is up (connected) Hardware is Fast Ethernet Port, address is 0003.6ba8.ee68 (bia 0003.6ba8.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show interfaces capabilities show interfaces capabilities To display the interface capabilities for an interface or for all the interfaces on a switch, use th e show interfa ces ca pa bilities command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show interfaces capabilities Link Debounce Time: no Port Security yes Dot1x yes GigabitEthernet1/2 Model: WS-X4516-Gbic Type: Unsupported GBIC Speed: 1000 Duplex: full Trunk encap. type: 802.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show interfaces capabilities Duplex: full Trunk encap. type: 802.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show interfaces capabilities Fast Start: yes Queuing: rx-(N/A), tx-(1p3q1t, Sharing/Shaping) CoS rewrite: yes ToS rewrite: yes Inline power: no SPAN: source/destination UDLD: yes Link Debounce: no Link Debounce Time: no Port Security: yes Dot1x: yes Maximum MTU: 1552 bytes (Baby Giants) Multiple Media Types: no Diagnostic Monitoring: N/A Switch# Related Commands Co mmand show interfaces counters Description Displays the traffic on the p
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show interfaces counters show interfaces counters To display the traffic on th e phys ical in terface, use the show interfaces counters comman d. show interfa ces co unters [all | detail | erro rs | storm-control | trunk] [module mod ] Syntax Description a ll (Optional) Displays all the interface cou nters including erro rs, trunk, and detail. detail errors Defaults (Optional) Dis play s th e detailed interface counters.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show interfaces counters Switch# show interfaces counters trunk module 1 Port Gi1/1 Gi1/2 Switch# TrunkFramesTx 0 0 TrunkFramesRx 0 0 WrongEncap 0 0 This examp le shows how to d isplay th e number o f packets that are discarded d ue to sup pression: Switch# show interfaces counters storm-control Multicast Suppression : Enabled Port Fa5/35 Switch# Related Commands BcastSuppLevel 10.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show interfaces description show interfaces description To display a description and status of an interface, use th e show interfaces description comman d. show interfa ces [interface] description Syntax Description in terface Defaults This command has no default setting s. Command Modes Examples (Optio nal) Typ e of in terface.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show interfaces link show interfaces link To disp lay how lo ng a cable has b een disconnected from an in terface, use the show interfaces link co mmand : show interfaces link [module mod_n um] Syntax Description module mod_n um Defaults This comman d has no default settings. (Optional) Limits the display to in terfaces on a mod ule.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show interfaces mtu show interfaces mtu To display the maximum transmissio n unit (MTU) size of all the p hysical interfaces and SVIs on the switch , use the show interfaces mtu comman d. show interfa ces mtu [module mod] Syntax Description module mo d Defaults This command has no default setting s. (Optio nal) Limits the disp lay to interfaces o n a specific modu le.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show interfaces private-vlan mapping show interfaces private-vlan mapping To disp lay PVLAN mapping information for VLAN SVIs, use the show interfaces priv ate-v lan mapping command. show interfaces priv ate-v lan mapping [active] Syntax Description active Defaults This comman d has no default settings. Command Modes Usage Guidelines Examples (Optio nal) Displays active interfaces only.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show interfaces status show interfaces status To display the interface status or a list of interfaces in error-disabled state, use the show interfaces status command. show interfa ces sta tus [err-disabled | inactive ] [module {modu le}] Syntax Description err-disabled inactive (Option al) Displays interfaces in error-disabled state. (Option al) Displays interfaces in inactive state.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show interfaces status This examp le shows how to d isplay th e Gigabit Ethernet interfaces on a WS-X46 06-10GE-E switch using the TwinGig Convertor: Switch# show interfaces status module 1 Port Name Status Vlan Duplex Speed Type Te1/1 inactive 1 full 10G No X2 Te1/2 inactive 1 full 10G No X2 Te1/3 inactive 1 full 10G No X2 Te1/4 notconnect 1 full 10G No X2 Te1/5 notconnect 1 full 10G No X2 Te1/6 notconnect 1 full 10G No X2 Gi1/7 notconnec
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show interfaces switchport show interfaces switchport To display the administrativ e and operational status of a switching (nonroutin g) port, us e the show interfa ces switchport comman d. show interfa ces [interface-id] switchport [module mod] Syntax Description in terface-id module mo d (Optio nal) Interface ID for the physical po rt.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show interfaces switchport Trunking VLANs Enabled:ALL Pruning VLANs Enabled:2-1001 Switch# This examp le shows how to d isplay th e status of native VLAN tagging on the port: Switch# show interfaces f3/1 switchport show interface f3/1 switchport Name: Fa3/1 Switchport: Enabled Administrative Mode: private-vlan promiscuous Operational Mode: private-vlan trunk secondary Administrative Trunking Encapsulation: negotiate Operational Trunking E
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show interfaces transceiver show interfaces transceiver To display diagnostic-mo nitorin g d ata for all interfaces that have transceivers ins talled, u se the s how interfa ces transceiver command. show interfa ces {{[int_ name] tra nsceiver {[detail ]} | {transceiver [module mo d] | detail [module mod]}} Syntax Description in t_name detail module mo d Defaults (Optional) Interface name.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show interfaces transceiver Note The valu e fo r the Op tical Tx Power (in d Bm) equ als ten times lo g (Tx Power in mW). If th e Tx Power value is 3 mW, then the Optical Tx Power value equals 10 * lo g (3), which equals 10 * .477 or 4.77 dBm. Th e Op tical Rx Power value behaves similarly. If the Tx Power or the Rx Power is zero, th en its dBm value is u ndefined an d is shown as N/A (no t applicable).
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show interfaces transceiver This examp le sh ows how to display th e mon itoring data for the interfaces th at h ave transceivers installed o n mo dule 2 : Switch# show interfaces transceiver module 2 If device is externally calibrated, only calibrated values are printed. ++ : high alarm, + : high warning, - : low warning, -- : low alarm. NA or N/A: not applicable, Tx: transmit, Rx: receive. mA: milliamperes, dBm: decibels (milliwatts).
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show interfaces transceiver This examp le shows how to d isplay th e monitoring data for the transceivers on interface Gi1/2: Switch# show interfaces g1/2 transceiver ITU Channel 23 (1558.98 nm), Transceiver is externally calibrated. If device is externally calibrated, only calibrated values are printed. ++ : high alarm, + : high warning, - : low warning, -- : low alarm. NA or N/A: not applicable, Tx: transmit, Rx: receive.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show interfaces transceiver Related Commands Command show idprom Descriptio n Displays the IDPROMs for the ch ass is . show interfa ces sta tus Displays the interface s tatus or a list of interfaces in error-disabled state. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show in terfaces trunk show interfaces trunk To disp lay po rt an d mo dule in terface-trun k in formatio n, use the show interfa ces trunk co mmand . show interfaces trunk [mo dule mod] Syntax Description module mod Defaults This comman d has no default settings. (Optional) Limits th e disp lay to interfaces on the specified mo dule; valid values are from 1 to 6 .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show interfaces trunk Port Vlans allowed and active in management domain Fa5/1 none Fa5/2 none Fa5/3 none Fa5/4 none Fa5/5 none Fa5/6 none Fa5/7 none Fa5/8 200 Fa5/9 1-6,10,20,50,100,152,200,300,303-305,349-351,400,500,521,524,570,801-8 02,850,917,999,1002-1005 Fa5/10 none Fa5/11 none Fa5/12 none Fa5/48 none Port Vlans in spanning tree forwarding state and not pruned Fa5/1 none Fa5/2 none Fa5/3 none Fa5/4 none Fa5/5 none Fa5/6 none Fa
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ip arp inspection show ip arp inspection To show th e status of dyn amic ARP in spection for a s pecific range of VLANs , use the show ip arp ins pection co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip arp inspection 4 100 101 1006 1007 0 0 0 0 0 0 0 0 0 0 Vlan ---1 2 3 4 100 101 1006 1007 DHCP Permits -----------0 0 68322 0 0 0 0 0 ACL Permits ----------0 0 0 0 0 0 0 0 Vlan Dest MAC Failures -------------------1 0 2 0 3 0 4 0 100 0 101 0 1006 0 1007 0 Switch# 0 0 0 0 0 0 0 0 0 0 Source MAC Failures ------------------0 0 0 0 0 0 0 0 IP Validation Failures ---------------------0 0 0 0 0 0 0 0 This example s hows how t
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ip arp inspection Fa3/6 Fa3/7 Switch# Related Commands Untrusted Untrusted 15 15 Co mmand arp access-list Description Defines an ARP access list or add s clauses at the end of a predefined list. clear ip arp inspection log show ip arp inspection lo g Clears the status of the log buffer. Displays the status of the log buffer. Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip arp inspection log show ip arp inspection log To show the status of the log buffer, u se the sho w ip arp inspection log command. show ip arp inspectio n log Syntax Description This command has no arguments or keywo rds. Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ip cef vlan show ip cef vlan To view IP CEF VLAN interface status an d configuratio n in formatio n and disp lay the prefixes fo r a specific interface, use the show ip cef vlan comman d. show ip cef vlan vlan _num [detail] Syntax Description vla n_num detail Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip dhcp snooping show ip dhcp snooping To display the DHCP sn ooping configuration , use the show ip dhcp snooping co mmand . show ip dhcp s noo ping Syntax Description This command has no arguments or keywo rds. Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ip dhcp snoop ing binding show ip dhcp snooping binding To disp lay the DHCP snoop ing binding entries, use th e show ip dhcp snooping binding command. show ip dhcp snooping binding [ip-address] [mac-ad dress] [vlan vlan_nu m] [interfa ce in terfa ce_num] Syntax Description Defaults ip-a ddress mac-addres s (Optio nal) IP add ress for the bind ing en tries. (Optio nal) MAC addres s for the bindin g entries.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip dhcp snooping binding This example s hows how to display the DHCP snoop in g binding entries’ M AC address for a specific VLAN: Switch# show ip dhcp snooping binding 55.5.5.2 0002.b33f.3d5f vlan 99 MacAddress -----------------00:02:B3:3F:3D:5F Switch# IpAddress --------------55.5.5.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ip dhcp snoop ing binding Co mmand Description ip igmp snoo ping ip igmp snoo ping vlan Enables IGM P snooping. Enables IGM P snooping for a VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip dhcp snooping database show ip dhcp snooping database To display the status of th e DHCP snoo ping datab ase agent, use the show ip dhcp snooping da tabase command. show ip dhcp s noo ping database [detail] Syntax Description detail Defaults This command has no default setting s. (Optio nal) Provides ad ditional o perating state and statistics in formation.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ip dh cp snooping database Successful Writes Media Failures : : 0 0 Failed Writes : 21 First successful access: Read Last ignored bindings counters : Binding Collisions : 0 Invalid interfaces : 0 Parse failures : 0 Last Ignored Time : None Total ignored bindings counters: Binding Collisions : 0 Invalid interfaces : 0 Parse failures : 0 Expired leases : Unsupported vlans : 0 0 Expired leases : Unsupported vlans : 0 0 Switch#
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip igmp interface show ip igmp interface To view IP IGMP interface status and con figuration info rmation, u se the show ip igmp interface command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ip igmp profile show ip igmp profile To view all config ured IGMP p rofiles or a specified IGMP pro file, use th e show ip ig mp profile privileged EXEC command. show ip igmp profile [profile number] Syntax Description profile number Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip igmp snooping show ip igmp snooping To display info rmation on dyn amically learned an d manually configu red VLAN switch interfaces, use th e show ip ig mp sno oping command. show ip igmp snooping [querier | gro ups | mrouter] [v lan vlan_id ] a.b.c.d [summary | sources | h osts] [cou nt] Syntax Description querier groups v lan vlan_id (Optional) Specifies that th e display will contain IP address and versio n in formatio n.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ip igmp snooping Explicit host tracking : Enabled Multicast router learning mode : pim-dvmrp CGMP interoperability mode : IGMP_ONLY Vlan 2: -------IGMP snooping : Enabled IGMPv2 immediate leave : Disabled Explicit host tracking : Enabled Multicast router learning mode : pim-dvmrp CGMP interoperability mode : IGMP_ONLY Switch> This examp le shows how to d isplay th e snoo ping information on VLAN 2: Switch# show ip igmp snooping vlan
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip igmp snooping Vlan Group Version Ports --------------------------------------------------------2 224.0.1.40 v3 Router 2 224.2.2.2 v3 Fa6/2 Switch> This example s hows how to display the g rou p’s host types and po rts in VLAN 1: Switch# show ip igmp snooping group vlan 1 Vlan Group Host Type Ports --------------------------------------------------------1 229.2.3.4 v3 fa2/1 fa2/3 1 224.2.2.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ip igmp snooping 1 Switch# Gi1/1,Gi2/1,Fa3/48,Router This example sh ows how to d is play the to tal number of group ad dresses learned by th e system glo bally : Switch# show ip igmp snooping group count Total number of groups: 54 Switch> This examp le shows how to d isplay th e total n umber of group addres ses learned on VLAN 5: Switch# show ip igmp snooping group vlan 5 count Total number of groups: 30 Switch> Related Commands
