A P P E N D I X E Installing the Wall Mount for the Cisco Unified IP Phone This appendix contains information about installing the wall mount for use with the following: • Installing the Wall Mount for Cisco Unified IP Phone 8961, 9951, and 9971 • Installing a Wall Mount for a Phone with a Key Expansion Module Installing the Wall Mount for Cisco Unified IP Phone 8961, 9951, and 9971 This section describes how to install a wall mount for the Cisco Unfilled IP Phone 8961, 9951, and 9971.
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone Installing the Wall Mount for Cisco Unified IP Phone 8961, 9951, and 9971 • 2 4-40x1/4 inch machine screws • 1 six-inch Ethernet cable • 1 key if the bracket includes the optional lock Before You Begin You need these tools to install the bracket: • #1 and #2 Phillips-head screwdrivers • Level You must also install an Ethernet jack for the telephone in the desired location if an Ethernet jack does not currently exist.
Installing the Wall Mount for the Cisco Unified IP Phone Installing the Wall Mount for Cisco Unified IP Phone 8961, 9951, and 9971 Figure E-2 Mounting the Wall Bracket A B Mark mounting holes through bracket on wall Level wall bracket on wall C D Insert anchors into wall Screw bracket to wall using Phillips head screws 274936 Appendix E Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 8.
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone Installing the Wall Mount for Cisco Unified IP Phone 8961, 9951, and 9971 Step 2 Attach the phone bracket to the IP Phone (Figure E-3). a. Detach the handset cord (and headset cord, if there is a headset), power cord, and any other attached cords from the base of the phone. b. Remove the label covers that are concealing the screw holes. c. Attach the phone bracket by inserting the tabs into the mounting tabs on the phone.
Installing the Wall Mount for the Cisco Unified IP Phone Installing the Wall Mount for Cisco Unified IP Phone 8961, 9951, and 9971 Step 3 Remove the handset wall hook in the handset rest, rotate the hook 180 degrees, and reinsert the hook. The hook should have a lip on which the handset catches when the phone is vertical (Figure E-4).
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone Installing the Wall Mount for Cisco Unified IP Phone 8961, 9951, and 9971 Step 4 Attach the Ethernet cable to the 10/100/1000 SW network port and wall jack. If you are connecting a network device (such as a computer) to the phone, attach the cable to the 10/100/1000 Computer (PC access) port.
Installing the Wall Mount for the Cisco Unified IP Phone Installing the Wall Mount for Cisco Unified IP Phone 8961, 9951, and 9971 Step 5 Attach the phone to the wall bracket by inserting the tabs on the top of the phone bracket into the slots on the wall bracket. Ensure that the power cord and any other cable that does not terminate in the wall behind the bracket are positioned in one of the cable-access openings in the bottom of the bracket.
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone Installing a Wall Mount for a Phone with a Key Expansion Module Installing a Wall Mount for a Phone with a Key Expansion Module This section describes how to install a wall mount for the Cisco Unified IP Phone 8961, 9951, and 9971 connected with the Key Expansion Module.
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone Installing a Wall Mount for a Phone with a Key Expansion Module Installing the Bracket To install the phone on the wall, perform the following steps: Note Be sure to connect to connect the Cisco Unified IP Phone to the Key Expansion Module before installing the phone bracket. Procedure Step 1 Mount the wall bracket in the desired location (Figure E-8).
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone Installing a Wall Mount for a Phone with a Key Expansion Module Figure E-8 Mounting the Wall Bracket A B Mark mounting holes through bracket on wall Level wall bracket on wall C D Screw bracket to wall using Phillips head screws 206799 Insert anchors into wall Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 8.
Installing the Wall Mount for the Cisco Unified IP Phone Installing a Wall Mount for a Phone with a Key Expansion Module Step 2 Attach the phone bracket to the IP Phone and key expansion assembly (Figure E-9). a. Detach the handset cord (and headset cord, if there is a headset), power cord, and any other attached cords from the base of the phone. b. Remove the label covers that are concealing the screw holes. c. Attach the phone bracket by inserting the tabs into the mounting tabs on the phone.
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone Installing a Wall Mount for a Phone with a Key Expansion Module Step 3 Remove the handset wall hook in the handset rest, rotate the hook 180 degrees, and reinsert the hook. The hook should have a lip on which the handset catches when the phone is vertical (Figure E-10). Figure E-10 Preparing the Handset Hook 2 3 4 192897 1 Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 8.
Installing the Wall Mount for the Cisco Unified IP Phone Installing a Wall Mount for a Phone with a Key Expansion Module Step 4 Attach the Ethernet cable to the 10/100/1000 SW Network port and wall jack. If you are connecting a network device (such as a computer) to the phone, attach the cable to the 10/100/1000 Computer (PC access) port.
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone Installing a Wall Mount for a Phone with a Key Expansion Module Step 5 Attach the phone to the wall bracket by inserting the tabs on the top of the phone bracket into the slots on the wall bracket. Ensure that the power cord and any other cable that does not terminate in the wall behind the bracket are positioned in one of the cable-access openings in the bottom of the bracket.
