Specifications
Table Of Contents
- Cisco Unified Wireless IP Phone 7921G Administration Guide for Cisco Unified CallManager Release 4.1, 4.2, 5.0 and Later
- Contents
- Preface
- An Overview of the Cisco Unified Wireless IP Phone 7921G
- An Overview of the Voice Over IP Wireless Network
- Understanding the Wireless LAN
- Components of the VoIP Wireless Network
- Voice Over IP Wireless Network Configuration
- Site Survey Verification
- Setting Up the Cisco Unified Wireless IP Phone 7921G
- Before You Begin
- Installing the Cisco Unified Wireless IP Phone 7921G
- Powering On the Cisco Unified Wireless IP Phone 7921G
- Understanding the Phone Startup Process
- Using the Cisco Unified Wireless IP Phone 7921G Web Pages
- Using the USB Connection for Initial Phone Configuration
- Updating Phones Remotely
- Configuring Network Profiles
- Configuring USB Settings
- Configuring Trace Settings
- Using System Settings
- Configuring Settings on the Cisco Unified Wireless IP Phone 7921G
- Accessing Network and Phone Settings
- Configuring Network Profile Settings
- Changing Phone Settings
- Configuring the Security Certificate on the Phone
- Changing the USB Configuration
- Configuring Features, Templates, Services, and Users
- Configuring Cisco Unified Wireless IP Phones in Cisco Unified CallManager
- Telephony Features Available for the Phone
- Specific Configuration Options for the Cisco Unified Wireless IP Phone 7921G
- Configuring Softkey Templates
- Modifying Phone Button Templates
- Setting Up Services
- Configuring Corporate and Personal Directories
- Adding Users to Cisco Unified CallManager
- Managing the User Options Web Pages
- Creating Custom Phone Rings
- Viewing Security, Device, Model, and Status Information on the Phone
- Monitoring the Cisco Unified Wireless IP Phone Remotely
- Troubleshooting the Cisco Unified Wireless IP Phone 7921G
- Resolving Startup and Connectivity Problems
- Resolving Voice Quality and Roaming Problems
- General Troubleshooting Information
- Erasing the Local Configuration
- Providing Information to Users By Using a Website
- Supporting International Users
- Physical and Operating Environment Specifications
- Checklist for Deploying the Cisco Unified Wireless IP Phone 7921G
- Index
3-17
Cisco Unified Wireless IP Phone 7921G Administration Guide for Cisco Unified CallManager Release 4.1, 4.2, 5.0
OL-10802-02
Chapter 3 Setting Up the Cisco Unified Wireless IP Phone 7921G
Installing the Cisco Unified Wireless IP Phone 7921G
To turn off the Found New Hardware Wizard when using the USB cable to charge
the phone, follow these steps:
Procedure
Step 1 Plug the USB cable into the Cisco Unified Wireless IP Phone 7921G.
Step 2 Plug the USB connector into the USB port on your PC.
The Found New Hardware Wizard dialog opens.
Step 3 To turn off the wizard, for Update New Software, click No, not this time.
Step 4 Next, click the button next to Install the Software automatically
(Recommended).
Step 5 After a time delay, the Cannot Install This Hardware dialog box appears. Click
Don't prompt me again to install this software.
Step 6 Click Finish to close the dialog box.
The phone briefly displays “USB Connected” on the status line.
While the battery is charging, the indicator light is red.
Step 7 When the battery is fully charged, the indicator light turns green. You can
disconnect the USB cable from the phone, and unplug the cable from the PC.
Installing and Using the Desktop Charger
The desktop charger can charge both the phone battery installed in the phone and
a spare battery at the same time.You can place the phone in the desktop charger to
use the speakerphone capability while charging the phone and battery. For
information about using the desktop charger speakerphone, refer to the “Using a
Handset, Headset, and Speakerphone” in the Cisco Unified Wireless IP Phone
7921G Guide.
To identify the desktop charger components and how to set up the desktop charger,
use
Figure 3-5.