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip igmp snooping membership show ip igmp snooping membership To display host memb ership information, use th e show ip ig mp sno oping membership command. show ip igmp snooping membership [interface in terface_num] [v lan vlan_ id] [reporter a.b.c.d] [source a.b.c.d gro up a.b.c.d] Syntax Description interfa ce interfa ce_nu m v lan vlan_id reporter a.b.c.d (Optio nal) Displays IP address and version information of an interface.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ip igmp snooping membership Source/Group Interface Reporter Uptime Last-Join/ Last-Leave ------------------------------------------------------------------------------------------------------40.0.0.1/224.1.1.1 Fa7/37 0002.4ba0.a4f6 40.0.0.2/224.1.1.1 Fa7/37 0002.fd80.f770 00:00:04 00:00:04 / 00:00:17 00:00:17 / - 40.0.0.3/224.1.1.1 Fa7/36 20.20.20.20 00:00:04 00:00:04 / - 40.0.0.4/224.1.1.1 Fa7/35 20.20.20.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip igmp snooping mrouter show ip igmp snooping mrouter To disp lay info rmation on the dynamically learned and manu ally con figured multicast switch interfaces , u se the s how ip igmp snooping mrouter command. show ip igmp snooping mrouter [vlan vlan-id] Syntax Description v lan vlan-id Defaults This command has no default setting s. (Optio nal) Specifies a VLAN; valid valu es are from 1 to 1 001 an d fro m 100 6 to 409 4.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ip igmp snooping vlan show ip igmp snooping vlan To disp lay information on the dynamically learned and manually configu red VLAN switch interfaces, use th e show ip ig mp sno oping vla n comman d. show ip igmp snoo ping vlan vla n_num Syntax Description vla n_num Defaults This comman d has no default settings. Numb er o f the VLAN; valid values are from 1 to 1 001 and from 1006 to 4094 .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip interface show ip interface To display the us ability status of interfaces that are co nfigured for IP, use the show ip interface command. show ip interface [typ e number ] Syntax Description type n umber Defaults This command has no default setting s. Command Modes EXEC Usage Guidelines The Cisco IOS software auto matically enters a d irectly conn ected route in th e ro uting table if the in terface is u sab le.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches sho w ip interface IP fast switching is enabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is enabled IP Fast switching turbo vector IP Normal CEF switching turbo vector IP multicast fast switching is enabled IP multicast distributed fast switching is disabled IP route-cache flags are Fast, CEF Router Discovery is disabled IP output packet accounting is disabled IP access violation ac
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip interface Table 2-19 show ip interface Field Descriptions (continued) Field ICMP red irects ICMP un reachables Descriptio n Status of the redirect messages on this interface. Status of the unreachab le mes sages on this interface. ICMP mask replies Status of the mask rep lies on this interface. IP fast switchin g Status of wheth er fast switch ing has been enabled fo r this in terface.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ip mfib show ip mfib To disp lay all active Multicast Forwarding Info rmation Base (MFIB) rou tes, use the show ip mfib co mmand . show ip mfib [all | co unters | log [n ]] Syntax Description all (Option al) Specifies all rou tes in the M FIB, including tho se routes th at are u sed to accelerate fast switching bu t that are not necess arily in th e u pper-layer rou tin g protocol table.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip mfib • Examples Not Platform (NP) fast-switched —Used with the F flag. A fo rwarding interface is also marked as Not Platfo rm fast-s witched when ever that o utput interface cann ot b e fast-switched by the platform hardware and requires software forwarding.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ip mfib fastdrop show ip mfib fastdrop To disp lay all currently active fast-drop entries and to show wheth er fast drop is en abled, use the show ip mfib fastdrop command. show ip mfib fastdrop Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip mroute show ip mroute To display IP multicast ro uting tab le information, use th e show ip mroute command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ip mroute J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running A - Advertised via MSDP, U - URD, I - Received Source Specific Host Report Outgoing interface flags:H - Hardware switched Timers:Uptime/Expires Interface state:Interface, Next-Hop or VCD, State/Mode (*, 230.13.13.1), 00:16:41/00:00:00, RP 10.15.1.20, flags:SJC Incoming interface:GigabitEthernet4/8, RPF nbr 10.15.1.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip mroute This example s hows how to display summary information : Switch# show ip mroute summary IP Multicast Routing Table Flags: D - Dense, S - Sparse, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running A - Advertised via MSDP, U - URD, I - Received Source Specific Host Report Outgoing interface flags: H - Hard
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ip mroute Table 2-20 show ip mroute Field Descriptions (continued) Field Description J - Join SPT Fo r (*, G) entries , ind icates that th e rate of traffic flowing down the shared tree is ex ceeding the SPT-Th reshold set fo r the gro up. (The default SPT-Threshold setting is 0 k bps.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip mroute Table 2-20 show ip mroute Field Descriptions (continued) Field Descriptio n RP Address of the RP s witch. For switches and access servers o perating in s parse mo de, this ad dress is always 0.0.0.0. flags: Information about the entry. Incoming interface Expected interface for a mu lticast packet from th e source. If th e p acket is not received on this interface, it is d iscard ed.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ip source binding show ip source binding To display IP sou rce binding s that are configured on th e system, use the show ip source binding EXEC co mmand . show ip source binding [ip-address] [mac-a ddres s] [dhcp-snooping | static] [vlan vla n-id ] [interfa ce in terfa ce-n ame] Syntax Description ip-a ddress mac-addres s (Optional) Bindin g IP add ress. (Optional) Bindin g MAC address .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip verify source show ip verify source To d isplay the IP sou rce guard config uration and filters on a particular interface, u se the show ip verify so urce co mmand . show ip verify source [interface interface_n um] Syntax Description interfa ce interfa ce_nu m Defaults This command has no default setting s. (Optio nal) Sp ecifies an interface.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ip verify source fa6/4 fa6/4 • ip-mac ip-mac • active active 11.0.0.1 deny-all aaaa.bbbb.cccd deny-all 11 12-20 This outp ut appears wh en yo u enter the show ip verify source interface fa6 /5 command and the interface fa6/5 h as IP sou rce filter mo de that is config ured as IP MAC and existing IP MAC binding 10.0.0.3/aaaa.bbb b.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip wccp show ip wccp To d is play the Web Cache Communication Protocol (WCCP) g lobal configu ration and statistics, use the show ip wccp comman d in u ser EXEC or privileged EXEC mode.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ip wccp • show ip wccp service-numb er detail • show ip wccp interfa ces • show ip wccp web-cache • show ip wccp web-cache detail • show ip wccp show ip w ccp service-n umber The following is s ample output from the show ip wccp service-n umber command : Switch# show ip wccp 90 Global WCCP information: Router information: Router Identifier: Protocol Version: 100.1.1.16 2.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip wccp Table 21 show ip wccp ser vice-number Field Descriptions (continued) Field Description Grou p Access-list Indicates wh ich cach e engin e is allowed to con nect to th e router. Total Messages Denied to Group Indicates the n umber of packets denied b y the grou p-list access list. Total Authentication failures The number of instances where a password did no t match.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ip wccp State: Redirection: Packet Return: Packets Redirected: Connect Time: Assignment: Usable L2 GRE 0 00:05:23 MASK Mask SrcAddr DstAddr SrcPort DstPort ---- ------------------- ------0000: 0x00000000 0x00000001 0x0000 0x0000 Value SrcAddr DstAddr SrcPort DstPort CE-IP ----- ------------------- ------- ----0000: 0x00000000 0x00000000 0x0000 0x0000 0x0A0A0A02 (10.10.10.2) 0001: 0x00000000 0x00000001 0x0000 0x0000 0x0A0A0A02 (10.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip wccp Platform: Redirect access-list: Total Packets Denied Redirect: Total Packets Unassigned: Group access-list: Total Messages Denied to Group: Total Authentication failures: Total Bypassed Packets Received: 0 0 no_linux 0 0 -none0 0 Tab le 24 describes the sig nifican t fields shown in th e display. Table 24 show ip wccp web-cache Field Descriptions Field Description Protocol Version Ind icates th at WCCPv2 is en abled.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ip wccp ----- ------------------- ------- ----0000: 0x00000000 0x00000000 0x0000 0x0000 0x0A0A0A02 (10.10.10.2) 0001: 0x00000000 0x00000001 0x0000 0x0000 0x0A0A0A02 (10.10.10.2) Table 2 5 d escribes the significant fields s hown in the d isplay. Table 25 show ip wccp web-cache detail Field Descriptions Field Description WCCP Client In formatio n Th e head er for th e area that con tains fields for information on clien ts.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ip wccp Total Bypassed Packets Received: Related Commands Command clear ip wccp ip wccp ip wccp redirect 0 Description Clears the co unter for packets redirected u sing WCCP. Enables s upport of the WCCP service for participatio n in a service gro up. Enables p acket redirectio n on an ou tbound or inboun d interface using WCCP. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ipc show ipc To disp lay IPC information, use th e show ipc comman d. show ipc {nodes | ports | queue | sta tus} Syntax Description nodes ports queue Displays the particip ating n odes. Displays the local IPC ports . Displays the con tents of the IPC retrans mis sion queue. sta tus Displays the status of the local IPC server. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ipc This example s hows how to display the con tents of th e IPC retransmis sion queue: Switch# show ipc queue There are 0 IPC messages waiting for acknowledgement in the transmit queue. There are 0 IPC messages waiting for a response. There are 0 IPC messages waiting for additional fragments. There are 0 IPC messages currently on the IPC inboundQ. There are 0 messages currently in use by the system.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ipv6 snooping counters show ipv6 snooping counters To disp lay the number of p ackets d rop ped p er p ort due to RA Guard , use the show ipv6 snooping co unters inter face co mmand . show ipv6 sno oping counters interface Syntax Description interface Defaults Non e Command Modes Examples Specifies the interface.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ipv6 mld snooping show ipv6 mld snooping To display IP version 6 (IPv6 ) Multicas t Listener Discovery (MLD) sno oping configuration of the switch o r the VLAN, us e the show ipv6 mld snooping co mmand . show ipv6 mld snooping [v lan vlan-id] Syntax Description v lan vlan-id Command Modes User EXEC mode Usage Guidelines (Optio nal) Sp ecifies a VLAN; the range is 1 to 10 01 and 1 006 to 4094.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ipv6 mld snooping Last listener query count Last listener query interval Vlan 1: -------MLD snooping MLDv1 immediate leave Explicit host tracking Multicast router learning mode Robustness variable Last listener query count Last listener query interval : 2 : 1000 : Disabled : Disabled : Enabled : pim-dvmrp : 1 : 2 : 1000
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ipv6 mld snooping mrouter show ipv6 mld snooping mrouter To display dynamically learned and manually co nfigu red IP version 6 (IPv6) Mu lticast Listen er Discovery (MLD) switch ports for the switch or a VLAN, use the show ipv6 mld snooping mrouter command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ipv6 mld snooping querier show ipv6 mld snooping querier To disp lay IP versio n 6 (IPv6 ) Multicast Listener Discovery (MLD) snoo ping querier-related info rmation most recently received by the s witch o r the VLAN, u se the s how ipv6 mld snoo ping querier command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show ipv6 mld snooping querier Command Descriptio n ipv6 mld snooping Enab les IP versio n 6 (IPv6 ) Multicast Listener Dis covery (MLD) snoo ping globally or o n th e specified VLAN. ipv6 mld snooping Con figures IP vers ion 6 (IPv 6) Multicas t Lis tener last-listener-query-count Disco very Mulitcast Add ress Sp ecific Queries (MASQs) th at will be s ent befo re aging o ut a client.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show issu capability show issu capability To disp lay the ISSU capability fo r a clien t, use the show issu ca pa bility co mmand . show issu capability { entries | groups | types } [client_id ] Syntax Description entries Displays a list of Capability Types and Dependent Capability Types th at are included in a single Capability Entry. Typ es with in an entry can also be independent.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show issu capability Cap_Entry = 1 Cap_Type = 0 Switch# Related Commands Command show iss u clients Descriptio n Displays the ISSU clients. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches sho w issu clien ts show issu clients To disp lay the ISSU clients, use the show issu clients co mmand . show issu clients [peer_uid ] Syntax Description peer_ uid Defaults Displays a list of clients registered to the ISSU infrastructu re at the su pervisor en gine where th e co mmand is entered. Command Modes User EXEC mode (Optional) Dis play s a list o f clients registered to ISSU infrastru cture at the peer s uperviso r en gine.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show issu clients Client_ID = 2071, Client_ID = 2072, Client_ID = 2073, Client_ID = 2077, Client_ID = 2078, Client_ID = 2079, Client_ID = 2081, Client_ID = 2082, Client_ID = 2083, Client_ID = 2084, Client_ID = 4001, Client_ID = 4002, Client_ID = 4003, Client_ID = 4004, Client_ID = 4005, Base Clients: Client_Name = Client_Name = Client_Name = Client_Name = Client_Name = Client_Name = Client_Name = Client_Name = Client_Name = Client_Name =
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show issu comp-matrix show issu comp-matrix To display in formatio n regarding the In Service So ftware Upgrade (ISSU) comp atibility matrix, us e the show issu comp-matrix co mmand . show issu comp-matrix {nego tiated | sto red | xml} Syntax Description nego tiated Displays negotiated compatibility matrix information. sto red xml Displays stored compatibility matrix information.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show issu comp-matrix Examples This example d isplays n ego tiated co mp atibility matrix information : Switch# show issu comp-matrix negotiated CardType: WS-C4507R(112), Uid: 2, Image Ver: 12.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show issu comp-matrix 5 7 8 9 10 11 100 110 200 2002 2003 2004 2008 2008 2010 2012 2021 2022 2023 2024 2025 2026 2027 2028 2054 2058 2059 2067 2068 2070 2071 2072 2073 2077 2078 2079 2081 2082 2083 2084 4001 4002 4003 4004 4005 1 1 1 1 1 1 1 113 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 101 201 301 401 1 1 1 1 1 1 1 1 115 1 2 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 262186 262156 262148
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show issu comp-matrix 2008 2010 2012 2021 2022 2023 2024 2025 2026 2027 2028 2054 2058 2059 2067 2068 2070 2071 2072 2073 2077 2078 2079 2081 2082 2083 2084 4001 4002 4003 4004 4005 ISSU Tableid Client Base ARP HA Base ISSU HSRP Client Non-Base XDR Int Priority ISSU cliBase XDR Proc Priority ISSU clBase FIB HWIDB ISSU client Base FIB IDB ISSU client Base FIB HW subblock ISSU clieBase FIB SW subblock ISSU clieBase Adjacency ISSU client B
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show issu endpoin ts show issu endpoints To disp lay the ISSU en dpoint information, use th e show issu endpoints co mmand . show issu endpo ints Syntax Description This comman d has no argu ments or keyword s Defaults This comman d has no default settings. Command Modes Usage Guidelines Examples User EXEC mode Endp oint is an ex ecution unit with in a redun dan cy domain.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show issu entities show issu entities To display the ISSU entity information, use th e show issu entities command. show iss u entities [client_id] Syntax Description client_id Defaults This command has no default setting s. (Optio nal) ISSU client ID. Command Modes User EXEC mode Usage Guidelines Entity is a logical g rou p of sess ions with some commo n attributes (like cap ability list an d mess age type).
