Installation guide

ManualsBrandsCisco ManualsComputer equipment827 - 827 Router - EN

Corporate Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Cisco 827 Router Cabling and Setup

Quick Start Guide

This document describes the basic process of cabling and configuring the Internet access device, the

Cisco 827 router. For advanced cabling information, refer to the Cisco 827 Routers Hardware Installation

Guide. For advanced configuration information, refer to the Cisco 827 Routers Software Conﬁguration

Guide. These documents are available on the Cisco Documentation CD-ROM and on the World Wide Web.

You can access the most current Cisco documentation on the World Wide Web at the following sites:

• http://www.cisco.com

• http://www-china.cisco.com

• http://www-europe.cisco.com

Parts List

The shipment of your Cisco 827 router includes the following items:

• One Cisco 827 router

• One yellow Ethernet cable

• One lavender ADSL cable

• One blue console cable

• One DB-9-to-RJ-45 adapter (for use with the blue console cable)

• One black power supply

• One black power supply cord

• 800 and SOHO Series Product Documentation CD

Figure 1 shows the items included with the router. If any of the items is missing or damaged, contact

your customer service representative.

Summary of content (12 pages)

PAGE 1
Cisco 827 Router Cabling and Setup Quick Start Guide This document describes the basic process of cabling and configuring the Internet access device, the Cisco 827 router. For advanced cabling information, refer to the Cisco 827 Routers Hardware Installation Guide. For advanced configuration information, refer to the Cisco 827 Routers Software Configuration Guide. These documents are available on the Cisco Documentation CD-ROM and on the World Wide Web.
PAGE 2
Verify the PC Setup Figure 1 Items Included with the Router er at th t O en um oc D n io Yellow Ethernet cable rt ta S e ck id ui u Q G n tio ta en OM um -R oc D D C Lavender ADSL cable Product documentation Light blue console cable o c is C 0 80 Desktop power supply Black power cord Cisco 800 CD-ROM DB-9-to-RJ-45 adapter (for use with light blue console cable) Verify the PC Setup Before you begin, verify that each computer that will be connected to the router has a network interface card (NI
PAGE 3
Connect the Cisco 827 Router to a PC Connect the Cisco 827 Router to a PC Follow these steps to connect the Cisco 827 router to a PC: Figure 2 TO HUB TO PC Connecting a Cisco 827 Router to a PC ETHERN ET CONSO LE ADSL Model Ci sco 827- 4V +5,+12,- 12,-24,-71 PHONE 1 4 , VDC 3 2 1 Cisco 827-4V router OK SER 0 AUX LAN AUX PC Step 1 Connect the yellow Ethernet cable from the yellow Ethernet port on the back panel of the router to the Ethernet port on the NIC on the computer.
PAGE 4
Connect the Cisco 827 Router to a Hub Connect the Cisco 827 Router to a Hub Follow these steps to connect the Cisco 827 router to a hub: Figure 3 TO HUB TO PC Connecting a Cisco 827 Router to a Hub ETHERN ET CONSO LE ADSL Model Ci sco 827- 4V 4 Cisco 827-4V router +5,+12,- 12,-24,-71 PHONE 1 , VDC 3 2 1 1X 2X SPEED LED 100Bas eTX SO LID 10Base T BLI NK 10/100 3X 4X 1 2 3 4 5 6 7 8 5X 6X 7X 8X MDI MDI-X Cisco 1528 Micro Hub 10/100 Step 1 Connect the yellow Ethernet cable from the
PAGE 5
Connect an ADSL Line Connect an ADSL Line Follow these steps to connect an ADSL line to the ADSL port on your router. Note The following instructions are for a straight-through ADSL cable, but they also apply if you are using a crossover cable to connect your ADSL line. One ADSL cable is supplied with the Cisco 827 router, and it is selected during the ordering process. If you have microfilters or do not have the phone service on the same line, use the lavender CAB-ADSL-RJ11 cable.
PAGE 6
Connect a Telephone or Fax Machine Connect a Telephone or Fax Machine If you have a Cisco 827-4V router, you can connect an analog telephone or fax machine to your router. Use the cables provided with these devices. The gray PHONE 4, 3, 2, and 1 ports are RJ-11 connectors. If you are outside of North America, you must buy and attach adapters that allow your telephones or faxes to be connected to these RJ-11 connectors.
PAGE 7
Connect the Power and Turn On the Router Connect the Power and Turn On the Router Follow these steps to connect power to the Cisco 827 router and turn it on: Figure 6 Connecting the Power to a Cisco 827 Router TO HUB TO PC ETHERN ET Model Ci CONSO LE ADSL sco 827- 4V +5,+12,- 12,-24,-71 PHONE 1 4 3 2 To electrical outlet , VDC 1 8-pin connector Desktop power supply Step 1 Make sure the router power is off.
PAGE 8
Set Up the Router to Access the Network Set Up the Router to Access the Network The Cisco Router Web Setup (CRWS) software is already loaded on your Cisco 827 router. You can use CRWS to configure the Cisco 827 router. If you purchased your router through an Internet service provider (ISP), it is possible that your router has been configured for use at your site.
PAGE 9
Verifying the LEDs Verifying the LEDs The following table describes the normal pattern for LEDs and what to do if you get an abnormal pattern. For more information on all LEDs, see the Cisco 827 Routers Hardware Installation Guide. LED Normal Pattern OK Explanation If Abnormal Pattern On Power is supplied to the router. If off, see the Cisco 827 Routers Hardware Installation Guide. PHONE 1, 2, 3, 4 On Telephone or fax machine is connected.
PAGE 10
About the Product CD About the Product CD The 800 and SOHO Series Product Documentation CD contains the technical publications for the 800 and SOHO series routers. System Requirements Processor Pentium 150 MHz or faster recommended PC OS Microsoft Windows 95 Microsoft Windows 98 Microsoft Windows 2000 Microsoft Windows NT 4.0 Memory 64-MB DRAM Drives 4x CD-ROM drive Monitor Color monitor capable of 800 x 600 pixel resolution Software Netscape 3.0 or later Internet Explorer 3.
PAGE 11
About the Product CD Using the CD Interface When the CD is first launched, it automatically opens a browser session and displays the CD interface in the browser window. You can use the list of books in the left pane of your display to navigate directly to the book you want to view. Within the interface, you can use your mouse to: • Hover over book titles in the left column for an overview of the document before opening a document.
PAGE 12
About the Product CD AccessPath, AtmDirector, Browse with Me, CCIP, CCSI, CD-PAC, CiscoLink, the Cisco Powered Network logo, Cisco Systems Networking Academy, the Cisco Systems Networking Academy logo, Fast Step, Follow Me Browsing, FormShare, FrameShare, GigaStack, IGX, Internet Quotient, IP/VC, iQ Breakthrough, iQ Expertise, iQ FastTrack, the iQ Logo, iQ Net Readiness Scorecard, MGX, the Networkers logo, Packet, RateMUX, ScriptBuilder, ScriptShare, SlideCast, SMARTnet, TransPath, Unity, Voice LAN, Wavele