Specifications
Table Of Contents
- Cisco Unified Wireless IP Phone 7921G Administration Guide for Cisco Unified CallManager Release 4.1, 4.2, 5.0 and Later
- Contents
- Preface
- An Overview of the Cisco Unified Wireless IP Phone 7921G
- An Overview of the Voice Over IP Wireless Network
- Understanding the Wireless LAN
- Components of the VoIP Wireless Network
- Voice Over IP Wireless Network Configuration
- Site Survey Verification
- Setting Up the Cisco Unified Wireless IP Phone 7921G
- Before You Begin
- Installing the Cisco Unified Wireless IP Phone 7921G
- Powering On the Cisco Unified Wireless IP Phone 7921G
- Understanding the Phone Startup Process
- Using the Cisco Unified Wireless IP Phone 7921G Web Pages
- Using the USB Connection for Initial Phone Configuration
- Updating Phones Remotely
- Configuring Network Profiles
- Configuring USB Settings
- Configuring Trace Settings
- Using System Settings
- Configuring Settings on the Cisco Unified Wireless IP Phone 7921G
- Accessing Network and Phone Settings
- Configuring Network Profile Settings
- Changing Phone Settings
- Configuring the Security Certificate on the Phone
- Changing the USB Configuration
- Configuring Features, Templates, Services, and Users
- Configuring Cisco Unified Wireless IP Phones in Cisco Unified CallManager
- Telephony Features Available for the Phone
- Specific Configuration Options for the Cisco Unified Wireless IP Phone 7921G
- Configuring Softkey Templates
- Modifying Phone Button Templates
- Setting Up Services
- Configuring Corporate and Personal Directories
- Adding Users to Cisco Unified CallManager
- Managing the User Options Web Pages
- Creating Custom Phone Rings
- Viewing Security, Device, Model, and Status Information on the Phone
- Monitoring the Cisco Unified Wireless IP Phone Remotely
- Troubleshooting the Cisco Unified Wireless IP Phone 7921G
- Resolving Startup and Connectivity Problems
- Resolving Voice Quality and Roaming Problems
- General Troubleshooting Information
- Erasing the Local Configuration
- Providing Information to Users By Using a Website
- Supporting International Users
- Physical and Operating Environment Specifications
- Checklist for Deploying the Cisco Unified Wireless IP Phone 7921G
- Index
D-5
Cisco Unified Wireless IP Phone 7921G Administration Guide for Cisco Unified CallManager Release 4.1, 4.2, 5.0
OL-10802-02
Appendix D Checklist for Deploying the Cisco Unified Wireless IP Phone 7921G
Configuring QoS Policies
• AVVID Priority Mapping—Yes.
• WiFi Multimedia (WMM) on radio interfaces—Enabled
Controller Settings
For detailed information about configuring QoS policies for the controller, refer
to these URLs:
• http://www.cisco.com/univercd/cc/td/doc/product/wireless/control/index.htm
• http://www.cisco.com/univercd/cc/td/doc/product/wireless/control/c44/ccfig40
/index.htm
When using a controller, add the following QoS policies:
• Platinum (voice)—Apply this policy to your voice WLAN SSID/VLAN for
both incoming and outgoing traffic.
• Silver (best effort)—Apply this policy to your data WLAN SSID/VLAN for
both incoming and outgoing traffic.
• WLAN configuration screen for the voice WLAN SSID/VLAN—For the
7921G Phone Support field, check the AP CAC Limit checkbox to enable
QoS Element for Wireless Phones (QBSS).
• General Controller configuration screen—Set Aggressive Load Balancing to
Disabled.
Switch Configuration
To implement QoS in the connected Ethernet switch individual configurations
will vary; however, you can use this example of QoS commands as a guide.
mls qos
mls qos map cos-dscp 0 8 16 24 34 46 48 56
mls qos map ip-prec-dscp 0 8 16 24 34 46 48 56
interface FastEthernet0/00
switchport access vlan 11
switchport mode access
switchport voice vlan 111
no ip address
mls qos trust dscp
wrr-queue cos-map 1 1