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show issu fsm show issu fsm Note This comman d is no t in tend ed for end-users. To disp lay the ISSU finite state mach ine (FSM) in formatio n correspon ding to an ISSU session, use the show issu fsm command. show issu fsm [session_id] Syntax Description ses sion_id Defaults This comman d has no default settings. (Optional) Prov ides detailed information about the FSM fo r the s pecified ses sion.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show issu message show issu message To display ch eckpoin t messages for a specified ISSU clien t, use the show issu message co mmand . show iss u messa ge {groups | types } [client_id] Syntax Description groups types Displays information on Message Grou p supported by th e specified clien t. Displays information on all Message Types supp orted by the sp ecified client. client_id (Optional) Specifies a client ID.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show issu negotiated show issu negotiated To disp lay the neg otiated capability and message version information of th e ISSU clien ts, use the show issu negotiated command. show issu negotiated {capability | version} [session_id] Syntax Description ca pa bility version Displays all n egotiated capabilities. Displays details of all negotiated messages.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show issu rollback-timer show issu rollback-timer To display ISSU ro llback-timer status , use the show issu rollback-timer command. show iss u ro llba ck-timer Syntax Description This command has no arguments or keywo rds. Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show issu sessions show issu sessions To disp lay ISSU session information for a specified client, use th e show issu sess io ns command. show issu s essions [client_id ] Syntax Description client_id Defaults Displays session information for all clients registered to th e ISSU infrastru ctu re. Command Modes Usage Guidelines (Optional) Specifies the ISSU client ID.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show issu state show issu state To display the ISSU state and current booted image name during the ISSU process, u se the show iss u state co mmand . show iss u state [slot_ numb er ] [detail] Syntax Description slo t_number (Optio nal) Specifies th e slo t number whose ISSU state needs to be disp layed (1 or 2). (Optio nal) Provides detailed info rmation ab out the state of the active and standby su pervisor en gines.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show issu state Related Commands Co mmand issu a bo rtversion Description Cancels th e ISSU up grade o r the d owngrade process in pro gress an d res tores the switch to its state before the start of the pro cess. issu a cceptversion Halts the ro llb ack timer and ensu res that the new Cisco IOS software image is no t automatically stopp ed du ring the ISSU process.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show l2protocol-tunnel show l2protocol-tunnel To display info rmation ab out the Layer 2 protocol tunnel ports, use the show l2proto col-tunnel command. This co mmand d isplay s in formatio n for th e interfaces with pro toco l tun nelin g enabled.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show l2protocol-tunnel Fa0/11 Fa0/12 Fa0/13 udld cdp stp vtp pagp lacp udld cdp stp vtp pagp lacp udld cdp stp vtp pagp lacp udld ---1100 1100 1100 ---------------------------------------------- ------------900 900 900 ------------------------------------- 219 2356 116 3 856 0 0 2356 11787 81 0 849 0 2356 11788 81 0 849 0 211 2350 13 67 5848 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Switch# This is an exam
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show lacp show lacp To display LACP in formatio n, use the show la cp command. show la cp [channel-gro up] { counters | internal | neighbors | sys-id} Syntax Description chann el-group counters interna l Defaults (Optio nal) Number o f the channel g rou p; valid valu es are from 1 to 64 . Displays the LACP statis tical in formatio n. Displays the intern al information. neighbors Displays the neighb or information.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show lacp Port Fa4/1 Fa4/2 Fa4/3 Fa4/4 Switch# Flags saC saC saC saC State bndl bndl bndl bndl Interval 30s 30s 30s 30s Priority 32768 32768 32768 32768 Key 100 100 100 100 Key 100 100 100 100 Number 0xc1 0xc2 0xc3 0xc4 State 0x75 0x75 0x75 0x75 Table 2 -26 lists the output field definitions .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show lacp Port Fa4/1 Fa4/2 Fa4/3 Fa4/4 Fa4/1 Fa4/2 Fa4/3 Fa4/4 Switch# System ID 8000,00b0.c23e.d84e 8000,00b0.c23e.d84e 8000,00b0.c23e.d84e 8000,00b0.c23e.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show mab show mab To disp lay MAC au then tication bypass (MAB) information, use th e show ma b command in EXEC mode. show ma b {interface interface interface-number | a ll} [detail] Syntax Description interface interface interface-numb er Interface type; p ossible valid valu e is gigabitethernet. Module an d p ort numb er. all Displays MAB information for all in terfaces. detail (Optional) Dis play s d etailed MAB in formatio n.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show mab Tab le 2-29 lis ts th e possib le displayed values fo r the MAB autho rizatio n s tatus. Table 2-29 Examples MAB Authorization Status Values Status Description AUTHORIZED The session h as successfully authorized. UNAUTHORIZED The session h as failed to b e authorized.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show mac access-group interface show mac access-group interface To disp lay the ACL con figuratio n o n a Layer 2 interface, use th e show mac access-group interface co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show mac-address-table address show mac-address-table address To display MAC address table information for a specific MAC ad dress, use the show mac-address-table address command. show mac-address-ta ble address mac_addr [interface typ e slot/po rt | protocol protocol | vlan vlan_ id] Syntax Description mac_addr interfa ce type slot/port protocol protocol v lan vlan_id 48 -bit MAC ad dress; the valid format is H.H.H.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show mac-address-table address Related Commands Co mmand show ma c-address-table aging-time Description Displays MAC ad dress tab le aging information. show ma c-address-table count Displays the number of entries currently in the MAC ad dress tab le. show mac-address-table dynamic Displays the dynamic MAC ad dress tab le entries only.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show mac-address-table aging-time show mac-address-table aging-time To display the MAC addres s aging time, us e the show mac-a ddress-ta ble aging-time co mmand . show mac-address-ta ble aging-time [v lan vlan_id ] Syntax Description v lan vlan_id Defaults This command has no default setting s. Command Modes Examples (Optio nal) Sp ecifies a VLAN; valid values are fro m 1 to 409 4.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show mac-address-table count show mac-address-table count To disp lay the n umber of entries curren tly in the MAC ad dress tab le, use the sho w mac-a ddress-table co unt command. show ma c-addres s-table count [vlan vlan_id] Syntax Description vlan vlan _id Defaults This comman d has no default settings. Command Modes Examples (Optional) Specifies a VLAN; valid values are from 1 to 4 094.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show mac-address-table dynamic show mac-address-table dynamic To display the dy namic MAC address table entries o nly, use the show ma c-address-table dynamic command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show mac-address-table dynamic 2 0000.0000.0104 2 0000.0000.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show mac-address-table interface show mac-address-table interface To display the MAC address table information for a s pecific interface, use th e show mac-address-table interface co mmand . show mac-address-ta ble interface typ e slot/po rt Syntax Description type slo t/port Interface typ e; valid values are ethernet, fastethernet, gig abitethernet, and tengig abitethernet. Number of th e slot and port.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show mac-address-table interface Co mmand Description show ma c-address-table protocol Displays the MAC address table in formatio n th at is based on the p rotocol. Displays the static MAC address table entries on ly. show ma c-address-table static show ma c-address-table vlan Displays information about the MAC address table for a specific VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show mac address-table learning show mac address-table learning To display the status of MAC address learning for all VLANs or a s pecified VLAN, use th e show mac address-table learning u ser EXEC command. show mac address-table learning [vlan vla n-id] [ | {begin | exclude | include} exp ression] Syntax Description v lan vlan-id | begin (Optio nal) Displays information for a sp ecific VLAN. The ran ge is 1 to 4 094.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show mac-address-table multica st show mac-address-table multicast To disp lay information about the multicast MAC address table, u se the s how mac-address-table multicast co mmand. show ma c-addres s-table multica st [count | {igmp-snooping [count]} | {user [count]} | {vlan vlan _num}] Syntax Description Defaults co unt igmp-snooping (Option al) Displays the nu mber of multicast entries.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show mac-address-table multicast Command Descriptio n show mac-address-ta ble interface Displays the MAC add ress table info rmation for a specific in terface. Displays the MAC ad dress tab le information that is b ased o n th e protocol. Displays the static MAC ad dress tab le entries only.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show mac-add ress-table notification show mac-address-table notification To disp lay the MAC addres s table notificatio n s tatus and history, use th e show mac-address-table notification command. show ma c-addres s-table notifica tion [change] [interface [interface-id]] | [mac-move] | [threshold] | [learn-fail ] Syntax Description change interface (Optional) Dis play s th e MAC add ress change notification statu s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show mac-address-table notification Operation: Added Vlan: 1 MAC Addr: 1234.5678.9ab3 Dot1dBasePort: 323 Operation: Added Vlan: 1 MAC Addr: 1234.5678.9ab4 Dot1dBasePort: 323 History Index 3, Entry Timestamp 484334, Despatch Timestamp 484334 MAC Changed Message : Operation: Deleted Vlan: 1 MAC Addr: 1234.5678.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show mac-address-table protocol show mac-address-table protocol To disp lay the MAC addres s table in formatio n that is based on th e protocol, use the show mac-addres s-table protocol command. show ma c-addres s-table pro tocol {assigned | ip | ipx | other} Syntax Description assigned ip Specifies the assigned protocol entries . Specifies the IP protocol en tries. ipx Specifies the IPX pro to co l entries.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show mac-address-table protocol 2 Fa6/1 Fa6/2 0000.0000.0104 0030.94fc.0dff 0030.94fc.0dff dynamic other static ip,ipx,assigned,other static ip,ipx,assigned,other FastEthernet6/16 Switch Switch Multicast Entries vlan mac address type ports -------+---------------+-------+------------------------------------------1 ffff.ffff.ffff system Switch,Fa6/15 2 ffff.ffff.ffff system Fa6/16 1002 ffff.ffff.ffff system 1003 ffff.ffff.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show mac-address-table static show mac-address-table static To display the static MAC address tab le entries only, use the show mac-addres s-table static co mmand . show ma c-addres s-table static [address mac_a ddr | interface typ e number | protocol protocol | vlan vlan _id] Syntax Description address mac_addr interface type nu mber (Option al) Specifies a 48-bit MAC address to match ; the valid format is H.H.H.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show mac-address-table static 1004 ffff.ffff.ffff 1005 ffff.ffff.ffff Fa6/1 ffff.ffff.ffff Fa6/2 ffff.ffff.ffff . .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show ma c-address-table vlan show mac-address-table vlan To disp lay information about the MAC addres s table for a specific VLAN, use the show mac-addres s-table vlan co mmand . show ma c-addres s-table [vlan vlan_ id] [proto col protocol] Syntax Description vlan vlan _id protocol p roto col Defaults Command Modes Usage Guidelines (Option al) Displays the entries for a sp ecific VLAN; valid values are from 1 to 40 94.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show mac-address-table vlan -------+---------------+--------+---------------------+-------------------1 0000.0000.0203 dynamic other FastEthernet6/15 1 0000.0000.0204 dynamic other FastEthernet6/15 1 0030.94fc.0dff static ip,ipx,assigned,other Switch Multicast Entries vlan mac address type ports -------+---------------+-------+------------------------------------------1 ffff.ffff.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show macro auto mac-address-group show macro auto mac-address-group Use th e show macro a uto mac-a ddress-group command to display the configuration of MAC ad dress gro up.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show macro auto device show macro auto device Use the sho w macro a uto device glob al configu ration command to disp lay the default in formatio n for a device, including bu iltin function name and the p arameters that can be provided fo r the commands when execu tin g the builtin function.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show macro auto interface show macro auto interface Use the show macro auto interfa ce command to display Auto SmartPorts s tatus and the functions ap plied on an interface. show ma cro auto interface interface_ id Syntax Description interface_id Defaults Non e Sp ecifies an interface ID.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show macro auto monitor clients show macro auto monitor clients To display the clients u sing the device classifier facility on th e switch, use the show macro auto monitor clients user EXEC command. show macro auto monito r clients Syntax Description This command has no arguments or keywo rds.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show macro auto monitor device show macro auto monitor device To disp lay the devices conn ected to a switch and their associated properties, u se the sho w macro a uto monitor device user EXEC command. show ma cro auto mo nitor device [detail | filter string | interface interface_ id | mac-address mac_ad dress ] Syntax Description detail filter s tring Displays detailed dev ice classifier information.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show macro auto monitor device ========================================================================================== ======= This example shows how to u se the show macro auto monitor device p rivileged EXEC command with th e optio nal interfa ce key word to view summary in formatio n ab out the device con nected to the specified in terface: Switch# show macro auto monitor device interface gi 1/0/2 MAC_Address Port_Id Profile Name
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show macro auto monitor type show macro auto monitor type To disp lay all th e device types recog nized by the d evice clas sifier, use the show macro auto monitor type user EXEC command. show ma cro auto mo nitor type [table [built-in | default] | string filter_strin g] Syntax Description table built-in Displays dev ice classification in a tab le. Displays dev ice classification info rmation from the built-in device table.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show macro auto monitor type Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Invalid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Default Default Default D
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show macro auto monitor type Valid Valid Valid Valid Related Commands Built-in Built-in Built-in Built-in Cisco-Access-Point Cisco-AIR-LAP Cisco-AIR-AP Linksys-Device 10 30 30 20 21 22 23 24 Co mmand macro a uto device Description Co nfigures macro default parameter values. macro auto execute (built-in function) Co nfigures mappin g from an event trig ger to a built-in macro.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show module show module To display info rmation ab out the mod ule, use th e show module command. show module [mod | all] Syntax Description mod a ll Defaults This command has no default setting s. (Optional) Number of th e module; valid values vary fro m chassis to chassis. (Optional) Displays info rmation for all modu les.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show module Mod MAC addresses Hw Fw Sw Status --- ---------------------------------- ------ ------------ ------------ ------2 0001.6461.39c0 to 0001.6461.39c1 1.1 6.1(3) 6.2(0.97) Ok Mod Sub-Module Model Serial Hw Status --- --------------------------- --------------- --------------- ------- ------2 Policy Feature Card 2 WS-F6K-PFC2 SAD04440HVU 1.0 Ok 2 Cat4k MSFC 2 daughterboard WS-F6K-MSFC2 SAD04430J9K 1.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show monitor show monitor To display info rmation ab out the SPAN session , use the show monitor co mmand . show monito r [s essio n] [range session-range | loca l | remote | all | sessio n-n umber] [detail] Syntax Description session range session -rang e lo cal (Option al) Displays the SPAN in formatio n for a session. (Option al) Displays information fo r a ran ge of sessio ns. (Option al) Specifies a range of sessions.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show monitor This examp le shows how to d isplay th e detailed SPAN information for session 1: Switch# show monitor session 1 detail Session 1 --------Type : Local Session Source Ports : RX Only : None TX Only : None Both : Gi1/1, CPU Source VLANs : RX Only : None TX Only : None Both : None Source RSPAN VLAN : Fa6/1 Destination Ports : Fa6/1 Encapsulation : DOT1Q Ingress : Enabled, default VLAN = 2 Filter VLANs : None Filter Types RX : Goo
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show monitor capture show monitor capture To display the capture point details, so that y ou can see what capture p oints are defined, what their attribu tes are, and wh ether they are active, u se the show monitor capture co mmand . show monitor capture [na me [para meter] | buffer [brief | detailed | dump]] Syntax Description Defaults n ame parameter Specifies the capture po int n ame.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show monitor capture 19.000000 10.1.1.234 -> 20.1.1.2 UDP Source port: 20001 Destination port: 20002 20.000000 10.1.1.235 -> 20.1.1.2 UDP Source port: 20001 Destination port: 20002 21.000000 10.1.1.236 -> 20.1.1.2 UDP Source port: 20001 Destination port: 20002 … Switch# show monitor capture mycap buffer detailed Frame 1: 256 bytes on wire (2048 bits), 256 bytes captured (2048 bits) Arrival Time: Apr 15, 2012 15:50:02.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show monitor capture file show monitor capture file To d ecode and d isplay pack ets from a previou sly cap tured .pcap file, use the show mo nitor capture file command. show monitor capture file na me [displa y-filter filter-string] [brief | detailed | dump] Syntax Description n ame display-filter filter-strin g brief | deta iled | dump Specfies th e filename.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches sh ow mon itor capture file 8 7.000000 20002 9 8.000000 20002 10 9.000000 20002 11 10.000000 20002 12 11.000000 20002 13 12.000000 20002 14 13.000000 20002 15 14.000000 20002 16 15.000000 20002 17 16.000000 20002 18 17.000000 20002 19 18.000000 20002 20 19.000000 20002 21 20.000000 20002 22 21.000000 20002 23 22.000000 20002 24 23.000000 20002 25 24.000000 20002 26 25.000000 20002 27 26.000000 20002 28 27.000000 20002 29 28.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show monitor capture file 40 39.000000 20002 41 40.000000 20002 42 41.000000 20002 43 42.000000 20002 44 43.000000 20002 45 44.000000 20002 46 45.000000 20002 47 46.000000 20002 48 47.000000 20002 49 48.000000 20002 50 49.000000 20002 51 50.000000 20002 52 51.000000 20002 53 52.000000 20002 54 53.000000 20002 55 54.000000 20002 56 55.000000 20002 57 56.000000 20002 58 57.000000 20002 59 58.000000 20002 10.1.1.179 -> 20.1.1.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches sh ow mon itor capture file Address: 00:00:00:00:03:01 (00:00:00:00:03:01) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default) Type: IP (0x0800) Frame check sequence: 0x03b07f42 [incorrect, should be 0x08fcee78] Internet Protocol, Src: 10.1.1.140 (10.1.1.140), Dst: 20.1.1.2 (20.1.1.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show nmsp show nmsp To display the Network Mob ility Serv ices Protocol (NMSP) information for the switch, use th e show nmsp command. This command is available only when y our switch is running the cryptog raphic (encrypted) so ftware image.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show nmsp Attachment notify interval: 30 sec (default) Location notify interval: 30 sec (default) Switch# This is an example of output from the s how nmsp statistics connection and show nmsp statistics summary commands: Switch# show nmsp statistics connection NMSP Connection Counters ---------------------------------Connection 1: Connection status: UP Freed connection: 0 Tx message count ----------------------Subscr Resp: 1 Capa Notif: 1
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show nmsp Mobility Services Subscribed: MSE IP Address Services --------------------172.19.35.109 Attachment, Location Switch# Related Commands Command clear nms p statistics nmsp Description Clears the NMSP statistic coun ters. Config ures Network Mobility Services Protocol (NMSP) on the switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show pagp show pagp To disp lay information about the port channel, use the show pagp comman d. show pagp [group-number] {counters | dual-active | interna l | neig hbor} Syntax Description group-number co unters dual-active Defaults (Optio nal) Ch ann el-group number; valid values are fro m 1 to 64. Specifies the traffic co unter information. Specifies the dual-active info rmation. internal Specifies the PAgP internal in formatio n.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show pagp Gi1/44 Yes VS3 Gi1/1/44 1.1 Gi1/45 Yes VS3 Gi1/1/45 1.1 Gi1/46 Yes VS3 Gi2/1/46 1.1 Gi1/47 Yes VS3 Gi2/1/47 1.1 Gi1/48 Yes VS3 Gi2/1/48 1.1 Gi2/3 Yes VS3 Gi1/1/1 1.1 Gi2/4 Yes VS3 Gi2/1/1 1.1 Switch# This example s hows how to display internal PAgP info rmation: Switch# show pagp 1 internal Flags: S - Device is sending Slow hello. A - Device is in Auto mode. Timers: H - Hello timer is running. S - Switching timer is running.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show policy-map show policy-map To disp lay information about the policy map, use the show policy -map command. show policy-map [policy_ map_ name] Syntax Description policy_ map_ name Defaults This comman d has no default settings. Command Modes Examples (Optional) Name o f the p olicy map.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show policy-map control-plane show policy-map control-plane To display the config uration either of a class o r of all classes for the policy map of a control plane, use th e show policy-map control-plane co mmand. show policy-map co ntro l-plane [input [cla ss class-name] | [class clas s-na me]] Syntax Description input class class-name Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show policy-map control-plane Class-map: system-cpp-cgmp (match-all) 0 packets Match: access-group name system-cpp-cgmp Class-map: system-cpp-ospf (match-all) 0 packets Match: access-group name system-cpp-ospf Class-map: system-cpp-igmp (match-all) 0 packets Match: access-group name system-cpp-igmp Class-map: system-cpp-pim (match-all) 0 packets Match: access-group name system-cpp-pim Class-map: system-cpp-all-systems-on-subnet (match-all)
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show policy-map control-plane Table 2-30 show policy-map control-plane Field Descriptions (continued) Field Descriptio n Class-map Class o f traffic b eing disp layed. Traffic is displayed for each configured class. The choice fo r implementing class matches (fo r examp le, match-all o r match-any) can also app ear n ext to th e traffic class. Match Match criteria for the specified class of traffic.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show policy-map interface show policy-map interface To disp lay the statistics an d con figuratio ns of the in put an d o utput policies that are attached to an interface, use th e show policy-map interface co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show policy-map interface 0 packets match:any 0 packets Switch# This example shows how to disp lay the inpu t policy statistics and configuration s for a specific in terface: Switch# show policy-map interface fastethernet 5/36 input service-policy input:ipp5-policy class-map:ipp5 (match-all) 0 packets match:ip precedence 5 set: ip precedence 6 class-map:class-default (match-any) 0 packets match:any 0 packets Switch# With the following
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show policy-map interface Switch# show policy-map interface FastEthernet6/1 Service-policy input: p1 Class-map: c1 (match-all) 15432182 packets Match: flow ip source-address ip destination-address ip protocol l4 source-port l4 destination-port police: Per-interface Conform: 64995654 bytes Exceed: 2376965424 bytes Class-map: class-default (match-any) 0 packets Match: any 0 packets Switch# Related Commands Co mmand cla ss-map Description
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show policy-map interface vlan show policy-map interface vlan To show the QoS policy-map info rmation ap plied to a specific VLAN on an interface, use the show policy-map interface vlan comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show policy-map interface vlan Class-map: class-default (match-any) 0 packets Match: any 0 packets Switch# The following example shows a configuration on a Su pervisor Engin e 6-E: interface gigabitethernet3/1 vlan-range 100 service-policy in p1 This examp le shows how to d isplay p olicy-map s tatistics on VLAN 100 on the FastEth ernet interface: Switch# show policy-map interface gigabitethernet 3/1 vlan 100 GigabitEthernet3/1 vlan 100
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show port-security show port-security To display the po rt security settin gs for an interface o r fo r the switch , use the show port-security command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show port-sec urity Fa3/14 1 0 0 Shutdown Fa3/15 1 0 0 Shutdown Fa3/16 1 0 0 Shutdown Po2 3 1 0 Shutdown --------------------------------------------------------------------------Total Addresses in System (excluding one mac per port) :8 Max Addresses limit in System (excluding one mac per port) :3072 Global SNMP trap control for port-security :20 (traps per second) Switch# This examp le shows how to d isplay p ort secu rity settings for i
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show port-security This example s hows how to display all secure MAC addresses config ured on all switch interfaces: Switch# show port-security address Secure Mac Address Table ------------------------------------------------------------------Vlan Mac Address Type Ports Remaining Age (mins) --------------------------------1 0000.0001.0000 SecureConfigured Fa3/1 15 (I) 1 0000.0001.0001 SecureConfigured Fa3/1 14 (I) 1 0000.0001.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show port-sec urity 4 0001.0001.0001 SecureConfigured Gi1/1 4 0001.0001.0003 SecureSticky Gi1/1 6 0001.0001.0001 SecureConfigured Gi1/1 6 0001.0001.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show port-security 4 0001.0001.0003 SecureSticky Gi1/1 5 0001.0001.0001 SecureConfigured Gi1/1 6 0001.0001.0001 SecureConfigured Gi1/1 6 0001.0001.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show port-sec urity 4 5 6 Switch# 22 22 22 3 1 2 This example shows h ow to dis play the p ort s ecurity settin gs on in terface Gigab itethern et1/1 for VLANs 2 and 3 : Switch# show port-security interface gigabitethernet1/1 vlan 2-3 Default maximum: 22 VLAN Maximum Current 2 22 3 3 22 3 Switch# This examp le shows how to d isplay all secure MAC ad dresses con figured o n in terface Gigabitethernet1/1 with aging information for each a
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show power show power To display info rmation ab out the power statu s, use the show power command. show power [availa ble | capabilities | detail | inline {[interface] deta il | consumption default | module mo d detail}} | module | status | s upplies] Syntax Description ava ilable capabilities detail (Optio nal) Displays detailed information on power resources. (Optio nal) Displays the PoE s tatus.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show power Power supplies needed by system :1 Power supplies currently available :1 Power Summary (in Watts) ---------------------System Power (12V) Inline Power (-50V) Backplane Power (3.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show power Fa3/3 Fa3/4 Fa3/5 Fa3/6 Fa3/7 Fa3/8 Fa3/9 Fa3/10 Fa3/11 Fa3/12 Fa3/13 Fa3/14 Fa3/15 Fa3/16 Fa3/17 Fa3/18 auto auto auto auto auto auto auto auto auto auto auto auto auto auto auto auto on on on on on on on on off off off off off off off off 7.1 7.1 17.3 17.3 4.5 7.9 17.3 17.3 0 0 0 0 0 0 0 0 6.3 6.3 15.4 15.4 4.0 7.0 15.4 15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show power Power Summary Maximum (in Watts) Used Available --------------------------------System Power (12V) 360 360 Inline Power (-50V) 0 0 Backplane Power (3.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show power Mod Model ---- ----------------1 WS-X4013+TS ----------------------- Watts used of Module Inline Power (12V -> -50V) Inline Power Admin Inline Power Oper PS Device PS Device Efficiency ---------------------------------------6 5 3 3 90 ---------------------------------------- Switch# This example s hows how to display detailed information on the Po E status for Gigab it interface 2/1: Switch# show power inline g2/1 detail Av
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show power Device Detected: no Device Type: n/a IEEE Class: n/a Discovery mechanism used/configured: Ieee and Cisco Police: off Power Allocated Admin Value: 20.0 Power drawn from the source: 0.0 Power available to the device: 0.0 Actual consumption Measured at the port: 0.0 Maximum Power drawn by the device since powered on: 0.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show power Over Current Counter: 0 Short Current Counter: 0 Invalid Signature Counter: 0 Power Denied Counter: 0 Interface: Gi3/4 Inline Power Mode: auto Operational status: off Device Detected: no Device Type: n/a IEEE Class: n/a Discovery mechanism used/configured: Ieee and Cisco Police: off Power Allocated Admin Value: 20.0 Power drawn from the source: 0.0 Power available to the device: 0.0 Actual consumption Measured at the port: 0.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show power Power drawn from the source: 0.0 Power available to the device: 0.0 ................ Related Commands Co mmand power dc input Description Config ures the power DC input parameters o n th e switch. power inline Sets the in line-power state for the inline-power-cap able interfaces. Sets the d efau lt po wer that is allocated to an interface for all the inline-power-capable interfaces on the switch .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show power inline police show power inline police To display Po E policing an d mo nitoring status , use the show power inline police comman d. show power inline police [interfacena me] [module n] Syntax Description in terfacename module n Defaults This command has no default setting s. Command Modes Priv ileged EXEC mo de Usage Guidelines (op tional) Disp lays PoE policing and monitoring status for a particular interface.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show pppoe intermediate-a gent interface show pppoe intermediate-agent interface To disp lay PPPo E Intermediate Agen t configuration and statistics (packet cou nters), use the show pppoe intermediate-agent interface command. show ppo e intermediate-ag ent information interface interface show ppo e intermediate-ag ent statistics interface interface Syntax Description interface interface Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show pppoe intermediate-agent interface Related Commands Command pppoe intermediate-agent (global) pppoe intermediate-agent format-type (global) pppoe intermediate-agent (interface) Descriptio n Enab les the PPPoE Intermediate Agent feature on a switch. pppoe intermediate-agent format-type (interface) Sets circuit-id or remo te-id for an interface.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show qos show qos To disp lay QoS information , use the show qos comman d. show qos Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show qos aggregate policer show qos aggregate policer To display QoS ag gregate policer info rmation, use the show qos aggrega te policer comman d. show qos ag gregate policer [agg reg ate_ name] Syntax Description ag gregate_name Defaults This command has no default setting s. (Optio nal) Named aggregate p olicer. Command Modes Priv ileged EXEC mo de Usage Guidelines The aggregate p olicer name is case sensitiv e.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show qos dbl show qos dbl To disp lay glob al Dy namic Buffer Limiting (DBL) information , use the show qos dbl comman d. show qos dbl Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show qos interface show qos interface To display queueing info rmation, u se the sho w qo s interfa ce command. show qos interface { fastethernet in terface-nu mber | gigabitethernet interface-number} | [vlan vla n_id | port-channel number ] Syntax Description Defaults fastethernet in terface-nu mber g igabitethernet interface-number Specifies the Fas t Eth ernet 8 02.3 interface. Specifies the Gigab it Ethernet 8 02.3z interface.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show qo s maps show qos maps To disp lay QoS map info rmation, u se the sho w qo s maps co mmand . show qos maps [cos | dscp [policed | tx -queue]] Syntax Description Defaults Command Modes Examples co s dscp (Optional) Dis play s CoS map in formatio n. (Optional) Dis play s DSCP map in formatio n. policed (Optional) Dis play s p oliced map in formatio n. tx-queue (Optional) Dis play s tx -queue map information .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show qos maps CoS: 0 1 2 3 4 5 6 7 -------------------------------DSCP: 0 8 16 24 32 40 48 56 Switch# Related Commands Command qos account la yer-all encapsulation Descriptio n Globally enables QoS fun ction ality on the switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show re dundancy show redundancy To disp lay redu ndancy facility information, use the show redundancy command. show redundancy { clients | counters | history | s tates} Syntax Description Defaults clients co unters (Op tional) Disp lays information about the redund ancy facility client. (Op tional) Disp lays information about the redund ancy facility coun ter.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show redundancy Uptime in current state = 2 days, 2 hours, 39 minutes Image Version = Cisco Internetwork Operating System Software IOS (tm) Catalyst 4000 L3 Switch Software (cat4000-I5S-M), Version 12.2(20)EWA(3 .92), CISCO INTERNAL USE ONLY ENHANCED PRODUCTION VERSION Copyright (c) 1986-2004 by cisco Systems, Inc. Compiled Wed 14-Jul-04 0 BOOT = bootflash:cat4000-i5s-mz.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show re dundancy 00:00:03 00:00:25 00:00:25 00:00:25 00:00:25 00:00:25 00:00:25 00:00:25 00:00:25 00:00:25 00:00:25 00:00:25 00:00:25 00:00:25 00:01:34 00:01:34 00:01:34 00:01:34 00:01:36 00:01:36 00:01:36 00:01:36 00:01:38 Switch# *my state = NEGOTIATION(3) peer state = DISABLED(1) RF_EVENT_GO_ACTIVE(511) op=0 *my state = ACTIVE-FAST(9) peer state = DISABLED(1) RF_STATUS_MAINTENANCE_ENABLE(403) Redundancy Mode RF(30) op=0 RF_STATUS_MAINT
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show redundancy config-sync show redundancy config-sync To display an ISSU con fig-sync failure or th e ignored mismatch ed comman d list (MCL), if any, use the show redundancy config-sync comman d. show redundancy config-sync {fa ilures | ignored} {bem | mcl| prc} show redundancy config-sync ignored failures mcl Syntax Description Defaults failures ig nored bem Displays MCL entries or BEM/PRC failures.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show redundancy config-sync Note Step 3 If you igno re th e mismatched commands , the ou t-of-syn c configu ration at the active superviso r engine an d th e standby sup ervisor engin e still exists. You can verify the ig nored MCL with the show redundancy config -sync ig no red mcl comman d. Each co mmand sets a return cod e in the actio n function th at imp lements th e command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show running-config show running-config To display the mod ule status an d con figuratio n, use the show running-config command. show running-co nfig [module slot] Syntax Description module slot Defaults This command has no default setting s. (Optio nal) Sp ecifies the mod ule slot numb er; valid valu es are from 1 to 6.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show running-config duplex auto speed auto Switch# This examp le shows the outpu t for the show running -config co mmand when you have en abled the switchport voice vla n comman d: Switch# show running-config int fastethernet 6/1 Building configuration...
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show shell functions show shell functions Use the show shell functions co mmand to disp lay configurations for all bu iltin s hell functions. show shell functions Syntax Description No keywords Defaults None Command Modes Priv iledg ed EXEC Usage Guidelines This command on ly d isplay s th e contents of builtin shell fun ctions . To d isplay th e contents o f user created functions, use the show shell trigg ers command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show shell triggers show shell triggers Use the show shell triggers comman d to disp lay d etail fo r all supp orted builtin an d user created trigg ers. show shell triggers Syntax Description No key words Defaults Non e Command Modes Usage Guidelines Examples Privileg ed EXEC This comman d displays builtin triggers and user d efin ed triggers (with their map ped functions).
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show slavebootflash: show slavebootflash: To d is play information abo ut the standby bootflash file system, use the show slavebo otflash: command. show slavebootflash: [all | chips | filesy s] Syntax Description a ll chips (Optional) Dis play s all possible Flash information. (Optional) Dis play s Flash ch ip in formatio n. filesy s (Optional) Dis play s file system info rmation. Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show slavebootflash: This examp le shows how to d isplay all bootflash in formatio n: Switch# show slavebootflash: all -# - ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name 1 .. image 8C5A393A 237E3C 14 2063804 Aug 23 1999 16:18:45 c4-bootmz 2 .. image D86EE0AD 957CE8 9 7470636 Sep 20 1999 13:48:49 rp.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show slaveslot0: show slaveslot0: To d isplay information ab out th e file system on the standby superv isor en gine, use the show slaves lot0: command. show slo t0: [all | chips | filesys] Syntax Description a ll chips filesy s (Optio nal) Displays all flash information includin g th e outpu t fro m the show slot0 : chips and show slot0: filesys commands. (Optio nal) Displays flash chip register information.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show slaveslot0: B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 COMMON MEMORY REGISTERS: Bank 2 Intelligent ID Code : 8989A0A0 Compatible Status Reg: 8080 Global Status Reg: B0B0 Block Status Regs: 0 : B0B0 B0B0 B0B0 B0B0 B0B0 8 : B0B0 B0B0 B0B0 B0B0 B0B0 16 : B0B0 B0B0 B0B0 B0B0 B0B0 24 : B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 COMMON MEMORY REGISTERS: B
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show slot0: show slot0: To display info rmation ab out the slot0 : file system, u se the s how slot0 : co mmand . show slo t0: [all | chips | filesys] Syntax Description a ll chips filesy s (Optio nal) Displays all flash in fo rmatio n in clud ing the ou tput from the show slot0: chips and show slot0: filesys commands. (Optio nal) Displays flash chip register information. (Optio nal) Displays file system status information.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show slot0: B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 COMMON MEMORY REGISTERS: Bank 2 Intelligent ID Code : 8989A0A0 Compatible Status Reg: 8080 Global Status Reg: B0B0 Block Status Regs: 0 : B0B0 B0B0 B0B0 B0B0 B0B0 8 : B0B0 B0B0 B0B0 B0B0 B0B0 16 : B0B0 B0B0 B0B0 B0B0 B0B0 24 : B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 B0B0 COMMON MEMORY REGISTERS: Bank 3 Intelligent ID Code
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show spanning-tree show spanning-tree To display spanning-tree s tate in formatio n, us e the show s panning-tree command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show spanning-tree Port path cost 19, Port priority 128, Port Identifier 129.9. Designated root has priority 16384, address 0060.704c.7000 Designated bridge has priority 32768, address 00e0.4fac.b000 Designated port id is 128.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show spanning-tree Root ID Priority 32768 Address 0030.94fc.0a01 This bridge is the root Hello Time 2 sec Max Age 20 sec Bridge ID Priority 32768 Address 0030.94fc.0a01 Hello Time 2 sec Max Age 20 sec Aging Time 300 Interface Name ------------------FastEthernet6/16 Switch# Port ID Prio Cost Sts ------- --- ------ --129.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show spanning-tree PortFast BPDU Guard is disabled EtherChannel misconfiguration guard is enabled UplinkFast is disabled BackboneFast is disabled Default pathcost method used is short Name Blocking Listening Learning Forwarding STP Active -------------------- -------- --------- -------- ---------- ---------VLAN1 0 0 0 1 1 VLAN2 0 0 0 1 1 -------------------- -------- --------- -------- ---------- ---------2 VLANs 0 0 0 2 2 Switch# This ex
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show spanning-tree mst show spanning-tree mst To display MST proto co l information , use the show spanning -tree mst comman d. show spanning-tree mst [co nfiguration] show spanning-tree mst [instance-id] [detail] show spanning-tree mst [instance-id] interface interface [detail] Syntax Description Defaults configuration in stance-id (Optio nal) Displays region config uration information.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show spanning-tree mst GigabitEthernet1/1 of MST03 is boundary forwarding Port info port id 128.1 priority 128 cost 20000 Designated root address 0002.172c.f400 priority 32771 cost 0 Designated bridge address 0002.172c.f400 priority 32771 port id 128.1 Timers: message expires in 0 sec, forward delay 0, forward transitions 1 Bpdus (MRecords) sent 4, received 0 FastEthernet4/2 of MST03 is backup blocking Port info port id 128.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show storm-control show storm-control To display the broadcast storm con trol settings on the switch o r on the sp ecified interface, use th e show storm-contro l command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show storm-control Switch# This is an example of output from the s how s torm-control command fo r a sp ecified interface: Switch# show storm-control fastethernet2/17 Interface Filter State Level Current --------- ------------- ------- ------Fa2/17 Forwarding 50.00% 0.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show system mtu show system mtu To display the glo bal MTU setting , use the show sy stem mtu command. show sy stem mtu Syntax Description This command has no arguments or keywo rds. Defaults This command has no default setting s. Command Modes Examples Priv ileged EXEC mo de This example s hows how to display the g lobal MTU setting: Switch# show system mtu Global Ethernet MTU is 1550 bytes.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches sho w tech-support show tech-support To disp lay troubleshoo tin g information for TAC, us e the show tech-support comman d. show tech-support [bridging | cef | ipmulticas t | isis | pass word [pa ge] | page] Syntax Description bridging cef (Optional) Specifies bridging-related informatio n. (Optional) Specifies CEF-related info rmation. ipmulticast (Optional) Specifies IP multicast-related information .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show tech-support • show process cpu • show buffers • show lo gging • • show module show power • show env ironment • show interfa ces switchport • • show interfa ces trunk show v lan If you enter the ipmulticast keywo rd, the ou tput displays the equivalent of th ese show co mmand s: • • • show ip pim interface show ip pim interface count show ip pim neighbor • show ip pim rp • show ip igmp groups • • show ip igmp in
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show udld show udld To disp lay the admin istrative and operation al UDLD status, use the show udld priviledged EXEC co mmand . show udld interface-id | neighbors | fast-hello {interfa ce id} Syntax Description interface id neighbors Specifies the administrative and op eratio nal UDLD status for a sp ecific in terface. Specifies the UDLD n eigh bor su mmary.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show udld No TLV fast-hello interval TLV Time out interval: 5 TLV CDP Device name: Switch To verify lin k s tatus as reported by UDLD, enter the following command: Switch# show udld neighbors Port ---Gi1/33 Gi1/34 Device Name ----------FOX10430380 FOX10430380 Device ID --------1 1 Port ID ------Gi1/33 Gi1/34 Neighbor State -------------Bidirectional Bidirectional To verify Fast UDLD con figuratio n, enter the followin g command: Sw
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show udld Co mmand Description udld (glo ba l configuratio n mode) Enables aggressive or normal mode in the UDLD protocol and sets the configurable message timer time. Enables UDLD on an in div idual in terface or prevents a fiber interface from b eing enabled b y th e udld (g lobal co nfiguration mode) comman d. udld (interface configuration mode) Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show vlan show vlan To display VLAN information, use th e show vlan co mmand . show v lan [brief | id vlan_ id | name na me] show v lan private-v lan [typ e] Syntax Description brief id vla n_id name na me (Optio nal) Dis play s only a single line fo r each VLAN, namin g the VLAN, status, an d p orts. (Optio nal) Displays information about a sin gle VLAN identified b y VLAN ID n umber; valid values are from 1 to 4094.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show vlan 3 4 5 6 10 20 50 enet enet enet enet enet enet enet 100003 100004 100005 100006 100010 100020 100050 1500 1500 1500 1500 1500 1500 1500 - - - - 1005 - 0 3276 - 15 srb ieee ibm - - 303 304 305 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 <...Output truncated...
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show vlan Table 2-32 Field VLAN Name show vlan Command Output Fields Descriptio n VLAN number. Name, if con figured, of the VLAN. Status Status of the VLAN (active or sus pen d). Ports Ports that belong to the VLAN. Type Media type of the VLAN. SAID Secu rity Ass ociation Iden tifier value fo r the VLAN. MTU Maximum trans mis sion unit size fo r the VLAN. Parent Parent VLAN, if one exists.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show vlan a ccess-map show vlan access-map To disp lay the con tents of a VLAN access map, use th e show vlan access-map comman d. show vlan access-map [map-n ame] Syntax Description map -name Defaults This comman d has no default settings. Command Modes Examples (Optional) Name o f the VLAN access map.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show vlan counters show vlan counters To display the software-cached counter values, use the show vlan counters command. show v lan [id vlanid ] counters Syntax Description id vla nid Defaults This command has no default setting s. (Optio nal) Displays the software-cached counter values for a specific VLAN.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show vlan dot1q tag native show vlan dot1q tag native To disp lay all th e ports on the switch that are eligible for n ative VLAN tagg ing as well as their current native VLAN tagging status, u se the show vlan dot1q tag native comman d. show vlan do t1q tag native Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show vlan group show vlan group To disp lay the VLANs mapped to VLAN g rou ps, use the show vla n group privildeg ed EXEC command. show v lan group [gro up-na me gro up-n ame] Syntax Description group-name g rou p-n ame Defaults None (Optional) Dis play s th e VLANs mapped to the specified VLAN gro up.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show vlan intern al usage show vlan internal usage To display information about th e in ternal VLAN allocation , u se the show vlan internal usage comman d. show vlan [id vlan -id ] internal usa ge Syntax Description id vlan-id Defaults This comman d has no default settings. (Optional) Disp lays intern al VLAN allocation information for the specified VLAN; valid values are from 1 to 4094.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show vlan mapping show vlan mapping Use the show v lan mapping priv ileged EXEC command to d isplay in formatio n abou t VLAN mappin g o n trunk po rts. show v lan mapping [interface interface-id] [ | {begin | exclude | include} expressio n] Syntax Description Defaults interfa ce interfa ce-id | begin | exclude (Optional) Dis play s VLAN mapp ing info rmation fo r the sp ecified interface.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show vlan mtu show vlan mtu To d isplay the minimum an d max imum transmissio n unit (MTU) sizes o f each VLAN, use th e show vlan mtu command. show vlan mtu Syntax Description This comman d has no argu ments or keyword s Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show vlan private-vlan show vlan private-vlan To display private VLAN in formatio n, use the show v la n priv ate-v lan command. show vlan private-vlan [typ e] Syntax Description type Defaults This command has no default setting s. (Optio nal) Displays the private VLAN type; valid types are isolated, primary, commun ity, twoway-commun ity n onoperation al, and no rmal.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show vlan private-vlan 309 community 440 isolated Switch# Table 2 -33 describes the field s in the show vlan private-vlan co mmand ou tput. Table 2-33 show vlan private-vlan Command Output Fields Field Description Primary Numb er o f the p rimary VLAN. Secondary Numb er o f the secondary VLAN. Secondary-Type Related Commands Secondary VLAN type is isola ted or co mmunity. Ports Ind icates th e ports within a VLAN.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show vlan remote-span show vlan remote-span To d isplay a list o f Remo te SPAN (RSPAN) VLANs, use the show vlan remote-span command. show vlan remote-span Syntax Description This command has no arguments or keywo rds. Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show vmps show vmps To disp lay the VLAN Qu ery Protocol (VQP) versio n, reconfirmation interval, retry co unt, VLAN Memb ership Policy Server (VMPS) IP ad dresses, current servers, an d p rimary servers, use the show vmps comman d. show vmps [statistics] Syntax Description sta tistics Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show vtp show vtp To display VTP statistics and domain info rmation, u se the sho w vtp co mmand . show v tp {counters | s tatus} Syntax Description counters status Defaults This command has no default setting s. Command Modes Examples Specifies the VTP statistics. Specifies the VTP domain status.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches show vtp This examp le shows how to d isplay o nly those lin es in the show v tp output that con tain the word Summary: Switch# show vtp counters | include Summary Summary advertisements received : 1 Summary advertisements transmitted : 32 Trunk Join Transmitted Join Received Switch# Summary advts received from Table 2 -34 describes the field s in the show vtp comman d o utput.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches show vtp Command Descriptio n v tp pas sword vtp pruning v tp server Creates a VTP domain password. Enab les pruning in the VLAN datab ase. Places the device in VTP server mod e. v tp transpa rent Places dev ice in VTP transparent mode. vtp v2-mode Enab les versio n 2 mo de. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
2.2 Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches snmp ifin dex clear snmp ifindex clear To clear any previou sly con figured snmp ifindex commands that were entered fo r a specific in terface, use th e snmp ifindex clear co mmand . snmp ifindex clear Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches snmp ifindex persist snmp ifindex persist To enable ifIndex valu es in the In terfaces MIB (IF-MIB) th at p ersist across reb oots (ifIndex pers is tence) o n a specific interface, use the snmp ifindex persis t command. To dis able ifIn dex persistence only on a sp ecific interface, use the no form of this command. snmp ifindex pers ist no snmp ifindex persist Syntax Description This command has no arguments or keywo rds.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches snmp-server e nable traps snmp-server enable traps To enable SNMP notifications (traps or informs), u se the snmp-server enable traps command. To disable all SNMP no tifications , use the no form of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches snmp-server enable traps This list o f the MIBs is u sed for the traps: • flash—Controls SNMP FLASH traps from the CISCO-FLASH-MIB. – insertion—Controls the SNMP Flas h in sertion trap notifications. – removal— Co ntrols the SNMP Flash removal trap n otification s. • port-security—Contro ls th e port-security trap s fro m the CISCO-PORT-SECURITY-MIB. stpx—Controls all the traps from the CISCO-STP-EXTENSIONS-MIB.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches snmp-server ifindex persist snmp-server ifindex persist To glo bally enable ifInd ex values that will remain cons tant across reboo ts for u se by SNMP, use the snmp-server ifindex persist command. To glo bally disable inIndex persistence, use the no form of this co mmand . snmp-server ifindex persist no snmp-server ifindex persist Syntax Description Defaults Command Modes Usage Guidelines This comman d has no argu ments or keyword s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches snmp-server ifindex persist compress snmp-server ifindex persist compress To config ure the format of the ifInd ex table in a compressed format, use the snmp-s erver ifindex persist compress command. To place the table in a decomp ressed format, use the no form o f this co mmand . snmp-server ifindex persist compress no snmp-server ifindex persist co mpress Syntax Description This command has no arguments or keywo rds.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches snmp trap mac-notification change snmp trap mac-notification change To enab le SNMP MAC add ress no tification s, use the s nmp trap mac-notification command. To retu rn to the default setting, u se the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches source-interfac e source-interface To sen d out call home email messages with s pecific source interface, use th e source-interface command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches source-ip-address source-ip-address To send out Call Home email messag es with sp ecific source IP add ress, u s e the so urce-ip-address co mmand . source-ip-a ddress ip address Syntax Description ip address Defaults Non e Source IP address for Call Home messages.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches spanning-tree backbonefast spanning-tree backbonefast To enable Backb oneFast on a spannin g-tree VLAN, use the spanning-tree backbonefas t command. To d isable Backbon eFast, use the no fo rm of this command. spanning-tree backbonefast no spanning-tree backbonefast Syntax Description This command has no arguments or keywo rds. Defaults Back boneFast is disabled .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches span ning-tree bp dufilter spanning-tree bpdufilter To enab le BPDU filtering on an interface, use th e spanning-tree bpdufilter comman d. To retu rn to th e default setting s, use the no fo rm of this command. spanning-tree bpdufilter { enable | disable} no spanning-tree bpdufilter Syntax Description Defaults enable En ables BPDU filterin g on this interface. dis able Disables BPDU filterin g on this interface.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches spanning-tree bpdufilter Command Descriptio n show spanning-tree Displays spanning-tree in formatio n. spanning-tree portfast bpdufilter default Enab les the BPDU filtering by default o n all PortFast ports. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches spanning-tre e bpdu guard spanning-tree bpduguard To enable BPDU gu ard on an in terface, u se the spa nning-tree bpduguard co mmand . To return to the default setting s, use the no fo rm of this command. spanning-tree bpduguard {ena ble | disa ble} no spanning-tree bpduguard Syntax Description enable dis able En ables BPDU guard o n this interface. Disables BPDU guard o n this in terface. Defaults BPDU guard is disabled.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches spanning-tree cost spanning-tree cost To calcu late the p ath co st of STP o n an in terface, use th e spa nning-tree cost command. To revert to the d efault, use th e no form of this command . spanning-tree cost cost no spanning-tree cost cost Syntax Description cost Defaults The default settings are as follows: Path cost; valid valu es are from 1 to 20 0,000,000.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches spanning-tree etherchannel guard misconfig spanning-tree etherchannel guard misconfig To disp lay an erro r mess age when a loo p d ue to a channel miscon figuration is d etected, use the spanning-tree etherchannel guard mis config co mmand . To d isab le th e feature, use the no form of this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches spanning-tree extend system-id spanning-tree extend system-id To en able the extended s ystem ID feature on a chassis th at supp orts 10 24 MAC addres ses, use th e spanning-tree extend system-id command. To disable the feature, use the no form o f this co mmand . spanning-tree extend system-id no spanning-tree extend sys tem-id Syntax Description This command has no arguments or keywo rds.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches sp anning-tree guard spanning-tree guard To en able root guard, u se the spanning-tree gua rd command. To dis able root guard, u se the no form of this co mmand . spanning-tree guard {loop | roo t | none} no spanning-tree guard Syntax Description Defaults Command Modes Examples loop roo t En ables the lo op guard mode on the in terface. En ables ro ot g uard mode on the interface. none Sets the guard mod e to none.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches spanning-tree link-type spanning-tree link-type To configure a link type for a port, u se the spanning-tree link-type command. To return to the default settings, use the no form of this command. spanning-tree link-type {point-to-point | shared} no spanning-tree link-type Syntax Description point-to-point shared Specifies that the interface is a po int-to-poin t link . Specifies that the interface is a shared medium.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches spann ing-tree loopguard de fault spanning-tree loopguard default To enable loo p g uard as the default on all ports of a specific bridge, use the spanning-tree loo pg ua rd default co mmand . To d isab le loop gu ard, us e the no form of th is command. spanning-tree loopguard default no spanning-tree loopguard default Syntax Description This comman d has no keywo rds or arg umen ts. Defaults Loop g uard is disab led.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches spanning-tree mode spanning-tree mode To switch between PVST+ and MST mo des, use the spanning -tree mode comman d. To return to the d efault settings, use the no form o f this co mmand . spanning-tree mode {pvst | mst | rapid-pvst} no spanning-tree mode {pvst | ms t | rapid-pvst} Syntax Description Defaults pvst mst Specifies PVST+ mo de. Specifies MST mode. rapid-pvst Specifies Rapid PVST mode.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches spanning-tree mst spanning-tree mst To set the path cost and port-priority parameters for any MST instance (including the CIST with instance ID 0), use the spanning-tree mst comman d. To return to the default settings, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches spanning-tree mst configuration spanning-tree mst configuration To enter the M ST con figuratio n submod e, use the spanning-tree mst configuration command. To return to the default M ST configuration , use the no form of this comman d. spanning-tree mst configuration no spanning-tree mst configuration Syntax Description This command has no arguments or keywo rds.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches spanning-tree mst configuration Wh enever y ou change an M ST config uration submod e parameter, it can cau se a loss of con nectivity. To reduce the number of service disruption s, wh en yo u enter the MST con figuratio n s ubmode, y ou are ch ang ing a copy of the cu rren t MST config uration.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches spanning-tree mst forward-time spanning-tree mst forward-time To set the forward delay timer for all the instances, use the spanning -tree mst forward-time comman d. To return to th e default settin gs, use the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches spanning-tree mst hello-time spanning-tree mst hello-time To set the hello-time delay timer for all the instances, u se the spanning-tree mst hello-time command . To return to th e default settin gs, use the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches spanning-tree mst max-age spanning-tree mst max-age To set the max-age timer for all the instances, u se the spanning-tree mst max-age co mmand . To return to th e default setting s, use the no fo rm of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches spanning-tree mst max-hops spanning-tree mst max-hops To specify the number of possible hops in the region before a BPDU is discarded, use the spanning-tree mst max-hops command. To return to the default settings, use the no form o f this co mmand.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches spanning-tree mst root spanning-tree mst root To designate the primary root, second ary root, bridge priority, and timer value for an instance, u se the spanning-tree mst root command. To return to th e default settin gs, us e the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches spanning-tree pathcost method spanning-tree pathcost method To set the path cost calculation method, use the spanning-tree pathcost method command. To revert to the default setting, u se the no form of this command. spanning-tree pa thcost method {long | short} no s panning-tree pathcos t method Syntax Description long short Specifies 32-bit-based values for po rt path cos ts . Specifies 16-bit-based values for po rt path cos ts .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches spanning-tree portfast (interface configuration mode) spanning-tree portfast (interface configuration mode) To en able Po rtFas t mod e, where the interface is immediately pu t into th e fo rwarding state upon lin kup without waiting for the timer to expire, use the spanning-tree portfas t co mmand . To return to the d efault setting, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches spanning-tree portfast (interface configuration mode) Related Commands Co mmand spanning-tree co st Description Calculates the path cost of STP on an in terface. spanning-tree portfast default spanning-tree po rt-priority Enables PortFast by default on all access p orts. Prioritizes an interface when two bridges compete for position as the root brid ge.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches spanning-tree portfast bpdufilter default spanning-tree portfast bpdufilter default To enable th e BPDU filtering by default on all PortFast ports, use the s panning-tree portfast bpdufilter default command. To return to the default settings, u se the no form of this command. spanning-tree portfast bpdufilter default no spanning-tree portfast bpdufilter default Syntax Description This command has no key words or arguments.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches spanning-tree portfast bpduguard de fault spanning-tree portfast bpduguard default To en ab le BPDU g uard b y default on all th e PortFast ports, use the spanning-tree portfast bpduguard default co mmand . To return to the defau lt settings, use th e no form of this comman d. spanning-tree po rtfa st bpduguard default no spanning-tree portfast bpduguard default Syntax Description This comman d has no keywo rds or arg umen ts.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches spanning-tree portfast default spanning-tree portfast default To globally en able PortFast by default on all access ports, use the spanning-tree portfast defa ult command. To disable PortFast as default on all access ports, us e the no form of th is command. spanning-tree portfast default no spanning-tree portfast default Syntax Description This command has no arguments or keywo rds. Defaults PortFast is disab led.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches spanning-tree port-priority spanning-tree port-priority To prioritize an interface when two brid ges compete for po sition as the roo t bridge, u se the spanning-tree po rt-priority comman d. The priority y ou set resolves the conflict. To revert to the default setting , use the no form of this comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches spanning-tree uplinkfast spanning-tree uplinkfast To en able the UplinkFas t feature, use th e spanning-tree uplinkfa st comman d. To disab le Up lin kFast, u se the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches spanning-tree uplinkfa st Co mmand Description spanning-tree portfast (interface configuration mode) spanning-tree vlan Enables PortFast mode. Config ures STP on a per-VLAN basis . Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches spanning-tree vlan spanning-tree vlan To con figure STP o n a p er-VLAN basis, use the spanning-tree vlan co mmand . To return to th e default value, use the no fo rm of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches span ning-tree vlan The spa nning-tree root secondary command alters th e switch bridge p riority to 16384 . If the root switch fails, this switch becomes the nex t root switch. Use the spanning -tree root commands on back bone s witches on ly.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches speed speed To configure the interface speed, u se the speed comman d. To disable a speed setting, use th e no form of th is command. speed {10 | 100 | 100 0 | a uto [1 0 | 1 00 | 1000] | nonegotiate} no speed Syntax Description 10 1 00 Config ures the interface to transmit at 10 Mbps . Config ures the interface to transmit at 100 Mbp s. 1 000 a uto 10 | 100 | 1000 Config ures the interface to transmit at 1000 Mb ps.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches speed Table 2-35 Supported speed Command Options (continued) Interface Type Su pported Syntax Default Se tting Guidelines 10/10 0/1000 speed [10 | 100 | 1000 | auto] auto If th e speed is set to 10 or 100 and you do no t configure the d uplex settin g, the duplex is s et to half. 1000 Not applicab le. No t applicable. If the sp eed is set to 1 000 or auto with any su bset containing 10 00 (e.g.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches speed This example s hows how to allow Fast Ethern et interface 5/4 to autonegotiate the speed and duplex mo de: Switch(config)# interface fastethernet 5/4 Switch(config-if)# speed auto Note The speed auto 10 10 0 command is similar to the speed auto comman d on a Fast Ethernet interface.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches storm-control storm-control To en able broadcast storm con trol on a po rt and to specify what to d o wh en a storm occurs on a port, use the storm-co ntro l interface con figuratio n command. To disable storm control for th e broad cast traffic an d to d isable a specified s torm-co ntro l actio n, use the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches storm-control • Use the no form of this command. The lower level is ignored for th e interfaces th at perform storm co ntrol in the h ardware. Examples This example s hows how to enab le broadcast storm control on a port with a 75 .6 7 p ercent ris ing su ppressio n level: Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches storm-control broa dcast include multica st storm-control broadcast include multicast To enable multicast sto rm co ntrol on a port, use th e storm-control broadcast include multicast co mmand . To d isable multicast storm control, use the no form of this command. sto rm-control broadcast include multicast no storm-contro l broadca st include multica st Syntax Description This comman d has no argu ments or keyword s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches subscribe-to-alert-group all subscribe-to-alert-group all To subscrib e to all available alert gro ups, use the subscribe-to-alert-g roup a ll command. subscribe-to-a lert-group all Syntax Description This command has no arguments or keywo rds. Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches subscribe-to-alert-group configuration subscribe-to-alert-group configuration To sub scribe a destinatio n p rofile to the Con figuration alert group, use th e subscribe-to-alert-g roup configuration command. subscribe-to-alert-g roup configuration [periodic {daily hh:mm | monthly date hh:mm | weekly day h h:mm}] Syntax Description Defaults periodic (Optional) Specifies a p eriodic call-ho me mes sage.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches subscribe-to-alert-group configuration Command Descriptio n subscribe-to-a lert-group invento ry Sub scribes th is destination profile to th e Inventory alert g roup . Sub scribes this destination profile to th e Syslo g alert gro up. subscribe-to-a lert-group syslo g Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches subscribe-to-alert-group diagnostic subscribe-to-alert-group diagnostic To sub scribe a destinatio n p rofile to the Diag nostic alert group, use the subscribe-to-alert-g roup diagnostic co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches subscribe-to-alert-group diagnostic Command Descriptio n subscribe-to-a lert-group all Sub scribes to all available alert groups . subscribe-to-a lert-group configura tion Sub scribes th is destination profile to th e Configuration alert group. subscribe-to-a lert-group environment Sub scribes this d estin ation profile to th e Enviro nmen t alert g roup .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches subscribe-to-alert-group environment subscribe-to-alert-group environment To sub scribe a destinatio n p rofile to the Environ ment alert grou p, us e the subscribe-to-alert-g roup env ironment command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches subscribe-to-alert-group environment Command Descriptio n destination transport-method Enab les the message transport metho d. subscribe-to-a lert-group all Sub scribes to all available alert groups . subscribe-to-a lert-group configura tion Sub scribes th is destination profile to th e Configuration alert group. subscribe-to-a lert-group diagnostic Sub scribes th is destination profile to th e Diagno stic alert g roup .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches subscribe-to-alert-group inventory subscribe-to-alert-group inventory To sub scribe a destinatio n p rofile to the Inven tory alert gro up, u se the subscribe-to-alert-g roup inventory command. subscribe-to-alert-g roup inventory [periodic { daily hh :mm | monthly da te hh:mm | weekly day hh:mm}] Syntax Description Defaults periodic daily hh:mm (Optional) Specifies a p eriodic call-ho me mes sage.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches subscribe-to-alert-group inventory Command Descriptio n subscribe-to-a lert-group environment Sub scribes this d estin ation profile to th e Enviro nmen t alert g roup . Sub scribes this destination profile to th e Syslo g alert gro up. subscribe-to-a lert-group syslo g Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches subscribe-to-alert-group syslog subscribe-to-alert-group syslog To sub scribe th is d estination profile to th e Syslog alert gro up, u se the subscribe-to-alert-g roup s yslog comman d.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches subscribe-to-alert-group syslog Command Descriptio n destination preferred-msg-format destination transport-method profile Con figures a preferred mess age format. Enab les the message transport metho d. Enters profile call-home co nfigu ration submod e subscribe-to-a lert-group all Sub scribes to all available alert groups .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches switchport switchport To modify th e switching characteristics of a Layer 2 switch interface, use the switchport command. To return the interface to the routed-interface status and cause all further Layer 2 co nfigu ration to b e erased, use th e no form o f this co mmand without parameters.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches switchport If you use the switch port voice vlan comman d for an interface, the interface can not join a port chan nel. When you use the s witchport voice vlan command, th e output for the show running-config comman d changes to show the vo ice VLAN set.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches switchpo rt access vlan switchport access vlan To set the VLAN when an interface is in access mo de, use the switchport access vla n command. To reset the access mod e VLAN to the app rop riate default VLAN for the dev ice, us e the no form of th is co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches switchport access vlan Related Commands Command show interfa ces switchport Descriptio n Displays the administrative an d operational s tatus of a switch ing (no nro uting) p ort. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches switchport autostate exclude switchport autostate exclude To exclu de a port from the VLAN interface link -up calculation, use the switchport auto state exclude co mmand . To return to the defau lt settings, use th e no form of this comman d. switchport auto state exclude no switchport autostate exclude Syntax Description This comman d has no keywo rds or arg umen ts.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches switchport block switchport block To prevent th e unk nown multicast or unicast pack ets from being forwarded , use the switchport block in terface co nfiguration command. To allow the u nknown mu lticast or unicast p ackets to b e fo rwarded , u se the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches switchport mode switchport mode To set the interface ty pe, use th e switchport mode comman d. To reset the mode to the ap pro priate default mode for the device, u se the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches switchport mode The po rt becomes inactive if you configu re it as a private VLAN trunk p ort and one o f the followin g applies: • The po rt does not have a valid PVLAN association. • The po rt does not have valid allowed normal VLANs. If a private port PVLAN association or mapp ing is deleted , or if a private port is config ured as a SPAN d estination, it b ecomes inactive.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches switchport mode Administrative Private VLAN Host Association:none Administrative Private VLAN Promiscuous Mapping:200 (VLAN0200) 2 (VLAN0002) Private VLAN Trunk Native VLAN:none Administrative Private VLAN Trunk Encapsulation:dot1q Administrative Private VLAN Trunk Normal VLANs:none Administrative Private VLAN Trunk Private VLANs:none Operational Private VLANs: 200 (VLAN0200) 2 (VLAN0002) Trunking VLANs Enabled:ALL Pruning VLANs Enabled:2-
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches switchport mode Trunking Native Mode VLAN: 1 (default) Administrative Native VLAN tagging: enabled Voice VLAN: none Administrative private-vlan host-association: none A dministrative private-vlan mapping: none Administrative private-vlan trunk native VLAN: 10 Administrative private-vlan trunk Native VLAN tagging: enabled Administrative private-vlan trunk encapsulation: dot1q Administrative private-vlan trunk normal VLANs: none Administra
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches switchport mode Switch(config-if)# Related Commands switchport Description Displays the admin istrative and operation al status o f a switching (nonrouting ) port. Enables p ort secu rity on an interface. switchport private-vlan host-association Co mmand show interfaces switchport Defines a PVLAN association for an isolated or community port. switchport private-vlan mapping Defines private VLAN mapping for a promiscuous port.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches switchport port-security switchport port-security To en able port security on an interface, use the switchport port-security command. To disable po rt security and set p arameters to their default states, u se the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches switchport port-sec urity Defaults shutdown (Optional) Sets th e security violation shutd own mode. In this mode, a port security violation causes the interface to immediately become error disabled. shutdown vlan (Optional) Set the security violation mode to p er-VLAN sh utdown . In this mode, on ly th e VLAN on which th e violation occurred is error-disabled . The defau lt settings are as follows: • Port security is disabled .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches switchport port-security To allow limited time access to p articu lar secure ad dresses, set the aging typ e as abso lute. When the aging time lapses, the secu re add resses are deleted. To allow continuo us acces s to a limited nu mber of secure add resses , set the ag ing type as inactivity. This action removes th e secure addres s when it becomes inactive, and oth er addresses can b ecome secure.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches switchport port-sec urity Switch(config-if)# switchport port-security mac-address 1000.2000.3000 Switch(config-if) This examp le shows how to make all MAC addresses learned on Fast Ethern et port 12 sticky : Switch(config)# interface fastethernet 2/12 SSwitch(config-if)# switchport port-security mac-address sticky Switch(config-if) This examp le shows how to make M AC address 10 00.2000.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches switchport port-security Note Sending traffic to the ports causes th e system to configure the p ort with sticky secu re addresses . You can verify your settings by usin g th e show port-security address privileged EXEC comman d. Related Commands Command Descriptio n show interfa ces switchport Displays the administrative an d operational s tatus of a switch ing (no nro uting) p ort.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches switchport private-vlan association trunk switchport private-vlan association trunk To configure the association between a secondary VLAN and a VLAN on a private VLAN trunk port, u se the switchpo rt private-vlan associatio n trunk command. To remove the private VLAN mapping from the port, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches switchport private-vlan association trunk Switch# show interfaces fastethernet 5/2 switchport Name: Fa5/2 Switchport: Enabled Administrative Mode: private-vlan trunk secondary Operational Mode: private-vlan trunk secondary Administrative Trunking Encapsulation: negotiate Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Administrative Native VLAN tag
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches switchport private-vlan host-association switchport private-vlan host-association To d efine a PVLAN association for an isolated or community port, use the switchpo rt private-vlan host-association command. To remove the PVLAN mapping from the port, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches switchport private-vlan host-association Negotiation of Trunking: Off Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Voice VLAN: none Appliance trust: none Administrative Private Vlan Host Association: 202 (VLAN0202) 440 (VLAN0440) Promiscuous Mapping: none Trunk encapsulation : dot1q Trunk vlans: Operational private-vlan(s): 202 (VLAN0202) 440 (VLAN0440) Trunking VLANs Enabled: ALL Pruning VLANs Enabled: 2-1001 Cap
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches switchport private-vlan mapping switchport private-vlan mapping To d efine private VLAN mapping for a promiscuous port, use the switchport priva te-vla n mapping co mmand . To clear all mapping from the primary VLAN, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches switchport private-vlan mapping This example s hows how to add a rang e of secondary VLANs to the mapping : Switch(config-if)# switchport private-vlan mapping 18 add 22-24 Switch(config-if)# This example s hows how to add a rang e of secondary VLANs to the trunk mapping: Switch(config-if)# switchport private-vlan mapping trunk 18 add 22-24 Switch(config-if)# This example shows how to configu re in terface FastEthern et 5/2 as a PVLAN p
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches switchport private-vlan mapping Administrative private-vlan host-association: none Administrative private-vlan mapping: none Administrative private-vlan trunk native VLAN: 10 Administrative private-vlan trunk Native VLAN tagging: enabled Administrative private-vlan trunk encapsulation: dot1q Administrative private-vlan trunk normal VLANs: 3-4,10 Administrative private-vlan trunk associations: none Administrative private-vlan trunk mappings
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches switchport private-vlan trunk allowed vlan switchport private-vlan trunk allowed vlan To configure a list of the allowed normal VLANs on a private VLAN trunk port, u se the switchport private-vlan trunk allowed v lan command. To remove all the allowed normal VLANs from a private VLAN trunk port, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches switchport private-vlan trunk allowed vlan This examp le shows how to configure interface FastEthern et 5/2 as a second ary trun k p ort, an d v erify the configuration : Switch# configure terminal Switch(config)# interface fastethernet 5/2 Switch(config-if)# switchport mode private-vlan trunk secondary Switch(config-if)# switchport private-vlan trunk native vlan 10 Switch(config-if)# switchport private-vlan trunk allowed vlan 10.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches switchport private-vlan trunk allowed vlan Administrative private-vlan host-association: none Administrative private-vlan mapping: none Administrative private-vlan trunk native VLAN: 10 Administrative private-vlan trunk Native VLAN tagging: enabled Administrative private-vlan trunk encapsulation: dot1q Administrative private-vlan trunk normal VLANs: 3-4,10 Administrative private-vlan trunk associations: none Administrative private-vlan t
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches switchport private-vla n trunk native vlan tag switchport private-vlan trunk native vlan tag To control th e tagging of th e native VLAN traffic on 802 .1Q p rivate VLAN trunks, use the switchport private-vlan trunk native vlan tag command. To remove the control of tagging (and default to the global setting), use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches switchport trunk switchport trunk To set the trun k characteristics when an interface is in trunking mod e, use the switchport trunk command. To reset all of the trunk ing ch aracteristics back to the o riginal defaults, u se the no form of th is command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches switchpo rt trunk • ex cept lists the VLANs th at shou ld be calculated by inverting the defined list o f VLANs. • vla n_atom is either a sing le VLAN nu mber from 1 to 4 094 or a con tinuous ran ge of VLANs described by two VLAN numbers (the lesser on e first, separated by a hyphen). The no form of the na tive vlan comman d resets the native mode VLAN to the appropriate default VLAN for the device.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches switchport trunk Examples • The no option is saved to NVRAM so that th e user does not have to man ually select the ports to d isable the tagging o peration each time that the switch reboots. • When the switchport trunk native vlan tag co mmand is enabled and active, all p ackets o n th e n ative VLAN are tagged, and incoming untagged data packets are dro pped. Untag ged control p ackets are accep ted.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches switch port vlan mapping switchport vlan mapping Use the switchport vlan mapping interface configuration command to configure VLAN mapping on a trunk port. You can configure one-to-one VLAN mapping, traditional IEEE 802.1Q tunneling (QinQ) mapping, or selective QinQ mapping. Use the no form of the command to disable the configuration.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches switchport vlan mapping The no form of the switchport vlan mapping commands clears th e specified mappin g configuration . The no switchport vlan ma pping all command clears all mapp ing co nfigurations on the in terface. You cannot configure encap sulatio n replicate o n a SPAN d estination port if th e so urce port is config ured as a tunn el port or has a 1-to-2 mapping configured.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches system mtu system mtu To set the maximum Layer 2 or Layer 3 payload size, u se the system mtu co mmand . To revert to the default MTU setting, u se the no form of this command. system mtu datag ram-size no sy stem mtu Syntax Description datagra m-s ize Defaults The defau lt MTU setting is 1 500 bytes. Command Modes Usage Guidelines Layer 2 pay load size; valid valu es from 150 0 to 1 552 bytes.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches test cable-diagnostics tdr test cable-diagnostics tdr To test the con dition of copp er cables on 4 8-p ort 10/10 0/1000 BASE-T modules, use the test cable-diagnostics tdr command. test cable-diagnostics tdr { interfa ce {in terfa ce interfa ce-n umber} Note This command will be deprecated in future Cisco IOS releases. Use the diagnostic start command in stead.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches test cable-diagnostics tdr diag tdr test is not supported on this module Switch# Note Related Commands The sho w cable-diagnos tic tdr comman d is us ed to display the results of a TDR test. The test results will not be available until app rox imately 1 min ute after the test starts. If you en ter th e show cable-diagnostic tdr command within 1 minute of the test starting , you may see a “TDR test is in pro gress on interface...
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches traceroute mac traceroute mac To d is play the Layer 2 path taken by th e packets from the specified source MAC addres s to th e s pecified d estination MAC ad dress, use the traceroute mac command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches tra ceroute mac Examples This examp le shows how to d isplay th e Layer 2 path b y s pecify ing the so urce and destination MAC ad dresses: Switch# traceroute mac 0000.0201.0601 0000.0201.0201 Source 0000.0201.0601 found on con6[WS-C2950G-24-EI] (2.2.6.6) con6 (2.2.6.6) :Fa0/1 =>Fa0/3 con5 (2.2.5.5 ) : Fa0/3 =>Gi0/1 con1 (2.2.1.1 ) : Gi0/1 =>Gi0/2 con2 (2.2.2.2 ) : Gi0/2 =>Fa0/1 Destination 0000.0201.0201 found on con2[WS-C3550-24] (2.2.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches traceroute mac This example s hows the Lay er 2 path wh en the source and d estination switches belong to multiple VLANs: Switch# traceroute mac 0000.0201.0601 0000.0201.0201 Error:Mac found on multiple vlans. Layer2 trace aborted. Switch# This example s hows how to display the Lay er 2 p ath by specifying th e interfaces o n th e source and d estination switches: Switch# traceroute mac interface fastethernet0/1 0000.0201.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches traceroute mac ip traceroute mac ip To display the Layer 2 path that is taken by the packets from th e sp ecified so urce IP address or hostname to the specified destin ation IP addres s o r hostname, use the traceroute mac command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches traceroute mac ip Switch# traceroute mac ip 2.2.66.66 2.2.22.22 detail Translating IP to mac..... 2.2.66.66 =>0000.0201.0601 2.2.22.22 =>0000.0201.0201 Source 0000.0201.0601 found on con6[WS-C2950G-24-EI] (2.2.6.6) con6 / WS-C2950G-24-EI / 2.2.6.6 : Fa0/1 [auto, auto] =>Fa0/3 [auto, auto] con5 / WS-C2950G-24-EI / 2.2.5.5 : Fa0/3 [auto, auto] =>Gi0/1 [auto, auto] con1 / WS-C3550-12G / 2.2.1.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches tru st trust To define a trust state for traffic clas sified through the clas s policy-map configuration comman d, use the trust policy-map class configu ration co mmand . To retu rn to the default settin g, use the no form of this co mmand . trust [cos | dscp] no trust [cos | ds cp] Syntax Description co s dscp (Optional) Clas sifies an ingress packet by u sing the packet class of serv ice (CoS) valu e.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches trust You can verify your settings by entering the show policy -map privileg ed EXEC command. Related Commands Command Descriptio n class Specifies the name of th e class wh ose traffic p olicy you want to create or change. police policy-map Con figures the Traffic Policin g feature. Creates a policy map that can be attached to multiple po rts to sp ecify a service policy an d to enter policy-map config uration mo de.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches tx-queue tx-queue To con figure the transmit queue parameters for an in terface, use the tx-queue co mmand . To retu rn to the default value, us e the no form of th is command. tx-queue [queue-id ] {bandwidth ban dwidth-ra te | priority high | shape shap e-rate} no tx-queue Syntax Description queue-id bandwidth ba ndwidth-rate priority high shape shap e-rate (Optional) Nu mber of the queue; valid values are from 1 to 4.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches tx-queue This example s hows how to configure the traffic shaping rate o f 64 kbp s to tran smit q ueu e 1: Switch(config-if)# tx-queue 1 Switch(config-if-tx-queue)# shape 64000 Switch(config-if-tx-queue)# Related Commands Command Descriptio n show qos interface Displays queuein g information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches udld (global configuration mode) udld (global configuration mode) To en ab le aggressive or normal mode in the UDLD protocol and to set the configurable message timer time, use th e udld global co nfiguration command. You can also use this command to set the error reporting mode for Fast UDLD.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches udld (global configuration mode) Usage Guidelines If you enable aggressiv e mode, on ce all the s witch p ort’s neighb ors have aged o ut either in the advertisement or in the d etectio n phase, UDLD and Fast UDLD restart the lin kup sequence. They can resynchro nize with any potentially o ut-of-sync neighb or an d sh ut down th e port if the UDLD messages fro m the neighbor indicate that the link state is still und etermin ed.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches udld (interface configuration mode) udld (interface configuration mode) To enable UDLD and Fast UDLD o n an individu al interface o r to preven t a fiber-optic in terface from being enabled by the udld (glob al configuration mode) command, use the udld interface level command. Use th e no form o f this command to disable UDLD, or to retu rn a no nfiber port to th e settin g s pecified with the udld (g lobal configuration mod e) command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches udld (interface configuration mode) Examples This ex ample shows how to enable UDLD o n any port interface for any global udld (global config uration mo de) setting : Switch (config-if)# udld port Switch (config-if)# This example shows how to enable UDLD in aggressive mode on any port interface for any glob al udld (enable or agg ressive) settin g: Switch (config-if)# udld port aggressive Switch (config-if)# This example s hows how to
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches udld reset udld reset To reset all the UDLD ports in th e shutd own state (that is, errdisabled by UDLD), use the udld reset priviledged EXEC command. udld reset Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches unidirectional unidirectional To co nfigure th e nonb lock ing Gigabit Ethern et ports to u nidirectionally sen d o r receive traffic on an in terface, u se the unidirectional co mmand . To d isab le unidirection al communication , use the no form o f this co mmand .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches userna me username To estab lish a usern ame-b ased au then tication system, u se the userna me command. username name secret { 0 | 5} pas swo rd Syntax Description name User ID of the user. secret 0 | 5 Specifies the authentication sy stem for the u ser; valid values are 0 (text immed iately following is not encrypted) and 5 (text immediately followin g is en crypted using an MD5-type encry ption method). Passwo rd of the user.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches verify verify To verify th e checksum of a file on a flash memory file system, us e the v erify command. verify [/md5] [flash-filesystem:] [filename] [expected-md5 -sign ature] Syntax Description filename (Optio nal) Verifies the MD5 signatures. (Optio nal) Dev ice where the fash res ides; valid values are bootflash:, slo t0:, flash:, or sup-bootfla sh:. (Optio nal) Name of th e Cisco IOS imag e.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches verify To disp lay the con tents of the flash memory, enter the sho w flas h comman d. Th e flash contents listing does not in clud e th e check sum of the individual files. To recompute and verify the image checksum after the image h as been copied into the flash memory, enter the verify comman d. A colon (:) is req uired after the sp ecified dev ice.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches vlan (VLAN Database mode) vlan (VLAN Database mode) To co nfigure a specific VLAN, use th e vlan co mmand . To d elete a VLAN, u se the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches vlan (VLAN Database mode) Defaults The defau lts are as follows: • • • The vlan -name is “VLANxx xx” where “xx xx” rep resen ts four numeric d igits (including leading zeroes) eq ual to the VLAN ID n umber. The media type is Fas t Eth ernet. The state is active. • The said-value is 100,00 0 p lus the VLAN ID numb er.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches vlan (VLAN Database mode) Note If the VLAN already exists, no action occu rs.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches vlan a ccess-map vlan access-map To enter VLAN access-map co mmand mo de to create a VLAN access map , use the vlan access-map co mmand . To remove a mapping sequence or the entire map , use the no fo rm of this command. vlan access-map name [seq# ] no v lan access -map na me [seq# ] Syntax Description name seq # VLAN access-map tag. (Option al) M ap sequence numb er; valid valu es are from 0 to 65 535.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches vlan configuration vlan configuration To co nfigure a service-policy on a VLAN, use the vla n configura tion co mmand to enter the VLAN feature configuration mod e. v lan configuratio n {vlan} Syntax Description vlan Defaults This command has no default setting s. Specifies a list of VLANs. “,” “-” operators can be used; such as, 1-10,20.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches vlan configuration 0 packets police: rate 128000 bps, burst 4000 bytes conformed 0 packets, 0 bytes; action: transmit exceeded 0 packets, 0 bytes; action: drop conformed 0 bps, exceeded 0 bps Switch# Related Commands Co mmand vlan (VLAN Database mode) Description Config ures a specific VLAN.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches vlan database vlan database To en ter VLAN co nfiguration mode, use the vla n data ba se comman d. vlan database Syntax Description This command has no arguments or keywo rds. Defaults This command has no default setting s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches vlan database This examp le shows how to tu rn off pru ning after you are in VLAN co nfigu ration mode: Switch(vlan)# no vtp pruning Pruning switched OFF Switch(vlan)# Related Commands Co mmand show vlan Description Displays VLAN information . Catalyst 4500 Series Switch Cisco IOS Command Reference—Re lease IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches vlan dot1q tag native vlan dot1q tag native To enable taggin g o f the native VLAN frames on all 80 2.1 Q trun k p orts, use the v lan dot1q tag na tive command. To disable tagging of native VLAN frames, use the no form o f this co mmand . v lan dot1q tag native no vlan dot1 q ta g na tive Syntax Description This command has no arguments or keywo rds. Defaults 8 02.1Q nativ e VLAN tagging is disabled.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches vlan filter vlan filter To apply a VLAN access map, us e the v lan filter comman d. To clear the VLAN access maps from VLANs or in terfaces, use the no form o f this co mmand . vlan filter map-name {vlan-list vla n-list } no vlan filter ma p-n ame { v lan-list [vlan-list ]} Syntax Description map -name vlan-list vlan -list VLAN acces s-map tag. Sp ecifies th e VLAN list; see the “Usage Guidelines” sectio n for valid values.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches vlan group vlan group To create o r mod ify a VLAN group, us e th e v la n group command in g lobal co nfigu ration mod e. Us e th e no form of th is command to remove a VLAN list from th e VLAN group . v lan group group -na me v lan-list vlan-list no vlan gro up group-name vlan-list vlan-lis t Syntax Description g rou p-n ame vlan-list Defaults This command has no arguments or keywo rds.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches vlan internal allocation policy vlan internal allocation policy To config ure the internal VLAN allocation scheme, use th e vlan internal allocatio n policy command. To return to the default setting, use the no form of this command. vlan internal allocation policy {ascending | descending } no v lan interna l allo cation po licy Syntax Description ascending descending Specifies to allocate in ternal VLANs from 1 006 to 4094 .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches vmps reconfirm (global configuration) vmps reconfirm (global configuration) To ch ang e the recon firmation interval for the VLAN Query Pro toco l (VQP) client, u se the vmps reconfirm command. To return to th e default settin g, use the no form of this command.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches vmps reconfirm (privileged EXEC) vmps reconfirm (privileged EXEC) To immediately send VLAN Query Protocol (VQP) qu eries to reconfirm all the dynamic VLAN ass ignments with the VLAN Membership Policy Server (VMPS), u se the v mps reco nfirm command. vmps reconfirm Syntax Description This comman d has no argu ments or keyword s. Defaults This comman d has no default settings.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches vmps retry vmps retry To configure the per-server retry count for the VLAN Query Protocol (VQP) client, use the v mps retry command. To return to the default setting, u se the no form of th is command. v mps retry co unt no vmps retry Syntax Description coun t Numb er o f attempts to contact the VLAN Membership Policy Server (VMPS) by the client before qu erying the nex t server in the list; valid valu es are from 1 to 10 .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches vmps server vmps server To configu re the p rimary VLAN Membership Policy Server (VM PS) and u p to three secondary servers, use th e vmps serv er command. To remove a VM PS server, use the no form of this command. vmps server ip addres s [primary] no vmps server ipad dress Syntax Description ipadd ress primary Defaults Command Modes Usage Guidelines IP address or host name of th e primary or seco ndary VM PS servers.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches vmps server Related Commands Command show v mps Descriptio n Displays the VLAN Query Pro toco l (VQP) version, recon firmation interval, retry count, VLAN Memb ership Policy Server (VMPS) IP addresses, current servers, an d primary servers. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches vtp (global configuration mode) vtp (global configuration mode) To modify th e name of a VTP co nfiguration s torage file, us e the vtp co mmand . To clear a filename, u se the no fo rm of this command. vtp {{file filename} | {if-id n ame}} no vtp {{file filename} | {if-id name}} Syntax Description file filename if-id na me Defaults Disabled Specifies the IFS file wh ere VTP configuration will b e stored .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches vtp client vtp client To place a dev ice in VTP client mo de, use th e vtp client command. To return to VTP server mo de, use th e no form o f this co mmand . vtp client no vtp client Syntax Description This command has no arguments or keywo rds.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches vtp domain vtp domain To config ure the administrative domain n ame for a dev ice, us e the v tp do main co mmand . vtp domain domain-name Syntax Description domain-n ame Defaults This comman d has no default settings. Command Modes Usage Guidelines Name of the domain. VLAN config uration mode Wh en y ou define the d omain -na me, the domain name is case sensitive and can be from 1 to 32 characters.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches vtp password vtp password To create a VTP domain pas sword, use th e vtp pa ssword comman d. To delete the password, u se the no form of this command. vtp pas sword pa ssword-value no vtp password Syntax Description pas swo rd -value An ASCII strin g, from 1 to 32 characters, identifying the administrative domain for th e dev ice.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches vtp pruning vtp pruning To enable pruning in the VLAN datab ase, u se the vtp pruning command. To disable prunin g in the VLAN datab ase, u se the no form of this command. vtp pruning no vtp pruning Syntax Description This comman d has no argu ments or keyword s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches vtp server vtp server To place the device in VTP server mode, u se the vtp server comman d. v tp server Syntax Description This command has no arguments or keywo rds. Defaults Enabled Command Modes VLAN con figuratio n mode Usage Guidelines If you make a ch ang e to the VTP or VLAN configuration on a switch in s erver mode, that change is p ropagated to all the switches in the same VTP d omain .
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches vtp transparent vtp transparent To place a device in VTP transparent mode, use the vtp transparent command. To return to VTP server mode, use the no fo rm of this command. vtp transparent no v tp transparent Syntax Description This comman d has no argu ments or keyword s.
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Serie s Switches vtp v2-mode vtp v2-mode To en able version 2 mode, use the vtp v2-mode co mmand . To disable version 2 mode, use th e no form o f this co mmand . vtp v2-mode no vtp v2 -mode Syntax Description This command has no arguments or keywo rds. Defaults Disabled Command Modes VLAN con figuratio n mode Usage Guidelines All switch es in a VTP domain must run the same version of VTP.
A P P E N D I X A Abbreviations A ACE ACL AFI access co ntro l entry access co ntro l list autho rity and format identifier Agport aggreg ation po rt AMP Active Monitor Present APaRT Automated Packet Recognition and Translation ARP Address Resolution Protocol B BEM BGP best effort method Border Gateway Protocol BPDU b ridge protocol d ata unit BRF b ridge relay function BSC BSTUN Bisy nc Block Serial Tunn el BUS b roadcas t and unk nown server BVI b ridge-gro up virtu al interface C
Appendix A Abbreviations C CAM content-addressab le memo ry CAR committed access rate CCA CDP circuit card assembly Cisco Discovery Protocol CEF Cisco Express Forwarding CHAP Challeng e Hands hake Auth entication Protocol CIR CLI CLNS CMNS committed information rate comman d-line interface Connection-Less Network Serv ice Connection-Mode Network Serv ice COPS Common Open Policy Serv er COPS-DS Common Open Policy Serv er Differentiated Services CoS class of service CPLD Complex Programma
Appendix A DEC DFI Abbreviations Digital Equipment Co rpo ration Domain-Specific Part Format Identifier DFP Dynamic Feedb ack Protocol DISL Dynamic Inter-Switch Link DLC DLSw DMP DNS DoD DOS DRAM Data Link Control Data Link Switching d ata movement pro cessor Domain Name System Dep artmen t of Defense d enial of serv ice dynamic RAM DRiP Dual Ring Protocol DSAP d estination serv ice access poin t DSCP d ifferentiated s ervices code p oint DSPU d ownstream SNA Ph ysical Units DTP Dynamic T
Appendix A EIA Electronic Ind ustries Asso ciation ELAN Emulated Local Area Netwo rk EOBC Ethernet ou t-of-b and channel ESI end-system identifier Abbreviations F FECN FM forward exp licit co ngestion notification feature man ager FRU field replaceable un it FSM feasible su ccessor metrics G GARP GMRP GVRP General Attribute Reg istration Proto col GARP Multicast Registration Pro tocol GARP VLAN Registration Pro tocol I ICC Inter-card Communication ICD International Cod e Designator ICM
Appendix A Abbreviations ILMI Integrated Local Manag ement In terface IP Internet Protocol IPC in terpro cessor commun ication IPX Internetwo rk Packet Exch ang e IS-IS Intermediate System-to-In termed iate Sys tem In tradomain Ro uting Proto col ISL Inter-Switch Link ISO International Organ ization of Standardization ISR Integrated SONET router ISSU In Service Software Upgrade L L2 L3 L4 Lay er 2 Lay er 3 Lay er 4 LAN lo cal area network LANE LAN Emulation LAPB Link Access Proced
Appendix A Abbreviations M MAC MCL MD5 Media Access Con trol Mismatch ed Command List Message Dig est 5 MET Multicas t Expansion Table MFIB Multicas t Forwarding Information Bas e MIB Management In formatio n Base MII media-independent interface MLS MLSE MOP MOTD MRM Multilayer Switching mainten ance lo op signaling en tity Maintenan ce Operation Proto col messag e-of-the-d ay multicast routing monito r MRQ Multicas t Replication Queu e MSDP Multicas t Source Discovery Pro toco l MST Mult
Appendix A NMP NSAP NTP NVRAM Abbreviations Network Managemen t Processor n etwork serv ice access poin t Network Time Protocol n onvolatile RAM O OAM Operation, Administratio n, and Maintenan ce OSI Open Sys tem In terco nnection OSPF o pen sh ortest path first P PAE p ort access entity PAg P Port Aggreg ation Pro tocol PBD PC PCM PCR PDP p acket buffer daugh terboard Perso nal Compu ter (fo rmerly PCMCIA) p ulse code modulation p eak cell rate p olicy decision point PDU p rotocol data un
Appendix A PPP Abbreviations Point-to-Point Pro toco l PRC Parser Return Code PRID Policy Rule Identifiers PVLAN Private VLAN PVST+ Per VLAN Spanning Tree+ Q QM QoS Qo S manager Qu ality of Serv ice R RACL RADIUS RAM RCP RGMP RIF Router Interface Access Control List Remo te Access Dial-In User Serv ice rand om-access memory Remo te Copy Pro to co l Router Group Managemen t Pro tocol Routing Information Field RMON Rmote Network Monitor ROM read-only memo ry RP route proces sor or rendezv
Appendix A RSVP Rx Abbreviations ReSerVation Protocol Receive S SAID Secu rity As sociation Iden tifier SAP service access po int SCM service co nnection manager SCP SDLC SGBP SIM M SLB SLCP SLIP Switch-Modu le Config uration Pro toco l Syn chronou s Data Link Control Stack Grou p Bid ding Protocol sin gle in-line memory module server load balancing Sup ervisor Line-Card Processor Serial Line Internet Protocol SMDS Software Man agement and Delivery Systems SMF so ftware MAC filter SMP Stand
Appendix A SVC switched virtual circuit SVI switched virtual interface Abbreviations T TACACS+ Terminal Access Con troller Access Con trol System Plus TARP Targ et Iden tifier Address Resolutio n Protocol TCAM Ternary Content Add ressable Memory TCL TCP/IP TFTP TIA TLV Top N TOS table contention level Transmiss ion Co ntro l Protocol/Internet Pro toco l Trivial File Transfer Protocol Teleco mmunication s Indu stry As sociation type-leng th-value Utility that allows th e user to analy ze port tr
Appendix A Abbreviations V VACL VLAN access control lis t VCC v irtual channel circuit VCD v irtual circu it descripto r VCI VCR VINES VLAN VMPS VTP VVID v irtual circu it identifier Virtual Configuration Register Virtual Network System v irtual LAN VLAN Membership Policy Server VLAN Trun king Protocol voice VLAN ID W WFQ weig hted fair queuein g WRED weig hted ran dom early d etectio n WRR weig hted round -robin X XNS Xerox Netwo rk System Ca talyst 4500 Series Switch Cisco IOS Comma nd R
Appendix A Abbreviations Catalyst 4500 Series Switch Cisco IOS Command Reference—Release IOS XE 3.3.0XO(15.
IN DEX enab ling sen d s uccess packets Symbols enab ling on a po rt $ matches the end of a strin g ( ) in commands 1-7 1-7 setting delay time o n a port 2- 180 2-181 2-181 802 .1X critical auth entication 1-7 configure parameters 1-1 2-22 802 .1X critical reco very delay , config urin g 2-22 ? matches 0 or 1 occurrence of a pattern ^ matches the beginn in g of a string 1 -7 802 .1X Po rt Based Auth entication 1-7 debugg ing 802.
Index displaying mac interface show mo de interface altern ation 2-67 1 description 2-44 0, 2-513, 2- 741 access groups IP 1-10 an cho ring description 2 -6, 2-172 access lists 1-10 an cp, show mu lticast clearing an access template defining ARP 2-51 6 ANCP client 2-94 2-18 displaying ARP information 2-517 See also ACLs, MAC ACLs, and VACLs port identifier 2-1 4 remote server 2- 15 set router to become access maps 2- 16 ARP ap plying with VLAN filter access list, displaying det
Index authentication methods , specifying the order of attemp ts 2-29 authentication op en command authentication timer, settin g disp layin g d ebu gging messages disp layin g s pan ning tree status 2 -28 authentication order comman d enabling debuggin g 2-2 9 authentication periodic command bandwidth co mmand 2-30 authentication po rt-co ntrol command authentication priority command store for DHCP sn ooping 2-244 BOOT en viro nmen t variable disp layin g in formatio n 2-52 7 2-3 5 boo tfla
Index neighbor information set drop thresh old for clearing MFIB counters and routes 2- 535 en ablin g p roto col tunn eling for clearing MFIB fastd rop entries 2-312 clearing QoS aggreg ate cou nters displaying next-hop information clearing VLAN in terfaces 2-601 displaying VLAN configuratio n in formatio n 2-6 01 ch assis clear ip wccp command 2-669 ex pressions multipliers 1-7 1-6 multiple-character patterns cisco-desktop parentheses for recall using cisco-phon e co mmand macro
Index po licy map to control plane enabling debuggin g messages for ISL VLAN IDs 2-160 2-493 disp layin g po licy-map class in formatio n entering configuration mo de enabling debuggin g messages for VTP 2-7 16 2- 161 enabling debuggin g o f UDLD activ ity 2-119 enabling switch shim debuggin g removing serv ice policy fro m control plane 2-493 assignin g to Layer 2 protocol packets 2-313 2-162 2-154 enabling VLAN manager file system error tests limiting debugg ing output for VLANs CoS coun
Index clearing bin ding entries clearing database en tering 2- 97 CoPP config uration mode 2-99 displaying bind ing tab le en ablin g DHCP globally pro tecting system’s reso urces 2-602 dro p th reshold, Layer 2 protocol tu nneling en able 2-253 selecting a connector co nfigu ring autonegotiation on an interface 2-243 2-198 co nfigu ring full duplex on an interface 2 -198 co nfigu ring half du plex o n an interface 2-198 dynamic ARP inspection preventing 2-244 diagnostic fpga soft-erro
Index enabling error disable d etectio n verifying check sum 2-9 0, 2-204 enabling per-VLAN on BPDU gu ard configuring a gigabit interface for pau se frames disp layin g 2-58 6 disp layin g recov ery timer information enabling ARP inspection timeout specifyin g recov ery cause 2-2 06 2- 560 G 2-206 GBIC 2- 206 disp layin g SEEPROM info rmation assignin g in terfaces to EtherCh ann el groups debug ging EtherCh ann el debug ging PAgP shim 2-79 2 -567 generic-error-message, setting for the sw
Index displaying SEEPROM information ch assis en abling p er-VLAN Explicit Host Tracking en abling 2-567 displaying inline power status 2-730 In Service Software Upgrade 2-567 disabling globally 2-795 inline p ower 2-567 2- 567 power s upplies See ISSU 2-56 7 superv isor engine inspectio n lo g 2- 567 clearing log bu ffer clearing SNMP ifIndex comman ds 2-79 3 co mpress SNMP ifIndex table format 2-798 2-9 5 displaying supp ressed multicast bytes displaying 2-794 2-58 0 2-576 inte
Index configuring disp layin g configuratio n and filters 2- 913 default setting enabling on DHCP sno oping 2 -913 disp layin g allocation info rmation configuring queries applying ARP ACL to VLAN 2-95 2-2 37 enabling dynamic in spection counting sn ooping last-lis tener-queries disp layin g p orts for a switch o r VLAN disp layin g q uerier information 2-597 2-6 00 enabling snoop ing disabling 2-277 2-277 ip wccp command 2-284 2-281 ip wccp grou p-address command ip wccp grou p-list com
Index displaying session information displaying software version displaying state displaying information about an adjacency table 2-514 2-661 2-662 displaying port status 2-662 forcing switchover to standby su pervisor en gine 2-310 loading new imag e starting process 2-588 displaying status of native VLAN tagg ing 2 -588 link-status event messages disabling 2-306 globally 2-308 stoppin g rollback timer 2 -320, 2-323 on an interface 2-304 2 -321, 2-324 en abling globally J 2 -320, 2-32
Index MAC addres s table adding static entries adding a global d escrip tion cisco g lo bal 2-365 clearing dynamic entries configuring ag in g time system-cpp 2-108, 2-11 0 2 -364 2-362 2-363 mapping secondary VLANs to MST instance 2-330 2-457 disp layin g d ynamic table entry in formatio n 2-67 6 mapping VLAN(s) to an MST instance disp layin g entry co unt 2- 675 disp layin g in formatio n 2-6 72 match (class-map configuration ) command 2-13, 2-168, 2-169, 2-170, 2-17 1, 2-367, 2- 838, 2-
Index resetting a modu le by togg ling the po wer Multiple Spannin g Tree 2-214 monitor capture {access-list | class-map} co mmand monitor capture mycap match command filter search See MST 2-379 2-386 monitor capture start comman d 2-388 N --More-- prompt 1-6 nativ e VLAN 1-7 co ntrollin g taggin g of traffic MST 2-87 5 displaying ports eligib le for native tagging designating the primary and second ary roo t displaying MST protocol information 2-820 displaying spannin g tree information
Index bo otup, displaying results Policy Based Routing 2-546, 2- 548 on going, displaying resu lts See PBR 2-550 PACL policy maps access-g rou p mo de creatin g 2-6 paging prompt 2-4 21 markin g 2-49 7 see --More-- prompt See als o QoS, hierarch ical p olicies PAgP traffic classification clearing port channel in formatio n debug ging PAgP activity defin ing the clas s 2-11 2 defin ing trust states 2-143 deselecting chan nelin g proto col selecting the con nector 2-713 ho t standb
Index displaying settings fo r an in terface or switch set circuit-id o r remote-id for an interface 2-724 en ablin g 2-86 0 filter sou rce IP and MAC ad dresses displaying set trust con figuration on an interface 2-860 2-860 2-860 2-444 set circuit-id o r remote-id for an interface VLAN range 2-4 45 2- 278 settin g action upon security vio lation settin g th e rate limit for bad packets stick y port 2 -446, 2-447 PPPoE Intermediate Agent, display con figuration an d statistics (p acket coun t
Index attaching a policy-map to an interface automatic config uration setting QoS group identifiers 2 -488 2-39, 2-43, 2 -47, 2-51, 2-55, 2 -59, configuring for tunneled Layer 2 protocol packets 2-313 class maps creating quality of service 2- 87 defin ing the match criteria clearing agg regate counters configuring au to See QoS 2-367 question command 2-116 2-742 queue limiting configuring packet limits disp layin g class maps information 2 -524 R 2-7 19 2-715, 2-7 22 2- 741 disp layin g
Index synchronizing the route p rocessor co nfigu rations 2-365 related documentation server (AAA) alive actio ns, configuring server (AAA) dead actions, configuring 1 -xxii 2-44 4 sess ion classification, defining set the redund ancy mode shape command 2 -491 2-26 2- 377 2-376 2- 508 shell trigger comman d 2-51 1, 2-755 ip dhcp snoopin g d atabase 2-474 show ancp multicast 2 -475 2-516 show authentication in terface co mmand 2-476 rep lsl-age-timer command show authentication session s co
Index disp layin g in formatio n abo ut th e system sticky ad dress, con figu ring 2- 760 SNMP 2-15 1 clearing SNMP ifIn dex commands disabling glo bally 2-275 2-275 2-1 13 enabling security 2 -860 configuring for action when storm o ccurs disabling su ppression mod e 2-794 disp layin g s ettings disabling 2-795 enabling 2-795 enabling 2-835 2-8 35, 2-837 enabling multicast configuring to send when storm occu rs disabling 2-795 enabling 2-795 2-835, 2-83 7 enabling suppression mode
Index en ablin g extended system ID 2-808 T en ablin g lo op guard as a default on all po rts 2-811 en ablin g PortFast by default on all access ports en ablin g PortFast mode Tab key co mmand completion 1-1 tables 2-312 ch aracters with special meanin g 1-7 2-80 9 en ablin g s pan ning tree Back boneFast mac access-list extended subcommands 2-802 en ablin g s pan ning tree o n a per VLAN basis en ablin g s pan ning tree UplinkFast settin g an interface p riority settin g drop threshold for
Index setting format 2-876 V trunk interfaces disp layin g trunk interfaces information trunk port, configuring VLAN mapping VACLs 2-595 access-g roup mo de 2-879 trunk ports, d isplay VLAN mapp ing info rmation trust con figu ration, s etting on an interface 2 -784 2-446, 2-447 setting 2-6 applying VLAN access maps 2- 911 disp layin g VLAN access map info rmation 2- 779 specifyin g an action in a VLAN access map trust state disp layin g in formatio n abo ut Lay er 2 p rotocol 2-664 us
Index VLAN access map reco nfirming dyn amic VLAN ass ignments resetting voice VLANs en abling 2- 486 co nfigu ring auto-QoS 2-129 per-server retry coun t 2- 782 2-916 reco nfirming dyn amic VLAN ass ignments VTP co nfigu ring the ad ministrative d omain name 2-1 57 debuggin g 2-158 2-9 20 2 -924 co nfigu ring tun nel encapsu lation rate disabling debugg in g 2-921 co nfigu ring the device in VTP client mode co nfigu ring the device in VTP server mode co nfigu ring the device in VTP transp